Search Documents

By Y. El-Mossallamy

The piled raft foundation was extensive applied in the last two decades in different soil conditions e.g. in soft to stiff clay as well as in medium to dense sand and even in highly weathered rock. The piled raft is now applied not only to control the foundation settlement but also to minimize the required raft thickness to reach the most economic foundation design. An innovative application of the piled raft is its special adjustment to cases of foundations with large load eccentricities or very different loaded parts of buildings to avoid the need of settlement joints, which are especially complex below ground water table. Recently, the piled raft is applied for foundations of highway and railway bridges with special serviceability requirements regarding the allowable total and differential settlement as well as tilting. Actually numerical analyses are the mostly used design methods for piled rafts. For all day design practice a simple and modest design method is highly needed -at least in the first design stage- to check the feasibility of the piled raft on the specific project conditions. In this paper, a general overview on the recent innovative applications of piled rafts in Germany will be presented in a short overview. The results of the simple design method will be discussed and compared with the results of more enhanced numerical methods.

Jan 1, 2006

By P. P. Rosario, D. M. Maijer

The primary crusher is a key component in the comminution process applied in open pit mines. A collaborative research project between the University of British Columbia and Highland Valley Copper (HVC) was conducted aiming at understanding gyratory crusher liner wear in the overall context of the crushing process. This paper presents an analysis methodology applied to data collected using a laser-based tool for assessing wear in gyratory crushers. Data from the wear measurements was correlated with crusher production information such as current draw and throughput. As a result of the knowledge developed during this work, an innovative way to evaluate crusher liner profiles was created and new mantle profiles were designed. This led to a reformulation of HVC’s standard liner management policy with a resulting estimated annual savings of 13% in total crusher liner cost and a 15% reduction in liner replacement downtime.

Jan 1, 2006

By J. Morkel

During research on mainly the weathering of kimberlite, it became evident that its mineralogical composition is an important factor in the complex process of physical and chemical disintegration. The mineralogy of tuffisitic kimberlite breccias from two localities, the Cullinan and Venetia mines, is compared with special reference to the occurrence of associated clay minerals. The clay mineral composition influences the engineering properties of these rock types. It is illustrated how the presence of swelling clay components can be confirmed by ethylene glycol treatment and chlorite minerals by heat treatment using X-ray diffraction. Smectites are present in both tuffisitic kimberlites, dominant at Venetia while chlorite is more frequent at Cullinan. More tuffisitic kimberlite breccias samples from venetia were also characterized. It was found that kimberlite disintegration is correlated with the presence and abundance of smectite.

Jan 1, 2006

By John O. Marsden

The past fifteen years have seen a number of important developments in copper hydrometallurgy, including the commercial application of biological heap leaching of secondary (chalcocite-dominant) copper ores, the commercial demonstration of chalcopyrite concentrate leaching technology using pressure leaching and biological processes, and the application of novel configurations of solution extraction circuits. Significant emphasis is now being placed on the development of effective stockpile leaching practices for primary ores (chalcopyrite and bornite-dominant mineralization). Some of these developments have been highly successful, and will pave the way for further development and commercialization. Others have been less successful. These developments are reviewed in the context of the metal price cycle and trends for the future are identified.

Jan 1, 2006

By E. Özberk

Uranium minerals are often associated with iron minerals, and during the hydrometallurgical processing of the uranium ores, iron plays several significant roles. The presence of Fe(III) in solution promotes the oxidative acid leaching for the recovery of uranium. The control of the distribution of impurities in milling and refining is also affected by dissolved iron. When rejected from the process streams, iron usually collects other impurities and contributes to the stabilization of the wastes for final disposal. These roles of iron, as they relate to current uranium processing operations, are discussed in detail, and some broad and historical perspectives are also presented.

Jan 1, 2006

By Paul Hughes

This paper describes a focus of work presently being conducted at the Rock Mechanics Research Group at the University of British Columbia. The underhand method under consolidated fill ensures a high recovery under an engineered back that is comprised of cemented rock fill and/or cemented paste fill. This method of mining has been employed successfully in mines throughout North America as a method of mitigating exposure to the operator having to work under a seismically active ?back?. This paper reviews design methodology in the placement and analysis of sill mats with reference to site observation coupled with on going numerical and analytically derived solutions.

Jan 1, 2006

By D. J. H. Walker, W. H. Gibson

The inclination of any pit wall composed of stacks of benches is limited by the overall quality and structural complexity of the rock mass in which the slope is situated. For a bench stack angle that satisfies the stability criteria, various combinations of bench height, bench face angle and berm width can be used in the slope design. The bench face angle and berm width geometries must be chosen to fit the bench stack angle but must provide a berm that will be capable of catching the volume of failed wedge material from the bench faces above. Other considerations for bench height and berm width are equipment size, ore selectivity and blasting design. This paper studies the effects of different slope configurations on slope performance as it relates to wedge stability, volume of rock safely contained on berms, and rockfall. Optimisation of the geometry is carried out based on the need to minimise the volume of failed material which limits the effectiveness of the berm. This will reduce the number of rocks that can continue to fall further, reaching geotechnical safety berms or pit ramps, that put safety of personnel and equipment at risk. For general study it is most effective to investigate and compare the performances of each of a wide range of geometrical combinations of bench height, bench face angles and berm widths that fit a variety of different bench stack angles. These analyses were conducted for a predetermined bench stack height and three different bench stack angles.

Jan 1, 2006

By Aly M. Mohammad

State and federal agencies during rehabilitation of existing bridges may require the existing bridges to be evaluated under seismic conditions. If the bridge does not perform under the seismic event, the bridge may require seismic retrofitting. Bridges are classified as: Critical, Essential, and Others according to their importance. Geotechnical considerations play a major role in evaluating the bridge behavior under a seismic event. Subsurface conditions influence the magnitude of ground acceleration and hence the forces and moments on the superstructure. This paper will provide a detailed description of the geotechnical aspects associated with the seismic retrofit evaluation for the 12th Street and 14th Street Viaducts located in Jersey City, New Jersey. The paper will also present a description of the geotechnical investigation program including seismic cross-hole surveys to determine the dynamic soil parameters, including the results of site-specific response spectra for both the 475 and 2475-year events. Liquefaction assessment methodology utilizing an equivalent factor of safety will also be described and the design method used will be summarized. In general, the pile foundation is modeled as 6x6 foundation stiffness matrix with 36 stiffness coefficients at the center of the pile cap. The seismic loading on the foundation is evaluated in a pseudo-static analysis, where the dynamic earthquake-induced loads are presented by static forces and moments. The computer program FB Pier was used to evaluate the foundation stiffness. The moments, axial loads, and shear are input into the FB Pier model. The stiffness of the foundation is determined and the results are then input into the Structural model to determine new forces and displacements. Adjustments are made until the loads are compatible with the stiffness used. The understanding of the geotechnical conditions at the 12th Street and 14th Street Viaducts and the coordination between the Bridge and Geotechnical Engineers were able to provide significant cost saving to the Owner. The Design Engineers were able to retrofit the existing Viaduct foundations with reasonable number of additional piles. It is believed that the results and finding presented in this paper will benefit both the Bridge Engineers and Geotechnical Engineers by highlighting the importance of interaction between the two disciplines.

Jan 1, 2006

By N. Q. Huy

This paper describes the application of finite element analysis to simulate the static and quasi-static pile load tests in different drainage conditions. The possible effect of excess pore water pressure will be studied from the simulations results. The results show that the drainage condition has effect on the bearing capacity of a pile derived from the quasi-static pile load test. The excess of pore pressure reduces the pile toe resistance while it increases the pile shaft resistance. The factors which influence the effect of excess pore pressure are also discussed.

Jan 1, 2006

By Mark Bauckman

Discussion Topics • Market Needs • Technology Developments & Best Practices • Industry & Government Developments • Future Possibilities & Your Role

Jan 1, 2006

By M. Potesser

In the primary and secondary copper industry the anode furnace is the most important process step in the refining procedure to reach an enhancement in value and quality of the copper by a selective oxidation and reduction. By combining the advantages of the conventional tilting hearth anode furnace and the benefits of the drum type anode furnace a new aggregate was developed and patented. The cross-section of the furnace is elliptical and the whole unit is tiltable. During the melting period, the contact surface between the burners and the bath or the scarp is enlarged - an increased energy input is the consequence. For the refining period the furnace is rotated, whereby a high bath level is guaranteed. Due to the longer residence time of the gas in the copper melt, not only the gas consumption is reduced but also the efficiency/quality of the refining process is improved. This investigation shows a metallurgical comparison between the new anode furnace concept with the elliptical profile/cross section and the conventional, tiltable hearth anode furnace as well as the drum type anode furnace. The CFD modeling of the currents in these different furnaces delivered helpful data to compare the geometry of the different furnaces. The investigation covered the refining of blister copper from primary metallurgy, from secondary metallurgy as well as from a mixture of both copper melts. The paper underlines the possibilities for a reduction of the tap-to-tap time and for an increase in production capacity, which can be achieved by applying the new furnace concept in comparison to the conventional furnaces.

Jan 1, 2006

By W. Keilich

A methodology of subsidence prediction using the Distinct Element code UDEC has been developed as an alternative for subsidence modelling in the Southern Coalfield, New South Wales, Australia. The models have been validated by comparison with empirical results and observed caving behaviour. At this stage, modelling capability is limited to flat lying terrain. It is planned to apply the methodology to areas of high topographical relief to investigate the mechanics of valley closure.

Jan 1, 2006

China’s vibrant economic growth is built on coal, the source of two thirds of the country’s electricity. Over 95 percent of China’s coal is mined underground with the average mining depth at 410 m and in-creasing at 10 m per year; today, the deepest Chinese coal mines have exceeded 1,000 m. With increasing mining depths, there are greater challenges including increased methane emissions and spontaneous combustion. According to the government, nearly half of China’s coal mines are classified as gassy (with specific gas content at least 10 m3/mt). Coalbed methane (CBM) is a clean energy source. However, only a small percentage of the methane is captured, and the rest is vented directly to the atmosphere. This paper describes China’s CBM resource, its production and utilization.

Jan 1, 2006

By Dallas Grubbs

Agenda ?Growth Projections ?Economic Indicators ?Mining Equipment Growth ?Tire Supply ?Michelin Actions to Increase Capacity ?Michelin?s Challenges & Recommendations

Jan 1, 2006

The mineralogy of the platinum group metals is fairly complex, and it is therefore not surprising that the different minerals have variable responses to metallurgical processes, in particular, flotation and leaching. The PLATSOL® leach process was developed to extract simultaneously base metals, gold and platinum group metals from various materials. Extensive research has indicated that most PGM?s were amenable to the PLATSOL process, with the notable exception of cooperite PtS. Further work showed that a thermal pretreatment at 500-700ºC transformed the structure of the cooperite and similar refractory minerals (Pt,Pd)S into Pt metal and Pt-Pd alloys that responded well to the PLATSOL® process. Examples are presented of the mineralogy of PGM concentrates as produced, in the residue from the PLATSOL® leach and after thermal pretreatment.

Jan 1, 2006

Iron control and iron residue management and disposal are significant issues in all zinc production processes. This paper briefly reviews the most important primary zinc production routes and discusses the challenges posed by iron control in each of them. The technologies and strategies that have proven successful in controlling and managing iron are discussed. SNC-Lavalin's experience in designing and commissioning zinc plants provides a unique perspective from which to review this aspect of zinc production.

Jan 1, 2006

This presentation is a 20 minute snippet of my professional career, and my progression in the mining industry, from a lazy uni student to an up-and-coming blast engineer in the middle of a mining boom.My name is Daniel Hepburn and I am a blasting engineer for Orica Mining Services. I graduated from Royal Melbourne Institute of Technology (RMIT), in Melbourne in 2003. I completed both of my final year projects with Orica Quarry Services and was offered an assistant shotfiring job, which I accepted and worked for eight months. Having missed the cut-off date for the Orica graduate program, I planned to work with Quarry Services until the following year where I hoped my marks and the experiences I had gained would secure a graduate position. I didnÆt have to wait long, as in August of that year, I was offered (and I accepted) a graduate position in Perth as a technical services engineer for Orica Mining Services. The Orica graduate program is based over two years, and consists of real roles from day one; however, there is also opportunity to fast track the program for high performers. There is a structured rotation, from site to site, interstate or even international if you are so inclined. This includes the backpacker program, which allows graduates to experience the Orica culture in countries of their choice. There are also opportunities to try cross-functional roles in the different Market segments within Orica. I was lucky in that I knew what I wanted to do and where I wanted to work, so I stayed in Perth for my entire graduate program. I was also lucky enough to be fast tracked and finished my graduate program in 15 months. At the end of 2005 I accepted a position as an open cut blasting engineer based in Perth and even in such a short period of time I have already completed a number of major accomplishments. Some of these accomplishments are described below. This paper is available as a PowerPoint presentation only.

Jan 1, 2006

By Tiebao Yang

In high pressure die casting processes, a die plays a critical role in removing heat from the molten metal during the cavity filling and solidification stages. Proper control of die temperature is essential for producing superior quality components and yielding high production rates. This paper proposes a local temperature control scheme for die thermal management based on a computerized intelligent real-time monitoring and control system (IRMCS). In this scheme, cooling water lines are controlled by a pump and solenoid valves. A controller is designed according to the law of die temperature fluctuations. The results obtained from the experiments carried out on a laboratory die casting process simulator indicate that the controller can limit the local die insert temperatures in a given band. Hence, the desired thermal pattern of the die insert becomes achievable.

Jan 1, 2006

By R N. Robson, A B. Christie, I J. Graham

Strategy development by the minerals industry identified the fragmented management of mineral resources as a significant impediment to the discovery and development of New Zealand Æs mineral resources. The total gross value of New Zealand Æs potential resources of coal and minerals is estimated at about $400 billion, but their potential value is not being realised. The management of minerals is now largely under the control of 86 local authorities (regional and district councils) and the lack of recognition of the significance of the sector has lead to inconsistencies in the way minerals are managed. The industry strategy influenced science funding for minerals, with the result that the 'mineral wealth' component now includes research on making better use of resource data in minerals management. Initially this research has targeted Otago and Northland regions where a number of initiatives are now in progress.   In Otago the Regional Council has budgeted to contribute $1 million towards a regional geophysical survey to advance mineral exploration and the management of subsurface resources in the region, to work cooperatively towards improving public awareness of the significance of minerals to regional economic activity, and to better coordinate policy-making for minerals at regional and district levels.   Crown Minerals, and the Far North and Whangarei district councils are considering providing funding support for an economic study of the mineral potential of Northland, building on a mineral resource assessment undertaken by GNS Science. Enterprise Northland is adding minerals to their list of potential growth sectors, and is supporting the operation of a Northland region minerals focus group.   Regional development agencies and local authorities have shown that they are willing to include mineral resources in their development strategies and to provide for them in policies and plans when supplied with information and assisted with technical support.

Jan 1, 2006

By E. S. Geskin

New material processing tools should be developed and reduced to the practice in order to meet the challenges facing the contemporary material production industry, One of such potentially important tools is supersonic liquid projectiles. It was shown that at the speed of 1500-1750 m/s the water projectile are able to demolish reinforced concrete plates, forge, to pierce and weld metals, to destroy with no explosion non dischargeable mines, etc. These projectiles are generated by simple, low cost launchers run. It is obvious that these projectiles can be applied to the ore mining and comminution. Thermodynamic considerations show feasibility of the use of these projectiles also for smelting, refining and forming. The presented paper discusses the results of the experimental study of supersonic liquid projectiles as well their potential metallurgical applications.

Jan 1, 2006