Search Documents

By John W. Harshbarger

The Upper Santa Cruz Groundwater Basin lies in the drainage area of the Santa Cruz River in Arizona, and extends upstream from the community of Rillito to the international boundary, see Figure 1. The principal water use area lies between and includes the cities of Tucson and Nogales. A subsurface geologic barrier near Rillito provides a reasonable dividing line between the groundwaters of the Upper and Lower Santa Cruz Basins. The Upper Basin contains the Tucson and Sahuarita-Continental critical ground- water areas. The Tucson Water Use Area encompasses the Tucson metropolitan area and extends from the northern boundary of the Basin south to the boundary between the Tucson and Sahuarita- Continental critical groundwater areas near San Xavier. The San Xavier Use Area is the San Xavier Indian Reservation. The north and south boundaries of the Continental Use Area coincide with the limits of the Sahuarita-Continental critical groundwater area. The first study of groundwater in this valley was initiated by Dr. G. E. P. Smith in 1905 and the results were published in 1910, followed by a series of bulletins of the Arizona Agricultural Experiment Station, University of Arizona, covering the general field of groundwater development and utilization. Beginning in 1939, the Ground Water Branch of the United States Geologic Survey, in cooperation with the Arizona State Land Department and the Arizona Water Commission (AWC), have published a series of bulletins concerning groundwater occurrence and utilization in various areas of the state. In 1975 and 1977, the AWC published the "Arizona State Water Plan" (1), comprising a detailed inventory of water availability and use in the State of Arizona, and a study of alternative futures.

Jan 1, 1979

By D. L. Whiting

Dump leaching and ,in-situ solution mining have received considerable attention during the past few years due to their apparent economic viability and minimal environmental impact. Solution mining actually dates back to the 17th century when leaching of copper ore was first reported. However-, modern day leaching didn't begin on a wide scale until the mid-1900's. In-situ mining for copper, nickel, salts, and oil shale is currently looking more attractive as the technology advances. Presently, about 15 percent of the copper production in the United States is from leaching operations at approximately 14 active sites, the largest of which are the waste dumps near the Bingham Copper Mine, Utah. To establish a common background, the discussion is centered around state-of-the-art conditions. For dump leaching, complications inherent to the physical conditions and chemical reactions such as channeling, porosity and permeability, sorption, air flow, rock alteration and pH control are discussed. Emphasis is made on those conditions which render solution recovery rates and solution mineral concentrations unpredictable. By illustrating typical and actual field conditions, the generally accepted flow theories for both dump leaching and in-situ solution mining, including rubblization, are presented. For in-situ mining, hydrogeologic techniques such as geophysical well logging, aquifer testing and digital computer modeling are also discussed. The importance of artificial fracturing and well stimulating to solution injection and recovery is made with regard to project development. Finally, the subject of water pollution control techniques and the potential impact of the

Jan 1, 1977

By Douglas W. Barr

Water is a necessary part of our environment. It is a biological necessity, but more than that, it is a necessary part of our life style. Those of us who live in the north woods expect water to be part of the scene. There are few natives of this region who would be content to eliminate the streams, the lakes, the marshes, or our forests. Throughout the world, water has been so much a part of man's environment and man's adaptation to life has been so closely tied to water that our way of life and ways of accomplishing our work include water as an essential tool. The production of taconite is an example of our dependence on water. Other methods could have been developed to process taconite ore but the process methods chosen utilize water. Water is used for grinding and separation and for trans- porting the ore from one part of the process to another and for dust control. A typical large plant producing 10 million tons of taconite pellets per year will have on the order of 130,000 gallons per minute (8.202 m 3/51 of water in circulation in the plant. About 120,000 gal. per min. (7.571 m 31s) will pass to tailing thickeners where 110,000 gal. per min. (6.940 m 31s) is separated from tailing and returned to the process. About 15,000 gal. per min. (.9464 m 31s) goes with thickened tailing to tailing basin. My point is that there are great volumes of water in motion in a taconite plant,

Jan 1, 1980

By S. Castro

Hydrolysis of metallic ions depends on pH and the products of hydrolysis either activate flotation or can lead to inadvertent activation of gangue particles, but can also depress flotation of valuable components. One of the most recently studied topics is the use of seawater in flotation. Seawater is a concentrated NaCl solution (about 0.6 mol/L) that also contains considerable amount of Mg2+ and Ca2+ ions. The hydrolysis products of Mg2+ strongly depress flotation of molybdenite over the pH ranges over which they form in the process water. This effect can be eliminated by removal of hydrolysing ions from the process water or by carrying out the flotation at the pH over which such a hydrolysis can be avoided. The former can be exemplified by prior precipitation of the harmful hydrolysing ions as, for example, in the University of Concepcion Patent. The latter can be exemplified by the use of metabisulfite to depress pyrite in the flotation of Cu-Mo sulfide ores in seawater, the process that is carried out at much lower pH, which avoids formation of Mg2+ hydrolysis products.

Jan 1, 2017

By P. R. Taylor

A reaction is evaluated by which heated and pressurized water is used to precipitate metal oxides from loaded Kelex 100 complexes. Pure copper oxide (CuO) and pure nickel (Nio) in powder form, and ranging in average size from 12 to 25 micrometers, were found to precipitate from copper and nickel loaded Kelex 100/kerosene complexes, by water heated and pressurized to between 374 and 400 °c and 2170 psig (148 atm) and 3500 psig (238 atm). The precipitation is suggested to result from hydrolysis of the metal, following exchange for the hydrogen in the phenolic hydroxyl of the Kelex 100 structure, enhanced by the conditions provided by heated and pressurized water. The reaction is believed to have the characteristics of homogeneous nucleation and heterogeneous growth. The effects of temperature, pressure, initial metal concentration and seed addition on the kinetics of the process were studied. In addition, characterization studies were performed on the reaction products. A detailed discussion of the experimental results is presented.

Jan 1, 1992

By Konstantina Chalastara

Mixed phase titanium dioxide (TiO2) nanoparticles synthesized through hydrolysis of TiCl4 solution at different conditions, namely concentration, pH, and residence time are characterized and evaluated as photocatalysts. The process is operated in a continuous stirred-tank reactor, CSTR giving blends of anatase, brookite, and rutile nanoparticles that were further evaluated to find the optimum mixture for a photocatalytic sorption material. The titania nanoparticles are first characterized in terms of photocatalytic activity under UV light illumination using an organic model compound (methyl orange) and after that are tested for removal of toxic selenate and selenite species from simulated effluent waters.

By O. Hungr, V. Gischig, G. Preisig

Deep-seated landslides are characterized by slow time-dependent movements induced by constant gravitational creep, and periods of acceleration associated with stress changes within the rock and the preexisting fracture network. Natural stress changes are typically caused by seasonal variations in surface temperatures and groundwater pressures, but also by rare and more violent events such as earthquakes. These processes are responsible for cyclic loading and unloading that leads to rock mass damage, fatigue and progressive failure with time, and may explain sudden, unexpected rock slope acceleration phases. In this work, we present a set of distinct-element models to investigate and compare the role of hydromechanical fatigue and seismic fatigue in the history of a deep-seated landslide. Hydromechanical fatigue arises from the fluctuation of pore pressure in fractures accompanying periods of significant groundwater recharge. In alpine areas, there are usually one or two cycles per year associated with snow melt and intense rainfall periods. In the presence of a deep confined aquifer within the rock slope, the amplitude of pressure fluctuations may reach values of 0.25-0.5 MPa. Hydromechanical models considering such pressure changes are able to reproduce observed slope accelerations-decelerations phases. Substantial accelerations may occur even in the absence of a cycle of exceptional amplitude, depending on the current state of fatigue. At a given time, one or more fractures may be critically-stressed, and a small change in applied stress is enough to cause local failure and induce a crisis of enhanced slope acceleration. This is augmented if the rock slope contains planes of weakness associated with its tectonic history, glacial debuttressing, etc. The corresponding behaviour is analogous to laboratory experiments on rock and metal fatigue. Similar fatigue effects have also been proposed for repeated earthquake events in seismically active regions. Unlike hydromechanical stress changes that occur in a more localized portion of the rock slope, those induced by passing seismic waves involve the entire rock mass. Moreover, the frequency and amplitude of stress perturbations due to earthquakes are different than those induced by pore pressure variations, although both likely contribute in combination to the degradation and progressive failure of large deep-seated landslides when both are present. The results presented illustrate that: (1) assessment of slope stability near critical infrastructure (e.g., hydroelectric reservoirs) should not only consider static stability, but also failure mechanisms related to fatigue that evolve over time and may result in an apparently stable slope progressing towards a critical state due to relatively small but repetitive stress changes; and that (2) characterization of fatigue processes affecting a deep-seated landslide requires multiparametric continuous monitoring at different observation points.

Jan 1, 2015

By Ronald Molnar

"High demand for metals is driving the exploitation of lower grade and more complex orebodies. These projects are often the initiatives of junior mining companies with limited financial resources. In addition, existing operations seek to enhance revenue from their existing metal recovery operations, through the production of value-added by-product metals and chemicals. Typically, hydrometallurgical circuits, often with novel chemistry, are required to exploit these new ores, to produce the multiplicity of products that will make a marginal project economical, or to increase the product range of an existing operation. Often, the mineral processing engineer is given the task of coordinating the development of a back-end hydrometallurgical flowsheet for their mineral processing project. This paper discusses the objectives that companies have when they commission the operation of a hydrometallurgical pilot plant. The paper goes on to enumerate some of the principal differences between mineral processing and hydrometallurgical pilot plants and the effect these have on the design, operability and potential pilot plant outcomes. Important factors include working with chemically reactive solutions and pulps, elevated temperatures operation, changing rheological properties of slurries, the complexity of integrated circuit flowsheets with long hold-up times and multiple recycle streams, and the need in some cases for extreme attention to purity and cleanliness. Examples will be drawn from the extensive experience base of SGS Minerals Services at the Lakefield site, in piloting both mineral processing and hydrometallurgical process flowsheets.INTRODUCTIONWe are currently experiencing a period of strong growth in the demand for metals. This in turn is turning the spotlight on a great many smaller mining companies and mining promotion ventures trying to tap into the rising metal demand. Some of these companies want to develop their properties and recover metals while others want to develop to the point that a major company will take an interest, or in some cases buy them out completely.With the heightened interest in metals, many orebodies that have been known about for years are being reconsidered for exploitation. Often, the reason they have not been developed to date is because of difficult metallurgy and marginal grades leading to marginal economic viability. In both cases the key that unlocks the resources is often the application of a novel metallurgical flowsheet, often a hydrometallurgical flowsheet."

Jan 1, 2006

By Richard B. Stein

This paper will present an overview of several hydrometallurgical processes which can be used for sea-nodule metal recovery and some simplified economics. Before going any further, here are some of the basic figures from which the economics were developed. The first is to establish a representative composition for a typical nodule feed (Slide 1). This set of chemical analysis figures can be taken as typical for a deep Pacific nodule feed and shows manganese at 30%, copper at 1.1%, cobalt at 0.2%, nickel at 13% and iron at 10% for the metals of economic interest1.

Jan 1, 1982

By Houlihan RN, Landau J

A reciprocating plate column is described in which two sets of perforated plates are mounted alternately on two shafts and are reciprocated with a phase difference of 1800 between them. It is shown that such a column is mechanically superior to the previously proposed types: under practical operating conditions the pressure fluctuations at the base of the column are only a small fraction of the static head. Furthermore, mass transfer experiments with the system tributyl phosphate in kerosene- acid aqueous solutions of uranyl nitrate show that both high specific throughputs and reason- ably good efficiencies can be attained in this type of column. A comparison with the more conventional extraction equipment (mixer -settlers, pulsed columns) on the basis of residence time per equilibrium stage indicates the potential of reciprocating plate columns in hydrometallurg- ical application, especially in which the requirements of separation efficiency are modest while the scale of operation is large.

Jan 1, 1975

By John L. Shafer

A process for the conversion of stibnite (Sb2Sj) concentrates, crude antimony oxide, or metal to a pure cubic antimonous oxide (senarmontite) has been developed on a laboratory scale. The conversion of stibnite to senarmontite has been piloted. The high purity of the final product is the result of forming antimony trichloride as a low temperature distillable intermediate. To obtain the antimony trichloride the stibnite, or crude oxide is slurried in molten antimony trichloride and reacted with gaseous hydrogen chloride. Antimony metal is oxidized to the trichloride with chlorine. The hydrogen sulfide produced from the hydro- chlorination of stibnite can be upgraded to a strength of 95% or greater for further treatment. The crude antimony trichloride is separated from the gangue by a preliminary evaporation and then is fractionally distilled and the trichloride distillate has less than 50ppm of arsenic and lead combined (the most troublesome impurities in antimony processing). The purified antimony trichloride is then hydrolyzed with sodium or ammonium hydroxide to produce the cubic form of antimonous oxide (senarmontite) to the exclusion of the rhombic form (valentinite) which is photosensitive. The advantage of this process is the ability to treat a wide range of antimony ores, concentrates, and metal to yield a high purity oxide in a controllable range of particle sizes.

Jan 1, 1975

By J. W. Smith, J. G. Eacott, D. H. Napier

"Three hydrometallurgicat processes (Noranda chloride leach, B. C. Research biological leach and Sherritt-Cominco activated oxygen leach) and the Noranda pyrometallurgical process have served as the basis for design projects in the final year of the chemical engineering program at the University of Toronto. Each member of a team of five or six students devotes about 200 hours to the project and the final report is expected to include an economic analysis.None of the processes has been developed to full- scale plant, nor, in the case of the B.C. Research and Noranda processes, were pilot plant data available. Nevertheless, the designs developed provide a useful basis for a preliminary estimate of capital and operating costs and for a preliminary assessment of project feasibility.This paper discusses the approach used in the design projects with respect to engineering and economic aspects, and outlines the educational features and benefits of such a program as well as some of the problem areas that arise.IntroductionAs part of the undergraduate degree course in chemical engineering at the University of Toronto, students devote some 200 hours to a design project in their final year. Hydrometallurgical processes, not yet proven at the commercial scale, have been selected for study. The students are required to develop laboratory and / or pilot scale results into a conceptual plant design, using sound engineering principles. Capital and operating costs are then determined and a preliminary feasibility study and economic analysis are carried out."

Jan 1, 1986

By G. Gao

Flyash from municipal solid waste (MSW) incinerators is frequently classified as a characteristic hazardous waste due to its lead and cadmium content. Extensive investigation has therefore been carried out to detoxity the flyash by leaching and to recover lead, cadmium and zinc. Detoxification can be accomplished by leaching in HCI/NaCI solutions. Optimization of leaching conditions for effective detoxification and subsequent metal recovery can be achieved by controlling the acidity of the lixiviant and flyash to lixivaint ratio. Lead and cadmium In the leaching solution is recovered by cementation with zinc dust. Leaching and cementation experiments have shown that zinc concentrations suitable for electrowinning, > 15 g/liter, can be achieved. Experiments have also been performed to determine the effects of pH, particle size of the zinc dust used, quantity of zinc added and dissolved impurities on the cementation kinetics. After recovery of lead and cadmium, electrowinning or electrowinning coupled with solvent extraction can be used to recover zinc. A process flowsheet is presented.

Jan 1, 1991

By L. Li, K. Jiang

China is the world largest producer and consumer of zinc. Beijing General Research Institute of Mining and Metallurgy (BGRIMM) is one of major research and engineering institutes for nonferrous metallurgy in China. This paper (presentation) introduces the development of China’s zinc smelting industry, key production processes and main producers. The process research and development are reviewed as well as BGRIMM’s R&D activities in the last decade. China's refined zinc production was 4,829kt in 2012, accounting for 38.6% of world production. Primary production was 4,722kt. There are around 150 refined zinc producers in China. The traditional fluid bed roasting - leaching jarosite is still a dominant process for primary production and its production accounts for about 60% of country's total production. However, the direct leaching process is gaining market share. Seven direct leaching plants with 330kt/a capacity, including autoclave leaching and the Outotec direct leaching, have been put into production by June 2013. Five autoclave leaching projects with 590kt/a capacity are in the pipe line and are expected to be commissioned in 2014 and 2015. To cut the production cost and improve smelter economics, process research to optimize the production flow sheet, to improve the iron removal and to enhance the recovery of co-existed rare metals were carried out. The development trends of China’s zinc smelting industry from the view of cutting production cost, improving energy efficiency, increasing comprehensive utilization are discussed accordingly.

Jan 1, 2014

The challenges of nature for the recovery of metals for a sustainable future continue to present in diverse ways. Base metal deposits are becoming lower grade and more complex. Rare earth metal demand is soaring and must certainly be met from new sources outside of China. Precious metals have soared in value due to increased industrial usage and the importance of these metals as financial instruments. Many of the future sources of precious metals are complex and difficult to process. The field of hydrometallurgy plays an important role in providing technology for extraction of these metals for a sustainable future. Selected examples from the base, rare and precious metals fields will be used to illustrate how current developments are providing metals for our future. The recovery of rare earths by beneficiation, leaching, purification, precipitation will be described from a multi-mineral deposit in Canada. The recovery of metals from complex base and precious metal ores may be accomplished using chloride ? assisted high temperature pressure leaching. Finally, by way of example, the enhanced Galvanox? process for treatment of chalcopyrite concentrates using silver-activated pyrite as a catalyst will be illustrated. This process offers a viable alternative to the conventional smelting of chalcopyrite copper concentrates.

Sep 1, 2012

By Wayne R. Charley

High operating costs and environmental restrictions have combined to increase smelting costs for precious metals to a level where many mining companies cannot afford to operate. The need for a hydro-metallurgical process to produce bullion with an efficient, economical and environmentally safe method is well recognized by the industry. This paper describes the research and development program conducted by Behrent Engineering Company in its investigation of the use of an acidic solution of thiourea for the extraction of precious metals from concentrates and high-grade ores. The areas discussed are: process design parameters, health and environmental aspects and economics of the process. The scope of this paper includes the leaching process, the recovery of precious metals from pregnant solutions and the production of dore'. Thiourea leaching offers a complete alternative to smelting and cyanidization for those concentrates and ores amenable to this process.

Jan 1, 1984

By Niels Verbaan, Ralph Fitch, Charlotte Forstner, David Dreisinger

A process has been developed to extract gold, silver, indium, gallium, lead, copper, zinc, and other metals from a large resource using an oxidizing acid chloride heap leaching technology. The ore is crushed and/or ground to improve reactivity and then contacted with a solution containing NaCl-HCl-NaOCl. The value metals are leached into solution as chloro-complexes. The leachate is treated in a series of separation and recovery processes to produce separate saleable or disposable products. The paper will provide a summary of process development and application to a silver-indium ore from Bolivia. The possible application of the process to other ore types will be presented for discussion.

Jan 1, 2015

By Rick Honaker

Rare earth elements (REEs) contained in coal and associated mineral matter exist in several forms including micro-dispersed minerals, ion adsorption onto clay surfaces, and chemically bound. Tests found that REEs can be effectively recovered from certain components of three coal sources by leaching under mild conditions followed by solvent extraction. A range of pH values were evaluated at solution temperatures of 25 and 75 °C. When using 1.2 M of sulfuric acid, nearly 85% recovery of the REEs was extracted from the middlings material collected from an operating plant. Acid leaching of a second middling source from another plant resulted in 60% of the total REEs being recovered under the same leaching conditions. Solvent extraction treatment of the leachate produced from six different coal sources resulted in products containing up to 50% total REEs from feedstocks starting with around 300 ppm.

By Y. Yang, S. Peelman, J. Sietsma, Z. H. I. Sun

The rare earth elements (REEs) present in the Kiruna iron ore mine tailings are being considered as a new REE resource for the EU. These tailings, after beneficiation, contain approximately 5000 ppm of rare earths, concentrated in apatite and monazite minerals. To economically extract the REEs from these tailings the phosphorous contained within the apatite must also be extracted and the waste production of the process should be minimal. To achieve the extraction of REEs and phosphorous HCl and HNO3 were investigated as possible leaching agents. Based on the results a leaching process using HNO3 is proposed. This process produces H3PO4 from the apatite while simultaneously dissolving the REEs. The resulting leach liquor is then cooled to remove the unwanted Ca as Ca(NO3)2. Analysis of the leach liquor reveals extraction ratios of between 75% and 100% for the heavy REE (e.g. Y, Eu, Dy, …) and below 40% from the light REEs (i.e. Ce, La). Full phosphorous extraction was also achieved.

Jan 1, 2016

The alkaline ethylenediamine tetra-acetic acid (EDTA) leach process for extracting tungsten from scheelite (CaW04) ores has been examined for the treatment of low grade (<0.5 per cent WO,) residue dumps. The process has been considerably simplified by applying solvent extraction directly to the leach liquor.Ammonium paratungstate is thereby produced in a one step process and this obviates the need to physically recover EDTA prior to recycling. This modified process should be an economical method of tungsten extraction.

Jan 1, 1983