Search Documents

By T. Klemetti, W. H. Su, M. A. Van Dyke

Entry stability in coal mines is dependent on geologic conditions and engineering controls. Most engineering controls in ground control are predictable and standardized for typical geologic conditions. However, geologic anomalies may exist that are difficult to detect with traditional core hole drilling. Borescopes offer a cost-efficient way to gather more geologic data between core holes. Additional data obtained from borescope results provide a clearer picture to enhance detection of hazardous conditions due to geologic anomalies. The equipment, methods, and analysis of borescope results provide geomechanical engineers with a clear understanding of strata behavior and the best information to implement roof control plans and supplemental support to enhance miner safety and health. INTRODUCTION Borescope technology has changed very little since its inception. However, the idea to use borescopes to examine roof strata started with the U.S. Bureau of Mines in 1979 with the production of a fiber-optic borescope (FitzSimmons, et al., 1979). The first documented use of a borescope in the coal mining industry began during the 1980s in Australia by researcher John Shepherd. Shepherd’s idea was to use a borescope to collect a series of data points from the roof lithology and compose a geologic cross section. The cross section was then used to identify key features that suggested the beginnings of roof failure. The features Shepherd identified were bedding plane separations in the roof and low angle, extension, and tensile failures. Shepherd also suggested that the borescope findings could be used for geologic mapping for lithological variation, fracture distribution, and determining if supplemental roof support was needed (Shepherd, et al., 1986). In the United States the first publication about borescope usage for coal mine stability assessment was by Su and associates in 1999, who specifically related the combination of using borescope, geophysical, and corehole data to produce geologic hazard maps (Su et al., 1999). This work directly linked the usage of a borescope with the design of supplemental roof support. The use of borescopes in mining was adopted industry wide by the 2000s. Operator case studies were being published using borescopes to aid in supplemental support recommendations and hazard mapping. An Australian study published in 2007 based the optimization of secondary support after each longwall pass on the results of borescope data. The study stated that the borescope was an invaluable tool for understanding roof behavior (Black, et al., 2007). In 2009, a publication by the National Institute for Occupational Safety and Health (NIOSH) took the concept of borescoping one step further. The work centered around creating a roof quality index (RQI) for limestone mines based on borescope data. The RQI attempted to assign a ranking to establish the nature of the roof and its stability (Ellenberger 2009). In theory, this would have been a very useful tool, but the RQI system has not been widely adopted in the industry.

Jan 1, 2019

By N-h. Mao

We applied kriging (geostatistics) to interpret the structure of basement rock in Yucca Flat, NTS from borehole data. The estimation error for 118 data is 81 m comparable with those based on both gravity and borehole data. Using digitized topographic data, we tested the kriging results and found that the model validation process (Thomas option) on data gave a fair representation of the overall uncertainty of the kriged values.

Jan 1, 1985

By John E. Wiegand

"We will attempt to explain the basic workings of a modern seismograph and how the recorded data can be interpreted, not only for determining compliance to the regulations, but also in determining whether or not a seismograph record is accurate and valid. We will discuss some parameters that should be included in all seismographic recordings. We will give examples and use overhead slidesto show examples of both accurate and valid recordings, and tampered and inaccurate seismograph recordings. Much of the information presented will be basic in nature, and will reflect the opinions and personal experiences of the author. We ho'pe the listener will gain valuable information concerning the use and interpretation of seismographic data, as well as find interest and sometimes humor in the examples shown."

Jan 1, 1992

By J. G. Wiese

Reagents are added to the flotation process of Merensky Reef ores to achieve specific functions that enable the separation of valuable minerals from gangue minerals on the basis of the difference in their surface properties. However, due to the complexity of the process, the various interactions that occur as well as the incomplete liberation of the ore and range of minerals present, it is difficult to quantify the behaviour of each of the reagents. More specifically, changes made to achieve a particular outcome may have secondary effects that can override the desired effect. If all the effects and interactions can be accounted for, it is possible to manipulate reagent suites and obtain better overall metallurgical performance. This paper discusses the effect of the addition of copper sulphate at different operating points of the recovery of the sulphide minerals. Batch flotation tests indicated that the recovery of chalcopyrite was not affected when operating conditions were varied, whereas pentlandite recovery was strongly affected by the point of reagent addition, and pyrrhotite recovery was enhanced by copper sulphate addition, irrespective of the point of addition, with the extent being dependent on the ore source. Floatable gangue was activated by copper sulphate in the presence of the dithiophosphate collector. Froth stability was also affected by copper sulphate addition.

Jan 1, 2006

By J. G. Wiese

Reagents are added to the flotation process of Merensky Reef ores to achieve specific functions that enable the separation of valuable minerals from gangue minerals on the basis of the difference in their surface properties. However, due to the complexity of the process, the various interactions that occur as well as the incomplete liberation of the ore and range of minerals present, it is difficult to quantify the behaviour of each of the reagents. More specifically, changes made to achieve a particular outcome may have secondary effects that can override the desired effect. If all the effects and interactions can be accounted for, it is possible to manipulate reagent suites and obtain better overall metallurgical performance. This paper discusses the effect of the addition of copper sulphate at different operating points of the recovery of the sulphide minerals. Batch flotation tests indicated that the recovery of chalcopyrite was not affected when operating conditions were varied, whereas pentlandite recovery was strongly affected by the point of reagent addition, and pyrrhotite recovery was enhanced by copper sulphate addition, irrespective of the point of addition, with the extent being dependent on the ore source. Floatable gangue was activated by copper sulphate in the presence of the dithiophosphate collector. Froth stability was also affected by copper sulphate addition.

Jan 1, 2007

Landscape interpretation, geology and mining history is being successfully used to explore options for sustainable community tourism product development. Recent work by the author in Europe and Australia has indicated the value of adding and producing interpretive information about mine and quarry locations - both active and inactive. This work has allowed for the branding and development of new sustainable community tourism products based on the landscape, folklore, mine and geological heritage.   Communities in rural areas are seeking new opportunities to sustain their local economies. Using a relatively new phenomenon called geotourism as a starting point; they have developed themed products connected to walking/cycling guides, interpretive panels and visitor centres. These themes can be linked to geology, archaeology, botany, local history and to industrial heritage sites such as old mines, to generate local employment. This new geotourism approach has successfully brought a new and greater audience to discover the value of geology and mining history.   Communities have established a unique place for themselves within the tourism marketplace using the geotourism brand. Other communities with an established tourism product are also now using geological and mine heritage via geotourism to rebrand and meet changing global trends. The pooling of resources under the banner of geotourism has led to cost effective marketing, targeting and promotion of products.   Geotourism has emerged strongly in Europe, North America and China in the last decade. The Australian minerals industry now has an opportunity to implement this new branding concept to assist and benefit the communities in which they run their activities. Communities can also take advantage of the potential to develop a sustainable geotourism business around a past or present mineral industry in their vicinity.

Jun 1, 2010

By Robert M. Valentine, Randall L. Lentell

Interpretive geotechnical investigations were performed for the construction of approximately 15,250 m (50,000 ft) of wastewater interceptor tunnels in Austin, Texas. Subsurface materials consist of claystone (or clay shale), siltstone, altered volcanic tuffs, chalk and limestone. Special conditions include multiple crossings of Onion Creek with cover ranging from about 1/2 to 3 m (2 to 10 ft.), and the potential for mixed-face conditions consisting of water-bearing gravels overlying clay shale or siltstone. The methods and results of the geotechnical investigations are discussed and the inferred construction conditions are compared to those encountered during tunneling. A suggested format is presented for interpretive geotechnical reports for underground construction projects.

Jan 1, 1985

By M. H. Tyeb, C. Banerjee, A. K. Majumder

The primary requirement from a hydrocyclone is the classification of the feed solid particles. Particle classification occurs inside a hydrocyclone by virtue of the relative radial distribution of the suspended particles, based on their size and specific gravity. The particle classification behaviour in a hydrocyclone is experimentally studied in this paper. The phenomenological features of the air core at different feed solid concentrations and the distribution of the solid concentrations in the hydrocyclone are also analysed by the theoretical study of flow features in a steady Rankine vortex. Semi-empirical models for predicting the hydrocyclone performance in terms of flow split ratio, and cut size have been developed using the background knowledge of convoluted hydrodynamics. In addition, to validate the classification performance of a smaller diameter hydrocyclone, the potential of the present model is extended for envisaging the same for larger diameter hydrocyclones. A comparison between the model predicted values and the measurement data shows a good match. Keywords: Hydrocyclone, classification, Rankine-vortex, air core, modelling

Jan 1, 2020

By Lev Filippov, Vyacheslav Severov, Inna Filippova

"Reverse cationic flotation is a very efficient method of beneficiation of oxidized iron ores when you need to separate hematite and quartz. This method can be also applied to reduce silica content in the magnetite concentrates obtained by wet low-intensity magnetic separation. However, cationic flotation in this case is less effective due to the presence of Fe-Mg-Al-bearing silicates as amphiboles in magnetite ores. These silicates are concentrated in magnetic products and determine the difficulties of their separation from iron oxides when amines and starches are used as collectors and depressants, respectively. The recalculation of the results of the electron microprobe analysis of three calcic Fe-Mg-Al-bearing amphiboles used to characterize cation distributions in structural units and to obtain structural formulas in accord with stoichiometric limits was conducted. The Mössbauer spectroscopy was used to examine the validity of the empirical estimation of cation distributions in amphiboles. The studied samples are metamorphic pargasite and ferrotschermakite and volcanic magnesiohornblende. The crystallographic analyses of the amphibole samples exhibited their heterogeneous surfaces explaining worse floatability of amphiboles with dodecylamine at pH 10. The electrokinetic measurements showed that the position of the isoelectric point of amphiboles is related to a substitution of Al3+ for Si4+ in tetrahedral sites and to an amount of Mg2+ cations in octahedral sites. Thus, the dodecylamine adsorption onto amphiboles through electrostatic interactions is mainly affected by a distribution of these cations in tetrahedral and octahedral sites of amphiboles. In addition, the effect of starch on the depression of Fe-Mg-Al-bearing amphiboles during flotation can be attributed to the presence of metal ions on the amphibole surface, which are capable of forming strong chemical complexes with starch molecules."

Jan 1, 2014

By J. C. Hower

The Hardgrove grindability index (HGI) is a widely used coal-quality parameter with applications in coal mining, beneficiation, and utilization. An understanding of the petrology of the coal is fundamental to understanding the validity of the HGI in the given application. The HGI varies with coal rank, increasing (greater ease of grinding) with increasing rank through the high-volatile bituminous rank range; and the HGI varies with changes in the maceral and microlithotype composition, decreasing with an increase in liptinite and liptinite-rich microlithotypes. In this review, the .fundamental relationship between HGI and coal petrology, and consequently its relationship to coal utilization, is examined.

Jan 1, 1999

By William H. McLemore

Geologists searching for carbonate rocks suitable for chemical uses traditionally have relied on extensive laboratory testing in order to locate strata or zones that might be suitable for mining. However, when considering the significant time and costs involved in sampling and performing chemical analyses, any exploration technique whereby fewer samples and analyses are needed would be of great value. In other words, if the exploration geologist could "zero-in" on select areas, considerable time and money could be saved. In general, the major-element chemistry of carbonate rocks is determined by the abundance of the minerals present. CaO occurs with CO2 as the mineral calcite, which is the primary mineral comprising allochems, matrix and sparry cement; MgO is found in high-magnesium calcite (many calcite fossil species contain appreciable amounts of MgO in solid solution), dolomite, and chlorite; iron occurs in pyrite and in limonitic stylolites, as well as in chloritic and glauconitic clay minerals; materials containing abundant Si02 are microcrystalline quartz (chest) silt-sized quartz, and clay minerals; and Al203 is found primarily in illitic, kaolinitic, and chloritic clay minerals. The presence or absence of these minerals determines the chemical composition of the carbonate rooks.

Jan 1, 1983

By J Jardine

An improved ground support method for development intersections, wide spans and stope brows was implemented at Kanmantoo mine. The method uses a jumbo to simultaneously drill and install self-drilling anchors (SDAs) to depths from 4.5 m to 7.0 m. Resin is subsequently pumped into each SDA using a specially designed integrated tool carrier basket, with plating occurring within 10 mins due to rapid resin cure. This methodology means that SDAs can be installed rapidly due to reduced process steps and wait times with reduced hazards to personnel. Cablebolts are used extensively in underground mines to reinforce the ground in wide spans, such as at intersections and stope brows. The flexible cablebolt tendon allows for a long, continuous and high-capacity reinforcing element to be inserted into the rock. A common cablebolt installation practice at Australian underground mines that do not utilise a mechanised cable bolter, is for cablebolt holes to be drilled by a jumbo or longhole rig, hand installation and grouting by a service crew, then plate tensioning following a grout curing wait time of typically 12 to 24 hours. This process involves multiple separate labour-intensive work processes and results in reduced availability of priority headings. This paper discusses the development history of vertical SDA use in wide spans at Kanmantoo mine. The installation process is fully described, including aspects such as reliable in-hole coupling of SDAs, resin selection and pumping aspects. A cost benefit assessment, and a case for ground stability are presented to compare cablebolt use to SDAs in development intersections.

Mar 29, 2023

By Yunqing Zhang

Roof failure occurs much more frequently at intersections than entries and crosscuts. Using a commercial finite element package, four-way and three-way intersections reinforced with the tensioned bolts are modeled. The 3-D model considers bolt pre-tension, bolt installation procedure, bedding planes and in-situ horizontal stresses. The modeling results from both four-way and three-way intersections are analyzed with regard to the intersection stability. The mechanisms of tensioned bolting at the intersections are investigated and some tensioned bolting guidelines for intersections are given. Based on this study, a better way to enhance intersection stability is to use longer bolts than entries or crosscuts and increase the bolt density near the intersection corners.

Jan 1, 2003

By B Y. Luan, Y Tian, W Zhou, X Lu, Q X. Cai

The unmanned driving technology in open pit coalmines is an important technology that relies on innovation to drive the development of the open pit coal mining industry in China’s transformation of growth drivers and industrial structure upgrading. It is an important path to solve the shortage of mine truck drivers in the future mining, an important way to improve the working environment of open pit mining personnel, and an important foundation for achieving flexible production capacity in open pit mining to cooperate with the coordinated development of new energy. The communication rules at intersections are key to ensuring the safety and efficiency of unmanned driving in open pit coalmines. This paper proposes a collaborative traffic strategy between unmanned trucks for the single bucket unmanned truck intermittent process system in open pit coalmines. Based on the gap theory, this paper analyses the conflict characteristics and establishes a coordinated traffic strategy for the common intersection and merging conflicts of unmanned truck trucks in open pit coalmines, A multi-agent system simulation platform was built to evaluate the coordinated traffic efficiency under different initial average gap sizes of vehicles, with intersection traffic density, vehicle speed, and gap changes as key indicators. The results show that under the simulation conditions of this article, when the initial average gap of vehicles reaches three (four) times or more of the safe distance, the coordinated traffic performance of intersection conflicts (merging conflicts) is better, and the traffic capacity of intersections is close to the traffic capacity without conflicts.

Sep 1, 2024

By Ray Schmahl

The Glenwood Canyon is a 13 mile long river gorge formed by the Colorado River approximately 2 miles East of Glenwood Springs, Colorado and approximately 150 miles West of Denver Colorado, (See Drawing #1). The canyon walls rise some 800 feet from the river elevation on either side of the river. The South-side river bank is occupied by the Denver and Rio Grande Western Railroad. The Northside is currently occupied by completed sections of Interstate 70 and US Highway 6. The railroad was built in the late 1800's and a hydroelectric power generating station was built in about the center of the canyon in the early 1900's. The Highway 6 platform was completed in the 1930's. The design and alignment for Interstate 70 thru Glenwood Canyon began in the early 1970's. The Highway thru Glenwood Canyon was designated a scenic Highway by the United States Congress, thereby allowing certain deviations from standard Interstate requirements. Environmentalists objections to the construction of Interstate Highways thru Glenwood Canyon resulted in especially careful design to avoid adverse environmental impacts. As a result, in many areas the new Highways will have restored the canyon to its more native configuration than what was the case in the building of the US 6 Highway platform.

Jan 1, 1990

By S. Akhtar

Interstitial compounds of iron, cobalt, and nickel, and their binary and ternary mixtures with silver, gold, palladium, and platinum were prepared and tested as fuel cell catalysts. The first step in the preparation of the interstitial compounds consisted of preparing finely divided metals. This was done either by the Raney method or by reduction of precipitated hydroxides of the metals. The finely divided reduced metals were then treated with carbon-and/or nitrogen-containing gases to prepare their carbides, nitrides, and nitrocarbides. The materials were tested for cathodic activity towards O2 and for anodic activity towards H2, C3H8, NH3, CO, and N2H4 in acid and alkaline electrolytes at 25° to 90° C in half-cell assemblies. Samples of carbided and nitrocarbided INi-lAg-1Au were about one fifth as active as Pt-black in the reduction of O2 in 35 percent KOH solution, whereas the activities of several interstitial preparations exceeded the activity of Pt-black in the reduction of O2 in 12M KOH containing N2H4. Nitrocarbides of x-Fe2C, 3Ni-1Au, and 1Ni-3Au were effective catalysts for oxidizing N2H4 in liquid NH3 containing NH4SCN. Corrosion of the catalysts by electrolytes was severe in many cases.

Jan 1, 1970

By Stanisław Lasocki

We present an algorithm to integrate the uncertainties of mean activity rate and magnitude cumulative distribution function in the interval estimation of the primary seismic hazard parameters: the exceedance probability and the mean return period. The algorithm is applicable for both the parametric and nonparametric modeling of magnitude distribution. When the Gutenberg-Richter relation-based parametric model of magnitude distribution is used, the interval estimation of its parameters is based on the asymptotic normality of the maximum likelihood estimators. When the nonparametric kernel estimation of magnitude distribution is used, we apply the iterated bias-corrected and accelerated method for the interval estimation, based on the smoothed bootstrap and second-order bootstrap samples. Previous studies indicated that the uncertainty of mean activity rate significantly affects the interval estimates of hazard functions only when the activity rate is low and the inference period is not long (Orlecka-Sikora & Lasocki 2017). With increasing mean activity rate, the uncertainty of magnitude distribution dominates over the uncertainty of mean activity rate in the aggregated uncertainty of the hazard functions. The provided algorithm is generic and can be applied to capture the uncertainty of any multiparameter function from the uncertainties of its parameters. Here we present a further development of the algorithm developed by Orlecka-Sikora & Lasocki (2017) by presenting its implementation in the Traffic Light System approach. As an example of use, we present the confidence intervals estimation of hazard parameters for the datasets related to induced seismicity accompanying underground exploitation of copper ore in the Legnica-Głogów Copper District (LGCD) in Poland. The algorithm is under implementation to the EPISODES platform (https://tcs.ah-epos.eu/) - an IT platform that provides access to integrated research infrastructures of the Thematic Core Service of Anthropogenic Hazards (TCS AH) of EPOS (European Plate Observing System). The algorithm is also a component of the pilot developed within the EPOS SP project (No 871121), which aims to strengthen the interaction with the private sector and the added value for society. The pilot demonstrates the potential of the IS-EPOS platform software applications for the technology-related probabilistic assessment of time-dependent seismic hazard. The pilot supports a Traffic Light System approach. The current seismic hazard is compared to threshold values based on the exceedance probability for a given magnitude.

Apr 26, 2022

By D. Tesh

The mining industry worldwide is facing a tremendous shortage of minerals engineers in all fields of specialization. For instance, in Australia the skills shortage in the mining industry has been identified as one of the top risks facing the mining industry. In Namibia most minerals engineers employed are expatriates, with some being Namibians who studied abroad. The minerals engineering programmes at the Polytechnic of Namibia are still in their infancy. These programmes were designed to meet the mining industry skills needs. Being young has its advantages in that lessons can be learnt from older minerals education institutions that went through similar challenges. However, this does not imply just copying and implementing their approaches, since the context differs and, to ensure sustainability of the minerals education programmes, curricula have to be customized to the local context. This paper reviews the interventions made by the Polytechnic of Namibia in order to ensure the sustainability of its minerals education programmes. The methodology consisted of an extensive literature review, a status quo analysis of the mining and process engineering department, identifying the gaps between the current state and desired state, and mapping the goals and strategic actions required to progress to the desired state. The following factors were identified as major threats to the sustainability of minerals education at the Polytechnic of Namibia: the quality of students, low student enrolment rates, low pass rates in science and mathematics, shortage of academic staff, dwindling government funding, and limited involvement of the mining industry. The major outcomes of this research comprise the detailed strategic actions employed by the Polytechnic of Namibia to address the threats to sustainability of its minerals education programmes.

Jan 1, 2014

By Tim O’Neil

What prompted the merger of the two long-established American Mining Congress/National Coal Association (AMC/NCA) groups that combine the coal, hard-rock, industrial- and agricultural-minerals sectors of mining? Both associations have been facing similar stresses for several years - structural changes in their respective industries, the changing personality and role of government and well-financed and organized opposition groups. In 1993, the AMC board of directors undertook efforts at reorganizing the association. One board member, who serves on both boards, suggested it might be time to give serious consideration to merging the organizations. This is an idea that had been discussed more or less informally at least three times during my tenure at NCA. Negotiations toward a merger began after that and were consummated in February of this year.

Jan 1, 1995

By D J. Bradshaw, E M. Wightman, B Newcombe

Flash flotation plays an integral role in many of the gold and sulfide mineral concentrators around the world, and yet despite this widespread use, very little information on this unit process is available in the published literature. For operations to maximise the performance of their flash flotation circuits, understanding how these cells operate, the nature of the particles they target and how to predict whether a flash flotation cell should be used on a specific ore type is of vital importance. This paper provides a summary of the key findings of a large flash flotation research project based in the operating environment of a refractory gold concentrator. The influence of key flotation performance criteria including gas dispersion, residence time and particle segregation within the cell will be discussed and recommendations for process improvements will be made throughout. The nature of the particles within the flash cell will be examined, as will the impact on the type of particles that are passed to downstream processes when the flash flotation cell is taken off-line. The development of a laboratory method to determine whether an ore is suitable to undergo the flash flotation process is also presented for its potential to aid in flow sheet development and optimisation for new ores.CITATION:Newcombe, B, Bradshaw, D J and Wightman, E M, 2012. Into the belly of the flash à Insights into the mechanisms at work within a flash flotation cell, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 163-170 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012