Search Documents

By Stone I

Tahmoor Mine is located in the southern Sydney Basin 80km south-west of Sydney and produces 1.2 MT of Bulli Coal annually. Bord and pillar methods used to date will be supplemented by a longwall system. Difficult roof conditions have been experienced since mining began in 1979. A dominantly horizontal stressfield promotes shear failure in the thinly interbedded roof sequence of shales, laminites, siltstones and fine sandstones. General roof conditions and failure characteristics are related to the angle between the roadway direction and the principal horizontal stress direction. The apparent stressfield changes direction, magnitude and the ratio of principal horizontal components across the mine workings in response to both in situ and mining induced causes. Initial roof support of 5 x 2.1 m bolts per W-strap at in intervals, with mesh, was upgraded to include RSJ's in order to support areas of failed roof. This support system was inefficient and costly. A third system of support emphasizes roof reinforcement with full resin encapsulation of 2.1 m bolts in W-straps. The number of bolts per strap (6-8), extra butterfly straps and bolts, and W-strap spacing is determined for each area by expected roof and stress conditions. Intersections are pre-bolted and ribs are supported in some areas. Pillar dimensions, order of drivage and roadway width have each been altered to improve roof control. The intensity of roof deformation at the face varies from panel to panel and causes development rates to decrease to 30% of the maximum. 1. Manager, Tahmoor Mine, Tahmoor, N.S.W. 2. Senior Geologist, BP Coal, Picton, N.S.W. Roof conditions in each area of the mine are characterised and then projected to future development areas based on the relationship between stressfield orientation, relative roadway direction and face conditions. Planning information available includes expected development rates, roof support requirements and areas of changing conditions. Future improvements of strata control involve defining support design parameters for the range of mine conditions already seen at Tahmoor.

Jan 1, 1986

By A. Halim, A. Martikainen, S. GYAMFI

This paper outlines a unique case of the development of strategies to reduce ventilation and heating costs in Konsuln iron ore mine in northern Sweden. The mine, located just south of Luossavaara-Kiirunavaara Aktiebolag’s Kiruna iron ore mine, was developed as a test mine from 2018-2020 for the Sustainable Underground Mining (SUM) project. Besides functioning as a test mine, Konsuln also contributes to ore production. The existing mine ventilation system was designed for the current production rate of 0.8 million tons per annum (Mtpa). There is a plan to increase this rate to between 1.8 and 2.0 Mtpa.

Dec 23, 2021

By A. Martikainen, S. GYAMFI

Luossavaara-Kiirunavaara Aktiebolag’s (LKAB) Konsuln iron ore mine, located just south of the famous Kiruna iron ore mine in Malmfälten in northern Sweden inside the Arctic Circle, was developed as a test mine between 2018 and 2020 for the Sustainable Underground Mining (SUM) project [1]. Besides functioning as a test mine, Konsuln also contributes to ore production. The existing mine ventilation system was designed for the current production rate of 0.8 Mtpa using conventional diesel machines. The design was created by Kiruna mine ventilation team, Stina Klemo and Joakim Jonasson, in cooperation with a consultant, Tomas Bolsöy from EOL Vent Mining AB. There is a plan to increase this rate to between 1.8 and 3 Mtpa in the future, and this requires the primary fans to be upgraded. Therefore, a study was carried out to determine whether using ventilation on demand (VOD) could avoid this fan upgrade and reduce Konsuln’s ventilation and heating power costs in the future. The study also investigated whether using battery electric vehicles (BEVs) along with VOD or as a standalone strategy could further reduce these power costs. In addition, the study analyzed the suitability of heating power reduction strategies presently or previously used in Nordic countries and Canada to investigate potential additional strategies to reduce heating power cost, the largest portion of Konsuln’s ventilation and heating power costs.

By Eric G. Zahl

Researchers at the Spokane Research Laboratory of the National institute for Occupational Safety and health are evaluating stress and displacement measurements in a longwall coal mine. The objective is to determine the best indicators of coal bump hazards during operations so that mine foremen and technical stall can make more informed intervention decisions to protect miners from coal bumps. Instruments were clustered in two panels, a yield pillar, and the immediate roof and floor of a two-entry longwall coal mine. Data were gathered continuously from a variety of instruments as mining proceeded toward and past the instrument cluster. Researchers and the mine's technical staff evaluated these data with respect to coal bumps and bump mechanisms. Selected graphs were then presented to mine foremen on a periodic basis to test their usefulness in identifying hazards. Of particular interest was the use of horizontal stress data from the immediate roof. To measure changes in horizontal stress, a new technique was devel¬oped for installing a grouted biaxial stressmeter in the roof. An evaluation of the development of this stress monitoring system in producing data beneficial to mine foremen is presented.

Jan 1, 2000

By Robert P. King

In April, 1975 the Colorado School of Mines began monitoring rock mass response associated with a long- wall shield demonstration project near Raton, New Mexico. This project was sponsored by the U. S. Bureau of Mines (DOE) and performed at Kaiser Steel Corporation's York Canyon Mine. Two of the results of the intensive instrumentation effort are the empirical subsidence and horizontal strain models presented herein. These models are based on data gathered during mining three adjacent longwall panels (4N, 5N and 6N). A total of 251 permanent surveying monuments were monitored over the three-panel area. Lines of monuments were oriented along panel centerlines, perpendicular to centerlines and diagonal (45O) to centerlines. Active monuments were monitored twice a week, with less frequent monitoring of stable or slow moving monuments. Primary subsidence monitoring equipment consisted of an AGA Geometer Model 75 and a Wild T-2 Theodolite with -a Wild-Sercel DI-3S distomat.

Jan 1, 1979

By P. Schilizzi

The increased impact of mining subsidence in the U.S. coalfields and the recent regulatory constraints legislated by government and state agencies have provoked an intense research effort on this topic by government agencies, coal companies and academic institutions. Subsidence and horizontal strain predictions are a basic requirement if subsidence and its associated effects are to be controlled and contained within acceptable environmental levels. As a result, several such prediction techniques have been proposed or are currently under development to assist coal operators in minimizing the detrimental effects of these surface deformations. VPI&SU has been actively involved in this research effort in the past few years, with particular emphasis on the Appalachian coalfield. During the initial stages of this research a large number of subsidence case studies were collected from the literature, the coal industry and government agencies. In total, data from 32 longwall panels and 60 room and pillar panels were collected. This data bank was used to determine relationships between the basic mining and subsidence parameters, in order to allow the evaluation of the various prediction methods for the Appalachian coal region. Based on this data two subsidence prediction techniques, one based on profile functions and the other on influence functions have been developed. Profile function methods provide a tool for a fast calculation of subsidence on a line across a mine panel. Influence function methods, on the other hand, allow for a more detailed calculation of ground movements, in any mode and at any depth, on a grid or at any specific point. The limitations of the data of the collected case studies, i.e. accuracy of surveys, frequency of monitoring, lack of horizontal movement measurements, etc, led VPI&SU to the initiation of a detailed subsidence and strain monitoring program above a number of active mines, located in three major coal producing counties of Virginia. The aim of this program was to enhance the data base with accurate and complete measurements of surface movements and to allow, therefore, the refinement of the prediction techniques. This paper presents this monitoring program, discusses in detail the results obtained from three specific case studies and provides recommendations for the implementation of the field data in the general prediction methods.

Jan 1, 1986

By D. K. Dysinger

The U.S. Bureau of Mines investigated leaching of chalcopyrite with sulfuric acid-oxygen under conditions anticipated during in situ leaching. A central composite experimental design was chosen to study oxygen pressures of 150, 300, and 450 psi, leach temperatures of 35?, 65°, and 95° C, oxygen-to-chalcopyrite mass ratios of 0.5, 1.0, and 1.5, leach times of 8, 16, and 24 hours, initial acid strengths of 0.6, 1.2, and 1.8 g H2SO4/g chalcopyrite and pyrite to chalcopyrite mass ratios of 0, 1, and 2. The leaching kinetics were consistent with the shrinking core model. A quadratic response surface model was used to determine linear and interaction effects of the design factors on rate constants from Arrhenius correlations.

Jan 1, 1993

By J. B. Pateiro Fernandez, S. Möllerherm, E. Drüppel

"Since 1997 the Institute of Mining Engineering 1 at the Aachen University is dealing with the concept of sustainable development in the mineral industries. During this time it has conducted several research projects in this field. Its latest project is on the development of sustainability indicators for the German mineral industry. This paper describes some results of this project. A process chain analyses have been carried out identifying economic, social and environmental effects of the minerals extraction. Thirty indicators reflecting the particular conditions in the mineral industry have been designed. One important challenge was the design of quantifiable indicators taking into account the life cycle of a mining operation as well as mineral beneficiation and enrichment of the raw material."

Jan 1, 2005

By H. C. George

IN 1901, the United States produced 69 million barrels of crude oil, which was 41.4 per cent of the world production. By 1931, these figures were 850 million barrels and 62.1 per cent respectively, showing over this period of thirty years an increase in the world production of 718 per cent. Over this same period, the increase in the demand for technically trained men in the industry was much greater than the increase in crude-oil production. This was because much of the increase in production was secured by the application of geology and physics to the finding of new oil fields and by .the development of engineering methods and equipment incident to drilling and producing from much greater .depths.

Jan 1, 1934

Development of Technology for Complex Uranium Ores Processing on the Flotation Process Basis

Sep 13, 2010

By N. P. Titkov

This paper presents the results of laboratory and pilot plant investigations for the development of efficient methods of beneficiating hematite ores from the Krivoi Rog, Kursk Magnetic Anomoly, Olenogorsk, and other localities. The tests included gravity, magnetic (in a high intensity field), flota¬tion, and magnetizing roasting methods. It was possible to develop efficient beneficiation methods depending on the mineral composition of the ore and degree of dissemination of ore and gangue minerals. The paper shows the relationship between the iron silicate and quartz content of the ore and the technologic indices of the various beneficiation methods. Some of the conclusions based on these investigations and the technical and economic computations related to the cost of one ton of pig iron produced from concentrates obtained by the various beneficiation methods are: 1. If the hematite ore is not disseminated uniformly, it is expedient to use a combined gravity and flotation process. Ore particles up to 50 am. in size are beneficiated by gravity (heavy suspension, jigging, and others) and yield a lump concentrate. The middlings from this process are recrushed and floated; 2. Finely disseminated hematite ores, containing small quantities (less than 5 percent) of iron silicates, are most effectively beneficiated by flotation. Anionic (sulphate soap, tall oil emulsion with various foam depressors) as well as cationic collectors may be used. Depending on the mineral and chemical composition of the ore, it is possible to obtain concentrates containing up to 65 percent iron with an extraction up to 94 percent; 3. Finely disseminated, mixed hematite-magnetite ores may be beneficiated by flotation or a magnetic separation-flotation process; 4. Finely disseminated hematite ores, containing large quantities of iron silicates and earthy hematite ores are most efficiently beneficiated by the magnetizing roasting method. This method will yield concentrates containing up to 68 percent iron with extractions up to 90 percent. Although beneficiation by the magnetizing roasting process is costly, it will nonetheless, when employed on this type of ore, yield the least expensive pig iron.

Jan 1, 1960

Located 350 km west of Sydney and 20 km outside Orange, NSW, lies the Ridgeway Gold Mine û NewcrestÆs flagship Underground Gold Mine. Key to success at Ridgeway has been the fast tracked development of the 3.8 km, 1 in 5.3 conveyor decline which houses the 850 t/hr conveying system feeding the dedicated Ridgeway Concentrator, built adjacent to the existing Cadia Hill Concentrator. Eroc was contracted to develop the steep conveyor decline, drawing on its personnel and experience from past metalliferous, tunnelling and coal mining projects to complete the ambitious schedule within 12 months. This paper deals with the complexities and experiences in safely delivering what is understood to be one of AustraliaÆs steepest declines of any substantial length in a metalliferous mine.

Jan 1, 2002

By WenFeng Li

A 3D roof bolt model with the consideration of rebar, resin, bearing plate, and resin/rock interface was developed for studying the bolt/rock interactions of the tensioned and fully-grouted resin bolts. For the tensioned bolts, 2 ft compressive zone above the rooflineis generated by the 10 tons pretension. Since the free portion of the tensioned bolts displays a higher vertical stress, the increase of the bearing capacity of the rocks in such range is much larger. For the fully grouted resin bolts, despite no pretension is generated during installation, the roof sag can indirectly generate a compressive zone near the roof line. In addition, the analysis on the differences in bolt/rock interactions when employing the tensioned or fully-grouted resin bolts indicates that the fully-grouted resin bolts are preferred as the primary support when weak and thinly-bedded immediate-roof is present. Meanwhile, it is found that both the tensioned and fully-grouted resin bolts may have very limited effect in preventing and/or control the cutter roof.

Jan 1, 2014

The ore mined from the Lead Lode of The Zinc Corporation leases consists of a fairly granular mixture of galena, marmatite, chalcopyrite, tetrahedrite, pyrrhotite, pyrite, and lollingite with a gangue association of calcite, quartz, bustamite, rhodonite, mangan-hedenbergite, garnet, fluorite, mangano-calcite and apatite. The silver content of the ore occurs in three minerals tetrahedrite, dyscrasite, and pyrargyrite, the last two mentioned occurring in microscopic association only. Other metallic and gangue minerals are also present in this complex mineralogical association, but do not influence the milling operations.Fortunately, the silver minerals favour the galena and chalcopyrite as their host minerals, thus facilitating the recovery of both copper and silver in the lead concentrate. The ore from the Lead Lode assays from 14 - 18 per cent lead; 3.0 - 4.5 oz silver per tonne, and 9.5 - 12.0 per cent zinc.A parallel lode, known as the Zinc Lode, is well developed in The Zinc Corporation leases. This lode assays from six to eight per cent lead, 1.5 oz silver per ton, 18 - 25 per cent zinc with a siliceous gangue. The common Lead Lode gangue minerals, calcite, rhodonite, bustamite - are very rare in present underground exposures. No metallurgical work was done on this ore during the pilot plant operations.The aim in the milling process is to produce:1. A lead concentrate with the maximum economic recovery of lead, silver, gold, copper and antimony, and minimum zinc content.2. A zinc concentrate with the maximum economic recovery of zinc, cadmium, and cobalt, and minimum iron, arsenic and fluorine content.3. A waste residue containing sufftcient granular material to be utilised as underground fill.In considering the economics of the milling practice the above three requirements plus consideration of the tariffs submitted by the purchasers of concentrates were the deciding factors in the evolution of the present milling practice.Towards the end of 1924 The Zinc Corporation Limited added to and adapted the old zinc tailings plant for the treatment of 5000 tons of crude ore per week. This plant, which operated until January 1936, was in general principles similar to the standard Broken Hill methods of ore concentration, whereby the galena was recovered by the gravity concentration methods of jigging and tabling with selective flotation concentration of the residual galena and marmatite. One important difference from other Broken Hill plants was that the primary grinding of the jig tailing was performed with flint-loaded mills operating in closed circuit with revolving screens. Two primary grinding sections were installed, each consisting of two 5 ft diameter by 10ft long tube mills loaded with flint pebbles working in closed circuit with four 3 ft diameter by 3 ft wide revolving screens covered with 22mesh Toncap woven wire screen with 0.57 mm opening. Each section carried a circulating load of 28.3 tons per hour for a jig.

Jan 1, 1994

The ore milled from the Lead Lode of The Zinc Corporation leases consists of a fairly granular mixture of galena, marmatite, chalcopyrite, tetrahedrite, pyrrhotite, pyrite, and lollingite with a gangue association of calcite, quartz, bustamite, rhodonite, mangan-hedenbergite, garnet, fluorite, mangal1o-calcite and apatite. The silver content of the ore occurs in three minerals-tetrahedrite, dyscrasite, and pyrargyrite, the last two mentioned occurring in microscopic association only. Other metallic and gangue minerals are also present in this complex mineralogical association, but do not influence the milling operations. Fortunately, the silver minerals favour the galena and chalcopyrite as their host minerals, thus facilitating the recovery of both copper and silver in the lead concentrate. The ore from the Lead Lode assays from 14-18% lead; 3·0-4·5 oz. silver per ton, and 9·5-12·0% zinc.A parallel lode, known as the Zinc Lode, is well developed in The Zinc Corporation leases. This lode assays from 6-8% lead, 1·5 oz. silver per ton, 18-25% zinc with a siliceous gangue. The common Lead Lode gangue minerals-ealcite, rhodonite, bustamite-are very rare in present underground exposures. No metallurgical work was done on this ore during the pilot plant operations.The aim in the milling process is to produce: 1. A lead concentrate with the maximum economic recovery of lead, silver, gold, copper and antimony, and minimum zinc content.2. A zinc conc,entrate with the maximum economic recovery of zinc, cadmium, and cobalt, and minimum iron, arsenic and fluorine content.3. A waste residue containing sufficient granular material to be utilized as underground fill.In considering the economics of the milling practice the above three requirements plus consideration of the tariffs submitted by the purchasers of concentrates were the deciding factors in the evolution of the present milling practice.Towards the end of 1924 The Zinc Corporation Limited added to and adapted the old zinc tailings plant for the treatment of 5,000 tons of crude ore per week. This plant, which operated until January, 1936, was in general principles similar to the standard Broken Hill methods of ore concentration, whereby the galena was recovered by the gravity concentration methods of Hgging and tabling with selective flotation concentration of the residual galena and marmatite. One important difference from other Broken Hill plants was that the primary grinding of the jig tailing was performed with flint-loaded mills operating in closed circuit with revolving screens. Two primary grinding sections were installed, each...

Jan 1, 1941

By W. J. D. Stone

Discussions with people knowledgeable in the insulating material field revealed that materials on the market would be considerably improved if there was a greater meeting of certain very desirable criteria. Such criteria include: (1) the material should not burn, even at higher temperatures; (2) at an elevated temperature, the material should not give off toxic gases or produce smoke; (3) the material should have a low energy input; and (4) vermin would find the material unattractive. Theoretical discussions led to the conclusion that an insulating material made by foaming a mineral, preferably of a platy nature, with an inorganic binding system that could be converted to a rigid structure at low temperature would likely meet all the above requirements. It was also theorized that the use of microwaves in the converting stage would be beneficial in the creation of a cellular structure by aiding the foamer through creating vacules of steam. Talc was selected as readily meeting the theoretical mineral requirement and the material of Baker Talc Limited was used as the basic filler. The early results obtained led to an agreement between Americ Mines Limited and Baker Talc Limited pertaining to commercial production in a specific geographic area. It was recognized that due to the economics of shipping, the availability of the basic filler material should be geographically widely spread. Samples of materials were requested and many received from all over North America and one from Britain. Enough work has been done to show that they respond to the basic process in a similar manner as the Baker Talc material. From the data acquired, it is considered that the process is applicable for the production of loose fill insulation, moulded insulation for pipes and structural steel, ceiling tile, batts, sheet and for incorporation into other products such as various roofing board materials. Sufficient development has been done to enable a budget to be prepared for the construction and operation of a loose fill insulation plant.

Jan 1, 1979

By Royston, Woods R

ANI Bradken Vortex Pulp Lifters and Grates, both as original equipment and retrofitted to existing SAG mills, are now in field operation. The development of the Vortex leading curve pulp lifter was based on an analysis of traditional radia

Jan 1, 1997

Peko Mines, a Division of Peko-Wallsend Operations Limited (PWOL) has operated several small underground mines in the Tennant Creek district of the Northern Territory supplying ore to a central treatment plant. The Argo Mine is the most recently developed by Peko Mines. A magnetic anomaly was identified from low level airborne magnetics in 1960 and drilling, which commenced on the site in 1969, was halted in 1974 and resumed in 1980 following the rise in the price of gold. By mid 1983 a resource of + 200 000 tonnes of 12 g/tonne Au had been outlined and a decision to develop the resource was taken following the drilling of three further diamond drill holes which did not significantly alter the value of the resource. The small size of the orebody could not support the full capital cost of two shafts and a single entry mine plan was developed to extract the ore at a rate of 15 000 tonnes per month and to provide all the safety features, ventilation systems and services of a two shaft mine. In December 1983 a contract was let to Allied Constructions Pty. Limited (Allied) to sink and equip a 4.8m shaft to a depth of 410m and to convert the headframe and winder, which are leased for the life of the mine by PWOL from Allied, from a sinking to a production configuration. Shaft equipment designed by Hardcastle & Richards Pty. Ltd. (H & R) in conjunction with PWOL includes a skip/cage, counter- weight, and an auxiliary cage on rope guides, a sealed ladderway and exhaust air ducts.

Jan 1, 1986

By Max W. Ball

THE world's largest known oil deposit lies in northern Alberta. In fact, according to government estimates, the famous so-called 'tar sands' of the Athabaska region contain several times as much oil as all the other proved reserves of the world. S. C. Ells, of the Department of Mines and Resources, who has been the Dominion Government's authority on the oil sands since 1913, has estimated the minimum content of the deposits at 100 billion barrels(!). C. P. Bowie, of the U.S. Bureau of Mines, has published an estimate of 250 billion barrels(2). ?In comparison, the latest authoritative estimate of the proved oil-field reserves of the world is less than 35 billion barrels(3). Out of this tremendous total, perhaps 500 million barrels are commercially available at present-day costs and prices; the remainder must be considered a latent reserve to be used when development costs are materially lower and petroleum prices materially higher than they now are. Mean-while, the 500-million-barrel portion presently available contains more oil than has been found in all the rest of Canada, and constitutes one of Canada's great mineral resources. Although these deposits have been known to white men since 1788, when Peter Pond, the explorer, found the Indians stewing the oil out of the sand and mixing it with spruce pitch to caulk their canoes, they are only now coming into commercial production. The purpose of the present paper is to describe the deposits, their oil content, their present development, and the possibilities that seem to lie immediately ahead. For the sake of completeness and clarity, the writer has not hesitated to use or to paraphrase material that he has previously published elsewhere in discussing various aspects of the oil sands.

Jan 1, 1941

By R. England

"This paper describes the objectives and design parameters for the operation of a computerized In-The-Hole (I. T.H.) Drill. The principal objective is to add computer control to an Inco 00-60 I. T.H. (CMS-CD-90) drill in order to drill holes with greater accuracy. The computer provides control of the angle of the hole by maintaining the orientation of the drill head, and optimizes the straightness of the hole by maintaining a constant force on the drill bit.The second objective is to provide the greatest degree of operational automation, so the objective outlined above can be accomplished with a minimum of operator intervention.In order to provide full operational automation it was necessary to also provide the capability for the computer to add and remove drill rods. To accomplish this, a rod-handling mechanism consisting of a rod storage rack and rod manipulator arms was used.IntroductionMining machinery that lacks automatic control has been found to show a high degree of variation in work output and performance quality when operated by different personnel. Differences in operator attitude, judgment, and skill are reflected directly by production statistics. The addition of automated control has the potential for considerable improvement in machine life and performance. Even with a more acceptable mine environment and much safer conditions than ever before, situations still exist where it is preferable to remove personnel for reasons of safety as well as productivity. Typical advantages of such situations are automated skip loading and hoisting, and the use of remote control load-haul-dump units exposed to open stopes.Other cases arise where heavy work is required under conditions where lighting is poor, floors are slippery, noise levels are high and dust and oil mist exist in the atmosphere. I.T.H. drilling is carried out under such conditions and is one operation where automation can easily be justified."

Jan 1, 1987