Search Documents

By John Newby, Mahmood Khwaja, Bernard Theron, Janice McGovern, Bernard Catalano, Michael S. Schultz

Launching a full-size pressurized-face Tunnel Boring Machine (TBM) in difficult ground conditions is always challenging. Recently, few projects have innovated the process by scaling the trenchless method of pipe jacking, and modified steel bell approach, to facilitate the launching of a full-size TBM without the need for large and deep trenches, starter/tail tunnels, or for incrementally installing supporting gear as the machine advances. This paper presents three such projects; evaluates the post-bid contractor proposed modifications; details the innovative use of pre-cast pipe segments to facilitate machine launch; and, provides an overall assessment of the benefits, challenges and lessons learned related to the modified approach.

Jun 13, 2021

By G. R. Lane

A large opencast gold mining company in Africa had just completed a feasibility study for an expansion of the operations. A traditional net present value project valuation methodology had been used that showed a very positive net present value (NPV). The project team had conducted a qualitative risk assessment that identified and logged all potential project risks and had subjectively incorporated 'risk' via the discount rate and other assumption contingencies around gold price expectations, operating parameters, etc. Management requested that an independent quantitative risk modelling approach be adopted to obtain a better understanding of the impact of risk on the overall project valuation and confidence level in the final valuation. A detailed project valuation model was configured in the Cyest Carbon Modelling Technology platform, and the stochastic modelling module used to perform the Monte Carlo simulations. Analysis of historical operational performance data relating to actual achievements versus planned and budget determined the historical variability of the underlying parameters as well as variance to budget. This was done at a detailed level for mining rates and costs, processing rate, costs and recovery, and other operational efficiency measures. External market assumptions relating to gold price, exchange rate, and inflation were modelled and the dependency between them modelled using a copula. This case study will demonstrate the approach taken to building and populating the quantitative risk model and the overall results of the Monte Carlo simulation. The final valuation demonstrated that the project had a 44 percent probability of an NPV less than zero i.e. a 44 percent chance of project finance loss.

Jan 1, 2013

By Stanko Nikolic

The Top Submerged Lance (TSL) technology, developed in the 1970s, is now widely used for the processing of a range of materials. TSL technology for continuous converting was first patented in the 1990s. The process is based on the use of calcium ferrite slag. Although this slag system had been applied elsewhere the phase equilibria had not been thoroughly investigated. This lead to a collaboration between the Process Technology group of Mount Isa Mines, now part of Glencore, and the Pyrometallurgy Innovation Centre (PYROSEARCH) at The University of Queensland. Through multiple research programs this complex system was successfully investigated. The results were then implemented within thermodynamic modelling tools. This combined new knowledge was then applied to the design and industrial implementation of the TSL continuous converting technology, ISACONVERT™. This paper describes the key findings of the research and how this was applied to the industrial implementation of the technology.

By Karl A. Higgins, Michael D. Venezia

The South Capitol Street Corridor Project is one of the District Department of Transportation’s (DDOT) largest projects, and is currently under construction. This case study will focus on the design of the foundation piles for the main spans of the iconic Frederick Douglass Memorial (FDM) Bridge, and will include a discussion of the foundation design evolution from an originally designed alternative foundation system (i.e. coffer dams and drilled shafts), to the current use of driven Large Diameter Open End Pipe (LDOEP) Piles. The paper will provide a discussion of the design methodology used during preliminary engineering and final design, and will highlight insight gained from the extensive load testing program completed to date. The load testing program consists of a combination of high strain dynamic testing (PDA), as well as Statnamic Load Testing on select sacrificial, pre-production test piles. Specifically, data gathered during the nearly-completed load testing program suggests the development of significant internal shaft frictional resistance within the tested LDOEP Piles. This paper will also discuss limitations of currently accepted industry design methods for predicting the capacity of LDOEP piles, a subject that is also currently being researched by FHWA. The data from this test pile program will help design assumptions for future projects. INTRODUCTION The Frederick Douglass Memorial (FDM) Bridge carries South Capitol Street across the Anacostia River in Southeast/Southwest, Washington, DC, and is owned and maintained by the District Department of Transportation (DDOT). The existing FDM Bridge is nearly 70 years old, serves as a major artery into the city, and has been classified as functionally obsolete. As a result of the condition, age and limitations of the existing bridge structure, DDOT deemed it necessary for complete replacement of the bridge. The replacement project consists of the construction of a new bridge traversing the Anacostia River, as well as the reconfiguration of the Suitland Parkway and I-295 interchanges located at the eastern terminus of the FDM Bridge. Final design and construction services for the replacement project were procured by DDOT through a Design-Build contract. This paper will focus on the driven Large Diameter Open End Pipe (LDOEP) Piles used for support of the main span of the new FDM Bridge which is currently under construction. Discussion regarding the LDOEP Pile design methodology has been included, along with commentary regarding currently available industry guidance related to design and construction of LDOEP Piles. Much insight has been gained during the mostly-completed and extensive load testing program which consists of a combination of high strain dynamic testing (PDA), as well as Statnamic Load Testing on select sacrificial, pre- production test piles. Specifically, data gathered during the mostly-completed load testing program suggests the development of significant internal shaft frictional resistance within the tested LDOEP Piles.

Jan 1, 2019

By N Currey, G W. Wilson, P Ritchie

Kidston Gold Mine in Queensland, Australia has a 310 ha tailings impoundment that has undergone final closure rehabilitation. Kidston Gold Mine evaluated their closure options for this low acid generating tailings impoundment, and due to a lack of cover soils and the cost of importing material, the mine decided to investigate the possibility of direct vegetation onto the tailings impoundment surface. The mine subsequently embarked upon a well planned and detailed research program to determine the feasibility and sustainability of this closure option. The research program included vegetation trials, toxicology studies for metal uptake by vegetation, as well as a comprehensive closure water balance model for the tailings impoundment complex. This paper describes the results of the long-term closure water balance for the tailings impoundment complex for the pre-closure state of the impoundment, as well as predictions towards the impoundment performance once final rehabilitation of the tailings impoundment complex has been achieved. The water balance presented is unique in that it is founded on unsaturated flow principles and accounts in full the impacts of the surface flux boundary conditions. This novel approach enables the prediction of actual infiltration rates into the tailings impoundment surface, which in turn allows for the calculation of how much seepage will exit from the tailings dam toe drains.

Jan 1, 2003

By M J. Shearer

An investigation into the reliability of the data being collected at the Mount Isa Mines site operated by Glencore in Queensland allowed on-site ventilation personnel to scrutinise pressure and volume measurements collected from the primary surface fans. The investigation effectively identified discrepancies being reported to the on-site remote monitoring system. The difference between the real-time and static measurements on the P63 RAR shaft identified that the in situ differential pressure transducer and piezo annubar system was not operating correctly. This indicated a deficiency of approximately 30 per cent reporting back to the remote monitoring software versus the live readings measured with the Pitot tube bomb and ALNOR AXD610 pressure micro-manometer.Constant monitoring of an operations ventilation network is imperative to ensuring that the underground atmosphere provides a safe and healthy workplace. Further benefits to real-time monitoring allows for the early indication of network failures and promotes increased availability. An innovative approach to out engineer and improve the existing measuring equipment from the 1970s was sought.The use of ultrasonics in the mining industry is not new with ventilation management systems (VMS) equipment available within the marketplace. The introduction and implementation of a reliable product for real-time monitoring was a challenge to overcome due to limited access and suitable measuring points within the mine. The available equipment on the market through mainstream suppliers was not suitable for the unique application required due to the in situ installation of the surface fans. A solution was identified in the oil and gas industry through collaboration and innovative thinking. This paper describes the sustainable approach to implement a reliable air flow monitoring system on-site.CITATION:Shearer, M J, 2017. Case study – an analysis of reliability and efficiency: ultrasonic versus annubar technologies, in Proceedings Australian Mine Vent Conference 2017, pp 51–56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By J Harris, J Turner, P Kirsch

Coal mining is recognised globally as a hazardous activity, and as a result operates under high levels of regulatory and public scrutiny while managing a workforce operating in a high-risk environment. Mining companies have developed sophisticated risk assessment procedures, management systems and personnel competency requirements that facilitate the safety and health of employees, and Australia is a world leader in coal mining safety and health.RISKGATE is an Australian Coal Association Research Program funded online platform that delivers broad cross-industry knowledge about current practice in the identification, assessment and management of coal mining risk. Centennial Coal has engaged with the RISKGATE program, managed by the University of Queensland’s Minerals Industry Safety and Health Centre, since its inception in 2010, and contributed topic experts to many modules, including underground topics within the geological and geotechnical domain (strata underground, outburst, coal bumps and bursts, and inrush).In 2013, Centennial Coal experienced significant unexpected strata failure at the Mandalong mine without any personal injury or fatality. This paper presents a case study in the application of RISKGATE to management of this unwanted event, the steps that were implemented, the information that was sourced and the contribution that RISKGATE made to the final outcomes. The Australian coal industry is encouraged to embrace our knowledge platform, and to also openly share processes and practical outcomes that result from integration of RISKGATE in mining operations.CITATION:Harris, J, Turner, J and Kirsch, P, 2014. Case study – application of RISKGATE to managing strata failure in an Australian coalmine, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 55–60 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Patrick Rennkamp, Wolf-Dieter Trodel, Andy Fearn

"The Jansen shafts are completed using purely mechanical excavation. This paper summarises the geology, a description of the shafts, the method used for excavation and the results achieved along with the challenges encountered and the solutions developed during the project. This experience is now being applied in the next generation machines and shaft sinking processes. This pioneering approach is changing shaft sinking in soft and medium to hard rock. INTRODUCTION The Jansen Mining project located approximately 150 km east of the city Saskatoon is the location of the BHP owned potash mine with an expected mining output of eight million tonnes annually upon completion. Mining contractors DMC Mining Services have used two Herrenknecht Shaft Boring Roadheaders (SBRs) to excavate the two blind shafts with an approximate excavation diameter of ten metres (inner diameter approximately 8.3 m) to depths of -975 and -1005 metres, respectively. The SBRs excavate the rock by a partial-face cutting method, using a transverse cutting drum mounted on a telescopic boom. The excavated rock is then conveyed away from the bench by an innovative pneumatic system and transferred into muck buckets to be hoisted to the surface. No drilling and blasting was done to keep to the BHP philosophy of using only mechanical excavation for this reference project. BHP VISION – MECHANICAL EXCAVATION BHP focused on mechanical excavation at Jansen due to the following perceived benefits: 1.No workers in the excavation chamber (shaft bottom), minimizing the exposure to traditional shaftsinking hazards associated with working in the shaft bottom. 2. Minimal damage to the rock fabric reducing the need for ground support and avoiding potential impact damage to freeze tubes located around the shaft. 3. Accurate excavation diameters with no overbreak, reducing volumes of rock to be removed and replaced with concrete lining."

Jan 1, 2019

By G du Toit, P L. Gillot, M Swanepoel

Randgold Resources’ Loulo-Gounkoto Complex is one of the largest gold mining operations in Mali, West Africa. The mine, which is situated on the western border with Senegal, treats more than 4 Mt/a of ore through a conventional three-stage crushing and ball milling circuit followed by a carbon-in-leach plant. Ore supply is achieved by a combination of open pit and underground mining, with the majority of the ore supply sourced from the Gara and Yalea underground mines situated approximately 2 km and 6 km respectively from the gold plant.In 2011, Randgold Resources commissioned Golder Associates to perform an evaluation study for providing structural backfill to both the Gara and Yalea underground mines using the current gold plant tailings. The test work performed as part of the evaluation study concluded the need for a tailings cycloning and dewatering facility capable of producing slurry at a solids concentration of 65 per cent with a particle size distribution that had minimum 25 per cent passing 20 µm and less than 5 per cent of -5 µm material. Tailings desliming was required to ensure a consistent feed quality to the paste preparation plants and to ensure that the system would be capable of handling variation in the feed composition from the gold plant.WorleyParsons, previously TWP Projects, was contracted by Randgold Resources to complete the engineering design for the slurry preparation plant, whilst Golder Associates was retained to complete the engineering design of the two paste preparation plants.This paper discusses the test work, design considerations and engineering design of the slurry preparation plant, termed the ‘intermediate plant’, as well as all ancillary facilities required for the delivery of the deslimed slurry to the paste preparation plants located at the two underground mines.CITATION:Swanepoel, M, du Toit, G and Gillot, P L, 2014. Case study – engineering design for a slurry preparation plant for a paste application in West Africa, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 477–486 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By P Nichols, C te Kloot, A Harrison

Ernest Henry mine (EHM) is a sub-level caving operation located in north-west Queensland, Australia. Located below a previously mined open pit, the underground operation ramped up production to 6.8Mt/a in 2017. The EHM ore body dips at 45 degrees to the South and therefore requires each level to “step out” from the level above as seen in Figure 1. Within this step out zone it is important to both maximise recovery and allow for efficient operation of the underground workings production to bring the level up to full production as quickly as possible. Throughout the step out design process, a combination of further defining the ore boundary, using lessons learnt from production performance on upper levels and the introduction of design improvements, has reduced the production ramp-up time, decreased costs and increased recovery for a single level at EHM. CITATION: Nichols, P, te Kloot, C and Harrison, A, 2018. Case study – Ernest Henry Mine: designing step out zones in an inclined sub-level cave, in Proceedings Complex Orebodies Conference 2018, pp 53–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By A. Rai

"This paper provides an overview of the current use of auxiliary ventilation product and the challenges with limited air quantity in dead-end entry or working face. The PVC low frictional factor, low physical constraint and minimum leakage ventilation duct was development with ""made in US and used in US"". The PVC duct development covering operational and total cost of ownership with on-going success will be presented. This paper will discuss mine sites using new PVC vent duct underground and the results from operational and technical side making a difference. INTRODUCTION The Turquoise Ridge Joint Venture (TRJV) is located in northern central Nevada, and is situated within the Basin and Range province, near the northeast end of the Osgood Mountains (see Figure 1). The TRJV mine consists of typical Carlin type- gold mineralization characterized by low strength rock of altered limestone’s, siltstones, and mudstones. The weak nature of the ground facilitates the underhand cut and fill mining methods [3].Mining Method; Underhand cut and fill : The mine uses underhand cut and fill method which has 12’x12’ top cuts and several different size undercuts. The ore body is accessed off of a secondary development heading, utilizing a heading with a cross section of 14W x 14H or 15W x 16H configuration. In the wider and more massive zones, two headings in a production panel may be worked at any one time. Drift round lengths are determined by the type of drilling machine being used. An example of a typical topcut and associated undercut layout is shown in Figure 2. SECONDARY / AUXILIARY VENTILATION IN UNUNDERGROUND METAL MINES The auxiliary ventilation system provides the required air volumes at the face of dead-end developments and production workings, which in many cases may be considered as the primary method of assuring that the air quantity and quality standards in these working areas are satisfied. The Auxiliary fans and ducting systems are usually the primary means of delivering the required air volumes to the face of dead-end developments and production workings. Both centrifugal and axial-flow fans are used in underground auxiliary ventilation systems, usually electric powered. The internally direct driven axial-flow fans tend to be more popular because of their compactness and adaptability to staging. The most commonly used materials for ridged tubing are coated steel, alloyed steel, fiberglass and resin. Flexible (collapsible) ventilation tubing is also used and is usually made from neoprene-coated or nylon material. To add stiffness and reduce collapsibility these fabric ducts can be formed over a steel spring frame. A very important factor in the design of an auxiliary ventilation system is to minimize leakage and reduce the frictional pressure losses along the auxiliary ducting systems by minimizing their friction factors (K)."

Jan 1, 2015

By T. Weatherwax, A. Rai, J. Poor

"This paper provides an overview of the current use of auxiliary ventilation products and the challenges with limited air quantity in dead-end entry or working faces. The PVC’s low frictional factor, low physical constraint and minimum leakage properties were ideal to develop as ventilation duct in conjunction with the concept of ""Made in the US and Used in the US"". The PVC duct supports the operational and total cost of ownership with on-going success. This paper will discuss the continuous improvement made in ventilation ancillary products for optimum results. The paper will also cover mine site usage of second generation PVC vent duct underground and the results from the operational and technical side making a difference in health and safety and overall auxiliary ventilation. INTRODUCTION The Barrick Turquoise Ridge Inc. (TR) is located in northern central Nevada, and is situated within the Basin and Range province, near the northeast end of the Osgood Mountains (see Figure 1). The TRJV mine consists of typical Carlin type- gold mineralization characterized by low strength rock of altered limestone, siltstones, and mudstones. The weak nature of the ground facilitates the need for underhand cut and fills mining methods.Mining Method; Underhand cut and fill: The mine uses underhand cut and fill method which has 12’x12’ and or 14’x14’ top cuts with several different size undercuts. The ore body is accessed off of a secondary tertiary heading, utilizing a heading with a cross section of 14W x 14H or 15W x 15H configuration. In the wider and more massive zones, two headings in a production panel may be worked at any one time. Drift round lengths are determined by the ground conditions and drift dimension. An example of a typical topcut and associated undercut layout is shown in Figure 2."

Jan 1, 2016

By K. Huttu, A. van Wageningen

"The Kittila underground mine is extracting one of the largest known gold deposits in Europe and has an estimated mine life through 2034. The Kittila mine is located in the Lapland region of northern Finland, approximately 900 kilometres north of Helsinki and 150 kilometres north of the Arctic Circle. The ore at the Kittila mine is refractory, making gold extraction relatively difficult because the gold is generally locked inside the two main sulphide minerals – arsenopyrite and arsenic-rich pyrite. The orebody consists of a complex pinch-and-swell structure including up to 100 different gold mineralization lenses. Fluctuating gold prices and other economic considerations increase the need to maintain and update the mining plans more frequently. Over 3,000 stopes need to be designed and optimized once a year for the LOM-plan and more frequent updates are needed for mid- and short term plans as well as production studies. As a large part of ore body is very sensitive to cost and gold price changes, stope optimization is crucial to find the best possible production scenario for every moment. Kittilä has gone through several methods for stope design and optimization. Most recently the Deswik Stope Optimizer (Deswik.SO) has been successfully used. Dewsik.SO has helped Kittilä to design and optimize stopes in a timely and cost efficient manner. Together with the Deswik suite of planning tools, reliable and auditable plans are created. This paper describes the methods used for stope design and optimization at Kittilä. THE KITTILÄ MINE The Kittila underground mine in northern Finland is extracting one of the largest known gold deposits in Europe. Kittila achieved commercial production on May 1, 2009, becoming Agnico Eagle’s first mine to open outside of Canada. The Kittilä orebodies were initially mined from two open pits – Suuri and Roura – and underground operations were added in October 2010. The pits were mined out in November 2012, so mining is now entirely underground in the Suuri and Roura deposits. Additional, small open pits will mine any remaining near-surface reserves in the future. The Kittila mine is located in the Lapland region of northern Finland, approximately 900 kilometres north of Helsinki and 150 kilometres north of the Arctic Circle. With a mine life estimated through 2034, Kittila is Agnico’s longest-life mine. The mine’s proven and probable reserves contain 4.7 million ounces (32 million tonnes at 4.6 g/t gold). Ore has been mined from underground since 2010. The original 3,000-tonne-per-day operation underwent an expansion project to increase the throughput capacity of the mill by 1,000 tonnes/day, starting by the end of 2014. The region around the Kittila mine is underlain by mafic volcanic and sedimentary rocks of the Kittila Greenstone Belt oriented nearly vertical. This greenstone belt is similar to those hosting Agnico Eagle's Canadian deposits in Quebec’s Abitibi region and Nunavut. At the contact point between iron-rich and magnesium-rich rocks lies a 100- to 200-metre-thick structural zone known as the “Suurikuusikko Trend”. This trend hosts the Kittila deposit, where multiple mineralized zones have been traced over a strike length of more than 25 kilometres."

Jan 1, 2015

By J Foster

The Lanfranchi Nickel mine is located approximately 48 km south of Kambalda in Western Australia. Mining first commenced in the mid-1970s under the previous owner, Western Mining Corporation Ltd. After two years on care and maintenance, Panoramic Resources (previously known as Sally Malay Mining Ltd) purchased the operation in November 2004. The site currently produces approximately 10?000 tonnes of nickel metal annually from approximately 430?000 tonnes of ore. The Ore is mined from four main orebodies; Deacon, Helmut South, Lanfranchi and Schmitz. The Helmut South orebody is situated approximately 790 m below surface and extends to a resource depth of 940 m. Horizontal thickness of the orebody ranges from 10 m to 45 m in width, with the average being 30 m. Previous mining at the Lanfranchi operations specifically the Helmut orebody, had a history of seismic activity. When Panoramic Resources acquired the operation it was decided that seismicity was going to be an issue and therefore a mining method needed to be selected that could effectively manage this potential risk. The dip of the orebody is quite shallow at 45º, with a 30º plunge to the south . The hanging-wall comprises of very weak ultramafics. Due to these factors the orebody posed several mining challenges. To safely and effectively mine the Helmut South orebody in the Lanfranchi Nickel mine, underhand cut and fill mining was selected as the most appropriate mining method. Paste fill comprising of cemented gold tailings was the backfill of choice. This paper is intended to convey some of the key learnings from the use of a mining method that has not been commonly practiced in Australia.

Mar 21, 2011

By T. Gong

Often plans to increase plant throughput provide an opportunity for optimising plant equipment and operating methods. This was the case in 2005 at TISCO Jianshan Iron Mine, when an increase in production was planned. The thickening circuit had presented a limitation to the plant throughput and operation with poor overflow clarity and underflow density. Following a course of test work by Outotec, a 53m diameter Supaflo® High Rate Thickener (HRT) was selected for the duty. From early stages of operation of the new thickener, the benefits have been dramatic, including: ? Improved tailings underflow density by 9% ? Improved Overflow clarity to less than 150ppm ? Considerably decreased the water and energy consumption as well as operation cost ? Stable and reliable operation This paper looks at this installation as a case study and compares the previous thickener installa-tion performance with the performance of the single 53m HRT.

Jan 1, 2014

By Brian Lewis, Reinhold Daykin Schnell

Blasting is the primary and most effective method for breaking and moving material at most mine sites. The blast design is often adjusted in efforts to optimize the effectiveness of the blasts’ explosive energy while minimizing costs. When adjusting blast design parameters, it is important to adjust one parameter at a time, observing and analyzing the potential effects of the change on the overall blast performance.

Feb 6, 2023

By A. Jennings, J. Cornet, P. Perrone

Controlling long overland conveyors with multiple drive stations is a complex problem. The methods for controlling these belts in a steady state are well-covered in existing literature, but a discussion of starting and stopping strategies is absent. This paper outlines different control strategies for starting, stopping and running conveyors with multiple drive stations. To illustrate the benefits of applying the methods described in this paper, the authors show how their adoption corrected many of the control system problems at Essroc Cement’s overland conveyor, which features three drive stations separated from each other by long lengths of continuous conveyor belt.

Jan 1, 2013

By A. Jennings

[ ] In November 2005, Essroc Cement, part of the Italcementi Group, commissioned a long overland conveyor at their Nazareth plant in Pennsylvania. This conveyor, tagged CV-105, was designed to transport 1000 tph of limestone from the quarry to the kiln, and 400 tph of hot clinker (at 300°F) at back from the kiln to a handling facility about halfway back. Conveyor CV-105 is 8969 ft (2733 m) long. It gains 152 ft (46 m) of elevation in the first 1570 ft (480 m), then is mostly flat for the remaining 7400 ft (2250 m) (Figure 1). After the limestone is discharged at the head pulley, hot clinker is loaded onto the return side of the belt. This clinker can be discharged at one of two locations.

Jan 1, 2012

By Kyle R. Lackner, Jared P. Williams

"The Sutter Butte Flood Control Agency initiated the Feather River West Levee (FRWL) Program in 2010 to bring 35 miles of levee along the Feather River into compliance with applicable Federal and State standards for levees protecting urban areas. A combination of soil-bentonite cutoff walls, soil-cement-bentonite cutoff walls, and seepage berms will reduce flood risk by correcting under and through seepage deficiencies and remove more than 34,000 properties from the FEMA Special Flood Hazard Areas. The FRWL program includes a combined total of 7,744,803 square feet (SF) of cutoff wall planned to be constructed between 2013 and 2015. Cutoff wall construction methods to meet the design depths included conventional excavation to a depth of 85 feet and deep soil mixing for depths up to 120 feet. A key component of the FRWL program was the development of site specific mix designs using the design boring logs to evaluate the expected backfill gradation and permeability results. Issues that required a partnership between Contractors, Owner and Engineers included substantial Archaeological and Cultural Resource delays, significant depth changes due to a change in competent key, right of way acquisitions for abutting land, and the magnitude of the project in a resource limited industry.IntroductionThe Feather River watershed basin is located 50 miles north of Sacramento, CA and incorporates the agriculture producing communities of Yuba City, Live Oak, Gridley and Biggs. These communities are protected from flooding by levees that contain under-seepage and through-seepage deficiencies and were the cause of major failures in 1955, 1986 and 1997. The Feather River West Levee (FRWL) program was initiated by the Sutter Butte Flood Control Agency (SBFCA) in 2010. The long term objective of SBFCA is to correct the levee deficiencies and provide 200 year flood protection to more than 34,000 at risk properties located within the FEMA Special Flood Hazard Areas.Although FRWL contained a variety of construction components such as earthwork and pipe replacement, the slurry cutoff wall is the primary construction element for addressing under and through seepage deficiencies. From 2013 to 2015 approximately 6,649,210 SF of cutoff wall were installed using conventional excavation and deep soil mixing (DSM) techniques leaving 1,095,593 SF to be completed in 2016. The work was designed, solicited and constructed under two separate contracts, titled Project Area C and Project Area B&D. A summary of the contracts and cutoff wall quantities is presented in Table 1."

Jan 1, 2016

Spiral concentrators are compact, cost-effective and generally efficient gravity concentration separators for a wide range of applications (for example: coal, beach sands, iron ore, chromite and tantalite). Large mineral processing plants consist of thousands of spiral concentrators resulting in large plant footprints (capital intensive) and the adjustment of splitters is time consuming, impractical and is in many cases neglected?high capacity (HC) spiral concentrators aim to address these shortcomings. As a result Exxaro Namakwa Sands is currently investigating high capacity spiral technology for the spiral circuit upgrade at the primary concentrator plants (PCPs). This article summarizes the rougher spiral performance evaluation that was conducted on different types of spiral concentrators (the traditional MG4 spiral concentrator and the high capacity (HC) spiral concentrator) under different feed conditions. In addition, the effect of slimes on the spiral concentrator performance was also investigated. Slimes rheology was linked to the poor concentrator performance at the higher slimes concentrations. The test campaign shows a sacrifice in recovery under design-feed conditions can be expected when using high capacity spiral concentrators in the rougher stage when compared to traditional spiral technology currently in use. Both spiral concentrators show a detrimental impact of slimes on the performance, but the high capacity spiral concentrator is more sensitive to the higher slimes conditions.

Jan 1, 2010