Search Documents

By N. A. Gokcen, R. A. Dodd

Solubility of nitrogen in liquid iron-manganese system at 1550°C and one atmosphere pressure has been determined by a simple method. Results show that the solubility increases from 0.040 pct for pure iron to 1.41 pct for pure manganese. DETERMINATION of the solubility of gases in volatile metals. and alloys by the well-known Sievertsl method is unreliable. This is particularly true for the Fe-Mn system since Mn vaporizes readily from the alloys containing as little as 2 pct Mn, and, upon condensing on the cooler parts of the apparatus, it absorbs large amounts of nitrogen. Further, the condensing Mn vapor interferes with the usual method of temperature measurements with an optical pyrometer.

Jan 1, 1962

By T. L. Joseph

A study is made of the amount of solution loss necessary to maintain the reducing power of the gas stream in the blast furnace. Curves are presented to show the effect of solution loss, moisture in the blast, and carbon dioxide from the flux on the nitrogen in the THE blast furnace process is based upon the counter flow of gases and solids. As CO, N, and H, flow upward from the combustion zones, oxygen is acquired from the descending charge. In the reduction of iron ore, a portion of CO is converted to CO, and similarly a portion of H, is converted to water vapor. The inert N,, from the air used in combustion, passes through the furnace with little change. Its concentration is, however, decreased by reactions such as direct reduction and solution loss which increase the volume of CO in the gas stream; Similarly the evolution of C02 from the limestone also dilutes the nitrogen. he purpose of this paper is to illustrate an idealized and simplified method of studying furnace processes by following changes in the gas phase between the tuyeres and the stock line. A more specific objective is to evaluate the effect of solution loss upon the CO/CO, ratio in that region of the furnace in which FeO is reduced to metallic iron. This last stage of reduction requires relatively high CO/CO, ratios to exceed the equilibrium requirements. Solution loss or the reaction of COZ with C to produce CO has a pronounced effect upon the ratio of the carbon gases and is necessary to maintain the reducing power of the gas stream if the consumption of coke is low. It will be explained later that indirect reduction followed by solution loss is stoichiometri-cally equivalent to direct reduction. Calculations will be made to show how the composition of the gas in the region of the mantle varies with coke consumption and with different amounts of solution loss. Such calculations show the condi- tions under which gasification of C with oxygen in the charge is needed to maintain the reducing power of the gas. Equilibrium conditions for FeO and the carbon gases will be used to establish a minimum CO/CO, ratio below which reduction will not proceed. The manner in which carbon is gasified in the furnace, at the tuyeres with oxygen in the air or above the tuyeres with oxygen from the charge, will be a basic feature of all calculations. It is hoped that greater interest in the use of top gas as a means of following furnace reactions will be aroused by the calculations and generalized curves which are presented. Bosh Gas Equations Subject to some alteration by the amount of moisture in the blast and by direct reduction, the gas leaving the combustion zones of a blast furnace has a definite composition. Because a relatively small amount of oxygen is acquired from the charge in the bosh and in the crucible, the products of combustion undergo little change until they enter the shaft. Bosh gas is, therefore, essentially the products of combustion of carbon in a deep fuel bed with air. The relative weights and volumes of reacting materials are expressed by the equation: 2~ + 0? + 3.76N, = 2C0 $ 3.76NZ [I] Air Bosh Gas -air = 79% N? = 3.76) 21% 02 Starting with a known mass of C consumed largely by air, Eq 1, but partly by water vapor, Eq 2, the volume and C + H2O = CO $ H? [21 composition of the bosh gas can be calculated and subsequent changes followed as reactions take place at various elevations in the furnace. As shown in

Jan 1, 1952

By D. J. Carney, E. Van Meter, J. J. Oravec

A study was made of combustion-air temperatures and factors affecting air temperatures in the open-hearth regenerative systems. Air-temperature surveys in the regenerative system revealed marked thermal gradients in the air above the checkers. The design of the fantail-uptake region plays a prominent part in increasing the heat recovery of the regenerative system. THE efficiency of the open-hearth regenerative system is one of the most important factors affecting open-hearth performance. Until recently, this factor has not received the attention in the literature given to many other items affecting performance, such as the type of charge, speed of charging, and the mechanical equipment of the open hearth. J. S. Marsh' emphasized the importance of the flame temperature and its dependence upon the combustion-air temperature. By means of measured air temperatures in open-hearth furnaces, data were presented which showed a remarkable degree of correlation between production rate and combustion-air temperature. This correlation was extremely good in view of the numerous factors, other than air temperature, which affect open-hearth production rates. In Marsh's work, a 100°F increase in air temperature reduced the heat time by approximately 45 min. Realizing the importance of combustion-air temperature, it is desirable to know which factors control the regenerative efficiency of the open-hearth furnace. B. M. Larsen recently discussed this subject.' The present paper illustrates a few of the more important items that affect regenerative efficiency and combustion-air temperature. In the latter part of 1951, a study of open-hearth combustion-air temperatures was begun at the South Works of the United States Steel Corp. In the initial work at open-hearth shop X, which produces low carbon steel products, temperatures were measured in the uptake in a manner similar to that used by Marsh' and the results obtained were very similar to the Bethlehem data. When it was decided to expand the study of combustion-air temperatures, open-hearth shop Y was selected because of the greater variety of furnace-design features, types of steel produced, and firing rates used. With the use of aspirating thermocouples, continuous gas analyzers, thermocouple and optical pyrometers, a study was made of: 1—effect of combustion-air temperature on open-hearth production rate, 2—thermal gradients present in various zones of the regenerative system, 3—effect of furnace-design variations on air temperature and heat recovery, 4-—effect of furnace-operating variables on heat recovery, and 5—variation in heat recovery with furnace age during the normal furnace campaign. Data collected on individual heats at 15 min intervals included air-flow rate, firing rate, checker temperature, combustion-air temperature, and furnace pressure. These data were collected on approximately 230 heats of steel. In addition, information was obtained at random on air infiltration and combustion-gas compositions. The data gathered have shown the desirability of closer control of open-hearth firing practices, a need for reducing air infiltration in the uptake zones, and a need for further study of design of checkers and of uptake-fantail areas. Equipment Air is practically a nonradiating medium. Consequently, in the measurement of air temperatures, the principle of heat conduction must be used rather than heat radiation. For this reason, aspirating-type thermocouple pyrometers normally are used to measure air temperatures. With these devices, air

Jan 1, 1956

By G. R. Fitterer

Trends in slag composition in acid open hearth practice, particularly the variation in iron and manganese oxides during refining, are reviewed. A procedure which is currently being used to control the refining reactions is described and partially explained through slag phase diagram considerations. In addition, the ionic nature of these slags is considered and it is proposed that silica combines with the oxide ion and forms a series of complex silicate ions. The effect of basic oxides such as FeO, MnO, and CaO is apparently additive in furnishing the oxide ion for this purpose. IT is now possible to control192 the refining of steel in an acid open hearth furnace to a surprising degree. This control has been brought about through the knowledge and use of several facts and tests. These are: 1—A planned charge analysis based on a knowledge of the type of fuel, the bath depth, etc. 2—Knowledge and control of rate of fuel input as well as its method of atomization, if any. 3—Determination of the slag fluidity. 4—Bath temperatures (use of the Pt-Pt-Rh thermocouple). 5—Periodic determination of carbon content (use of the Carb-analyzer or Carbometer). Through the use of these control methods, a heat may be made to "melt-in" with or without residual manganese and silicon. The rate of refining or carbon elimination may be controlled accurately, and the desired tapping (or "go-ahead") carbon may be approached at a rapid or slow rate according to preference and type of steel being made. Thus operating time may be predetermined and greatly reduced. Further, all of the refining can be done without any ore or other oxidizing additions, and the heat may be brought to the desired tapping temperature simultaneously with the attainment of the desired carbon analysis. This control procedure is being used in most acid plants in the United States today and has been de- scribed.', ' Although the slag metal relations are sufficiently well known to control the heat as stated, yet it is possible to account for only about two-thirds' of the 0, which must have been used for the elimination of the carbon and other metalloids. Phase diagram studies' of the slags, slag weights, the metal particle theory,' ore additions, limestone additions, etc., may all be taken into consideration; yet, the mechanism of oxidation and source of all the oxygen remain to be explained. This paper reviews some of the principles upon which the control methods were based and proposes other possibilities regarding the unexplained phenomena. Old and New Acid Open Hearth Practice Some of the recent statements in the literature regarding acid open hearth operation are based on old heat data which are not typical of modern American practice. These old heat logs have been responsible for many misconceptions regarding the acid hearth practice and represent heats which do not coincide with modern methods. In recent years, American practice has been altered materially and these changes will be briefly described. Modern American Practice: A typical log of a modern American acid open hearth heat' is shown in Fig. 1 which indicates that the refining time was only two hours, during which the carbon was eliminated rapidly and the bath temperature increased at a fast rate. The manganese and silicon contents of the metal were essentially eliminated and their oxides had become constituent parts of the slag at the "melt-down" period. During the course of the heat, the MnO content of the slag remained practi-

Jan 1, 1954

By Gordon H. Geiger, J. Bruce Wagner

Electrical conductavity and therrnoelectvic nzeasuretnents on synthetic hematite slabs with 0.01 to 0.90 at. pet Ti and with 0.30 at. pet Ca were made. Additions of titanium and of calcium both increased the electronic conductivity with titanium yielding greater n-type behavior and calciurn p-type behavior. Reduction studies of hematite to magnetite in CO-CO2 atmospheres between 600° and 900°C initially exhibited linear kinetics. These linear rates were increased by additions of titanium and decreased by calcium. IN recent years many studies have been reported in the literature on the kinetics of the reduction of hematite and magnetite to iron. In addition, Hansen and Josephl and Schenck and Schultz2 have reported studies on the reduction of hematite to magnetite, the first step in total reduction to iron. In order to evaluate the results of the studies of over-all reduction in terms of the actual mechanism of the reaction and to define further the important factors in the rate- controlling mechanism of the magnetic roasting reaction, the following experiments were undertaken. Specimens of undoped hematite and hematite containing titanium or calcium in solution as doping agents were reduced to magnetite in CO-CO2 mixtures. In addition, electrical-conductivity measurements were correlated with the reduction kinetics using concepts of defect solid-state chemistry. EXPERIMENTAL Fisher certified Fe2O3 powder was used to make specimens for both the electrical and kinetic studies (see Table I for analysis). Doping with titanium and calcium was accomplished by adding TiO2 and CaO powders to the Fe2O3 powder. The powders were mixed in a Waring blender for minimum times of 1/2 hr. Satisfactory blending was achieved based on comparison of analyses of individual specimens af- ter reduction. The specimens were formed in a steel die using opposed punches with a rectangular opening 10.0 by 40.0 mm. The Fe2O3-TiO, platelets were pressed cold at 16,000 psi. They were sintered for approximately 16 hr at 1075°C in air, in accordance with information in the literature3, 4 on the time and temperature needed to obtain solution of the titanium in the hematite. The Fe2O3-CaO mixtures were first cold-pressed at 20,000 psi and sintered for 3 hr at 1225°C to insure solution of CaO. This material was then ground to -325 mesh in a 6-in. ball mill and the resulting powder was used to make platelets in the same manner as above. The sintered platelets were usually between 1/16 and 1/8 in. thick. They were ground on a carborundum wheel and polished on 2/0 paper. Typical dimensions of the kinetic-study specimens were 1.6 by 0.8 by 0.05 cm, and a typical weight was 0.3 g. Conductivity and thermoelectric specimens were approximately the same size, but were subjected to further sintering in order to ensure maximum densification. Finally, all specimens were measured to the nearest 0.0005 in. and weighed on a Mettler H-15 balance to the nearest 0.0001 g and the density calculated. The average density of the specimens used for the reduction studies was 4.87 g per cc, or 7.1 pet total porosity. The standard deviation ranged from 0.14 to 0.063 g per cc within a composition group. In the present study, the apparent surface area as measured with a micrometer was taken as the true surface area. The chemical analyses for calcium and for titanium within a group showed maximum variations of 50.04 pet from the average values used in Figs. 9 and 11. In order to suspend the specimen from the balance for the kinetic studies, a hole, 0.03 in. in

Jan 1, 1965

By J. Chipman, G. G. Hatch

One of the important functions of the iron blast furnace is the desulphur-ization of pig iron before it enters the steelmaking furnaces. However, the increasing concentrations of sulphur in the metallurgical coke, source of approximately 90 pct of the sulphur present in the blast furnace charge, and demands for higher rates of production within recent years have increased the need for greater desulphurization within the iron blast furnace. Furnace operators are beginning to look for desulphurizing agents other than blast furnace slag to accomplish the desired degree of desulphurization. A considerable amount of work has been done on desulphurization outside the furnace with soda ash, calcium carbide and various synthetic slags. Whether the desulphurization of pig iron is accomplished wholly inside the furnace or partly inside and the remainder outside, will be determined by the economics involved. Regardless of which is the case, it is believed that it is necessary to have a better understanding of the physical chemistry of desulphurization by blast furnace slags. To this end, it is the object of the present investigation to attempt what is believed to be the first equilibrium study of the distribution of sulphur between liquid pig iron and a wide range of blast furnace slag compositions. Review of Literature There is a considerable amount of information in the literature concerning the desulphurizing power of iron blast furnace slags, the solubility of various sulphides in the slags, and the effect on desulphurization of temperature, of elements dissolved in the liquid iron, and of viscosity. However, there is nothing to indicate that the equilibrium distribution of sulphur between liquid iron saturated with carbon and iron blast furnace slags has been studied experimentally. Wentrupl has made probably the most detailed study of the desulphurization of pig iron to date. He considered that there are three distinct aspects involved, namely: 1. Desulphurization within the blast furnace (by lime and manganese). 2. Subsequent desulphurization by manganese. 3. The effect of subsidiary reactions on the desulphurization by manganese. The experimental work carried out by Wentrup was devoted mainly to obtaining a better understanding of how desulphurization by manganese was accomplished in the mixer and the ladle. Particular attention was given to the part played by carbon, silicon, and phosphorus associated with manganese in the iron, and the effect of temperature on desulphurization. The experimental results indicated that desulphurization by manganese is purely a process of crystallization of manganese sulphide. The addition of silicon to iron melts containing 3.5 pct carbon and less than 0.5 pct manganese had no noticeable effect on desulphurization, but with 1-2 pct manganese the silicon additions improved the desulphurization. Additions of phosphorus also resulted in improved desulphurizati011 by manganese, but the effect was not as marked as in the case of silicon. It was also found that desulphurization by manganese was further improved by lowering the temperature. In order to explain desulphurization inside the blast furnace, Wentrup considered the system iron, sulphur, calcium, oxygen, manganese. (silicon). The distribution of sulphur between the metal and slag was represented by the following equation: (SS) _ (S)Fe + (S)Ca + (S)Mn .... [S] = [s] [1] The parentheses and the brackets represent the equilibrium concentrations in weight per cent of the slag and metal constituents, respectively. Since FeS D (FeS) _ (FeS) (S)Fe LfeS - [FeS] [S] [2] (CaO) + S e (FeO) + (S)Ca _ (FeO)(S)Ca. (S)Ca _ (CaO) Kl = (CaO)[S] [S] ~K1(FeO) [3] Mn + S D (S)Mn (S)Mn (S)Mn K' = [MnpT "1ST = *lIMnJ !4) Substitution of Eq 2, 3, and 4 into Eq 1 resulted in if = L- + *> (Sol + K^ (S) [51 Eq 5 was used to calcu1;lte -f^j and [S] at 1480°C for slags containing 30-50 pct lime, 0.1-2.5 pct iron oxide, 0-26 pct silica, 2 pct sulphur and iron analyzing 1.5 pct manganese. The value for LFaB at 1480°C was found to be equal to 4.5, based on the experimental work of Bardenheuer and Geller.2 The results of the calculations are shown in Table 1. Although the slags are hypothetical and do not represent the range of compositions found in ordinary blast furnace practice, the calculations indicate that lime is effective in controlling desulphurization only if the iron oxide and silica contents of the slag are kept low. Schenck3 did not claim K1 to be a true equilibrium constant, but an empirical value which varied with the silica content of the slag.

Jan 1, 1950

By R. E. Boni, G. Derge

Application of surface tension measurements has been made to molten silicates in order to determine the effect of sulphur upon the surface tensions of synthetic blast furnace slags. In melts with the same molar ratios of AI2O3 + SiO2 to the basic oxides BaO, CaO, and MgO, the surface tensions increase in the order of oxides listed. Sulphur lowers the surface tensions of the basic BaO, basic CaO, acid BaO, acid CaO, and acid MgO slags in that order; and the concentration of excess sulphur at the slag surface increases in this same order of slags. The rate and amount of desulphurization of iron by these slags is favored by a low excess surface sulphur in the slag. IN a previous paper,1 the authors discussed the applications of surface tension measurements of molten silicates to problems of metallurgical interest. Of major importance is the aid that such studies lend to forming a working concept of slag structure. Since the ability of a slag to desulphurize metal depends strongly upon its composition,2"4 fundamental information about the structural differences between various slags which contain sulphur should aid the development of better desulphurizing media. For that reason, the present investigation concerns the effect of sulphur upon the surface tensions of synthetic blast furnace slags. Experimental Procedure , The maximum bubble-pressure method was used to measure the surface tensions of synthetic blast furnace slags in the temperature range 1300° to 1600°C. The method is based upon the equation which was developed by Schrödinger5 from a consideration of the forces of hydrostatic pressure and surface tension of a liquid which oppose bubble formation when a gas is forced through a tube immersed in the liquid. where y is the surface tension between argon and slag in dynes per centimeter; g is the gravitational constant, centimeters per second2; H is the manometer reading in centimeters; s2 is the density of manometer fluid in grams per cubic centimeter; S1 is the density of the medium in grams per cubic

Jan 1, 1957

By S. L. Payne, J. P. Morris, R. L. Kipp, G. R. Zellars

The activities of iron and nickel in liquid Fe-Ni alloys were determined by measuring the vapor pressures of iron and nickel above the alloys and comparing with the vapor pressures of the pure metals. Nickel was found to deviate negatively from Raoult's law over the entire composition range. Iron behaves ideally down to 0.7 mole fraction but shows negative deviations at lower concentrations. At 1600°C the activity coefficients at infinite dilution are 0.40 for iron and 0.66 for nickel. 1 HE formulation of the conditions of chemical equilibrium between liquid metals and gases or slags is an important application of thermodynamics to pro- cess metallurgy. Usually the metal and slag phases are solutions of several components; and for accurate calculations, it is often necessary to use the activities of the components in place of their concentrations. Data concerning activities, however, are quite meager. The evaluation of the activities of iron and nickel, presented in this paper, is part of a project to determine activities in iron alloys at elevated temperatures.

Jan 1, 1960

By Donald B. Evans, Robert D. Pehlke

The solubility of nitrogen in liquid Fe-A1 alloys has been measured up to the solubility limit for formation of aluminum nitride using the Sieverts method. The activity coefficient of nitrogen decreases slightly with increasing aluminum content in the range of 0 to 4 wt pct Al. Based on a nitride composition, AlN, the standard free energy of formation of aluminum nitride from fhe elements dissolved in liquid iron has been determined to be: ?F" = -59,250 + 25.55 T in the range from 1600º to 1750ºC. The solubility of nitrogen in liquid iron alloys and the interaction of nitrogen with dissolved alloying elements in liquid iron have been the subject of a number of research investigations.' Most of this work, however, has been reported for concentrations well below those necessary for the formation of the alloy nitride phase. Data in the concentration region near the solubility limit of the alloy nitride, particularly for systems exhibiting stable nitrides, are important in evaluating the denitrifying power of various alloying elements. They are also useful in determining the stability of a given nitride if it is to be used as a refractory to contain liquid iron alloys. In view of the importance of aluminum as a deoxidizing agent in commercial steelmaking and the fact that its nitride, AIN, is a highly stable compound and has merited some consideration as an industrial refractory, the following investigation was undertaken. The use of the Sieverts technique provided a measurement of the equilibrium nitrogen solubility in liquid Fe-A1 alloys as a function of nitrogen gas pressure up to 3.85 wt pct A1 in the temperature range of 1600º to 1750°C. The values obtained by the Sieverts method were checked by means of a quenching method in which liquid iron was equilibrated with an A1N crucible under a known partial pressure of nitrogen gas, and the solubility of A1N in liquid iron determined by chemical analysis. EXPERIMENTAL PROCEDURE The theoretical considerations involved in determining the solubility product of a solid alloy nitride phase in liquid iron by measuring the point of departure of the nitrogen gas solubility from Sieverts law have been discussed by Rao and par lee.' The principal problem is to determine the variation of nitrogen solubility in an alloy as a function of the pressure of nitrogen gas over it with sufficient precision to establish the break point in the curve at the solubility limit of the alloy nitride phase. A fairly large number of data points are required to do this. A second problem is the determination of the composition of the precipitated solid nitride phase. This is necessary in order to define completely the thermodynamic relationships. The Sieverts apparatus used to make the nitrogen solubility measurements in this investigation is of essentially the same design as that described by Pehlke and E1liott.l The charge materials were Ferrovac-E high purity iron supplied by Crucible Steel Co. and 99.99+ pct pure aluminum. Recrystal-lized alumina crucibles were used, and were not attacked by the liquid alloys. The hot volume of the system which was measured for each melt ranged from 46 to 50 standard cu cm and was found to decrease linearly with decreasing pressure and with increasing temperature. The temperature coefficient of the hot volume at 1 atm pressure of argon gas was essentially constant for all experiments at a value of -6 X 10-3 cu cm per "C. The melt temperature was measured with a Leeds and Northrup disappearing filament type optical pyrometer sighted vertically downward on the center of the melt surface. The temperature scale was calibrated against the observed melting point of pure iron taken as 1536°C. The emissivity of all melts was assumed to be that of pure iron, taken as 0.43. The charge weights ranged from 110 to 140 g and the range of aluminum contents covered was from 0 to 3.85 wt pct. Aluminum additions were made as 12 to 15 wt pct A1-Fe master alloys previously prepared in the system under purified argon. The compositions of the master alloys were checked by chemical analysis and found to be in agreement with the charge analyses. Vertical cross sections of the master-alloy ingots were used as charge material for the equilibrations in order to minimize the effect of any segregation which might have occurred during solidification of the master alloys. Determinations of the solubility product of

Jan 1, 1964

By M. L. Pearce

A comparison of the isotope-dilution, vacuum-fusion, and chemical methods of analysis for nitrogen in Si-Fe is made with particular emphasis on the effect of sample history. The superiority of the isotope-dilution method from the point of view of 1 HE analytical techniques used to determine nitrogen in Si-Fe have been subjected to close scrutiny in recent years primarily because of the marked influence of the element on the properties of the alloy. These investigations have led to a diversity of opin- both precision and accuracy is demonstrated. The solubility of nitrogen in 3.06 pct Si-Fe is investigated and the effect of silicon content on the activity coefficient of nitrogen is derived. ion regarding the reliability of the vacuum-fusion and chemical methods of nitrogen analysis when applied to si- Fe.'-' A majority of workers appear to favor the vacuum-fusion method over chemical methods particularly in those cases where part of the nitrogen may exist as silicon nitride or the total nitrogen content is very low. Contrary views have been expressed, however,' and it has been demonstrated that for some Si-Fe alloys both methods yield results which are significantly lower than those

Jan 1, 1963

By Donald B. Evans, Robert D. Pehlke

The solubility of nitrogen in liquid Fe-B alloys has been measured up to the solubility limit for the formation of boron nitride. The activity coefficient of nitrogen increases with increasing boron content in the range 0 to 7 wt pct B. From experimen -tal data, values have been calculated for the B-N interaction parameter e3 at temperatures in the range 1550" to 1750°C. A value of 0.038 has been estimated for the boron self-interaction parameter eg at 1550°C. The standard free energy of decomposition of boron nitride into the elements dissolved in liquid iron has been determined to be: ?F° = 45,900 -21.25T in the range from 1550° to 1750°C. The nitride is assumed to be of composition BN. BORON nitride has an unusual combination of properties which make it appear attractive in a wide range of engineering applications. Some of its more important and most recent applications are in the nuclear area, particularly in connection with the liquid-metal cooled reactor concept now receiving considerable emphasis. Boron nitride has a high degree of stability at elevated temperatures. It also has excellent ma-chinability and the ease with which its crystals deform suggests applications as a lubricant. These properties stem from a hexagonal layer-type structure similar to the structure of graphite. One of its primary uses to date has been for seals in liquid-metal pumping systems. It is also used in nuclear reactors as an insulating layer to separate two solid metals which are not themselves compatible under the conditions of temperature and atmosphere in which they are used. Its inertness to liquid metals has also suggested use as a mold-release agent in casting processes. In addition to its excellent machinability and reported inertness to liquid metals such as iron, silicon, aluminum, copper, and zinc, boron nitride has high thermal conductivity and excellent thermal shock resistance. This combination of properties would make it appear ideal as a refractory crucible material for refining of high-purity liquid metals, for example high-quality steels. However, since it is known that concentrations of boron as low as 50 ppm can have a marked effect on the physical properties of certain steels,' in particular on the creep and stress-rupture properties, an investigation was undertaken to define accurately the chemical equilibrium among boron, nitrogen, and liquid iron in the range of steelmaking temperatures. EXPERIMENTAL PROCEDURE Two experimental approaches to this problem were employed: a Sieverts' method and a quenching method. In the first method, the Sieverts' technique was used to measure the equilibrium nitrogen solubility in liquid Fe-B alloys of 0 to 7 pct B as a function of nitrogen gas pressure over the melt. The solubility limit of the boron nitride phase formed was determined by the point of departure of the nitrogen absorption from Sieverts' Law. This technique has been applied to liquid Fe-Ti alloys by Rao and parlee,' to liquid Fe-A1 alloys by Evans and Pehlke,3 and to solid Fe-V alloys by Fountain and Chipman.4 In the second method a melt of liquid iron was held in a crucible of boron nitride under a known partial pressure of nitrogen gas. After thermodynamic equilibrium was attained, the melt was quenched in a stream of helium and then analyzed by wet-chemical methods for boron and nitrogen. The Sieverts' apparatus used in the first method was essentially of the same design as the one described by Pehlke and Elliott.5 The charge materials were vacuum-melted high-purity iron (Ferro-vac E) supplied by the Crucible Steel Co. and -325 mesh boron powder supplied by Cooper Metallurgical Associates of Cleveland, Ohio. The boron contained less than 0.02 wt pct O, according to supplier's analysis. Recrystallized alumina crucibles were used to contain the melt. Examination of solidified melts showed these crucibles to be satisfactory with no evidence of any reaction or physical penetration of the crucible wall by the melt. The melt temperature was measured by a disappearing filament-type optical pyrometer sighted vertically downward on the melt surface through a 1/4-in.-diam sight hole in the crucible lid. The pyrometer was calibrated against the melting point of pure iron in the same apparatus, taking the emissivity of

Jan 1, 1964

By Tasuku Fuwa, John Chipman

Equilibrium data on the reactions of gases with carbon and oxygen dissolved in liquid iron are reviewed and correlated. A source of error in oxygen analysis of graphitic samples is exposed. New experimental data on the oxygen content of high -carbon iron in equilibrium with carbon monoxide indicate that the activity coefficient of oxygen is decreased by additions of carbon. The carbon-oxygen product decreases slightly with increasing carbon content. In recent years a number of investigations have been reported dealing with the equilibria between carbon and oxygen in liquid iron and gases containing carbon oxides. The laboratory study of these reactions dates back to 1931 with the publication of a paper by Vacher and Hamilton' on "The Carbon-Oxygen Equilibrium in Liquid Iron". The principal object of this study was to obtain data on the reaction shown by Eq. [3] below; their data and others by vacherZ permit evaluation of the other equilibrium constants as well. Subsequent studies have been reported by Matoba, Phragmen and Kalling and by Marshall and Chipman.5 The equilibria may be expressed by the following three equations: C + CO,= 2CO;Kl = Pc° [1] 0-+CO = CO,;K2=-P co, "0.PCO c + O = CO; K3 = In the equilibrium constants, ac and a0 are taken as equal to [% C] and [% 0] respectively in the infinitely dilute solution. At finite concentrations an activity coefficient is introduced such that ac =fc [%C], and so forth. It is to be noted that these equations represent only two independent relations, the third being derivable from any two. Richardson and Dennis have determined the conditions of equilibrium in reaction [I] at temperatures of 1560" to 1760°C. Their results have been confirmed by Rist and chipman7 who have shown how the data may be extended to cover the entire range of liquid compositions at temperatures from the eutectic up to 1760°C. An approximate confirmation has been reported by Fuwa and chipman.' These investigations also established the activity coefficient of carbon which was shown to increase rather rapidly with increasing concentration. For the very dilute solutions the value of Kl is expressed in the equation: log^i = - 7280/T+ 6.65 This equation leads to a value of Kl = 430 at 1540° C in excellent agreement with the average value of Marshall and Chipman.5 It is shown as line 1 in Fig. 1 together with the experimental observations. In the case of reaction [2] the direct experimental results can be supplemented by observations on the corresponding reaction with hydrogen, namely reaction [4]:

Jan 1, 1961

By Richard H. Rein, John Chipman

Liquid slags of the system SiO2-Ca0-MgO-A1~03 were equilibrated with liquid Fe-Si-C alloys in graphite or Sic crucibles at 1600°C in pure CO gas at atmospheric pressure, and the silicon content of both phases determined. Ternary slugs of the systern SiO2-CaO-A12O3 were also studied at 1550°C. The silicon content of the metal phase saturated with both graphite and SIC is 22.0pct at 1550°C and In the iron blast furnace, as in nearly all carbon-reduction processes, some silicon is transferred from slag to metal. The importance of this reaction is enhanced by its indirect effect on the transfer of sulfur from metal to slag, and this has stimulated a comprehensive research program on the equilibrium distribution of silicon between slag and metal. Earlier studies'-3 of this same problem provided data for calculation of the thermodynamic activities4 of the components in SiO,-CaO-A1,O3 slags. 22.4 pct at 1600°C. The temperature at which the phases cristobalite, gvaphite, $ SiC, liquid slag, Fe-Si-C alloy, and CO gas at 1 atm pressure can coexist in equilibrium was found to be 1533°C. The results agree well with earlier studies. They are shown graphically as lines of constant silicon cmtent in the metal which also are lines of constant SiO, activity in the slag.

Jan 1, 1963

By J. M. Uys, T. B. King

WalSH, Chipman, King, and rant' have measured the water content (as hydrogen) of actual steel-making slags. An average water content of 290 ppm was found for basic open-hearth tapping slags and 114 ppm for acid open-hearth slags. Upon equilibration of these slags at 1550°C with a 25 pct H20-75 pct Nz atmosphere, the water content increased to about 410 and 300 ppm for the basic and acid slags, respectively. Walsh et al. concluded that an acid slag was thus relatively far removed from equilibrium, and that basic slags showed a closer approach to equilibrium, with the water vapor in the furnace atmosphere. Herasymenko2 contended that these conclusions were unjustified, as the oxygen pressure used in the equilibration experiments, ;bout 5 x X atm, was quite different from that found in the furnace. Consequently, during the experiments the slag composition would have changed due to oxidation of ferrous iron. As an extension of Walsh's work and to attempt to clarify this matter, the solubility of water in a basic open-hearth slag was measured as a function of oxygen pressure. Similar measurements were also made on synthetic silicates in the "Fe0"-Fe203-SiO, system. The experimental technique has been described previously by Walsh et a1.l and Uys and King.3 Samples of the basic open-hearth finishing slag, contained in 10-cc platinum crucibles, were equilibrated at 1550°C with atmospheres of different oxygen pressure but constant water-vapor pressure, Ph~o = 0.192 atm. Calculations, as well as measurements, indicate that this figure approximates the water pressure of the combustion gases in a steam-atomized, oil-fired open hearth. Oxygen pressures in the open hearth can vary from 10"2 atm in the combustion gases to between l0-' and 10" atm in the steel bath. The former figure depends on the combustion practice and the latter on the carbon content and temperature of the bath. The oxygen pressure of the slag should lie somewhere between these extremes and is expected to be closer to that of the steel bath than that of the combustion gases. Oxygen pressures were therefore varied between 10" and 6 x l0 atm. At the lowest pressure the slag "puffed up" when quenched (indicating possible loss of water) so experiments were not conducted at lower oxygen pressures. The results are shown in Fig. 1, which includes the water content of the slag "as sampled". The results show that the water content of the slag increased appreciably on equilibration with water vapor at 0.192 atm pressure and that the water solubility apparently decreases with increased oxygen pressure. The solubilities found are comparable to those of the Li20-Ca0-Si02 system.3 Work with synthetic slags in the "Fe0"-Fe203-SiOz system was performed at 1500" C, with Ph20 = 0.192 atrn and for oxygen pressures varying between 10"2 and 10-lo atm. Samples for chemical analysis were prepared as described by Larson.4 The results are shown in Fig. 2. Some low-silica melts tested at low oxygen pressures "puffed up" when quenched and analyzed less than 100 ppm water; these results are not included in Fig. 2. The melts containing 40 mol pct silica also showed a tendency to "puff up" during the quench, when they were tested at the lowest oxygen pressure. These results indicate that, at constant silica content, the solubility of water decreases somewhat with increased oxygen pressure. The effect is, however, small considering the wide range of oxygen pressures studied. Also, at constant oxygen pressure (above about lom5 atm) the solubility increases

Jan 1, 1963

By David Schroeder, John Chipman

Jan 1, 1964

By Clarence E. Sims

An effort has been made to give both a comprehensive and simplified picture of the origin, modes of formation, and characteristics of nonmetallic inclusions in steel. Exogenous inclusions, those formed by mechanical entrainment or heterogeneous reaction, have their principal source in ladle refractories. Mechanical emulsion is not considered a likely mechanism. Endogenous inclusions, resulting from homogeneous reactions, are formed mainly during cooling and freezing. They are principally oxides and sulfides but include some nitrides and carbides. Deoxidation affects both the quantity and character of such oxide inclusions and significantly affects the size and shape of sulfides. The importance of inclusions is largely in their effect on mechanical properties. It is fitting and proper that we should honor the memory of those technical giants who have left such a rich heritage to our profession. Today, according to annual custom, we pay tribute to such a man. To have been chosen to play a part in this observance prompts in me an inordinate pride while I am humble before the responsibilities of my task. The ranks are growing thin of those who had the good fortune to come under the personal influence of Professor Howe, but the number who continue to benefit from his legacy of technical wisdom con-stantly increases. I am among the latter. One has only to read his works to appreciate his unusual ability to take data and observations from many sources and give them a clear and comprehensive

Jan 1, 1960

By G. Derge, L. D. Kirkbride

In recent years the problem of sulfur elimination in iron and steel-making has been of increasing importance. This interest has been due to the increasing amounts of sulfur coming into the system via raw materials. As a result, many investigations have been directed at obtaining information pertaining to the rate and mechanism of sulfur removal in the blast furnace as well as measuring appropriate thermodynamic quantities. Chang and Goldmanl as well as others2'3 showed that the process of sulfur transfer from molten carbon-saturated iron to blast furnace-type slags could be considered as two opposing first-order chemical reactions. Recently, Ramachandran et al.4 have shown that during desulfurization electrical neutrality is preserved in both phases and iron and silicon are transferred into the slag concurrently with the evolution of carbon monoxide gas. They concluded that the reaction s + c-+ (0)=(S) + CO(g) does not express the stoichiometry of the sulfur transfer process. As in all previous investigations, these authors studied the process of a net transfer of sulfur from metal to slag across a slag-metal interface. However, no experimental data have previously been obtained for the process of sulfurization. It was the purpose of this study to investigate the sulfurization process, i.e., net transfer of sulfur from slag to metal. EXPERIMENTAL PROCEDURE Apparatus—The equipment used in this investiga-tion was typical of that used by others.1-3The furnace was a high-frequency induction unit powered by a 35 kw Hg spark gap converter. Fig. 1 shows a schematic diagram of the apparatus. A two-compartment crucible assembly was employed to melt the slag and metal charges; being similar to that used by Ramachandran,4 in size and design. The atmosphere was that produced by reaction of hot graphite with air. Temperature measurements were made by W-Mo thermocouples which were calibrated against a Bureau of Standards Pt - Pt 10 pct Rh couple. Temperature control was always good to * 5°C and in general was much better than this figure. Raw materials used in the experiments were C. P. reagent grade where possible. The silica used in the preparation of the slags was in the form of highly purified silica flour. Silicon and titanium additions

Jan 1, 1961

By Tasuku Fuwa, John Chipman, David H. Kirkwood

Fe-C-Si alloys in silica crucibles were held at 1600°C in a controlled atmosphere of CO and Co2 and the approach to equilibrium was obsertsed. Results were not of sufficient precision to establish the activity and interaction coefficients. Observations 012 the equilibrium provided an average value for the standard free-energy change which differed by + 1.1 kcal from the earlier accepted value. The C-SL relation at other temperatures is calculated and shown graphically. IN the refining of steel in an acid-lined furnace, it is well known that, unlike in basic refining, a very significant amount of silicon may remain dissolved in the metal even when the carbon content approaches a final endpoint. Further, it is known that the residual silicon increases with increasing temperature. The quantitative relation between silicon and carbon can be calculated for equilibrium conditions from data already available on the Fe-C-O and the Fe-Si-O systems. Such equilibrium calculations could show us approximately the limitations within which the reaction would be expected to operate in practice. In the oxidation of a bath containing both carbon and silicon it is well known that at low temperatures silicon is preferentially oxidized first. It can be shown by calculation that at high temperatures carbon will be oxidized preferentially. It is the purpose of this paper to record direct observations on the Si-C relation by means of experiments carried out in an atmosphere of carbon monoxide for Fe-C-Si alloys contained in silica crucibles. When such a system is brought into equilibrium, at a fixed temperature, the composition of the liquid metal is governed by the following equations: Both K1 and K2 are known with a fair degree of accuracy, and may be calculated from the tabulated In general the percentage of CO2 is extremely small compared to that of CO and in the experiments to be described the partial pressure of the latter was generally only slightly below 1 atm. EXPERIMENTAL METHOD The induction furnace employed was the same as that described by Rist and chipman' and by Fuwa and chipman.2 It was modified slightly in view of the change from alumina to silica crucibles. The small silica crucible was surrounded by a thin susceptor of molybdenum sheet which in turn rested inside a zirconia crucible. Since the zirconia was subject to breakage, it was supported inside an alumina crucible. The charge consisted of 30 to 35 g of electrolytic iron along with the required amounts of refined silicon and graphite to produce a melt of required composition. Purified carbon monoxide and carbon dioxide were passed into the furnace through carefully calibrated flow meters. Two separate and independent series of experiments were carried out. In Series I (D.H.K.) the melt was held in the furnace at 1600°C for periods of time up to 6 hr. Samples were taken at intervals in silica tubes and were analyzed for carbon and silicon. The results of the last one or two samples taken from each experiment and the direction in which equilibrium appeared to be approached are shown in Table I. In Series II (T.F.) the silica crucibles were of less satisfactory strength and the melts were held at 1600° C for periods of only 2 to 4 hr. In heats number 29 to 45 inclusive, the metal was cooled in the furnace and the ingot itself served as a sample for analysis. In heat 46 and all subsequent heats, samples were withdrawn in silica tubes at the termination of the heat, and these samples were analyzed. The results of all of these experiments in which equilibrium appeared to be approached are listed in Table II.

Jan 1, 1965

By H. W. Hockin, D. r. Brandt, R. H. Walsh, P. L. Dietz, P. R. Girardot

New Jersey, Florida, and Canadian ilmenites were reduced with hydrogen or coke under various experimental conditions and the phase changes occurring in the ilmenite upon reduction have been studied by microscopic examination of polished sections and by X-ray diffraction. The products formed were dependent upon the type of ilmenite, temperature, time and reducing agent. Of the reducing agents, hydrogen was the more effective at lower temperatures. 1 HE possible utilization of ilmenite as a source of both iron and titanium has resulted in the development of a number of methods for the separation of the iron and titanium content. Slagging processes as currently used in Canada are typical of such methods. Somewhat less attention has been given industrially to the reduction of the iron content at less than the slagging temperature. Although references maybe found to such work, in general only one type of ilmenite, either natural or synthetic, has been studied by each author. We have attempted to draw some relationship between the results of experimental reduction and the type of deposit from which the ilmenite was derived, as evidenced by phases occurring in the ores and in the reduction products. Ilmenite ores having from 27 to 61 pct titanium dioxide were included in this study and in each case reduction was carried out at such temperatures that only limited coalescence of the particulate iron product occurred within the ilmenite grains. The history of the individual ilmenite samples and the temperature of reduction were found to determine the occurrence of various phases and the mode of distribution of the iron. REVIEW OF EARLIER WORK ON REDUCTION One of the earliest references to the reduction of ilmenite at less than the slagging temperature was made in 1917.' The metallic iron produced was_____ leached out by the action of dilute sulfuric or hydrochloric acid, to leave a product high in titanium dioxide. Subsequent to this, numerous patents2-'? and other references13"21 have appeared concerning reduction of ilmenite by carbon, hydrogen, carbon monoxide, methane, coal gas, water gas, or the like in the absence of fluxing agents. Mineragraphic examinations were not reported, and in the main, the only examinations made were chemical analyses. However, in two cases3,13, titanium suboxides were reported in the products and in one case2' rutile was reported, in addition to metallic iron. Both were identified by X-ray diffraction. While reductions in the absence of fluxing agents were generally followed by either a wet or dry chemical process for removal of the metallic iron, a Canadian source17 reported removal of the metallic iron by magnetic separation. By the addition of fluxing agents during reduction, the metallic iron has been coalesced into "pearls." Each reference to such a process23-28 has shown that the coalesced iron could be removed by magnetic or gravity means after the product was crushed. In the absence of fluxes, the coalescence did not generally occur. The major part of the present study has been limited to reductions without fluxing agents in order to determine the primary reactions of naturally occurring ilmenites. Titaniferous iron ores have also been studied,29-33 17, l9 their reduction having been used as the basis of a commercial process for beneficiation of such ores in Norway29 and more recently considered in the United States34,35. The ease of reduction of titaniferous iron ores relative to that of hematite or magnetite has been referred to,33 with the conclusion that the more

Jan 1, 1961

By Maxwell Gensamer

Jan 1, 1960