Search Documents

Jan 1, 2003

Jan 1, 1993

Jan 1, 1988

Jan 1, 2000

Jan 1, 1984

Jan 1, 1985

Jan 1, 1986

By Antonio A. Cristóvão, Alexandre Pinto

"Abstract Deep foundations of buildings using driven ductile iron micropiles TRIM solutions, leads to recognized advantages, from technical, schedule and economic points of view. High production rates together with the possibility of using conventional equipment, duly adapted, confer this solution a high versatility.The aim of this paper is to describe the main design criteria adopted for the foundations of the Church ""Nossa Senhora dos Navegantes"" building in Lisbon - Portugal. In addition, results of a full scale load test carried out at site are presented, confirming the adequacy of the solution to the geological and geotechnical scenario, which is characterized by the proximity of the Tagus River Basin as well as the presence of heterogeneous landfill material and alluvial layers of soft clay (muds).1. INTRODUCTION Located on the right bank of the Tagus River, in Lisbon, the new Church building of ""Nossa Senhora dos Navegantes"", patroness of fisherman and navigators, with three or four upper floors, is surrounded by a school and by new residential buildings.The Tagus River basin is known by its alluvial soft soils, achieving, in certain areas, more than 50m meters depth, challenging the construction of new facilities due to the significant unfavorable geotechnical conditions.With a modern an unusual architecture, allusive to the ships used by the Portuguese navigators, the building has a reinforced concrete structure, with one basement and three upper floors. A bell tower with about 40m high, emerging from the structure, marks the landscape with the presence of this religious building (figure 2).For all the reasons previously described, geotechnical engineers play a crucial role on the design of valid foundation solutions, from both technical and economic point of view. Ideally, the solutions adopted should be supported by full scale load tests, performed at site, so that design assumptions could be verified and adjusted on time."

Jan 1, 2014

By Michael W. Oakland

Deer Island is the site of the Massachusetts Water Resources Authority (MWRA) wastewater treatment plant which, when completed in 1999, will serve 43 cities and towns in central eastern Massachusetts. Deer Island is located in the Boston Harbor, as shown on Figure 1. The existing wastewater treatment plant on Deer Island is being upgraded to include secondary treatment to comply with Federal require­ments. The new treatment facilities will process an average of 455 million gallons of sewage per day; total capacity will be about one billion gallons per day. The new treatment facilities will cover virtually the entire island. [ ]

Jan 1, 1994

By D. M. Morrison

"The most important factor in Canadian mining is not the operating cost of current projects but the availability of capital for future projects. The future of mining at depth will be producing ore from the top of the orebody working downward with very effective, tightly controlled mining methods, i.e. either selective mining or bulk mining with well controlled dilution and fragmentation. The key characteristics of future mines will be smaller access excavations, more effective ground support, very precise blasting techniques and more efficient and reliable materials handling systems. Equipment will be smaller and designed for high efficiency and low maintenance, reducing both the capital and operating cost. This means there will be fewer scoops, more continuous mucking machines and conveyor belts, both lateral and vertical.Orepass failures have become accepted and the resultant redevelopment and retramming has become common. The capital investment in so-called permanent ore passes and crusher stations becomes questionable, particularly when crushers are only necessary for less than 10% of the ore going through the system. The best way to solve the chronic instability of ore passes is, as with all of the stability problems at depth, by reducing the excavation size rather than increasing ground support. Smaller access drifts would reduce the capital cost and increase the rate of development as well as reduce the amount of waste to be handled, reducing the ground support and the ventilation requirements. Large drifts and ore passes are essential only for the equipment needed to handle large pieces of ore and the productivity of scoops is very expensive when the requirements for ventilation and large access drifts are taken into account. The key issue is the fragmentation generated by primary blasting.The future of mining in Canada will depend on simple and robust technology geared to the environment in which it will have to operate. Its survival will depend on some-thing much more fundamental and difficult to accomplish than a technological advance — it will require a dramatic change in the way the mining process is managed, how work is organized, how effort is rewarded and how costs are measured — a complete change in mind-set."

Jan 1, 1996

By Mullens P

Recent advances in technology have allowed many of the problems of directional control of long diamond drill holes to be overcome. Three case histories are presented, from Cobar, Hilton North and Mount Isa Mine, in which careful hole design and the use of wedges and down-the-hole motors have allowed tight directional control of drilling. Substantial savings in time and cost were achieved in all three cases.

Jan 1, 1990

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit? The rocks are well-consolidated Gila conglomerate, quartz , monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Ransome.3 In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special, fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 3 1/4x4 1/4-in. tool joints; 8-in. bits, 2 3/4x 3 3/4-in. tool joints; 6-in. bits, 2 1/4 x3 l/4 -in. tool joints; 4-in. bits, 1 5/8 x2 5/8-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property, To allow for 2 3/8-in. drill pipe with tool joints, 3 1/2-in. core barrels and bits were used. With the standard 3 1/2-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 5 5/8 to 3 7/8 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven-machines. The open churn drill hole was cased with 2 1/2-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in unconsolidated material like the formations drilled by

Jan 1, 1952

By Albert Ruiz

The 2,250-MW, coal-fired Navajo Generating Station located in Page, AZ draws water from Lake Powell using submersible pumps installed in five inclined shafts. Drought threatens to lower the reservoir to below the existing intakes. A system of new steel-lined intake shafts located on the same site was required for uninterrupted plant operation. The small size of the site, and the need to keep the existing system in operation, required detailed designs and placed significant limitations on construction equipment and activities. The Navajo Sandstone that forms the near vertical shoreline of the reservoir is 98 percent very fine grained quartz, highly abrasive and contains highly fractured intervals that presented numerous challenges to drilling the new 152-m (500-ft) deep, 109-cm (43-in.) diameter intake shafts inclined 23° to 26° from vertical. Spatial constraints, submersible pump design and operational criteria required that each shaft have a unique inclination and orientation and hit a small breakout target located 76 m (250 ft) under water. Sophisticated drilling equipment and techniques as well as state of the practice downhole survey technology and methods were used to make adjustments and maintain drilling accuracy with less than 1 percent deviation. Environmental requirements mandated water as the drilling fluid and grout was not allowed in to the lake under any circumstances. The shafts were videotaped and the breakout locations were examined using an underwater remotely operated vehicle (ROV) to verify shaft locations and rock conditions, and to guide placement of pneumatic packers to ensure grout did not transmit to the lake during the steel liner installation. In anticipation of the invasion of quagga mussels, the shaft design included an allowance for a chemical dosing system and a copper-rich alloy at the exposed portions of the steel liner.

Jan 1, 2011

By Scott A. Walker, Roberto A. Lopez, Lori A. Simpson, David A. Shook

500 Folsom Street is part of the new Transbay neighborhood in San Francisco, which is being redeveloped after the 1989 Loma Prieta Earthquake damaged a freeway viaduct; removal of the viaduct created parcels of land available for development. The development consists of a 42-story residential tower with a six-level basement. The slender, core-only structure was designed using performance-based seismic design. Subsurface conditions include undocumented fill, Dune sand, marsh deposits, sand, and clay, all overlying sloping bedrock of the Franciscan Formation. The building is supported on a 10-foot-thick mat foundation approximately 62 to 72 feet below street grades; clay, sand, and bedrock are all present at mat subgrade. Under a portion of the mat, sand susceptible to liquefaction was present. The variable subgrade conditions and potential for ground failure, along with the depth of mat subgrade below street grade, created a challenge for the design and construction team to solve. The ground below mat subgrade needed to be improved to mitigate the liquefaction potential and provide more uniform support. The areal extent and depth of ground improvement necessary to support the mat with an acceptable amount of deformation was determined. Settlement was analyzed and subgrade moduli were provided for design of the mat, with multiple iterations performed to converge between the geotechnical and structural models. Based on the project schedule and logistics, it was beneficial to work from street grade to improve the ground. In order to target the depths below the mat and minimize wasted effort and materials within the depth of excavation, grids of jet grouting were determined to be the most economical ground improvement method; however, it was challenging to install the columns from 65 feet above the top of the target zone. During installation, QA/QC was performed to check that the jet-grouted columns were installed to the design depth and diameter and developed the design strength.

Jan 1, 2018

Structurally- controlled deep leaching processes have removed vast quantities of carbonate from a substantial portion of the "silica-dolomite" enclosing the 500 copper orebody. Mine drainage subsequently allowed free access of air to the porous environment created and oxidation of sulphides commenced. During the mIne development stage the exothermic and temperature-dependent nature of these hydrolysis reactions resulted in a slow general elevation of ground temperatures. and levels of 90 - lOO°C were attained in restricted moist sulphide-rich areas.With the advent of production and extensive use of explosives, the oxidation processes were locally raised to new levels of activity. Direct interaction of explosives and sulphides in favourable conditions caused temperature rises to above 260 C. Above this point the dry oxidation of sulphides in air was initiated and rapid escalation to the vicinity of 800 C has been known to occur in isolated cases.Ground reactivity is a function of the complex interrelationship of several controlling factors and no simple index exists.Control techniques are presently aimed at prevention of temperature rises in the range 100 -260 C. Inhibition of the rapid dry oxidation processes above 260 C is difllcult and current efforts have met with only partial success.

Jan 1, 1968

By McCarthy P. L

A distinctive feature of the goldfields of Victoria was the extrac- tion of gold from deep leads, that is the buried river beds of Vic- toria's ancient rivers and streams. It is estimated that about 265,000 kg of gold was produced from Victoria's deep lead mines which comprises about 11.5% of Victoria's total production of gold (Bowen, 1974). The significance of deep lead mining for Victoria, however, went far beyond its economic contribution to Victoria. If Profes- sor Blainey is correct it was the frustrations of mining gold from deep alluvial leads in Ballarat during 1854 which precipitated the Eureka Stockade (Blainey, 1963, 46-52). This event resulted in the implementation of a fair mining administration and was an emphatic statement of the rise of democratic movements in Australia. Much of the technology and skill for mining deep leads had to be developed locally because at that time no other major gold- field elsewhere in Australia or the world had gold deposits with comparable problems. Deep lead mining in Victoria was there- fore largely a home grown industry and the equipment for that industry was often designed and produced in Victoria.

Jan 1, 1988

By A. Pareek, V. S. Masampally, V. Runkana

Mineral processing plants, in general, consist of comminution and separation circuits. Rougher flotation is considered as the heart of the separation circuit with concentrate grade and mineral recovery being the key productivity and quality parameters that affect the downstream operations and profitability. Online prediction of these parameters can help improve process performance in real-time. Past efforts to predict flotation cell performance have focused on building physics-based or machinelearning (ML) based models. Although physics-based models are popular in process design applications, ML models are more appropriate for online monitoring, control and optimisation due to their lower computational requirements. Deep learning (DL) is gaining prominence nowadays for application in industrial operations where a large amount of data is available. We have developed a DL model based on long short-term memory (LSTM) neural networks to forecast the two key performance indicators (KPIs), namely, mineral recovery and concentrate grade in a mineral processing plant. Rougher feed characteristics such as mineral grade and particle size distribution, upstream measurable disturbances such as throughput of the comminution circuit and pulp density, and control variables such as aeration rate, pH, and collector addition rate are considered as explanatory variables to train the model. The model was tested with data from an industrial mineral processing plant. For real-time dynamic predictions, the trained model appropriately accounts for mismatch in measurement frequency of real-time process data and off-line laboratory analysis data. Such a time series model can be used as a state observer in model predictive control techniques for optimal control of unit operations in a mineral processing plant. Keywords: Mineral processing, flotation, time-series, dynamic modelling, deep learning

Jan 1, 2020

By Bastiawarman Rifki, Nugraha Nico, Priatna Anton

The Deep Mill Level Zone (DMLZ) is one of the underground mines operated by PT Freeport Indonesia (PTFI). DMLZ is located approximately 1,500 m below ground level, where dominant rock types are skarn and diorite. The DMLZ mine and layout was designed based on the previous mine located above ground, the Deep Ore Zone (DOZ). The DOZ mine, located approximately 1,000 m below ground level, was a proven success, with a maximum capacity of 80K tonnes per day. During the production ramp up, which started in 2015, the DMLZ experienced several seismic events. The most significant event occurred in January 2018 with a recorded magnitude of more than 2.0 Mw, which resulted in a 14-month delay of the undercutting until March 2019. The significant event in January 2018 required the DMLZ to apply several adjustments related to the mining plan to help ensure it could continue development and achieve production target safely. This paper will describe the changes in the DMLZ mine plan as a response to the seismic activity at the mine, the reason behind the decisions being made to change the mine plan and strategy, as well as strengths and weaknesses between the previous plan compared with the new plan.

Apr 26, 2022

By A Priatna, H Rumbino, T Casten

This paper discusses the progress of the Deep Mill Level Zone (DMLZ) mine from the pre-feasibility study completed in 2005, through commencement of development access in 2008, completion of the feasibility in 2010 and cave initiation in late 2015. This fourth lift of caving in the East Ertsberg Skarn System (EESS) is located 500 m below the currently producing Deep Ore Zone (DOZ) mine and represents approximately half a billion tonnes of ore and around 1900 planned drawpoints, scheduled to be mined at a peak of 80 000 t/d.The paper reviews the mine design, access requirements, planned footprint sequence and major fixed facility installations such as ventilation, oreflow and shops. A discussion of the preproduction development and construction activities and some of the critical technical challenges overcome during this time frame are addressed, as well as the cave initiation process undertaken in late 2015 and the ramp-up of production and progression of caving.CITATION:Casten, T, Priatna, A and Rumbino, H, 2016. Deep Mill Level Zone – from feasibility to production, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 635–644 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By The Staff

"IntroductionThe difficulties to be overcome in shaft sinking and development at depth are centred at McIntyre in and around No. 12 shaft. Generally they have been due to increasing pressures and temperatures and to changes in geological structure. This paper describes the difficulties and the measures taken to meet them.No. 12 ShaftEarly in 1932 McIntyre decided to sink an internal shaft from the deepest level, the 3875, to explore and develop known veins extending below that horizon. The location selected was a point 1,500 feet south and 1,000 feet east of No. 11 shaft, the main operating shaft through which the men, ore, and most of the materials are handled Shaft and auxiliary equipment we1e laid out for 3,000 feet, that is to 7,000 feet below the surface. The shaft was to be capable of handling 1,500 tons of ore daily from the lowest level, and was to provide ventilation, compressed air, water, and electric power to service all levels.No. 12 is an internal, vertical shaft extending from the 3875 to the 6825 level and bottoming at 7,007 feet. It is a rectangular, four-compartment shaft, 21 ft. 9¾, in. by 6 ft. 3¾ in. outside the timber (Figure 1).There are two hoisting compartments and one airway compartment, each 4 ft. 10¾ in. by 5 ft. ¾ in. inside dimensions, and a combined manway, pipe, and cable compartment 4 ft. ¼ in. by 5 ft. ¾ in. Levels have been established at 150-foot intervals, pump stations and sumps at 1,000-foot intervals, and. there are two loading pockets, one at the 5525 and the other at the 6900 level.The shaft was sunk in two stages. The first stage, consisting of preparation above the 3875 level and sinking to 5585 feet, was completed by March 31st, 1935. The second stage of deepening the shaft from 5,585 to 7,007 feet was started August lst, 1946, and completed three years later."

Jan 1, 1950