Search Documents

By S. S. Klima, A. L. Mazzella, J. S. Driscoll, T. W. Beck

Previous testing was performed by researchers at the National Institute for Occupational Safety and Health (NIOSH) to improve longwall dust control using underside shield sprays with a longwall directional spray system. This testing provided encouraging results toward respirable dust exposure reductions for longwall personnel, achieving as high as 99% dust reduction at some sampling locations along the longwall personnel walkway. Additional laboratory testing was conducted to test these underside shield sprays in conjunction with a shearer-clearer spray system located on the longwall shearer body. The purpose of this testing was to determine if the underside shield sprays interacted positively or negatively with the shearerclearer sprays. Results from this testing indicate that while the shearerclearer system influences where the respirable dust particles are directed, underside shield sprays can still lower respirable dust exposure for longwall personnel.

Mar 2, 2022

By A. R. Laplante

A test to determine the amount of gravity recoverable gold (GRG) in an ore is described. Typical GRG results are given; an error analysis is detailed; possible uses are discussed. Of the 38 samples tested, the lowest GRG content was found to be 25% (most below 25 11m, or 600 mesh), and the highest 94% (most above 300 11m, or 50 mesh). The average GRG content was 63%, with a standard deviation of 19%. Error analysis shows the test to be reproducible within 5 to 10%, depending on the size distribution and grade of GRG, and the sample extraction protocol. When using the same primary sample, reproducibility improves, 2 to 5%, depending on the amount of gold coarser than 850 11m (20 mesh) and sample weight. The test has been applied to greenfield project and retrofit applications, to determine the suitability of gravity recovery. For existing circuits, it has been coupled with a model of gravity recovery for optimization studies.

Jan 1, 1996

By B. G. Cousins, B. O’Rourke, C. Spence

"Some non-flotation chemicals are added to flotation circuits directly and indirectly to control issues such as scaling and dust in other areas of the operations. Since dosage levels are generally not high, a standard laboratory float test may not be able to determine the effect of a specific chemical on the productivity of the flotation circuit. This paper presents a laboratory testing protocol that uses kinetic float studies to test the effect of normal to extreme doses of antiscalant and dust chemistries (5–100 g/t). Results indicate that this protocol helps to predict potential interference by a particular chemistry on the flotation circuit.RÉSUMÉ Certains produits chimiques ne servant pas à la flottation sont ajoutés directement et indirectement aux circuits de flottation afin de contrôler des problèmes tels que l’entartage et la poussière dans d’autres secteurs des opérations. Étant donné que les niveaux de dosage sont généralement faibles, un essai standard de flottation en laboratoire pourrait ne pas être en mesure de déterminer l’effet d’un produit chimique spécifique sur la productivité du circuit de flottation. Le présent article définit une procédure d’essai en laboratoire qui utilise des études cinétiques de flottation pour vérifier l’effet de doses normales à extrêmes de produits chimiques antitartre et anti-poussière (5 à 100 g/t). Les résultats indiquent que ce protocole aide à prédire l’interférence potentielle d’un produit chimique particulier sur le circuit de flottation."

Jan 1, 2016

By B. G. Cousins, B. O’Rourke, C. Spence

"Some non-flotation chemistries are added to flotation circuits directly and indirectly to control issues such as scaling and dust. Since the dosage levels are generally not very large, a standard laboratory float test may not be able to determine the effect a specific chemical has on the productivity of the flotation circuit. Hudbay and Ashland Water Technologies developed a laboratory testing protocol that uses kinetic float studies to test the effect of normal to extreme doses of antiscalant and dust chemistries (5 ppm to 500 ppm). Laboratory results indicate that this protocol helps to predict the potential interference that a particular chemistry will have on the flotation circuit.INTRODUCTIONFrom a chemical perspective, flotation is a very complex system involving more than the reagents used for flotation. Along with collectors, frothers, modifiers, suppressants and activators, there can be antiscalants for water treatment, dust suppressants used in the mining process, residual flocculants from recycled thickener overflows, grinding aids, and many other types of chemicals that are added upstream of a flotation circuit. Although these other chemicals are usually used at very low doses, it is important to know if they affect the flotation process detrimentally in the event of a spill or a build up from recycled water.Laboratory flotation testing of these chemicals characterizes their effects, but testing at expected doses in the float can mask the effects of the chemicals in the plant. Also, simple tests that do not measure the kinetics of flotation do not reveal the effects the other chemicals have on the flotation circuit. Thus, a new flotation protocol was needed to expose the full effects of chemical additives and to assist in choosing the chemical with the lowest potential for a negative effect.FLOTATION KINETICSMeasuring recovery kinetics in a laboratory flotation cell is a well-established procedure: analyzing concentrates taken in a timed sequence to determine the recovery rate of individual cells in a flotation circuit. The recovery from the early flotation cells are a true measurement of how well a flotation chemical is performing. The principles of kinetics can be mathematically determined by the following functions (Houston, 2006):"

Jan 1, 2013

By C. E. Seaman, H. Jiang, S. Klima, T. W. Beck, Y. Zheng

Respirable coal dust has been long recognized as a leading cause of multiple lung diseases. Efforts aimed at reducing dust concentration in underground mines have been made, but increases in coal workers’ pneumoconiosis incidence rates over the last 20 years among U.S. miners are concerning. Dust deposition and water spray suppression are two types of dust removal mechanisms in underground mining activities. In this study, laboratory tests were conducted to investigate the respirable dust decay characteristics during deposition and suppression processes in a confined dust chamber. Dust concentration and size distribution were monitored continuously throughout each 60-minute test. A number-basis particle size distribution was used for analysis to capture the changes of smaller size fractions within the investigated dust sample. This study found that around 62.1% of respirable dust particles were deposited at the end of the deposition test. In addition, the final deposition rate for very fine particles can be less than 20%. The results from the suppression test indicate that larger particles were removed quickly; however, sub-micron particles remain suspended through the 60- minute water spray, and particles under 0.5 µm can be considered irremovable dust under single-spray operation conditions. This study also observed the resuspension of a significant amount of sub-micron particles by the water spray. The results of this study provide basic information for improving dust control strategies and can be utilized to improve the water spray performance for reducing airborne dust levels.

Mar 2, 2022

Laboratory induced polarization measurements were made on representative samples of concentrated sulphide ores from three environments in New South Wales Comparisons were made with the membrane polarization exhibited by an argillaceous sandstone. The sulphide samples showed a strong polarization effect, the magmtude of whIch depended directly on the conductivity of tlIe pore electrolyte.

Jan 1, 1969

Sinter mixes of three iron ore types were prepared with a range of water contents in a laboratory investigation. The mean diameter of the granulated mixes and the void fraction of beds of the mixes were determined experimentally. Pressure drop measurements over a range of flow rates were made in a laboratory permeameter with pressure tappings at several depths in the bed. The Ergun equation was applied to the results to determine the shape factor of the granulated mixes. The pressure readings down the bed were used to estimate the local void fraction in the bed using the Ergun equation and the calculated granule shape factors and it was found that there was a decrease in void fraction with depth in the bed. The significance of this and the variation of the shape factor values with the amount of water used for granulation is discussed in relation to the strength of granules of the sinter mixes.

Jan 1, 1984

By Eung Ha Cho, Olufemi Olajide

A laboratory study of dense-medium cycloning with Redstone seam coal has been conducted. The investigation was performed using a 203 mm (8 inch) Heyl-Patterson dense-medium cyclone. Two underflow orifices of 31.8 mm (1.25 inch) and 44.5 mm (1.75 inch) in diam were used. The effects of feed pressure and particle size were determined on the cycloning performance. In addition, the cyclone performances with coal-rich and refuse-rich samples were also investigated. The results of the experiments were analyzed using basic hydrodynamic principles. The increase in the feed pressure increases the specific gravity of separation (defined as the specific gravity of a particle which has an equal chance of reporting to either the overflow or underfow) for both underfow orifices. The specific gravity of separation increases as the particle size decreases with the smaller underflow orifice. However, an opposite relationship has been observed with the larger under flow orifice. The separation becomes sharper with the smaller under flow orifice than with the larger underflow orifice especially for fine material. Also, the separation becomes sharper with an increased feed pressure for a coal-rich sample. However, this effect is less significant for a refuse-rich sample. This means that a high feed pressure is required for a coal-rich sample to maintain a good separation. It also means that applying a high feed pressure provides a good separation regardless of the type of feed coal in terms of ash content in the solid.

Jan 1, 1990

By B. Anameric, S. K. Kawatra

Pig iron nuggets were produced in a laboratory scale furnace at Michigan Technological University. These nuggets are produced from pellets consisting of a mixture of iron oxide, coal, flux, and a binder, which are heated to 1450°C.These pellets then self-reduce to produce a solid, high-density, highly metallized (96.5% Fe) pig iron. During the nugget production process, a separate slag phase forms that cleanly separates from the metal. The physical and chemical properties of the pig iron nuggets are similar to pig iron produced by blast furnaces, which is distinct from Direct Reduced Iron (DRI).

Jan 1, 2004

By W. R. Lindsay

Considerable attention has of late been given to the blasting of large amounts of ore in one operation, on account of the saving in labour and explosives and consequent low cost per ton, and also on account of the additional safety to employees. The blast here described, at the Hidden Creek mine. at Anyox, B.C., is not necessarily unique either in size or methods employed, but some interesting p10blems were encountered and the solutions of these may be of interest to others engaged in similar work. The ore consisted mainly of old scope-bottoms and sill pillars, although there also were some braces and parts of vertical pillars included. Some of the stope-bottoms were overlain by caved waste, and one of the problems was to break them in such a manner that the maximum amount of ore could be recovered without serious dilution with waste. The ore blocks, designated as the 385 silt and the 7 A-103 blocks, were under preparation for blasting for over a year, as conditions permitted. This work consisted in drilling long machine drill holes, varying in length from 14 to 20 feet. These holes were drilled with the Numa detachable bit, made locally, starting at 2~-inch diameter and bottoming at 2 inches for the longest length. The long hole drilling was used in the thinner sections of the area. For the stronger, thicker portions, powder drifts (3 ft. by 4 ft. in section) were driven for the powder charges. Reference to the plan and sections (Figures 2 co 8 inclusive) show the relative location of these, as well as the long drilling. The amount of explosives used in the powder drift charges averaged 0.25 pounds per ton of estimated burden, varying from 0.2 to 0.3 pounds per ton.

Jan 1, 1934

By K. V. Raj

As open pit mines continues to grow deeper, managing air pollution can become challenging. During arctic air inversion, the temperature of the air over the mine increases with altitude, and the cold, heavy, surface air is trapped in the pit. This problem is complex, and any solution will require an extensive understanding of the interactions between the aerodynamic movement of air, air inversion, meteorology, pollutant sources, and transport phenomena in the open pit mines. The availability of computational fluid dynamics (CFD) has elucidated the pollutant flow mechanism in open pit mines. Very few CFD studies have been published, especially the Large Eddy Simulation (LES), on the contaminant transport in deep open pit mines under arctic air inversion. The contaminant transport in an open pit mine under arctic inversion is due to a stable or nocturnal boundary layer in micro-meteorological terms. Understanding the physics of the stable boundary layer (SBL) is relevant to air flow and pollutant transport in deep open pit mines. This paper focuses on a Large Eddy Simulation (WMLES as Sub-Grid Scale Model) modeling of the SBL and pollutant transport in a large open pit mine.

Feb 23, 2014

By R. M. Porter

PILLAR extraction at the Sullivan Mine bas been in progress for over twenty-five years and bas .involved progressively larger pillars. The largest pillar blasted to date exceeds one million tons and is described in this paper. This blast is believed to be one of the largest to take place entirely under-ground. The Sullivan Mine, owned by The Consolidated Mining and Smelting Company of Canada Limited, is located in the southeastern corner of British Columbia on the east flank of the Purcell range overlooking the twenty-mile wide Rocky Mountain Trench (Figure 1). The orebody is a bedded replacement deposit in argillites, varying in thickness up to 300 feet, but averaging about 80 feet. Above the 3900 Level, the dip varies from nearly horizontal to 40 degrees; be-low the 3900 Level it varies from 45 to 20 degrees (Figure 2). Pillar extraction follows a plan of retreating outward from caved areas. The size of each blast is determined by the effect which the removal of support

Jan 1, 1961

By Tadeusz Cyrul

Results of a large scale compression test in situ are the subject of discussion. A cube of coal having an edge length of 1.5 meters was subjected to uniaxial compression tests in situ. At the same time both load and deformation were controlled. Deformations were measured on 60 short measurement bases, each 23 cm in length. The bases were uniformly distributed on the side surface of the cube, forming five horizontal rows and twelve columns on the development of the surface. Readings were taken from each gauge for each level of loading which was increased step by step. Due to heterogeneity of the rock, readings showed scatter. Scattered data were approximated by a plane, using the least squares method for each row separately and for the entire population of bases. Orientation of the planes are analyzed. The geometrical measure of the bending moment is introduced. It shows that the magnitude of the bending moment and the bending plane differed from row to row, thus implying that the cube was not only bent but twisted as well. This complex behaviour of the coal cube is apparently caused by its heterogeneity and vertical anisotropy. The results constitute a contribution to the verification of existing design criteria on the stability of mining pillars.

Jan 1, 1984

By A Smith

Rock masses usually exhibit scale dependent mechanical properties primarily due to presence of discontinuities and their inhomogeneous nature. One of the essential preconditions for selection of appropriate strength and deformation parameters of a rock mass in relation to tunnel design is assessment of the scale of the joint network relative to the scale of excavation. In tunnel design practice, scale effects are estimated indirectly using small-scale unconfined compressive strength (UCS) tests and rock mass classification based empirical correlations. Large-scale UCS tests have the benefit of direct assessment of anisotropic and scale dependent properties of a rock mass.This paper presents results of a large-scale UCS test on a jointed siltstone. A 450 mm diameter sample with inclined bedding planes was cored and tested in uniaxial compression until failure with load and displacement measurements. The aim of the test is to determine strength and deformation parameters and correlate them with results of small-scale UCS tests of the same sample. The relationships between the small-scale and large-scale rock mass parameters were validated against published correlations from the literature.

Mar 8, 2011

By Hayward N, Sutherland D, Wilkie G

A pilot plant study has been made of the liberation characteristics of a nickel ore under different milling conditions. A series of runs were made ranging from fully autogenous grinding to semi-autogenous grinding with a ball load of 8%. The mill products were sized and assayed then analysed by QEM4SEM. This enabled a full liberation analysis to be carried out to see whether the autogenous grinding leads to improved liberation by promoting selective breakage. Though it is frequently claimed that fully autogenous grinding yields superior liberation this could not be detected in the present study.

Jan 1, 1991

By Christina Viklund-White

Life Cycle Assessment has been used to compare the environmental performance of landfilling versus recycling of the zinc used for galvanizing steel. Hypothetical process routes were com-posed involving four different EAF dust treatment processes; Waelz kiln, DC-furnace, EZINEX and slag fuming, as well as scrap dezincing. The study shows that recycling of zinc used for galvanizing steel has environmental benefits in that it saves zinc resources. However, zinc recovery does not necessarily decrease the potential impact on global warming and acidification. The magnitude of these two impact categories is tightly correlated with the amount and type of primary energy consumed in a process. Due to the high electricity consumption in the dezincing process, this route has the highest impact on Global Warming Potential as well as Acidification Potential. The major part of the energy requirement for the production of zinc from primary and secondary sources is consumed in the reduction of ZnO to Zn. The consequence is that the theoretically possible savings in primary energy by recycling zinc-containing materials are relatively minor. The impact categories "land use" and "waste generation" are not considered in this study, but most likely the evaluation of such impacts would further increase the potential environmental impact of the landfill alternative. The results also show that the location of an electricity-intensive process highly affects the potential environmental impact. Comparing process and material alternatives in LCA studies where branch average data is used, is considerably more complex than when LCA is used within a company.

Jan 1, 2000

The coal-based power generation industry faces increased pressure from all sectors to improve its environmental performance. This is due to increased awareness of and concerns regarding greenhouse-and acid-gas emissions, toxic metal releases (to both air and water) and water availability. A methodology to assess this industry?s environmental performance is needed. Such a methodology should assess all environmental impacts accurately, recognizing the irspatial and temporal dependence, and taking into account the social acceptability of technologies employed. Here, we develop a methodology to determine the environ-mental impact associated with solid wastes generated by this industry, and apply this to the specific case of ash management. More specifically, the case study compares the environmental footprint of an ash deposit for a number of operational water management scenarios. The methodology considers leachate generation processes from ash impoundments to obtain a time-dependent concentration profile of mobile constituents at the interface between the ash impoundment and the surrounding environment. This leachate prediction modelling is subsequently linked to plume dispersion modelling tools to determine the fate and transport of leached components, predominantly salts, into groundwater. Together, these provide a measure of the extent to which a land mass is affected by leachate migration from the deposit. To determine the exact boundary between regions of acceptable and unacceptable risk to the environment, we use Ecological Risk Assessment concepts. In this way it is possible to obtain a time dependent affected land footprint which could be used as an indicator of the environmental impact of solid waste management practices. This information can be included in a set of environmental criteria which form the basis of an overall environ-mental impact assessment, using tools such as Life Cycle Assessment (LCA). The value of LCA is that its structure is consistent with accepted models of environmental decision making, where different approaches to valuation in impact assessment assist in prioritizing impacts on the basis of their perceived significance. The proposed ?affected land footprint? metric represents a significant improvement over current LCA impact indicators for solid waste management practices. Keywords: Environmental Impact Assessment, Environmental Risk Assessment; Life Cycle Assessment; coal ash; leachability; salinity

Jan 1, 2002

By R. C. Milici

Historical production data and reserve decline rates can be used both to predict future coal production rates and to estimate when the reserve will be depleted. Reserve estimates inferred herein from historical production data and decline rates are commonly lower than estimates made from geologic data. The latter include significant amounts of lower quality (deeper, thinner, higher sub) coal which may be mined when the better deposits are depleted.

Feb 24, 1997

By R. C. Milici

Historical production data and reserve decline rates can be used both to predict future coal production rates and to estimate when the reserve will be depleted. Reserve estimates inferred herein from historical production data and decline rates are commonly lower than estimates made from geologic data. The latter include significant amounts of lower quality (deeper, thinner, higher sulfur) coal which may be mined when the better deposits are depleted.

Jan 1, 1997

By James Ball

The paper describes a new type of pump and related apparatus specifically designed to dredge sea-floor minerals from very great depths. The principle of operation of the dredging system is explained, and the factors which determine the equipment size and the power required for varying mining rates and depths of water are discussed. An estimate of the capital and operating cost of a commercial-scale mining system is presented.

Jan 1, 1968