Search Documents

By Helvio Pessanha Guimarães Santafé Jr.

The coir fiber extracted from the husk of the coconut has been extensively used as polymer composite reinforcement in a variety of industrial applications ranging from civil construction to automobile seat cushions. The hydrophilic coir fiber does not act as an effective reinforcement owing to its low interfacial strength with hydrophobic polymers. As a consequence, coir fiber composites display relatively low mechanical strength. The objective of this work was to investigate the effect of an acetylation treatment of the coir fiber surface on the mechanical behavior of epoxy composites with amounts of fibers up to 30% in volume. Coir fibers were immersed in an acid solution of acetic anhydride for one hour, washed and dried, before mixing with DGEBA/TETA epoxy to fabricate the composites. Flexural mechanical properties were obtained by bend tests. The results showed significant differences to similar composites with alkali treated coir fibers that have been previously investigated.

Jan 1, 2010

By Sergio N. Monteiro

Polymeric matrix composites reinforced with coir fibers are being used in many industrial applications such as automobile interior panels and cushions. These composites have relatively low mechanical strength due to the weak fiber/matrix interface. The objective of the present work was to investigate the effect of a surface alkali treatment of the curaua fiber on the mechanical behavior of polyester composites with different amounts of these fibers. The treatment, also known as mercerization, was performed with distinct concentrations, 0.1 and 10% of NaOH at 1 min and 1 hour, before incorporation of the coir fibers into the polyester composite. The results showed no significant change in comparison to similar untreated coir fiber composites. A microstructure analysis revealed that, in addition to reducing the hydrophilic characteristic of the fiber,the treatment also affects the surface morphology and impairs the fiber/matrix interfacial strength.

Jan 1, 2009

By Manuela Castaneda, Henry A. Colorado

This paper is about the use and stabilization of iron oxide based powders with arsenic contents coming from the purification of water. Cement paste samples with 0.0, 2.5, 10 and 20wt% of waste were fabricated by mixing mechanically all components. There are two main positive impacts of using this waste, first, this waste is produced in large amounts worldwide, and therefore the stabilization has a significant impact for the environment. Second, the waste can be used as an admixture and filler for cement, and therefore reduce the amount of cement in the concrete, which has a major impact in the CO2 footprint since cement industry produces a lot of this gas. Compressive strength and density tests were tested after 28 days. Microstructure was analyzed with scanning electron microscopy and x-ray diffraction. Results show that compressive strengths greater than 20 MPa were obtained and the samples had calcite, portlandite and ettringite phases.

Mar 1, 2018

By Ch. Schroeder, F. Collin, R. Charlier, Y. J. Cui

The paper proposes two numerical models ot the mechanical behaviour of chalk. First, an elasto-plastic constitutive law reproduces the different plastic mechanisms of the chalk and the influence of pore fluids by introducing the concept of suction. Secondly, a model able to reproduce time dependence behaviour. Eventually, the paper gives a simulation of an academic reservoir during depletion and waterflooding phase. Der Artikel stellt zwei numerische Modelle des mechanischen Verhaltens der Kreide vor. Das erste ist ein elasto-plastisches Modell, das verschiedene plastische Mechanismen der Kreide und den Einfluss von Porenflüssigkeit, unter dem Begriff der Suktion, reproduziert. Das zweite Modell berücksichtigt darüberhinaus das zeitabhängige Verhalten. Schliesslich zeigt die Veröffentlichung eine Simulation einer theoretischen Lagerstätte während der Entleerung und der Wasserinjektion. L'article propose deux modèles numériques du comportement mécanique de la craie. Le premier est une loi élasto-plastique qui reproduit les différents mécanismes plastiques de la craie et l'influence du fluide interstitiel par l'introduction de la notion de succion. Le second est un modèle prenant en compte les effets différés. Enfin, l'article présente une simulation d'un réservoir académique durant les phases de déplétion et d'injection d'eau.

Jan 1, 2003

By M .. Hori, H. Onishi, Y. Goda

The split-lining structure was newly developed for the air-tight lining of the underground compressed air storage cavern. This structure consists of separated reinforced concrete (RC) segments and air-tight membrane. It is most important for the Compressed Air Energy Storage Gas Turbine (CAES-G/T) system to develop the economical lining. In order to verify the applicability of split-lining structure, CAES-G/T pilot plant was constructed and operated for 6 months. We confirmed the practical usefulness and safety of this system through the operation. This paper presents the mechanical behaviour of surrounding rock mass and the lining structure observed through the operation of CAES-G/T pilot plant. Nous avons mis au point une structure de revêtement modulaire pour le revêtement des cavernes souterraines hermétiques à pression. Ce revêtement est composé de segments de béton armé et de membranes hermétiques. Il était très important, pour le CAES-G/T (Compressed Air Energy Storage Gas Turbine), de développer un revêtement économique. Afin de vérifier l’aptitude d’application de notre revêtement modulaire, nous avons construit un système pilote CAES-G/T et nous avons effectué des essais de fonctionnement pendant six mois. Ces essais nous ont permis de confirmer l’utilité et la sécurité du système. A travers le présent rapport, nous rendons compte de la structure de ce nouveau type de revêtement et du comportement mécanique de la masse rocheuse environnante que nous avons pu observer au cours desdits essais. Als luftdichter Druckbehälter wurde eine gegliederte Belagsstruktur für tief unterirdisch liegende Felshöhlungen entwickelt. Diese Struktur ist aus Stahlbetonabdeckung und luftdichter Plane aufgebaut. Bei der Entwicklung des Pressluftgasturbinen – Stromerzeugungssystems (CAES-G/T) war es die wichtigste Aufgabe, einen wirtschaftlichen Belag zu entwickeln. Deswegen wurde zum Nachweis der Effektivität der gegliederten Belagsstruktur eine Pilotanlage errichtet und 6 Monate lang betrieben. Durch den Betrieb konnten wir die Praktikabilität und Sicherheit des Systems bestätigen. Dieser Aufsatz ist ein Bericht über das Verhalten der durch Betrieb der CAES-G/T Pilotanlage beobachteten Belagsstruktur und umliegenden Felsmasse.

Jan 1, 2003

By J. F. Liu, L. Chen, C. P. Wang

"Calcite-cemented joints abound in the rock masses of Beishan area, which is the most potential area for the high-level radioactive waste (HLW) disposal of China. The mechanical properties of Beishan granite containing a calcite-cemented joint with a dip angle of 82° was investigated under uniaxial compression and the acoustic emission (AE) characteristics were also studied in this paper. Compared to intact granite, the calcite-cemented joint caused a decrease more than 50% in uniaxial compressive strength and a decrease more than 90% in shear strength. The Young’s modulus was also decreased, while the circumferential deformation of jointed granite was sharply increased. The AE monitoring system successfully recorded the process of micro-crack development and the results indicated that the risk of rock-burst could be reduced due to the appearance of calcite-cemented joint.INTRODUCTIONThe properties of jointed rocks differ considerably from that of intact rock. Due to the difficulties in specimen preparation, analogue experiments with artificially prefabricated fractures are often used to study the mechanical behavior of jointed rock (Chen et al. 2012; Kulatilake et al. 2001; Singh et al. 2001). However, natural joints are not quite similar to the artificial fractures and it is necessary to investigate the mechanical behavior of jointed rocks. Xie et al. 2011 studied the mechanical properties of marbles with natural joints by uniaxial compression tests and found that the uniaxial compressive strength of jointed rock is greatly decreased. With the unaxial compression tests, Jacobsson 2005, 2007 tested the intact and jointed granites, which were taken from the potential site for high-level radioactive waste (HLW) disposal of Sweden. However, no significant difference in strength or modulus was found. The above research results are inconsistent and it indicates the complexity of the mechanical properties of natural joints."

Jan 1, 2015

By J. M. N. P. C. Teles, Venda Oliveira P. J., Correia A. A. S.

"AbstractA laboratory work was performed to study the mechanical behavior of a Portuguese soft soil chemically stabilized with binders and reinforced with metallic fibers when subjected to tensile stresses. To this end and in order to compare the tensile strength results done by two different tests, there were conducted two types of experimental tests: Tensile Split Strength Tests (TS) and Direct Tensile Strength Tests (T). The samples tested had the same binder quantity and different fiber contents, which allowed the characterization of the tensile behavior of the stabilized and reinforced soil, as well as the definition of the best fiber content. Results show that the binder is the main parameter controlling the behavior of the stabilized and reinforced soil until failure, while the influence of the fibers is noticed mainly at the post-failure behavior. The comparison between the tensile strength done by T and TS tests shows that the tensile split test can be used to estimate the tensile strength, although its results are lower than those obtained by the direct tensile tests in general.IntroductionDue to its poor mechanical characteristics, the construction on soft soils presents difficulties that require the use of soil improvement techniques such as chemical stabilization. However, even when mixed with binders, the tensile strength of the stabilized soil is poor, requiring, in certain cases, the use of expensive steel reinforcement or metallic beams, with obvious impact on the final cost of the work. Thus, for the cases where the tensile strength is a design requirement, the soil stabilization should be design with another element, whose primary role is to give tensile strength to the improved soil (Teles 2013).To fill the lack of published studies focused on soft soils both chemically stabilized and reinforced with metallic fibers, the present research aims to analyze the behavior of the improved soil when subjected to tensile stresses. To support the research there were conducted direct tensile tests (T) to directly measure the tensile strength of the samples and tensile split tests (TS) or Brazilian tests to obtain it indirectly. The samples tested had the same binder quantity but five different fiber contents in order to study the influence of the fibers in the improved soil behavior. In addition, a comparison between the results of both tests was made."

Jan 1, 2014

By H. W. Hitzrot

Introduction Mechanical classifiers consist of a settling tank with parallel sides and a sloping bottom equipped with a mechanism which continuously agitates the pulp and removes the settled solids. The functions served by mechanical classifiers include the following: (1) allow the particles larger than the desired size to settle in the tank and provide an overflow product with a minimum of oversize particles, (2) produce an overflow product of sufficiently high solids content to meet the requirements of the subsequent processing steps, (3) agitate the pulp and permit separation of the entrapped undersize particles so they can report in the overflow product, and (4) drain and remove the underflow solids from the settling pool. Various types of mechanisms have been used to agitate the pulp and remove the settled solids, which include: (I) endless belt and chain drags, (2) reciprocating rakes, (3) helical flights mounted on a rotating shaft which extends through the settling pool, (4) helical flights inside of a rotating drum which contains the classifier pool, (5) troughed conveyor belts forming the settling pool in the concave curve of the belt closely following the tail pulley, and (6) low-speed impellers agitating the underflow settled in the apex of cone-type mechanical classifiers.23 The principal use of mechanical classifiers has been in closed¬-circuit wet grinding; however, this application has been widely displaced over the past few decades by the hydrocyclone. The hydrocyclone installation, including its feed pump, offers lower capital costs and requires less floor space. Nominally it produces an overflow prod¬uct of higher solids content, compared with a mechanical classifier, for comparable classification size up to 400µm (35 mesh). However, these advantages of the hydrocyclone are being gained at the sacrifice of some of the advantages of the mechanical classifier. The mechanical classifier requires less power and has lower maintenance costs than the hydrocyclone and its feed pump. The underflow product from the mechanical classifier can have a higher solids content and contain less entrapped undersize particles than the comparable product from the hydrocyclone. Consequently, it is capable of operating at a higher classification efficiency. A reduced circulating load24, 25 results under these conditions in a closed-circuit grinding application. Other applications for mechanical classifiers include desliming, dewatering, and washing operations. Sand-slime separation may be achieved using one or more stages of mechanical classifiers. Typical applications would include washing and deslimining of concrete aggre¬gate or sand; glass sand; abrasives; oyster shells; phosphate rock; iron, nickel, and chromium ores; alumina; zeolites; solar salt; and precipitates from chemical processing. As an example for the latter, Bitzer26 recommended the use of mechanical classifiers for countercur¬rent cementation-in-pulp of copper from the leach liquor. Similarly, mechanical classifiers are used in uranium processing27 for separation of the barren sands from the pregnant leach solution. Depending on the particle size and the effectiveness of the sand¬slime separation, the sand product from mechanical classifiers may be drained to solids content approaching 84%. Thus, mechanical classifiers are frequently used as dewatering equipment for various applications, such as: 1) Make a product having suitable solids content for subsequent transport by belt conveyor. 2) Provide a drained product to reduce cost of drying. 3) Provide a drained, washed, heavy sand product for return to the circuit. 4) Recover fine values from dilute plant effluents from coal, sand, phosphate-rock, and iron-ore washing plants and from steel-mill flue¬dust scrubbers. 5) Drain residual reagents of a preceding process stage prior to conditioning with reagents of different characteristics, e.g., cationic¬anionic flotation of phosphate rock, iron ore, etc. Design and Operating Features The proper selection of mechanical classification equipment re¬quires that the properties of the solids and liquid are adequately de¬fined. The following descriptive information regarding the solids is desired: feed rate, chemical and physical composition, density, tem¬perature, size analysis, and desired separation size. For the liquid used, the following data would be needed: feed rate, density, viscosity, pH, and temperature. Settling Area. The pool area required to permit a particle larger than the separation size to settle depends on the density and shape of the particle and on the density and viscosity of the pulp within the classifier pool. These criteria of the solids and pulp determine the settling rate which, in turn, determines the settling area required. Determination of the settling rate by long-tube batch tests can be used to calculate the settling area. A theoretical approach for estimat¬ing the settling area requirements is discussed in Chapter 1, Classifica¬tion Theory. This procedure can be used when neither test data nor empirical data from similar operations are available. Data on settling-area requirements and settling rates have been compiled by the manufacturers of mechanical classifiers. The approxi¬mate settling area required for a particular separation size can be estimated by using the curve shown in Fig. 65. This curve applies for closed-circuit grinding applications. For dilute velocity classification in open circuit, desliming, the length of the overflow weir, W, multiplied by the weir's mean distance from the feed opening, E, is used as the design criterion, instead of the settling area, in sizing the classifier. The area requirements, W X E, for dilute velocity classification can be expressed in terms of volumetric flow, Q, and settling rate, Rs, as follows: W x E = Q/(18.06 Rs) where W and E are feet, Q is gallons per minute, and Rs is inches per second. Overflow Weir. The hydraulic head, and thus the velocity at which the overflow crests the overflow weir, is one of the factors controlling the particle size of classification. Consequently, the length of the overflow weir must be designed to provide the overflow velocity which allows the particles larger than the desired size of classification to settle in the working area of the pool. Obtaining the necessary

Jan 1, 1985

The problem of separating the constituents of a mixed gas has assumed increasing importance to chemical technology during the last several decades. Metallurgical practice, dealing mostly with the application of gases as fuel, such as for the oxidation or reduction of ores, has not often confronted an important need for such separations. If theory occasionally has indicated advantages in the use of purified or separated gases, as for example the "dry" blast for the iron furnace or oxygen-enriched blast for a variety of smelting operations, the economics of the proposals has not often been satisfactory. It has seemed evident that the practice of the chemical plant was too expensive with regard to installation or material costs, or both, for the needs of the basic smelting industries and indeed was applicable commercially to metallurgical purposes only when the metals in question were especially valuable or pure. This bulletin deals with a new mechanical means of attacking the problem of separation. Although it is improbable that any one type of separation could hope to find universal application, the method described is to be regarded as an alternative to conventional means that has attractive possibilities in certain instances. It extends the number of methods previously available by one that has not before been applied commercially and that utilizes a well-known property of gases that never has received effective technologic attention.

Jan 1, 1940

By Franco de Castro Bubani

Cu-base alloys (Cu-Zn-Al, Cu-Al-Be, Cu-Al-Ni), depending on their composition, have martensitic transformations that can be thermally or mechanically induced between a metastable structure called austenite and one or more metastable structures called martensites. In single crystals, depending on the specific composition of the alloy and the crystallographic orientation of the tensile axis, martensite-martensite transformations can be mechanically induced. The hysteresis associated to these martensite-martensite transitions is usually much greater than the one associated to the austenite-martensite transformation. Thus, martensite-martensite transitions are potential candidates for energy dissipation in a mechanical damper. Possible applications that would benefit from high hysteresis include seismic damping devices, dampers for satellites and the aerospace industry, defense and others. We present pseudoelastic cycling results of alloys submitted to different thermal treatments. Our conclusions highlight the fact that, under certain conditions, Cu-base alloys deliver better damping performance than commercially available SMAs and even the new Fe-base SMAs.

Aug 7, 2018

By J. P. Matoney, E. J. Sandy, D. A. Dahlstorm

INTRODUCTION Before an understandable discussion concerning coal dewatering processes can be initiated, it is necessary to define some terms of usage. The many different meanings and interpretations of terms preclude development of standard definitions so the terms defined in this chapter should be regarded primarily as working terms intended to facilitate communication.

Jan 1, 1979

By H. Kohno

The Onahama No.3 tankhouse started commercial operation in early 1973, with the capacity of 8,500 metric tons per month. When the No.3 tankhouse was constructed, the starter sheet stripping section was rebuilt at the No.2 tankhouse and electrolyte purification section was expanded. The previous AIME paper in 1976 described the design principles of the No.3 tankhouse and its layout, This paper describes the starter sheet stripping machine in the No.2 tankhouse and the electrodes handling system in the No.3 tankhouse and all these equipments were developed for the operation of the No.3 tankhouse. A Hazelette continuous casting machine was also introduced in order to cast thin anodes with accurate shape. Owing to the adoption of thin anodes, gold, silver and copper inventory is reduced by 40%. Jumbo tanks and newly developed mechanical equipments were adopted and no work on cells during pulling up operation was achieved. Using thin anodes with accurate shape, inspection work was completely abolished while maintaining high current efficiency and high cathode quality. Labor cost was reduced by 70% and only six operaters can produce? 8,500 metric tons of cathodes per month. The same new electrolysis process is appreciated and has been used as a newly built independent tankhouse by Kidd Creek Mines Ltd., in Canada in 1981 with excellent results

Jan 1, 1987

By Inoue T, Takahashi N

To construct the accessing railroad line to the northern portal of Seikan Undersea Tunnel, nine tunnels amounting 7.4km in their total length were excavated through soft mudstones of young- er tertiary era with use of smaller-sized mechanic al excavators. Rocks were classified in four classes to which the tunnel support was designed respectively. Of several combinations of driving equipments stu- died comparatively, the method using the mechani- cal excavators was estimated to be the best choi- ce. The efficiency of the excavator was traced in every construction section and the data colle- cted was reviewed numerically. The result showed that the efficiency of the excavator dropped wh- ere the rocks were as hard as over 200kg/crif for compressive strength. And a few technigues in tunnelling i.e. contr- olling dusts in shotcreting, lattice arch, evaluati- ng measured deformations were tested and review- ed too.

Jan 1, 1987

By J. Pontt

Gearless mill drives (GMD) offer high performance for torque and speed control for grinding mills and have been applied successfully in modern concentrators for wet grinding with mill diameters from 34 to 40-feet. It is considered a mature technology. However, recently, some large GMD?s have presented unexpected failures in stator and rotor subsystems. The phenomena involved in such failures has shown a complex nature and surprised users and manufacturers. The manifestation of such failures has been observed as mechanical damages to certain components of ring motors. This paper presents a discussion on the electromagnetic forces that can generate stresses in the electrical ring motor that can produce failures and outages. Guidelines for further research and contributions to improved reliability of GMD?s are proposed.

Jan 1, 2012

By Hugo Julien

According to OSHA 29 CFR Part 1910.119 (Process safety management of highly hazardous chemicals), Canadian Provincial Safety Standard Acts or Federal laws, the owner of stationary equipment (Boilers, stacks, piping, pressure vessel, etc.) should follow a complete inspection plan and follow an Integrity Operating Windows (IOW’s) adapted for each of them. Some important variables shall be included in the inspection plan such as specific damage mechanisms versus alloy used in the original design, process conditions, etc. Some North American’s standards exist, like the one listed in ASME PTB-2-2009, to help owner to create such inspection program. The new API RP 584, Integrity Operating Windows (IOW’s) can guide Mining & Metals owners to find out their specific IOW’s. Inspection frequencies are often described in the Jurisdiction Safety Acts such as the British Columbia B.C. Reg. 104/2004, etc. but often left in the owner representative responsibility (Bill C-21, federal Act to amend the Canadian Human Rights Act). Every deficiency should be repaired according to recognized Codes such as ASME PCC-2, etc.. If flaws not conforming to the original Code of construction are found, this article will introduce the Fitness-For- Service assessment principles to be able to accept it without any repairs.

Jan 1, 2014

By Wm. H. Woodhead

Improved methods of mining have accompanied the introduction of mechanical loading, of which there are a great many varieties, but this multiplicity of mining brings new problems and greatly increases the importance of managing over a few years ago. Few mines operating today have been opened with the intention of mechanizing throughout. The problem of mechanization is to change over a mine heretofore operated by hand methods and to select machinery that will fit the old system with the least number of changes, the aim being not to disrupt or to completely change the original plan. The organization of mechanical and electrical forces is a problem in mechanical loading, and each individual mine presents its own problems. Plans which may succeed in one mine may fail in another and upon the management rests the responsibility of deciding the best method in each case.

Jan 1, 1930

By S. W. Farnham

Those who remember the years of patient effort and the slow results obtained in the first introduction of electrical coal cutters and locomotives will, I think, admit that mechanical loading of coal is unquestionably being established at a much more rapid rate than any previous application of machinery to reduce manual labor in mines. There are many operators who consider the progress of the loaders today as slow, but considering the number of years it took to thoroughly establish electrical coal cutters and locomotives, and comparing it with the short time that the mechanical loader has been on the market, and the results that have been obtained today, they will admit, I think, that the progress of the latter is much more rapid. It is about 35 years since the advent of the electrical coal cutter and electric locomotive. Their use has brought about these improved conditions, increased tonnage per mine and other features, which are of assistance to the installation of mechanical loaders. The management and the technical staff in practically all of the American mines are trained in the use of electrical machinery and understand its operation, care and maintenance. . There is frequently, a surplus of electrical power and wiring available to take care of the small requirements of the electrical loader. The mechanical loader, therefore, starts today with the ground prepared for it. Those manufacturing companies who have had years of experience in the design and construction of mining machinery, know in a large measure what to incorporate in their designs to make the parts of the new type of machine effectively strong and to operate with efficiency under the severe conditions encountered in mining service. All these advantages greatly assist the success of a new type of machine such as the mechanical loader. In spite of these advantages, however, there are bound to be some failures. All new types of loaders have to be developed. We hear of some that are a success and some that are set aside. The field of application of each type and its limitations first must be determined by actual operation. The earlier loaders had to be changed and improved in design as weaknesses developed. Not all of the new types of coal loaders have been built by mining machinery manufacturers of long experience, and the lack of experience in this line is responsible for some of the early failures. The coal mining company staffs and also those of the loader companies had to learn what the operating factors were that made mechanical loading a success. The difference in results obtained by loaders in different properties under similar physical conditions indicates that the mine management is a very large, if not the major factor, affecting the efficiency of mechanical loading. Many articles have been written on the question of loading. The subject has been quite fully discussed at recent coal meetings and in the technical press. It is not always as easy or simple a matter to form conclusions as may first appear as to one's own particular loading problem. Mechanical loading is a comparatively new art, and many companies while claiming that loaders are quite successful, do not have an accurate line on the actual saving they are affecting. Many of them have only a few of the factors taken into account in their costs. Many loaders have been generally bought without very careful consideration given to all details and except where extremely favorable conditions prevail, failure resulted. When contemplating the installation of mechanical loading, one naturally desires to select the type of loader that will, fit his mining conditions. The things

Jan 1, 1924

By John Kostuik

AT the Sladen-Malartic mine, a number of orebodies have been mined, some by shrinkage and others by open sub-level scopes, from which the ore is handled either through a grizzly system or by mechanical loaders. This paper deals with the comparative costs and relative merits of the two handling arrangements. The facts brought out in this comparison have a bearing on the selection of a proper handling method. The mine is in Fourniere township, northwestern Quebec, about forty miles east of the town of Rouyn. It is served by the Rouyn-Senneterre branch of the Canadian National railways. Two vertical three-compartment shafts give access to the present workings. No. 1 shaft, at which the plant is centralized, is the main hoisting shaft, with five levels to 950 feet. No. 2 shaft, 2,400 feet east of No. 1, is under development, with four levels to 725 feet. At the main shaft, the ore is hand-trammed in 1 1/2 tons cars from the scopes to the stations o:i each level and hoisted in cages to surface at a rope speed of 900 feet per minute. Air-operated tipples are used to dump the ore through grizzlies of 14-inch openings into a surface bin of 150 tons capacity. The ore hoisted at No. 2 shaft is trucked from the headframe bin to the mill. Milling commenced in January, 1938, ar a daily rate of 250 tons. Within two months this rate was increased to the unit's maximum capacity of 325 tons. A second unit to treat a further 325 tons daily was installed in April, 1939. The orebodies mined at No. 1 shaft are parts of a silicified zone at the contact between syenite porphyry and greywacke. The zone is ten co sixty feet wide, strikes easterly, and dips to the south at 55 to 85 degrees. The hanging-wall of the zone is marked, though not precisely, by a strong gouge fault. Locally, the boundary of silicification may be as much as twenty feet either above or below the fault, but for practical mining purposes the fault is the hanging-wall of the ore-zone. The footwall roughly parallels the fault, but as an assay wall it is usually irregular in detail. The ore is dense and hard, a siliceous replacement of both porphyry and greywacke, mineralized with fine disseminated pyrite.

Jan 1, 1941

By A. K. Croteau

"At Craigmont Mines Limited, Merritt, B.C., the mining practice of trackless sub-level caving was started in the latter part of 1966. This type of mining was new to the mine personnel and the mining industry of Canada as a whole. Sub-level caving has presented many old and a number of new problems in maintaining the equipment used in this method. This paper will deal with some of these problems as they affect this particular mining operation. It will be impossible to review all phases of the equipment, but an attempt will be made to cover the most pertinent aspects in maintaining the drilling, mucking and hauling, and auxiliary equipment."

Jan 1, 1970

ATTENTION has recently been directed to the subject of dust production and methods of allaying same in the Broken Hill mines, so that the time would seem opportune for the local branch of the Institute to discuss certain features of an important phase of the health question in connection with underground work. Tests conducted in the Broken Hill South mine and at other mines at Broken Hill have shown that the ordinary operatioils of mining, such as boring, blasting, and shovelling, may be accompanied by the production of considerable dust unless water is judiciously used.In South Africa·dust particles under 5 microns size are regarded as dangerous, becailse they are so small as to be invisible to the naked eye, and wm esc'ape the protections set up by nature in the nose and throat, and thus may be inhaled in large quantity. A micron is 1 25000th part of an inch. This paper contains an account of the work done on the Broken Hill South mine chiefly, though some tests were done on other local mines.An acknowledgment is due to Mr. T. A. Reid, of the Broken Hill South mine, who conducted some of the tests herein mentioned, and under whose supervision most dust counts were made. Numerous dust samples have been taken by means of thekonimeter, an instrument designed by Dr. Kotze, the Government mining engineer of the Union of South Africa, and fully described...

Jan 1, 1921