Search Documents

By Murad Y. Abu-Farsakh

This paper presents the analyses of load-transfer (t-z) behavior of twelve prestressed concrete (PSC) instrumented test piles that were driven in different locations of Louisiana. The load transfer method is an efficient and practical tool for the analysis of single driven pile to predict the ultimate load. The test piles were instrumented with vibrating wire strain gauges in order to calculate the shear transfer for different soil layers during the static load test. The static load test was performed on all the test piles after 10 to 14 days of end of driving. Empirical load-transfer models were proposed previously by different researchers (Fleming 1992, Hirayama 1990, Krasinski 2012, Bohn et al. 2017) after analyzing the instrumented test pile results. For this study, load transfer of each soil layer was measured and compared with the previously developed existing model. The stiffness parameter (M) for the hyperbolic equation was calibrated in order to best match the measurements. The good agreement of the proposed curves was then confirmed by applying them to assess the overall load-settlement curve of other pile load test results available in the literature. INTRODUCTION The load transfer mechanism (stress-strain relationship) for an axially loaded pile usually comprises of three loading mechanisms: axial deformation in the pile (z), soil skin friction along the shaft (qs), and soil end-bearing (qb). The development of soil skin friction with axial deformation is referred as the t-z curve, and the development of soil end-bearing with axial deformation is referred as the q-z curve. Figure 1 presents the load transfer mechanisms in an axially loaded pile and the corresponding spring mass models for t-z and q-z curves (API, 2002). In order to construct the load transfer curve in clay under vertical load, the axial load transfer (t-z) curve and end-bearing load transfer (q-z) for that particular soil should be assessed separately. The axial load transfer (t-z) method is probably the most widely used technique to study the problem of single axially loaded piles. Therefore, the load transfer through the shaft of the pile and are getting more and more important compared to the only the pile capacity analyses. The load transferred from shaft to the surrounding clay soil is a function of the width of the pile and the surface roughness of the pile and clay properties. The development of a representative procedure allows the assessment of the t-z curve in soil (sand and/or clay) that leads to the prediction of a nonlinear vertical load-settlement response at the pile head.

Jan 1, 2018

By Jonny López, Emérito Fernández

Con el objetivo de adecuada gestión de la extracción Au, eficiencia y predictibilidad en la estimación de producción, leyes de solución rica y caudal, MINSUR ha identificado oportunidades en el proceso de lixiviación mediante el análisis de variables críticas como las mineralógicas (alteraciones, leyes, contenido de finos) y las variables del proceso (pH, humedad, celdas bajo riego, tasas y ratios de irrigación, concentración de cianuro, distribución).

Sep 29, 2023

By Gisell Sumaria, Mike Martos

La analítica avanzada permite analizar los datos (en tiempo real, históricos, no estructurados, estructurados, cualitativos, cuantitativos, etc.) para identificar patrones, optimizar indicadores, mejorar procesos, generar conocimientos para informar y, en algunos casos, resolver conflictos con una mínima intervención humana, es decir, automatizar decisiones. El proceso analítico ha demostrado ser un excelente aliado para la toma de decisiones, o inclusive, desde el origen hasta la decisión, control y seguimiento de resultados del proceso.

Sep 29, 2023

By E. E. Krist, W. H. Sweetser

Sampling of an orebody has a number of purposes. In the initial phase, it is necessary to define the limits of the orebody and mineral content to the extent that it can be stated whether it is, in fact, an economic orebody. Also, samples must be generated so that geological and metallurgical evaluations can be made. Finally, when sufficient information concerning the geology, mineralogy, and metallurgy are known, a mining method and plan can be developed and the metallurgical; plants constructed to process the ores as they become available. With today's large, complex open pit copper mines, single sampling methods would be inadequate. Diamond drilling, percussion drilling, underground shafts and drifts all play a part in the total orebody, definition. At Anamax Mining Company's Twin Buttes mine, sampling and orebody definition.wil1 eventually lead to the existence of three metallurgical processing plants and, perhaps, an underground mining operation. A 30 000 tons per day sulfide concentrator was placed in operation in September 1969 and a 10 000 tons per day oxide leaching plant was placed into service in May 1975. The aim of this presentation is to historically discuss the orebody sampling that has been done at Twin Buttes, briefly describe the orebody, and discuss the analytical methods currently used to assist the geologist, metallurgist and mine planner in their respective evaluations.

Jan 1, 1978

By E. Krist

The newest addition to the Anamax Mining Company's Twin Buttes copper producing complex is a by-product uranium extraction plant which was placed into service in February 1980. The plant is unusual in that it is placed internal to the copper countercurrent decantation, solvent extraction, and electrowinning plant. The plant reached full production within a month and, to date, has produced continually above design rates.

Jan 1, 1981

By A. V. Shroff

The Indian Standards code of practice for design and construction of underreamed piles contains provision for installing such piles in expasive soils. In recent years, a large amount of research work has been carried out in the analysis, design, construction and performance of underreamed piles in expansive soils. This paper suggests that the results of this research field tests should be included in the code. Various additions and modifications as well as deletions that should be incorporated in the code are discussed.

Jan 1, 1996

The discovery of gold mineralization at the Manhattan mercury mine, Napa and Yolo counties, California in 1978 was the result of applying a new exploration ore deposit model in a region previously unprospected for gold. This discovery, the McLaughlin gold mine, owned and operated by Home-stake Mining Company, is a classic epithermal mercury-hot springs-gold deposit currently producing approximately 7,776,000 grams of gold annually.The exploration program that led to this discovery was based on a mercury-hot springs-gold genetic model. The model was developed using basic knowledge of ore-forming processes plus careful field observations made during examination of many known precious metal districts in. the Western U.S.A. Theoretically, hot spring systems could host gold deposits and, indeed, gold in these environments had been recognized for years. However, at the time of the McLaughlin discovery, it was not known to occur in sufficient quantities to inspire geologists to explore hot spring systems specifically for gold. Field observations recognized the presence of hot spring deposits and mercury mineralization asso-ciated with precious metal districts, (Bodie, California being a type example), and this associ-ation prompted the development of a hypothetical model. Subsequent exploration activities were directed towards the examination of mercury mines and prospects as potential targets for gold deposits. The model envisioned hot spring deposits (sinter) containing mercury mineralization at the surface with anomalous gold values grading downward into significant ore grade gold values.

Jan 1, 1990

By B. C. Scott

Every year more and more mining companies are entering joint ventures to look for minerals. Large companies join large companies, small companies join small companies, and large companies join small companies. Mining companies join oil companies, chemical companies, machinery companies, and companies with no other connection to the minerals business. And well they might, for here is a way for both minerals-oriented companies and those that have no background or knowledge of the minerals business to get actively involved in an outwardly-attractive but high-risk enterprise with the chance to participate in a lucrative minerals find. Thus, for reasons beyond those normally associated with joint ventures in many other fields, corporations, companies, groups, and even individuals are looking to joint exploration ventures as the answer to all problems of getting into or staying in mining.

Jan 1, 1972

By Brian E. McGee

The Federal Coal Management Program represents the culmination of several years of effort by the Department of the Interior (001) to reformulate the manner in which coal owned by the United States is leased and developed. These efforts began in 1970 with a study by the Bureau of Land Management (BLM), which indicated that unless drastic changes were made in. the federal coal leasing procedures, federal coal lands would be leased almost for the asking while production of coal from those lands had been decreasing. Consequently, informal action was taken in 1971, which resulted in no further leasing being authorized until February, 1973. At that time, a formal moratorium on most coal leasing was established, with exceptions granted only for leases needed to satisfy short-term needs such as maintaining existing mines or supplying reserves for new contracts in the immediate future. This leasing policy embodied a long term objective of developing an entirely new planning system for federal coal leasing, as well as to schedule the preparation of a programmatic impact statement for this new system. As a result of the 1973 moratorium and the ensuing application of short-term criteria, only 10 federal coal leases (covering approximately 30,177 acres) were issued from February, 1973, through January l, 1976.

Jan 1, 1982

By M. R. Rosen

A technique is presented for simple characterization of the performance of flocculents in various mining applications. The method utilizes three key parameters obtained from raw settling data and combines them into a single athematical parameter called the desirability coefficient. The first two parameters are the timesrequired for the slurry-supernatant interface -to fall to two selected fractions of the starting height, and the third is the clarity of the supernatant liquid. The relative values of the three parameters may be assigned different weights in order to make them correspond with laboratory and field performance requirements of a particular industry. Provision is also made of an, internal comparison of test flocculant data with that of a control.

Jan 1, 1980

By Hamed Ardalan, Mohamed Ashour

"CHAPTER 1INTRODUCTIONThe use of piles to stabilize active landslides or to prevent instability in currently stable slopes has become one of the most important innovative slope reinforcement techniques over the last few decades. Piles have been used successfully in many situations in order to stabilize slopes or to improve slope stability, and numerous methods have been developed for the analysis of piled slopes (Ito et al., 1981; Poulos, 1995; Chen and Poulos, 1997; Zeng and Liang, 2002; Won et al., 2005).The piles used in slope stabilization are usually subjected to lateral force through horizontal movements of the surrounding soil; hence they are considered to be passive piles. The interaction behavior between the piles and the soil is a complicated phenomenon due to its 3-dimensional nature and can be influenced by many factors, such as the characteristics of deformation and the strength parameters of both the pile and the soil. The interaction among piles installed in a slope is complex and depends on the pile and soil strength and stiffness properties, the length of the pile that is embedded in unstable (sliding) and stable soil layers, and the center-to-center pile spacing (S) in a row. Furthermore, the earth pressures applied to the piles are highly dependent upon the relative movement of the soil and the piles."

Jan 1, 2013

By Mallett CW, Hammond RL

Geological maps of the Pacific Rim recently published by the Circum-Pacific Council for Energy and Mineral Resources have provided a useful perspective from which to view modern plate interaction and the evolution of modern fold belts. An important lesson from any study of modern plate interaction is that of the normality of change. The chaotic is more usual than the simple. Present day convergent margins with mixed characteristics are measures of this chaos. Indeed, the character of less than one third of the present length of the Pacific Rim can be ascribed to conventional models of plate interaction. Another lesson is that of the great mobility of oceanic crust. Enormous areas of the Pacific may not be represented in future fold belts developed at convergent boundaries unless normal consumption processes are disrupted, and even then only by linear zones a few kilometres wide. The axes of divergent boundaries creating Pacific Ocean crust have been equally mobile, with new spreading sites taking over from older sites through time. Divergent boundaries, whether active or inactive, consist of oceanic crust, and may be wholly consumed at collision sites with convergent boundaries. Their only potential contributions to fold belt evolution are transforms and magmatic activity. It is this transform component that can provide us with a mechanism to explain the apparent contradiction of both compressional and extensional features occurring together in a developing fold belt. Reconstructions for the SW Pacific are used to demonstrate that the fold belts under construction during the last 4% (Jurassic- Recent) of geologic time have involved interaction between convergent, divergent, and transform boundaries. In the last 15% of earth history (Late Proterozoic-Recent), many enigmatic features of the geologic landscape in Eastern

Jan 1, 1987

By R. Stefanko

Rock bolting as a method of support continues to increase with applications in many other industries in addition to mining. Nevertheless, with nearly 55,000,000 roof bolts installed in coal mines alone last year, this remains as the single greatest use. While bolts have frequently supported ground where conventional timbering could not, there are relatively few design criteria; and trial-and-error procedures prevail. Furthermore, development of suitable instrumentation that is simple to install and readout, sensitive, durable, reliable, safe and economical in evaluating the effectiveness of a bolt over long periods of time lags behind. Therefore, the pull test continues to be the most popular method of evaluating the applicability of a certain type of roof bolt under specific installation conditions. At Penn State in the Department of Mining, research has been conducted for a number of years to measure bleedoff in carefully controlled laboratory experiments as well as in underground investigations.1,2,3,4 Unfortunately, most of the instrumentation developed has been primarily suitable only for research purposes, not possessing all of the aforementioned characteristics desirable for routine underground use. Other groups also have met with restricted success. Therefore, while relatively crude, the torque wrench continues to remain as the most widely used load measuring device. While both field and laboratory tests continue to be conducted, analytical analyses are attempted to discover the more important design parameters in order that more efficient anchorage might be devised.

Jan 1, 1969

By David C. Oyler, Dennis R. Dolinar, Christopher Mark, Craig S. Compton

Fully-grouted roof bolts comprise more than 80% of the primary roof supports used in U.S. coal mines. However, nearly 1,500 MSHA reportable, non-injury roof falls occur each year, and most of these are attributable to failure of the roof bolt system. Anchorage failure is one failure mechanism for fully-grouted bolts. As roof deformation works its way upward, the bolts can become heavily loaded near their upper ends. If the applied load exceeds the anchorage, the bolts will simply pull out. Research dating back 30 yrs indicates that this type of anchorage failure is most likely when the roof rock is weak, just where roof support is most critical. In soft shale or coal roof, the small amount of data available in the literature indicates that 20-30 in of resin anchorage may be required to achieve the full capacity of the bolt. In other words, the “full resistance zone” of a 60 in bolt may actually be just 30-40 in. Despite its potential importance, there is no widely accepted anchorage test for fully grouted bolts. Standard pull tests have sometimes been employed, but they provide no information on the anchorage near the top of the bolt. An alternative, first described more than 25 yrs ago in the U.S., is the short-encapsulation pull test (SEPT). With this test, the bolt is installed with only a short (1 ft or less) tube of resin. In recent years variations of this test have become international standards. v

By Chris Mark

Fully-grouted roof bolts comprise more than 80% of the primary roof supports used in U.S. coal mines. However, nearly 1,500 MSHA reportable, non-injury roof falls occur each year, and most of these are attributable to failure of the roof bolt system. Anchorage failure is one failure mechanism for fully-grouted bolts. As roof deformation works its way upward, the bolts can become heavily loaded near their upper ends, If the applied load exceeds the anchorage, the bolts will simply pull out. Research dating back 30 yrs indicates that this type of anchorage failure is most likely when the roof rock is weak, just where roof support is most critical. In soft shale or coal roof, the small amount of data available in the literature indicates that 20-30 in of resin anchorage may be required to achieve the full capacity of the bolt. In other words, the "full resistance zone" of a 60 in bolt may actually be just 30-40 in. Despite its potential importance, there is no widely accepted anchorage test for fully grouted bolts. Standard pull tests have sometimes been employed, but they provide no information on the anchorage near the top of the bolt. An alternative, first described more than 25 yrs ago in the U.S., is the short-encapsulation pull test (SEPT). With this test, the bolt is installed with only a short (1 ft or less) tube of resin. In recent years variations of this test have become international standards. This paper describes recent studies using short encapsulation pull tests in the U.S. Tests were conducted in the National Institute for Occupational Safety and Health (NIOSH) Safety Research Coal Mine at Bruceton and at underground mines in Pennsylvania and West Virginia. The study found that the SEPT can be used to make a simple evaluation of resin bolt anchorage. Suggested procedures for conducting SEPT are included. The study also confirmed that poor anchorage can be an issue, particularly where the roof rock is very weak. Some simple techniques for improving anchorage, and thereby the effectiveness of fully grouted bolts, are discussed.

Jan 1, 2002

By Claudio Asioli

"The project’s goal was to construct the Al Ghazala Intercontinental, a multi-use development in the bay area of Tripoli overlooking the Mediterranean Sea. The site of the project is located approximately 500 ft (150 m) from the Mediterranean coast, near the Al Ghazala roundabout in the town center of Tripoli, Libya. The investor of the project was Magna Properties Group, Ltd. – Libya, the main contractor was Man Enterprise S.A.L., and the design and construction management was performed by Dar Al-Handasah Engineering. Trevi S.p.A. was contracted to perform the design and construction of the anchored diaphragm walls and dewatering systems for the excavation of a two-level basement car park, which extends across the full footprint of the site.The site was approximately 640 ft by 230 ft (195 m by 70 m) in plan and nearly flat. The groundwater level typically varies from about 11 ft to 23 ft (3.4 m to 7.0 m) above mean sea level. To construct the required raft foundation, it was necessary to excavate the area down to El. -15.7 ft to -26.3 ft (-4.8 m to -8.0 m), which resulted in an excavation depth ranging from about 27 ft to 39 ft (8.3 m to 12.0 m) below the existing ground surface.Subsurface ConditionsThe subsurface site investigation was performed in three phases by Al-Tamier Engineering Consulting Bureau. During Phase 1, a preliminary investigation was undertaken during the early stages of the project to obtain information about the general stratigraphy and groundwater level at the site. Phase 2 was performed to obtain subsurface information and design parameters, and Phase 3 was performed as a supplementary ground investigation to investigate unexpected ground conditions identified during Phase 2. In total, 14 boreholes were drilled to depths ranging from about 80 ft to 180 ft (24 to 55 m). The generalized subsurface profile is quite heterogeneous, and is predominantly composed of sand with silt and gravel that is underlain by limestone, calcarenite and claystone"

Jan 1, 2017

By Claudio Asioli

"The project’s goal was to construct the Al Ghazala Intercontinental, a multi-use development in the bay area of Tripoli overlooking the Mediterranean Sea. The site of the project is located approximately 500 ft (150 m) from the Mediterranean coast, near the Al Ghazala roundabout in the town center of Tripoli, Libya. The investor of the project was Magna Properties Group, Ltd. – Libya, the main contractor was Man Enterprise S.A.L., and the design and construction management was performed by Dar Al-Handasah Engineering. Trevi S.p.A. was contracted to perform the design and construction of the anchored diaphragm walls and dewatering systems for the excavation of a two-level basement car park, which extends across the full footprint of the site.The site was approximately 640 ft by 230 ft (195 m by 70 m) in plan and nearly flat. The groundwater level typically varies from about 11 ft to 23 ft (3.4 m to 7.0 m) above mean sea level. To construct the required raft foundation, it was necessary to excavate the area down to El. -15.7 ft to -26.3 ft (-4.8 m to -8.0 m), which resulted in an excavation depth ranging from about 27 ft to 39 ft (8.3 m to 12.0 m) below the existing ground surface. Subsurface ConditionsThe subsurface site investigation was performed in three phases by Al-Tamier Engineering Consulting Bureau. During Phase 1, a preliminary investigation was undertaken during the early stages of the project to obtain information about the general stratigraphy and groundwater level at the site. Phase 2 was performed to obtain subsurface information and design parameters, and Phase 3 was performed as a supplementary ground investigation to investigate unexpected ground conditions identified during Phase 2. In total, 14 boreholes were drilled to depths ranging from about 80 ft to 180 ft (24 to 55 m). The generalized subsurface profile is quite heterogeneous, and is predominantly composed of sand with silt and gravel that is underlain by limestone, calcarenite and claystone."

Jan 1, 2017

By Chu E. Ho, Paul Napoli

A new waterfront park was developed on Long Island in close proximity to the East River and Newtown Creek. The existing ground consisted of fill over soft organic clay, medium dense silty sand, glacial till and schist bedrock. The ground was initially raised to preload the underlying soft soils to stabilize the ground in preparation for site development. The ground was subsequently cut down to temporary grades for installation of foundation piles for the overlook structures and construction of reinforced concrete cantilever retaining walls forming pathways located adjacent to the water bodies. The retaining walls were located in two rows at different elevations along the sides of a steep embankment. Where the pathways converge, some of the walls were too close to each other, and were redesigned as a combined U-wall with a common base slab. The individual retaining walls were designed for adequate bearing, sliding and overturning resistance. Ground anchors were installed to enhance global stability of the retaining walls. This paper presents the design considerations for the retaining walls for various loading conditions, and evaluation of the trial and proof tests for the anchors. INTRODUCTION The New York City Master Plan included the transformation of an approximately 30-acre parcel of land in Long Island City, Queens, New York from a former manufacturing zone into a residential, commercial and recreational zone for middle-income community. The site was located at Hunters Point South along the eastern shoreline of the East River and Newtown Creek (Figure 1). The development included low to high- rise residential buildings, a public school, and retail structures. Open spaces were provided along the East River and Newtown Creek waterfronts in the form of a continuous park providing for recreational and community-related activities. Waterfront structures included small park buildings, walkways and viewing platforms. The shoreline was surrounded by revetments as part of the flood mitigation strategy. The project involved extensive site re-grading and several retaining walls were constructed. The earthwork volume amounted to approximately 47,000 cubic yard of imported fill and 93,000 cubic yard of cut. The exposed height of the retaining walls ranged from 3 to 15 feet. This paper focuses on the design and construction of the retaining walls for the project.

Jan 1, 2019

By Seth L. Pearlman

A major excavation support case history for the Eastern approach to the Third Harbor Tunnel (THT) in Boston, MA is described, which uses an anchored Soil Mixed Wall (SMW). Both general and project specific information is provided regarding the design and construction of SMW walls. In addition, conclusions are presented that discuss the suitability of this particular application and other possible variations.

Jan 1, 1993

By Marco D. Boscardin, Benjamin H. MacKinney, Kenneth R. Allard, Kenneth A. Pidgeon, Adriane G. Boscardin

This paper presents a case history for a unique application of a system of vertical micropiles with horizontal soil nail bracing and shotcrete facing for underpinning. The system was used to support and protect an existing 2-story hospital building during demolition and renovation. The goal was to limit building movements and have the building remain in use during construction of an abutting addition. Soils at the site consisted of clean, loose to dense, sand and gravel. The original underpinning design was revised after the initial excavation revealed unsuitable soil conditions for traditional underpinning pits. An alternative system consisting of vertical micropiles (hollow bars) through the footing, combined with shotcrete and soil nails was proposed, accepted by the owner, and successfully constructed. Excavation depths were up to 15 feet (4.6 m) below the existing footings. Wall movements were monitored at regular, horizontal and vertical intervals along the hospital wall, and less than 0.6 inches (15 mm) of settlement and 0.1 inches (3 mm) of horizontal displacement throughout underpinning and construction were reported. The challenges with the original proposed support of excavation design and other alternative approaches considered will also be discussed.

Oct 1, 2022