Search Documents

By Mohamed Ourriban, Stéphanie Somot, Éric Proulx, Jean-Sébastien Marois, Marjolaine Drouin, Paul Blatter, Ahmed Bouajila, Claude Gagnon

"The mining industry has to face increasing restrictions concerning the use of fresh water in Québec and throughout the world. Increasing recirculated water usage could lead to a better control of the quality and the quantity of water supplied to the mineral processing units. Furthermore, it could reduce the volume of waste water to be managed and treated before its release to the environment. However, process water may have a negative impact on mineral processing operations, thereby limiting the incentive for sustainable development initiatives. As a first step into selecting and testing remediation strategies, one of which being blending local waters, a mapping of process water quality (inorganic and organic fractions) allowed to locate zones in an industrial case study where fresh water is introduced into the circuit and to detect dissolution and precipitation zones. A complementary hydro-geochemical modeling study on water blends was also performed showing encouraging results towards the objectives of the project.INTRODUCTION The industry has to face increasing restrictions on the use of fresh water in Québec (Quebec Government, 2009) and throughout the world (Brown, 2003; UNESCO, 2006). The cost for the use of fresh water and for water management is highly variable and case-dependent (from 0.2 to up to 7 million dollars/year according to available private estimations, excluding the capital expenditure). It may be, or may become, significant for any plant; thus, risk assessment is of concern here. Using recirculated water could lead to a better control of the quality and the quantity of water supplied to the mineral processing units. Furthermore, it could reduce the volume of waste water to be managed and treated before its release to the environment. However, process water may have some positive and negative impacts on mineral processing operations (Janssen, 2003; Johnson, 2003; Rao and Finch, 1989). Negative impacts could limit the incentive for sustainable development initiatives. Water management strategies at mineral processing sites are supported both by a strategic plan and a water management plan. The strategic plan includes legal aspects, investment costs, potential benefits and various risk levels (Corder and Moran, 2006; Côte et al, 2006; Evans et al., 2006; MacIntosh and Merritt, 2003; McLellan et al., 2008; Merritt and MacIntosh, 2006; Robinson and Keddie, 2006; van Beers et al., 2007a; van Beers et al., 2007b; van Berkel, 2007). In practice, the strategic plan evaluates technical possibilities and costs of various scenarios, such as for example: bringing fresh water to the plant or recirculating waters, or using blends of both. Two important factors to consider in order to enhance the future production efficiency and to minimise risks are: the durability and the stability of the resource, both from quality and quantity points of view."

Jan 1, 2012

In order to overcome some of the deficiencies associated with conventional fine coal cleaning methods, a novel process known as microbubble column flotation (MICROCEL?) was developed at Virginia Tech. This article provides an overview of recent commercialization efforts and in-plant testing of this technology. The results of the in-plant test work indicate that the MICROCEL technology offers several advantages for the upgrading of difficult to clean coals. The test data have also been used to develop guidelines for the design of coal flotation columns and to validate existing scale-up procedures.

Jan 1, 1991

By Naiyang Ma

"High oil concentration is one of the major barriers for recycling of mill scale of steel hot rolling mills. It is of vital importance to find cost-effective technologies of reducing oil concentration in mill scale in order to recycle the mill scale without causing detrimental effects on production and environment. This paper discusses in-process separation of mill scale from oil at steel hot rolling mills. Formation of mill scale and status of oily wastewater at hot rolling mills are reviewed in the first place. A mathematical model is then formulated to relate oil concentration in mill scale to physical properties of mill scale, chemical and physical properties of wastewater and interacting parameters between mill scale particles and wastewater. From this model, three approaches of in-process separation of mill scale from oil are derived: (1) avoiding contacts between mill scale particles and oily wastewater, and (2) maintaining low oil concentration in wastewater, and (3) collecting mill scale in upper streams of wastewater flows. In-process separation of mill scale from oil might have advantages of lower capital cost, lower operating cost and less additional environmental concerns, compared to other strategies of separating mill scale from oil.IntroductionHot rolling is an inevitable step in producing finished steel products. Figure 1 schematically shows a steel hot rolling process. Semi-finished steel products, slabs here, are reheated first, and then the reheated slabs are discharged from the furnaces and transported on hot rolling trains to descaling units for removing scale with pressurized water. After being descaled, the slabs are rolled by roughing mills. After treated with cropping and the second descaling, the slabs are finally rolled into finished products, coils here, by finishing mills."

Jan 1, 2012

By Hatherly P, Dunn P

There are- several in-seam coal research projects currently under investigation by the Cooperative Research Centre for Mining Technology and Equipment (CMTE). The overall aim of the projects is to produce new technologies to enhance safety and the efficiency of in-seam gas drainage drilling. Results from high pressure waterjet rotary drilling trials indicate that by applying high pressure water to a rotary drill bit, the hole can be drilled to follow the planned trajectory very closely. Steerable drill bits for drilling long holes (>1 km) have been produced and trialed. A flexible high speed drilling system provides a capacity for rapid in-seam drilling, particularly suited to cross panel drainage. Geophysical tools are being developed to provide a geological steering capability and a better understanding of potential gas outbursts zones.

Jan 1, 1998

By Iain M. Mason

Linear meridional zones of bad roof conditions have been frequently encountered in producing collieries working the Permian age Lithgow seam in the western coalfield of New South Wales. The prediction of such zones ahead of mining is desirable for reasons of both safety and economics. In March, 1981, we carried out an experimental, three-component in-seam seismic survey at Invincible Colliery to discover whether such zones have any unambiguous seismic effect. The underground survey was the first of its kind to be attempted in an Australian mine. The data quality was excellent with the spectra broadband and clear. Polarisation analysis disclosed two modes: one compressional; the other shear horizontal. The SH model was clearly dispersive and well gound to the plane of the seam. Modal velocities decreased by up to 15% at the fracture-swarm site. There is a strong suggestion on the RLS maps obtained here that the distributed fault zone is acting as a composite scatterer of channel waves. The P-SV and SH wave tomograms obtained show, in a general way, the distribution of stress in the coal panel.

Jan 1, 1982

By M. M. Foss

Geophysical methods are gaining acceptance in the evaluation of coal mine ground control condition. The use of in-seam seismic investigations has contributed significantly to the body of information concerning ground control feature identification and analysis. Seismic methods have been used successfully in locating voids, faults, fracture zones, roof and floor rock interfaces, and more recently in characterizing in-seam stress distribution. Seismic tomography is an effective tool in data interpretation for several of these applications, but as is the case with other engineering application of geophysical techniques, there are limits as to how much substantive information can be interpreted from a given data set. This paper discusses some of the applications of in-seam seismic geophysical tomography, and the limits to which the transformation from raw data to information should be taken.

Jan 1, 1995

Continuing with the effort of providing new and more effective exploration methods to the mining industry, where direct methods (drilling, cross-cutting, etc.) are not applicable, either for logistical or environmental reasons or because they are costly and sometimes ineffective, we present here a new seismic technique based on full wave recording of 3-D channel waves generated within the coal seam across a longwall. In the past two years we reported the application on In-Seam High Resolution Seismic Reflection (ISHRSR) and In-Seam Seismic Tomography (ISST) to map non-coal inclusions that disrupt the coal seam continuity. In the present paper we present a 3-D In-Seam Seismic Tomography (3-DTSST) method using 3-D channel waves recorded by three component high resolution geophones. The method allows to distinguish longitudinal and transversal components of the channel waves, similar to the spheroidal and toroidal modes for the free oscillations of the earth. The recording of these waves allows a more complete analysis of the free modal vibrations of channel waves, permitting a more complete inversion of the structure of the coal seam through which they travel. The full wave analysis provides additional insights of the detailed coal structure for larger, distances than for the ones previously reported using the one dimensional method. The refinement of the inversion software is also a contribution towards the better definition of the coal seam geometry and structures disturbing them such as sandstone channels, sandstone rolls, partings, mine voids, faults, fractures, etc. The method is illustrated with three case studies where subsequent mining revealed the virtues and limitations. The first example deals with the problem of mapping mine works in one side of a longwall panel which geometry is well known, to verify its applicability to map old mine works. The second example deals with a sandstone body that partially scoured the coal seam withing a longwall panel. The third shows an application of the method to map roof conditions in a longwall panel where this problem critically affected production scheduling and costs

Jan 1, 1996

By Leung L, Downey M

This paper presents an overview of a technology package developed by BHP for locating discontinuities in coal seams using an in-seam seismic (ISS) exploration technique. The technology package includes instrumentation, data processing software, field procedures, numerical modelling and interpretation know-how. The technology developed has proved to be highly successful; features such as faults and dykes, not detected by other methods, have been delineated. Using equipment specifically designed for underground use, surveys are carried out quickly and at low cost. More than 30 ISS surveys have been conducted by BHP in Australia. Substantial savings in production revenue have been realised in situations where ISS has identified mining conditions which would have impeded longwall operations. Case studies of several ISS surveys are described in the Paper.

Jan 1, 1987

By L. J. Olivier

The possible closure and subsequent flooding of South Deep Gold Mine?s (SD) neighbouring Randfontein Estates Limited No. 4 Shaft (REL 4) necessitated the construction of five concrete plugs in the connecting tunnels to prevent the ingress of groundwater into REL4 from flooding SD. This paper describes the proposed controlled flooding of REL 4, the planned in-service monitoring of the five plugs and the water barrier between REL 4 and South Deep Mine, and the long-term maintenance of the plugs and rock mass in the immediate vicinity of the plugs.

Jan 1, 2006

By T. Mudder, R. Cellan, R. Waterland, J. Whitlock, B. N. Nelson

The effectiveness of anaerobic in-situ biological treatment for the immobilization of selenium, molybdenum, and uranium in an alluvial aquifer was examined using long-term column tests. A series of organic substrate and nutrient combinations were tested to determine removal effectiveness, optimum supplement concentrations and ratios. Final column testing was conducted to determine the chemical stability of the treatment by-products/treatment compounds by dosing the columns continuously with elevated redox untreated alluvial groundwater.

Jan 1, 2002

By D. R. Reeves

This paper describes the geophysical Jogging of coal that is being carried out for the National Coal Board in the United Kingdom. An explanation of the technique is given and results are presented showing estimations of seam thickness to within ±0.5 in. and ash content to accuracies of ±2.5 per cent. The basic method of interpretation is outlined and some conclusions regarding the conditions of roof and floor material which may be deduced from the logs are explained. An indication of future developments in this field, including the identification of coal type and moisture content, is given.

Jan 1, 1971

By Nobuhiro Ishikawa

The in-situ observation of the effect of impurities on the reduction process of iron oxides by C in TEM was carried out. A few wt% of CaO or AbO, was used as impurities in FeO was prepared. Some precipitates grew into the C layer expect for using 3.0wtCa. The reaction between FeO and carbon was much different from using pure FeO at about 800-1 lOOK. The rate of reaction became much slower including Ca and almost no reaction was happened with the concentration of CaO up to 3.0wt%. On the contrary, AbO, had ahuost no effect on the reaction. The results indicated that Ca suppressed the reaction and the effect of Al was much less. The precipitates which grew into C layer accompanied almost no Ca and AI. Only Fe was detected in the precipitates.

Jan 1, 2008

By Ripu Daman Lama

The size of coal pillars in mines until recently has been determined by experience without being based upon scientific investigations. As a consequence, the size of pillars had invariably been larger than could be accounted for because of the number of unknown factors involved which influence the strength, dictating the use of large safety factors. With the mining going deeper, the size of the pillars greatly increases and sometimes a considerable portion of the mineral property are blocked in the mine pillars required to support the superincumbent strata. With the advances in the field of Rock Mechanics, attention of mine planning engineers has been focused upon the design of mine pillars for safe and efficient working as well as decrease losses of coal. The problem involves the study of three factors: (1) Presence of stresses in the area and their distribution on pillars in the course of extraction. (2) The influence of external factors on the strength of coal. (3) The inherent mechanical properties of coal. These aspects have been studied by a large number of investigators, the first by in-situ stress measurements and photoelastic studies and the second and third aspect by studies conducted in the laboratory on small size specimens (Bunting, 1911; Evens & Pomeroy, 1961; Gaddy, 1956; Greenland et al, 1941; Steart 1954). The size of the specimens tested in the laboratory has been limited to a few inches and the results obtained have been extrapolated by large factors, sometimes several hundred times the largest specimen tested. In these tests much consideration has not been given to

Jan 1, 1971

The principles and utility of in-situ coal gasification are discussed, and a first field test conducted by the Alberta Research Council in 1976 near Forestburg, Alberta, is described. The test was carried out in a 12-ft subbituminous coal seam under 60 feet of cover. Within this seam, a 30 by 60-foot block , containing approximately 650 tons of coal, was delineated by four injection/production holes which were oriented to take advantage of the natural fracture system in the coal. Linkage between holes was established by reverse combustion and gasification was accomplished by injecting air into the ignited coal. No steam was injected but operating pressures were adjusted to utilize formation waters for partial carbon -steam gasification. The coal gasification runs lasted six weeks and gasified an estimated 900 tons of coal ,' during sustained periods of gasification, a fuel gas with heating values of between 110 and 150 Btu/scf was obtained. Plans are now being developed for excavating the test site and inspecting the subsurface cavities created by gasification.

Jan 1, 1977

By Kot F. Unrug

Strength of coal is one of the governing factors in size determination of mine pillars, and therefore affects the percentage of extraction and thus, utilization of reserves. Coal strength is also important from the subsidence control standpoint, where mine pillars with appropriate safety factors should be designed for long term stability. Determination of coal seam strength has been addressed through the extrapolation of the coal strength obtained from a small number of samples on the whole section of the seam. This procedure often gives unreliable results. Presented in this paper is a method of in-situ strength testing of coal, allowing for a realistic determination of seam strength. Results of a field case study dealing with the coal seam, where samples for the laboratory strength tests could not be obtained due to the dense cleat, are presented. However, in these conditions, the in-situ testing was successful. A comparison of both conventional and the in-situ penetrometer method was carried out. It was found that the penetrometer data not only improve the accuracy of strength determination of the entire seam, but also prove to be much more cost effective than the conventional method on a per test basis.

Jan 1, 1995

By Sidney A. Suhler

The persistent requirement for methods and equipment capable of detecting hazardous anomalies in advance of underground mining has led to the development by the U.S. Bureau of Mines of a directional radar probe. The probe operates from boreholes drilled from the surface into the underground region to be mined. The engineering model radar was completed in early 1982 and field demonstration tests were performed in May of that year at a selected coal mine. Preliminary in-situ electromagnetic tests were performed at several candidate coal mines to evaluate the radio-frequency characteristics of the coal. A coal mine in New Mexico was selected on the basis of low EM propagation losses in the coal and the presence of an extensive coal seam displacing fault as a radar target. The borehole radar was operated in two vertical boreholes which intersected the coal seam at approximately 25 and 40 feet from the fault interface. Radar reflections from the coal/ rock interface were detected in both tests. Underground tests in a horizontal borehole in the coal were less successful because of interfering reflections. Additional borehole-to-borehole tests were performed with a separate ground penetrating electromagnetic system to obtain radar range calibration data. The coal was found to be bounded by very lossy roof and floor sandstone and shale while propagation through the coal seam was obtained at distances up to 175 feet between test boreholes. Coal seam continuity was indicated by the hole-to-hole experiments through a section of the seam previously thought to be completely cut off by the fault.

Jan 1, 1983

By C. A. Young, J. D. Miller

Adsorption isotherms previously determined by in-situ Fourier transform infrared/internal reflection spectroscopy (FT-IR/IRS) for oleate adsorption at calcite and fluorite surfaces near pH 9 and at various temperatures are compared. Results indicate that, at both mineral surfaces, chemisorption occurs at equilibrium concentrations below approximately l x l0-5 M oleate while calcium dioleate surface precipitation occurs at higher equilibrium oleate concentrations. The extent of chemisorption at the calcite surface is 3 to 5 times less than that at the fluorite surface while the extent of calcium dioleate surface precipitation on calcite is nearly a magnitude larger than that on fluorite. However, for both minerals, surface precipitation decreases with increasing chemisorption. Contact angle measurements and flotation recoveries show the hydrophobicity of fluorite to be greater than that of calcite at each of the temperatures and oleate concentrations studied. Significant differences are noted only in the chemisorption region. Unlike calcite, the hydrophobicity of fluorite was sensitive to the presence of oxygen in the system. Multichannel Laser Raman Spectroscopy (MLRS) showed this behavior was caused by the double-bond reactivity of adjacent chemisorbed oleate molecules and subsequent formation of an epoxide/polyether complex at the fluorite surface. Such a reaction product could not be detected at the calcite surface. These differences in adsorption density, hydrophobicity, and polymerization behavior are discussed in terms of the intrinsic surface properties of the minerals.

Jan 1, 1999

The properties of interfacial water at hydrophilic surfaces are of great importance in many technological areas including flotation, solid-liquid separation, dispersion and emulsions, flocculation, adsorption, corrosion, and soil contamination. This paper examines the use of FTIR/internal reflection spectroscopy (FTIR/IRS) to study the spectral characteristics of interfacial water at silica surfaces. FTIR spectra were characterized by consideration of the OH stretching region (3000-3800 cm-1) associated with the vibrational spectra of interfacial water. The broad peak in this region was deconvoluted in order to isolate overlapping spectral features that describe the nature of hydrogen bonding in interfacial water. Three distinct bands were found; -3600 cm-1 (free OH), -3400 cm-1 (incomplete tetrahedral coordination), and -3240 cm-1 (complete tetrahedral coordination) and the variation of their intensities with pH was found to be significant. This spectral information helps to explain orientation and bond ordering of interfacial water molecules at hydrophilic surfaces.

Jan 1, 1998

By M. Maldonado, P. Olivares

"A submersible sensor for real-time gas holdup measurement in the collection zone of industrial flotation machines is introduced. The working principle is based on the generation and measurement of a pulp flow using a gas-exclusion cell immersed in the aerated slurry. The gas exclusion cell consists of a variable-area open vertical tube designed to be filled only with pulp by preventing gas bubbles entrance. The higher density of the fluid column within the cell generates a downward flow of pulp; the rate of this flow is proportional to the gas holdup outside the cell. The gas holdup measurement is achieved by tracking the velocity of the pulp flow leaving the gas-exclusion cell, using a magnetic flowmeter. Construction details of a prototype and its testing in two- and three-phases are discussed.INTRODUCTIONFlotation process optimization consists of finding and maintaining operating conditions that maximize flotation performance measured in terms of recovery and grade. The selective separation of mineral particles proceeds in two interactive zones where different and simultaneous phenomena take place: in the collection zone, the valuable particles are separated by collection on the surface of bubbles, while in the froth zone, the bubble-particle aggregates are gathered, drained to remove entrained particles, and taken into the concentrate stream. The cell overall performance, which can be determined from proper stream sampling, is a function of the recoveries in the individual zones. These zone recoveries cannot be independently measured nor calculated from operating variables. Progress in the assessment of these recoveries has been slow because on-line and reliable sensors to measure properties of the drastically different dispersions existing in both zones are not available.In the case of the collection zone, it has been demonstrated that the recovery of hydrophobic particles on the surface of bubbles, considered as a process with first-order kinetics, correlates with the bubble surface area flux (Finch et al., 2000; Hernandez, et al., 2003; Lopez-Saucedo et al., 2012). Bubble surface area flux (bubble area generated per unit time and cell cross-sectional area), is a variable affected by gas flow rate, bubble size distribution, and frother type and concentration. Gas holdup (volumetric fraction of gas dispersed in the slurry) is also affected by the same variables, and as such, carries information on the interacting variables that define the performance of the process. Therefore, a correlation between gas holdup and bubble surface area flux was expected and demonstrated (Finch et al, 2000), and since gas holdup is easier to measure as no bubble size is required, it has the potential to be the basis of a cell control and optimization strategy if a continuous sensor is available."

Jan 1, 2016

By P. J. Nicholson

The methods of reinforcement to be discussed in this paper are all insitu methods, ones that can be used on the soil structure as it exists in the ground, and do not rely on excavation and replacement of the soil. Current practice in the United States, as well as new ideas and methods, will be discussed as they relate to slope stability, retaining walls, and to other uses such as control of mine or cavity related subsidence and to liquefaction control under existing structures. The method is based on the concept of "nailing" or reinforcing the soil in place, and thereby causing a mass of soil to act as a coherent unit. When performed properly, a true gravity structure can be constructed, one that will remain intact under both horizontal and vertical loadings and that will also resist vibrational and seismic loadings.

Jan 1, 2010