Search Documents

By M. Kung, D. Schwegler-Berry, V. Castranova, D. Lewis, H. Abrons

Pulmonary responses to coal mine dust exposure were investigated by analysis of bronchoalveolar lavage specimens from non-smoking coal miners (n-12, mean age-43 ± 2 years, mean underground exposure-17 ± 2 years) and from non-smoking normal volunteers (n-18, mean age-43 ± 2 years). Spirometric and diffusion capacity indices were monitored as part of a physical exam. Lavage was performed in a subsegment of the right middle lobe by instillation of 200 ml of warmed saline solution in 50 ml aliquots and recovery by gentle suction. Specimens were centrifuged at 500g for 5 minutes at 2°C. Total and differential cell counts were recorded. Secretion of oxidants measured by chemiluminescence, surface morphology (spreading and ruffling), and lymphocyte parameters were determined. Lavage fluid was analyzed for the presence and quantity of acute phase reactants and immunoglobulins. Pulmonary function measurements as well as recovered lavage volume, total lavagable cells, and differential cell counts were similar in both miners and controls. Both resting and phorbol myristate acetate-stimulated chemiluminescence were also similar in miners and controls. In contrast, particle-stimulated chemiluminescence was significantly decreased in the alveolar macrophages from the miners (48% of control values). Morphometric analysis of scanning electron micrographs indicate that phagocyte surface spreading was similar in miners and controls. However, surface ruffling was 127% greater in the miners compared to controls. Lymphocyte subpopulations were similar in miners and controls. Protein analysis of the lavage fluid revealed lower total protein content in the lavage fluid of miners. However, the concentration of albumin, IgG, and IgA were similar in miners and controls. We conclude that most indices were normal in underground miners working under the current dust standard of 2 mg/m3. The decrease in particlestimulated chemiluminescence and the increase in surface ruffling in miners may suggest the beginnings of particle overload and activation of the macrophages. In addition, a decrease in total protein was noted in lavage fluid from miners.

Jan 1, 1991

By William H. Pailes, Vincent Castronova, Daniel Lewis, Norman L. Lapp, George Goodman

"INTRODCJCTIONAlveolar macrophages are free lung cells located on the surface of small airways and alveoli. These phagocytes play an important role in the protection of the lung against airborne bacteria and particles.1 However, hyperactivation of pulmonary phagocytes can lead to excessive secretion of enzymes and reactive oxygen species which could result in lung injury, emphysema, or fibrosis.2,3 Analysis of bronchoalveolar lavage effluents for cell types and cellular activity has yielded information concerning the etiology of various pneumoconioses. For example, emphysema associated with inhalation of coal dust or cigarette smoke has been related to enhanced secretion of reactive oxygen species from alveolar macrophages.4-7 In contrast, hypoactivation of alveolar macrophages has been associated with inhalation of diesel particulates"" and has been related to increased susceptibility to pulmonary infection. s Inhalation of cotton dust has been associated with dramatic increases in lavagable polymorphonuclear leukocytes9 while pulmonary sarcoidosis and silicosis have been related with high numbers of lymphocytes in lavage effluentsl0,11The objective of the present study was to obtain lavage effluents from 8 control subjects, 8 healthy power plant workers exposed to fly ash, 1 healthy coal miner, and 1 rock driller with acute silicosis. These effluents were analyzed for total numbers of alveolar macrophages, lymphocytes and neutrophils and for secretory activity of alveolar macrophages. Data were then analyzed to determine what response patterns were characteristic for given dust exposures.METHODSSelection of SubjectsThe 8 control subjectS were all adult males from the area of Morgantown, WV. Two subjects among the controls had smoked cigarettes for approximately three pack-years and had stopped more than ten years ago. The 8 power plant :workers were all healthy adult male employees of a power facility in Hatfield, PA, approximately thirty miles from Morgantown. One of the power plant personnel was a comparable ex-smoker. The remaining subjects were all lifelong non-smokers. The coal miner was a healthy non-smoking male from Morgantown, WV. The rock driller was a patient under treatment with corticosteroids for acute silicosis. He had shown considerable clinical improvement with this treatment but still manifested significant radiologic and pulmonary functional abnonnalities at the time of lavage. The mean age of the 8 control subjects was 36 years (range: 31 to 49 years); the mean age of the remaining subjects studied was 38 years (range: 29 to 53 years)."

Jan 1, 1990

In the five years since Great Central Mines Limited (GCM) commenced exploration in the Jundee and Bronzewing areas of Western Australia's Yandal greenstone belt, the Company has been transformed from a junior explorer into Australia's fourth largest gold producer with annual production of approximately 440 000 ounces and mineral resources of seven million ounces of gold.The growth in resources has been driven by a high quality geoscientific approach, supported by a substantial budget for drilling and strong management commitment. In 1997, the Company expects to spend US$30 million on exploration in the Yandal greenstone belt.

Jan 1, 1997

By L. J. Barnes

The process for bio-remediation of sulphidic slag (BROSS) operates at 45 degrees C in a neutral (pH 7), aerobic aqueous environment in which sulphide in the slag is converted to sulphate. A two-stage version has been developed that involves quantitative chemical pre-oxidation of total sulphide to thiosulphate, followed by complete biooxidation of thiosulphate to sulphate. Ferric hydroxide, also produced, acts as a flocculant in the bioreactor effluent, concentrating heavy metal precipitates in the thickener as a sludge which can be returned to the smelter. The process has a high sulphate production rate and low acid and nutrient consumptions. Microorganism growth is the rate-limiting stage, requiring a minimum liquid residence time in the bioreactor of about 7 h. Although large quantities of oxygen are needed, sufficient gas mass transfer can be attained in an air-lift reactor. Products are an aqueous stream containing sodium sulphate with only trace levels of toxic heavy metals and a benign, toxic metal-containing sludge

Jun 18, 1905

By Wido Tilmann

13.6-1. Importance. In Germany there are large tertiary brown coal reserves, most of which are located close to the surface. Therefore, brown coal has been recovered for many years by means of opencast methods. By utilizing a high degree of technology, a rational operation has been achieved, and as a result, the mining techniques have become renowned all over the world. After the war, all the dredgers and overburden spreaders, as well as the means of conveyance, had to be redeveloped for adapting this equipment to the changing conditions of the deposits. Numerous auxiliary machines were adopted from the American earth moving industry and altered according to the different requirements. As a result of such technical developments, the output per man and per shift was increased remarkably in spite of the deterioration of the geological conditions. In the whole of Germany, the total reserves of brown coal amount to 100 billion metric tons, of which 60 billion tons are situated in the Federal Republic of Germany. In the latter area, 8.5 billion tons will be recover- able by opencast means, of which 3.5 billion tons are already developed. The annual output reached 102 million tons in 1965. This total figure comes from four different mining districts: Rhineland, Helmstedt (town at the border of the Soviet occupied zone), Hesse, and Bavaria. The production figures (1965) are as follows: [ ]

Jan 1, 1968

By Hibbert W. D, Lottrey A

The behaviour of coal in a process is a function of both the coal properties and the processing conditions. In the case of the Loy Yang coal deposit, extensive testing has been undertaken to determine: ò the extent, distribution and structure of the coal resource; ò the variations in properties throughout the resource; and ò evaluation of the behaviour of the coal during processing. This has involved the conduct of an extensive borehole drilling program, backed by geological modelling and material characterisation (chemical, physico-chemical and petrological). Evaluation of the behaviour of the coal during processing has ranged from theoretical modelling, laboratory-scale investigations through to pilot scale and full-scale tests. Until recently, the bulk of the work was directed at evaluating the behaviour of the coal for existing pulverised fuel (pf) firing/steam boiler technology and a high level of understanding has been developed of both the coal resource and its behaviour within these systems. More recent efforts have been directed towards the evaluation of new technologies directed towards cheaper and more efficient power generation using this coal. Loy Yang coal has been evaluated in the following technologies: ò Hydrothermal dewatering/direct coal-fired gas turbine; ò Steam fluidised bed drying; ò Solar drying/densification; ò Briquetting; and ò Gasification.

Jan 1, 1992

By Waghorn EP, Gleeson HB

The Loy Yang Optr, Cut is a brown coal mine bring developed in the Latrobe Valley region located some 160 kin south-east of Melbourne, Victoria. The mine has been designed to supply a mine mouth power station at a rate that will rise to 32 million tonnes per year by the mid 1990's. Continuous mining metnuds are employed using bucket Whtel excav- ators and conveyors. This paper describes the basis of the design of the Loy Yang continuous mining system ano cne experience of four years of initial operation.

Jan 1, 1987

By WALTER B. JONES

PIG iron was first produced in Alabama in 1818 from limonite or brown ore and since then much of this ore has come from the so-called mineral district of northern Alabama, especially along the Cretaceous-Paleozoic contact. For many years the Russellville district in Franklin County, where the first blast furnace was erected, produced more than 100,000 tons of brown ore annually. Limonite has been reported at many places in the Coastal Plain region, where the formations are of Mesozoic and Cenozoic age, but these scattered deposits were never considered to be of much commercial importance. However, in the last three years a considerable quantity of this ore has been scraped up and shipped, particularly from the city of Greenville in Butler County.

Jan 1, 1938

By Chris Larsen, Ian Orford, Marilene Renaud, Mike Cooper, Lud Strah

"An AG/SAG mill was commissioned at the Brunswick Mine concentrator in October 1998. This paper discusses the original liner design for the bi-directional AG/SAG mill, observed liner wear, subsequent liner design modifications, and benefits. The mill liners consist of steel top hat shell liners, steel end liners, rubber grates and rubber lined pulp lifters.Lifter profile and plate thickness measurements were made on monthly shop days. Trends of wear rates were used to project when liners required replacement. Wear profile information was also used to determine where liner re-design would improve wear life or minimize scrap loss. Charge motion simulation modeling was used as a tool to assist liner design modifications.INTRODUCTIONThe Noranda Inc. Brunswick Mine, located near Bathurst, New Brunswick, is a large underground lead/zinc mine with a nominal production rate of 10,000 tonnes per day. The Brunswick concentrator commenced operation in 1964 with conventional surface crushing followed by rod and ball milling to reduce run of mine ore to the required size to feed two parallel flotation circuits. In 1998 the AG (autogenous grinding) mill was commissioned for a nominal production rate of 9,000 tonnes per day replacing two surface crushing plants, three rod mills and three primary ball mills. In May of 1999 the mining rate was increased and the service of the AG mill was changed to a SAG (semi-autogenous grinding) mill with the addition of 4 inch steel balls (4% volume). The mill operates in closed circuit with 0.66 meter horizontal cyclones to produce a ground product of 90 micron nominal size (K80).The AG/SAG mill liners are steel (Norsteel, chrome-moly steel) with rubber grates and rubber lined pulp lifters.The original liner design was based on studying other AG/SAG mills and recommendations by the liner supplier, Norcast. Design factors taken into account were total cost of lining (including material and labour), protection of mill shell and impact on operating performance."

Jan 1, 2003

By R. J. R. Welwood, F. J. Grebenc

"Brunswick Mining and Smelting Corporation Ltd. (controlled by Noranda Mines Limited) operates two lead-zinccopper- silver mines approximately 20 miles inland from Bathurst, N.B. The principal No. 12 orebody is mined by underground methods; the second, the No. 6 orebody (6 miles away), is recovered by open-pit mining. No. 12 underground operations ar•e in two parallel massive sulphide orebodies about 400 ft apart, dipping at 75 to 80 degrees and plunging almost vertically. The initial mining phase involved longhole open stoping from the 1550 level to the crown pillar, with main levels at 150-ft intervals and sub-levels between at 75 ft. Stope dimensions average 120 ft long, 100 ft wide and 400 ft high, with alternate rib pillars as well as sill and crown pillars. Initially, ore was transferred through scram drifts below each stope by means of 125-hp electric slushers and 72-in. folding scrapers, being delivered to gravity ore-pass collection •systems feeding a primary jaw crusher below. Later, track and trackless drawpoints were utilized below most longhole open stopes and pillars. Rib pillars were recovered by longhole methods, with large blasts into a central slot and undercut, after adjacent stopes had been filled. Waste-rock stripping from No. 6 open pit has been supplied to No. 12 stopes as backfill, by means of gravityfill raises.In 1968, the decision was made to mine the remaining ore zones by mechanized cut-and-fill methods, utilizing Load-Haul-Dump equipment. Currently, approximately 60 per cent of No. 12 mine production comes from mechanized cut-and-fill mining. As before, backfill is supplied from No. 6 open pit stripping waste rock, which has been crushed to minus 6 in. The ultimate objective is to supply virtually all production requirements by mechanized cut-and-fill techniques. The No. 6 open pit, which commenced production in 1966, covers an area of 1,500 by 1,200 ft, equivalent to 41 acres approximately. Ramp roads are graded at 8.5 per cent. Each mining bench is 36 ft high and the ultimate pit will consist of 14 benches for a final pit depth of 504 ft. Present depth is 180 ft."

Jan 1, 1971

By R. Le

"The principles of noise control aredescribed with particular emphasis on personalactive units as opposed to passive ear muffspresently in general use. A discussion followsfor their potential use in a mining environment.RÉSUMÉNous décrivons brièvement quelquesprincipes de contrôle de bruit à l’usage person-nel, puis nous passons en revue quelquescasques commerciaux dotés de ces circuits àprincipe actif. Enfn nous discutons de leurusage potentiel dans le contexte minier.IntroductionLe casque à principe actif est un produitqui existe commercialement, mais encore peurépandu en usage, sûrement à cause du prix,mais aussi de sa méconnaissance par le grand public. Il arrive parfois qu’un journaliste trouvele produit fantastique et le médiatise commeune réalisation de son pays (ou de sa province),mais peu savent qu’il s’agit là d’un principe quia commencé dans les années 30. Par delà lesensationnel, il reste que si l’on veut mettre lamain sur un de ces casques pour l’essayer, on nesait où l’obtenir. De plus, les casques n’utilisentpas tous le même principe actif. C’est la raisonpour laquelle nous faisons cette brève compara-ison. Nous le faisons en mettant l’accent pourune possible utilisation dans le domaine minier,car c’est dans ce milieu que les usagers sontconfrontés aux bruits les plus intenses qui peu-vent endommager leur système auditif, ce quin’exclut pas les autres situations (travaux publics, foresterie, écoute hi-f, etc.)."

Jan 1, 1997

By W. M. Cross

Bubble attachment time measurements for the rare-earth phosphate minerals monazite and xenotime were made as a function of oleate concentration, sodium fluoride addition, and temperature. Results indicate that the rare-earth phosphates behave similarly to other phosphate minerals, notably collophanlte and fluorapatite, which have been studied previously. The addition of sodium fluoride yielded a modest decrease in bubble attachment time with fluoride additions below the apparent fluoride surface precipitation point, while at fluoride additions greater than the apparent precipitation point a significant decrease in attachment time occurs. Increasing the temperature or the system gave a slight decrease in bubble attachment time in the absence or sodium fluoride. With sodium fluoride addition and below the apparent fluoride surface precipitation point, an increase in temperature actually increased the attachment time. For sodium fluoride additions above the apparent fluoride surface precipitation point, a temperature increase significantly decreased the attachment time.

Jan 1, 1989

By Stefaan J. R. Simons, Michael T. Spyridopoulos

In this paper the effect of humic substances (natural surfactants), electrolytes and solid particles on bubble coalescence, and as a consequence on froth stability, has been investigated. We formed two bubbles of equal size and forced them to collide using a novel experimental apparatus. The interactions were recorded by a high-speed camera, the images of which helped to determine the coalescence frequency and the coalescence time, as well as the mechanisms of the interactions. Two types of humic substances were used, along with three different electrolytes. Humic substances appeared to have a considerable effect on bubble coalescence, while the effect of electrolytes was minimal. Moderate and high hydrophobic glass spheres were used between two bubbles. Very hydrophobic spheres promoted fast bubble coalescence, while moderate hydrophobic spheres had no effect. We present data of coalescence frequency and time, as well as images of the coalescence events.

Jan 1, 2003

By S J. Neethling and, S J. R Simons

In this paper the effect of humic substances (natural surfactants), electrolytes and solid particles on bubble coalescence, and as a consequence on froth stability, have been investigated. In this study two bubbles of equal size were formed and forced to collide using a novel experimental apparatus. The interactions were recorded by a high-speed camera, the images of which helped to determine the coalescence frequency and the coalescence time, as well as the mechanisms of the interactions. Two types of humic substances were used, along with three different electrolytes. Humic substances appeared to have a considerable effect on bubble coalescence, while the effect of electrolytes was minimal. Moderate and high hydrophobic glass spheres were used between two bubbles. Very hydrophobic spheres promoted fast bubble coalescence, while moderate hydrophobic spheres had no effect. Data of coalescence frequency and time is presented, as well as images of the coalescence events. The coalescence frequency was used to validate a parameter, Pf, known as the film failure frequency, used in a simulation model to predict foam height in a gas-sparged vessel. Predictions determined using Pf were then validated by experimentation.

Jan 1, 2005

By J J. J Chen, J C. Zhao

A water/air model was developed to simulate the refining of molten aluminium by the sparging of gas through an impeller. The optimal gas dispersion depends upon selecting the correct gas rate for a given impeller rotational velocity to prevent flooding or channelling. Correlations illustrating this flooding behaviour exist for standard impellers within standard tank geometries. However the validity of these correlations has not been substantiated for gas dispersion in high temperature molten metals with non-standard tank and impeller dimensions. Metal refining is most efficient when fine bubbles are generated and uniformly distributed within the treatment tank. The application of some measuring technique able to detect this distribution within a non transparent operating treatment tank would be invaluable, enabling the optimisation of gas flow and impeller speed.   A technique has been developed to measure the pressure fluctuation levels at specific points in the water model. Comparison of these pressure fluctuation data with photographic evidence obtained in the water model suggests that the flow regime in the metal treatment unit may be determined using this technique.

Jan 1, 1995

By D. Lelinski

Air-sparged hydrocyclone (ASH) flotation is one of the new promising technologies. Numerous applications have been successfully tested since its conception; nevertheless, research and development efforts have continued to provide for further improvements with respect to operating conditions and design considerations. Results from experimental studies on bubbles generation in the ASH system are presented in this paper. Bubble size distributions generated during ASH operation have been determined using a high-speed photographic technique. The influence of many factors including surfactant concentration, water flowrate, and porous tube pore size has been studied. Test results indicate that these process variables have a profound effect on the bubble size distribution. With an increase in surfactant concentration or water flowrate (shear field) the bubble size distributions become narrower and shift toward smaller average bubble diameters. However, the influence of pore size is more complicated. Depending on the experimental conditions the average bubble size was found to range from about 100 to 300 microns in diameter.

Jan 1, 1995

By David Seaman, J-P Franzidis, Emmy Manlapig

"A new device has been developed to directly measure the bubble loading of particle-bubble aggregates in industrial flotation machines, both mechanical flotation cells as well as flotation column cells. The bubble loading of aggregates allows for in-depth analysis of the operating performance of a flotation machine in terms of both pulp/collection zone and froth zone performance. This paper presents the methodology along with an example showing the excellent reproducibility of the device and an analysis of different operating conditions of the device itself.The device has been used to investigate the froth selectivity of attached particles. Simultaneous measurements were made using a different froth recovery measurement technique in the same flotation cell. A comparison of these techniques shows that in this case, particles are selectively detached from bubbles at or near the pulp-froth interface.INTRODUCTIONA flotation cell can be considered to operate in two distinct phases or zones; namely the pulp or collection phase and the froth phase. The pulp zone is responsible for the formation of hydrophobic particle-bubble aggregates, whilst the froth phase is responsible for the separation of these aggregates from surrounding suspended hydrophobic and hydrophilic particles. Thus, the froth phase is the grade determining phase in flotation. A measurement of the bubble load (the mass of particles attached to air bubbles in units of mass/volume) will enable the analysis of the performance of both the collection zone at creating bubble-particle aggregates and also the froth zone at separating these aggregates from surrounding pulp.A measure of froth zone performance that has been used extensively in flotation research is the Froth Recovery, Rf, of a particular system. Froth recovery is defined as the mass of particles collected in the concentrate launder by true flotation as a fraction of the mass of particles entering the froth phase. The measurement of bubble load allows for this term to be calculated easily, rather than having to go through the laborious task of, for example, changing froth depths to determine this performance criterion (Contini et al., 1988; Vera et al., 1999b; Feteris et al., 1987)."

Jan 1, 2004

Bubble Load Measurements in Flotation - A Critical Review of Current Practice

Sep 13, 2010

By G M. Evans, C M. Phan

This paper presents an analysis on the dynamic adsorption of frothers and collectors onto air bubbles in flotation. The analysis was carried out using the theory on the surfactant transfer by diffusion and adsorption. The bubble size was considered when solving the diffusion equation for the dynamic surface excess. The adsorption kinetics was modelled employing the Langmuir adsorption isotherm and its extension with the inclusion of the lateral interaction of the adsorbed molecules (the Frumkin adsorption isotherm). The numerical computation was applied to solve the governing equations. The dynamic adsorption of the surfactants was measured in terms of the dynamic surface tension for sodium dodecylbenzene sulfonate (SDBS) and Dowfroth 250, using pendant bubble tensiometry. The results show that for air bubbles with diameter of the order of 1 mm, the bubble size effect on the dynamic surface tension is small and the solution of the diffusion equation for a planar gas-liquid surface can be used to describe the dynamic adsorption onto the air bubbles. The experimental data obtained with SDBS were well described by the Frumkin adsorption isotherm and the molecular diffusion. The model description for the experimental data obtained with Dowfroth 250 required the kinetic equations. The paper is relevant for further analysis of the role of the adsorbed surfactants in the particle collection.

Jan 1, 2005

By Liu Q, Siefken T. C, Misra V. N

The bubble size was measured in a laboratory flotation column. The effect of variables such as air flowrate, frother dosage and type, pulp density, particle size and water column height on the bubble size was investigated. The results show that an increase in either air flowrate or pulp density cause the bubble size to increase, while increases in water column height, frother dosage, surface tension or solid particle size cause the bubble size to reduce. Among the frother types tested, MIBC was found to be the most effective in reducing the bubble size.

Jan 1, 1992