Search Documents

By G. Mousavian, R. Bagheri, N. Dalili

Polypropylene (PP) and its composites have an increasing use in automobile and domestic industries. Since the published results on strain rate effect on yield behavior do not match, and there is a high attention paid for effect of nanometeric fillers on deformation behavior of composites, in this research the strain rate effect on yield behavior of PP and the effect of nanometeric fillers on deformation behavior of PP have been studied. Microscopic observations and tensile tests in different strain rates on neat PP samples and on samples filled with 5, 10 and 15 %wt have been used. A dramatic change in behavior for the modulus and post-yield slope curves when the strain rate is between 0.0433-0.05 s-1 has been observed. Microscopic observations on PP indicate a change in deformation mechanism from shear yield to crazing at the same strain rate that the change in behavior of curves occurs. It has been observed that in PP nanocomposites with higher amount of calcium carbonate, fracture in early stages of deformation occurs in lower strain rates. In other words for a fixed stain rate there is a critical filler percentage such that if the filler percentage is higher then early-stage fracture will occur. Similarly for a fixed filler percentage there is a critical strain rate and in higher strain rates early fracture will occur. The critical stain rate will decrease as the filler percentage increases and vice versa.

Jan 1, 2006

By Fumito Tanaka

The Converting Furnace (C-furnace) of the Mitsubishi process has solely provided opportunities for producing blister copper continuously from molten matte. Continuous converting originates from the proven technology for controlling the behavior of magnetite in lime-ferrite slag of the CaO-FeOX-Cu2O system. Recent improvements in the C-furnace operation have included the slag controls reflecting the impact of minor oxides on magnetite behavior. Although previous investigations focused on magnetite behavior, sulfur has also affected the C-furnace operation because it is of practical importance to avoid the precipitation of gypsum from lime-ferrite slag and the separation of matte from blister copper. This paper will quantify the behavior of sulfur in C-furnace with respect to the gypsum formation and matte separation, and discuss better controls for C-furnace operation.

Jan 1, 2006

By Clara María Lamus Molina

The following minerals found in the residual black sands from gold mining in El Bagre Antioquia (Colombia) were identified as having major economic interest: Ilmenite (FeTiO3), with an average of 49% of TiO2, frequently altered presenting crowns; lamellaes of rutile and alteration textures; titanomagnetite with up to 25% of TiO2; magnetite (Fe3O4) in individual grains or associated with others minerals as hematite and ferromagnesian silicates rutile (TiO2) with considerable quantities of Nb2O5(0.1-3.7%Wt); zircon (ZrSiO4) with 66%Wt of ZrO2 and monazite with an average of 63.43%Wt of REE, this frequently associated to xenotime and thorite forming textures as little drops. Analysis in EPMA and SEM/EDS showed percentages of minor elements and traces, thereby clearly establishing the applications of these minerals in diverse industries. Furthermore, a detailed granumetric study of the different minerals and textural relationships among them also allowed for establishing the basis for possible processing and exploitation.

Jan 1, 2006

By Peter B. Lilly

Thank you, Syd, for the kind introduction and for inviting me to give the Keynote Address at this very prestigious gathering of some of the finest intellect and talent in the domestic and international coal industry. CONSOL Energy has been a part of this conference for its entire 24-year existence. We have presented 27 papers over that time. CONSOL employees have also been members of the planning committee for the conference, and we have been pleased to support the event both financially and with many participants. So I am honored to be here with all of you this morning, especially during such a positive period for coal. You can just feel the enthusiasm in this room for our industry, and for this conference. I can tell you, there?s also a lot of enthusiasm and excitement in CONSOL Energy?s boardroom. And our enthusiasm is mirrored on Wall Street. But there remains an ironic twist to all of this attention. Even when times are good, the coal industry seems to go largely unnoticed by the mainstream. Outside of West Virginia and other coal-producing regions, the industry still seems to lack influence and support, at least here in America. As an example, last month, an ABC News crew visited our Blacksville 2 Mine, near here, to do a feature story on increased employment in the coal industry.

Jan 1, 2006

By Jan E. Nesset, Colin Hardie, Peter Radziszewski, Donald P. Leroux

"The successful introduction of new high intensity stirred milling technologies (e.g. IsaMill, SMDetritor) to the mining industry in recent years prompted Noranda-Falconbridge to initiate a study comparing these technologies to the conventional technologies of ball milling and existing vertical stirred mills (e.g. VertiMill). The study was unique in that it utilized the same material (Brunswick Mine zinc cleaner regrind mill feed), the same sizing instrument (a Malvern laser difractometer) and sampling protocol, and media size and type (for the high intensity stirred mills). The paper compares the net energy efficiency (kWh/t) of the various technologies, their power intensity (kW/m3) and product size distribution spread (P80/P20). A key finding is that media size is critical to achieving optimal performance. As part of the performance comparison, an analysis of the four methods of power measurement was made (Prony brake, shaft torque, grinding chamber reaction torque, “no-load” correction) and followed-up with an experimental test procedure using three of these methods. The findings include divergent results for power measurements and some explanations based on the observations are proposed. The direct shaft torque and Prony brake calibration methods are shown to be the methods most suitable for stirred mills.INTRODUCTIONThe motivation for the investigation reported here was the lack of a suitable comparison within the available literature of relative grinding efficiency for the emerging crop of new industrial fine grinding technologies. Such comparisons are potentially fraught with inconsistency, from ore samples and grinding media used, to testing methodology, to size measurement techniques, to the power measurements themselves. The collaboration of the industrial suppliers (at the time MIM Technologies and Svedala, now Xstrada Technologies and Metso Minerals) and McGill University (P. Radsiszewski) were sought in order to ensure as valid a comparison as possible. The work was performed between October 2000 and November 2002, led by the mineral processing group at the Noranda Technology Centre (NTC) in Pointe-Claire, Quebec. The paper is presented in two sections; Part A considers the different power measurement methods and a comparison of the results for the SMDetritor (SMD) technology, while Part B reviews the grinding performance of the 5 technologies investigated using the selected performance criteria."

Jan 1, 2006

By Frik Badenhorst, René Roux, Peter Terbrugge

This paper presents a case study where economics dictated an aggressive slope angle and where an appropriate slope management programme allowed successful completion of mining to 190m below surface. The Navachab Gold Mine is located in Namibia and is one of the few gold mines in that country. Mining by open pit methods commenced in 1990 with economics dictating an aggressive slope design to minimise waste stripping and make the mine viable. With steep slope angles in the design, and a steeply dipping footwall geology, it was necessary to introduce a comprehensive slope management programme. This required good mining practice in limit blast techniques with pre-splits and trims, and good housekeeping to effect a safe and economical operation. The slope management programme in addition required in pit mapping and logging procedures, regular survey monitoring evolving to a robotic Geomos system, as well as slope instrumentation to monitor stability. Two relatively large scale failures occurred at the mine, the second of which impacted on the east wall access ramp, while the first was confined to an operating stack. The paper describes the design and slope management techniques developed for the east wall.

Jan 1, 2006

By Steve Kral

For a state whose roots are in mining, most Colorado residents probably do not realize that the industry still contributes heavily to the state’s economy. In 2005, the industry contributed, directly and indirectly, about $8 billion to the state’s economy, according to the Colorado Mining Association (CMA). It employed nearly 10,000 people at mines and support businesses. And the mining industry in Colorado is one of the highest paying occupations in the state, averaging about $80,000 a year in wages and benefits. The state’s coal mining industry produced nearly 36 Mt (40 million st) of coal in 2005, valued at $800 million, the CMA said. That was seventh in the nation. And Colorado’s only major gold mine produced 10.2 t (329,000 oz) last year, valued at $124 million. That was third in the nation. And Phelps Dodge’s Henderson Mine produced about 12.7 kt (28 million lbs) of molybdenum, valued at $350 million. Colorado is the largest molybdenum producing state in the nation.

Jan 1, 2006

By Gregory M. Molinda

Historically, miners have known that roof rocks originally composed largely of mud were prone to slaking and deterioration when exposed to water and humidity. Mine Safety and Health Administration (MSHA) records show that roof falls are more prevalent in summer and late fall. Field data shows higher bolt loads and increased room convergence in summer months. Laboratory data shows that very high internal pressures can be generated by significant strain in clay-rich rocks. In summer months humidities ranging from 70-100% can cause rock strains up to 7%, and rock pressures of 14,000 psi, more than enough to break apart weak shales and fireclays. The National Institute for Occupational Safety and Health (NIOSH) conducted wet/dry immersion cycling of clay-rich rocks. Results show that the rocks most prone to moisture deterioration are fireclays, claystones, and sandy shales, all of which have disrupted bedding. Of the 7 mudrocks with a weatherability index above 40%, none showed consistent fissile bedding. Black shales were surprisingly resistant to wet/dry water immersion cycling. Generally, mixed rocks (stackrock), typically susceptible to horizontal stress, are more resistant to moisture-deterioration. Mine roof rocks tested with moisture sensitivity ratings above 50% (moisture sensitivity index ranges from 0-100 with 100 being the most sensitive) all came from mines which had roof skin problems and used supplemental support to prevent rock fall injuries. Some roof rocks showed lateral variability of moisture sensitivity values, suggesting the need for more samples in highly varying roof rocks. Swelling strains of mudrocks showed that almost all of the swelling occurred in the first 24 hours after immersion. The wet/dry immersion cycling test used provides an accurate, quick and inexpensive method for estimating the moisture sensitivity of mudrocks. With this information mine operators can begin to anticipate hazardous ground and prepare appropriate roof support.

Jan 1, 2006

By Timo Niitti, Antti Rinne, Janne Turunen, Sami Grönstrand

"This paper describes novel methods to enhance the flow dynamics of a mechanical flotation cell that can be applied to an existing installation. There are several reasons to alter the flow dynamics. The most common motivation is to improve the metallurgical performance of the cell, for instance, to improve the flotation recovery in particle size ranges that are normally difficult to recover.The flow dynamics enhancements are associated with the geometry of the rotor-stator area and additional features in the tank. The rotor-stator area has been modified to provide more concentrated turbulent kinetic energy or respectively more pumping efficiency with less attrition to the slurry. The tank can be fitted with various geometrical features, aimed to create a desired particle suspension profile. Depending on the targeted particle size range and application, badly selected or designed features can also have a negative effect on the metallurgical results.Besides new flotation equipment, the enhancements can be applied to existing flotation cell installations, thus enabling improvements in the mixing profiles, solids suspension, tank sanding and metallurgical performance of operating flotation circuits. Results of several tests carried out in existing plant operations are presented, concerning both flow variables and metallurgy.The common factor to above-mentioned enhancements is the use of modern computational fluid dynamics tools in the design phase, as well as the validation of the obtained CFD results in laboratory and production scale. Validated variables include mixing profile, power draw and local air hold-up.The paper demonstrates the effects of various flow geometries on the mixing profiles and metallurgical results of existing mechanical flotation cells. It shows how modern computational fluid dynamics analysis can be used to screen and select different approaches before carrying out costly trial-and-error experiments in plant scale."

Jan 1, 2006

Reverse sensitivity is a critical issue for all extractive activities. Extractive industries can only establish in the location of the particular resource sought to be extracted. Avoiding a location near sensitive activities (such as residential activities) may, therefore, be more difficult for extractive industries, than for other industry (such as dairy factories).   This paper focuses on the following matters: +        principles to be derived from case law, +       district and regional council approaches managing reverse sensitivity effects, and +        avoiding, remedying or mitigating reverse sensitivity effects in the future.

Jan 1, 2006

By G. Anger, J. Enser, H. Antrekowitsch, S. Koch

Homogeneous chemical composition and microstructure are always necessary, but not always attained in practice. As-cast aluminium alloys tend to have a segregation microstructure. Features of the cast structure, which affect subsequent processing or properties, can be altered by the homogenization. The main task of the Department of Nonferrous Metallurgy was to investigate the effect of homogenization treatment on precipitation hardening of aluminium alloys 6061 and 6082. The effect of the solution heat treatment (SHT) temperature on the mechanical properties was also analyzed. The homogenized and non-homogenized rolling slabs were produced according to the usual conditions and methods. The metallographic investigations were carried out on the as-cast samples, after homogenization, after the hot and the cold rolling mill, and after natural and artificial ageing. Then, Brinell hardness measurements and tensile tests were conducted on both alloys in order to examine the influence of the homogenization.

Jan 1, 2006

By M Haydon

How do you portray a large structurally and stratigraphically complex deposit to return a meaningful resource estimation, and produce a geological model that is useable for planning on a daily basis? The George Fisher Mine is located 22 km north of Mount Isa and forms part of XstrataÆs Zinc Group operations. It is currently a major producer of zinc, lead and silver in the region with an estimated total resource for all categories of 127 Mt at 100g/t Ag, 5.3 per cent Pb and 9.2 per cent Zn (June 2005). Production in 2005 totalled 2 647 492 wet tonnes for 317 699 kg Ag, 140 317 tonnes Pb and 230 331 tonnes Zn from underground operations. George Fisher (GF) consists of two deposits that are structurally complex on a mine scale, George Fisher North (GFN) and George Fisher South (GFS). Regional faulting has resulted in a 2 km long package of variably pyritic shale and siltstone that separates the deposits. This paper looks specifically at GFN. Distinct correlations exist between the two deposits based on stratigraphic matches; however, orebody characteristics, geometry and fault architectures differ significantly between the two. The deposits consist of multiple, sedimentary-hosted, stratiform orebodies from 2 to 25 m wide, separated by waste intervals of variable width. Each ore-waste interval is modelled as an individual geological domain. Structurally, George Fisher North (GFN) contains a series of major late-stage NE faults with dextral offset(s) of up to 130 m. Further complexity is added by NS, NW and NNE striking fault orientations that can produce either a loss or repeat of stratigraphy, local drag folding, orebody attenuation and block rotation. Due to this structural complexity and orebody offsets, domains at GFN are further divided into fault blocks (FB). The GFN model comprises eight FBs over a strike length of 1 km, all of which are modelled independently. As drilling progresses and additional resources are converted, further FBs will be added at major fault offsets to accommodate orebody and model expansion. This will be in addition to what is already a large and time-consuming data set to manage and update. For example, each FB has 18 domains each with two constraining wireframes (hanging wall and footwall). Each wireframe has several sets of point data depending on the type of data available, ie diamond drilling, mapping or interpretation points. This equates to over 1100 separate files to manage. Additional wireframes and files are also required for major structures, daily planning requirements and block model runs. In total some 1500 files are managed, updated and maintained for GFN alone. The ongoing need to expand as a business and optimise production in the current economic climate where there is a global demand for metal has led to an increase in production at GF. This has resulted in a rapidly growing data set and highlights the importance of practical and efficient modelling to achieve a meaningful resource estimate. This paper focuses on the geological modelling, modelling approaches and techniques employed for the GFN deposit.

Jan 1, 2006

By N Meadows, M Rodriguez

A 200 000 tpa heap leach demonstration plant was approved by the Murrin Murrin Joint Venture (MMJV) in December 2005 and engineering commenced in January 2006. The demonstration plant will utilise stockpiled ore reject material (æscatsÆ) and extract nickel and cobalt. Limited production from the demonstration plant is expected by the end of 2006. The demonstration plant will enable the company to fully investigate and understand all associated technical issues over the next 12 to 18 months, including the potential to expand the heap leaching operation to a commercial scale. In parallel, the MMJV will continue a research and development program to improve and expand the application of its heap leaching technology.

Jan 1, 2006

By Ludovic Charpentier

Production of metallic wires directly from liquid jets would avoid drawbacks of extrusion (space needed, damaging, cost?) and enable recycling. But liquid jets tend to break, due to capillary instabilities, unless a solid layer (coating or start of solidification) surrounds it. We recently developed a process to produce tin wires, cooled by water flow parallel to the jet. Superficial oxidization of tin produces a glass coating around the jet. Studies showed the length of wires increased when increasing speed of tin jets, and that water average speed should be the closest possible to the jet one to have smooth fibers. Producing 1 mm diameter wires is possible. The length of wires is limited by the experimental setup, which does not provide possibilities to coil the wire. Most of other metals do not generate glass-like oxides. The lack of coatings makes it necessary to reduce the capillary instabilities to obtain fibers.

Jan 1, 2006

Accurate hematite solubility data are required to construct predictive solution chemistry models for complex hydrometallurgical solutions. These data are useful in understanding Fe(III) speciation and precipitation in a variety of hydrometallurgical processes. Hematite solubility data were generated in 10 to 70 g/L H2SO4 solutions and at temperatures from 130 to 270°C, using specially modified titanium autoclaves. These measurements represent an improvement over previous experimental data because of better in-situ filtration of the sample aliquots, the approach to equilibrium via hematite dissolution, and the inhibition of Fe(III) reduction on titanium surfaces. Fe(III) reduction was particularly studied to evaluate the inflationary effect of Fe(II) on hematite solubility measurements. Chromate was found to reliably inhibit Fe(III) reduction on titanium. Finally, the generated hematite solubility data were used to construct a solution chemistry model using the OLI software.

Jan 1, 2006

By Georgene Renner, William R. Yernberg, Steve Kral

Agapito Associates (AAI) provides consulting services in geo-engineering, mining engineering and related disciplines. Founded in 1978, the firm operates out of offices in Grand Junction, CO, Golden, CO and Lombard, IL. Members of the staff include mining, civil and geological engineers, physicists, geologists, numerical analysts, computer specialists, instrumentation specialists, plus administration and technical support personnel. AAI has provided consulting and engineering services to mining companies producing base metals, precious metals, coal, potash, trona, limestone, oil shale and salt, and to defense and nuclear-waste disposal industries. AAI also provides services for measuring in situ horizontal stresses using an advanced biaxial overcore stress downhole measurement system developed by Sigra of Australia. Since 1978, AAI has measured in situ stress in copper, oil shale, molybdenum, trona, limestone and coal mines, and in tunnels and concrete structures. Since 1994, the staff has completed 527 overcore stress determinations. AAI has the equipment and personnel for overcoring, sample coring and instrumentation installation in limited access, surface and underground mines. Portable Longyear CP-65 drills, borehole deformation gauges and strain indicators are used for difficult-access overcoring and are permissible for use in gassy mines.

Jan 1, 2006

The selection and implementation of the right technology for a project is critical to the future development of the resource industry. It is essential for companies to ensure ongoing competitive viability that where practical new or alternative technology be adopted. Analysis of historical data relating to development of resource-based process plants provides an enlightening insight into the key factors which influence their success or failure. The adoption of new technology does not guarantee the success of a project. The outcomes of this analysis have been used to develop some general guidelines and principles the author believes are useful in the selection and implementation of new or alternative technology in resource projects. This paper is available as a PowerPoint presentation only.

Jan 1, 2006

By Valentine A. Chanturiya

The aim of this paper is basically to show progress in the study of nanosecond processes involved in the disintegration and breaking-up of mineral complexes with fine noble metals. We studied the influence of nanosecond High-Power Electromagnetic Pulses (HPEMP) on the physical and technological properties of refractory gold-containing ores and beneficiation products. Experimental data are presented to confirm the formation of breakdown channels and selective disintegration of mineral complexes as a result of pulse irradiation, which makes for efficient access of lixiviant solutions to precious metal grains and enhanced precious metal recovery into lixivia during leaching. Preliminary processing of gravity concentrate with a HPEMP resulted in significant increase of gold and silver extraction into lixivia during the cyanidation stage, with gold recovery increased by ~31% (from 51.2% in a blank test to 82.3% after irradiation). Gold recovery from stale gold-containing dressing tailings products increased after pulses-irradiation from 8-12% to 80-90%.

Jan 1, 2006

By Kot F. v. Unrug

The present combination of coal market prices and reserves, situated in the Central Appalachian Coal Field, is such that mining of smaller coal reserve blocks has become economically attractive. In above drainage deposits, and particularly under mountain ridges, overburden depth can be changing within a wide range. Mines operating in these deposits are usually developing mains along the center of the ridge, with panels projecting from the mains towards the outcrop. Due to changing topography, proximity of the outcrop, and related cover depth, the panels have various lengths. In this reported case study, a mine in Pike County, Kentucky, along the Kentucky ?West Virginia border, difficult ground conditions were encountered, during the development of the mains, under shallow cover, along a narrow mountain ridge. An area having unusual density of vertical joints was encountered. Mining operations were suspended because of roof stability concerns. The ground conditions were studied, analyzed, and control measures proposed to ensure safe passage through the difficult roof area of the mine. The advancement of the mains, through this area of challenging ground conditions, was successfully completed. In this paper, ground conditions are described, with an explanation of the geologic process contributing to their formation. It is interesting to note that similar locations were predicted by the authors, to be encountered in the same mine, based upon the experience gathered from studying conditions of the case described within this paper. When approaching the predicted locations, stability problems appeared to be even more challenging than those encountered previously. Due to changes in the coal market, mine management chose to move the affected mining section to another area of the mine having better coal quality. The advancement of the mains, through the difficult ground conditions, was temporarily postponed. Based upon the analysis of a probable kinematical mechanism of blocks in the mine roof, ground control measures were proposed. The actual application of these principles proved to be appropriate, ensuring safe passage through the difficult ground conditions encountered in the mine.

Jan 1, 2006

By C Glassock, P Tilyard, T Sandeman

Computer simulation is a well accepted tool for modelling the behaviour of large and complex operating systems. It is a particularly useful technique in complex operations where there are multiple interactions between the inputs and outputs of various unit operations. It can be utilised during the early stages of a project as part of the business case definition phase or the early engineering phases, or alternatively to help understand the various options available in an upgrade or expansion. With the design of a new processing plant to handle a different ore type at Lihir Gold Limited (Lihir), there was concern that the existing conveying system could separately handle the increased tonnages. A simulation model was constructed which allowed Lihir to examine the impact on the conveying system of the new process plant, as well as investigate the effect of different trucking options. As is often the case, once the simulation model was built, further understanding of the downstream bottlenecks was able to be investigated, including the sizing of critical equipment.

Jan 1, 2006