Search Documents

By David Pentz, Paul Hodges

GENERAL INTRODUCTION The object of this paper is to discuss those aspects of open pit mine design which are affected by geotechnical factors. The temptation exists for some practitioners of geotechnical engineering to believe that this relatively new engineering discipline is the ‘be all and end all of mining.’ In the opinion of the authors, this is fallacious but, as our ability to put numbers to the behaviour of rocks and soils improves, it is clear that geotechnical engineering will become an integral and important part of designing and operationg mines success- fully. Open pit mines in the context of this paper also includes open cast mines, where the 'ore" is extracted and the waste material is immediately replaced or ' backfilled in the mined portion of the pit. Open pit mines operating today move from very small tonnages a day to in excess of 400,000 tons per day. Several mines are operating and are being designed to capital expenditure for such projects in some cases exceeds five hundred million dollars and in a few cases will exceed one billion dollars. The size of this investment means that financing will have to be provided from banks or joint partnerships. This financial environment means that planning will be carefully scrutinized by experienced representatives of financial institutions or other mining companies. All too often a project has been put in jeopardy because the personal desire of one or two men to make a project proceed has caused incomplete planning or perhaps in some instances deliberately leading observers 'down the garden path.’ In our opinion the day is rapidly arriving when the quality, logic, practicability and completeness of the planning will make the difference between securing financing or not and, in the cases of existing open pit mines, of the difference between survival and closure.

Jan 1, 1977

By Louis A. Panek

INTRODUCTION Block caving is distinguished from other types of mining in its requirements that the mineral body to be extracted must cave after a relatively large tabular open¬ing is created underneath it, and that the caving must be predictable and controllable for both operating and safety reasons. A mineral body that caves readily may present special problems with respect to ground support in the mining access openings, where stability, rather than failure, is the desired objective. The complete ex¬traction of a caving block, which may measure 50 to 100 m on a side and 100 to 300 m in height, tends to create a large void, resulting in significant changes in the ground stress system and a migration of rock from all directions toward the void; these events begin very early in the life of the mine and lead to additional spe¬cial problems with respect to control of ground move¬ments in the mine working areas, in the rock adjacent to the caving stope, and on the subsiding surface above the mine. Thus, the mechanics of an undercut-cave operation involve a broad range of geotechnical subject matter, including the determination of the lithostatic earth stresses, the structural properties of a large jointed rock mass, the flow properties of the fragments after caving, the stability of tunnel-like openings, and the stability and displacements of the rock structure (1 to 2 km in size) that surrounds the ore body. The objectives are achieved by in-place measurement of rock properties, laboratory tests, theoretical structural analyses of the related prob¬lems, measurements of structural behavior in and above the mine, and comparison of theoretical predictions with actual performance in order to interpret and refine the predictive capability. Undercut-cave mining (Julin, et al., 1973) differs from most other methods in that the caving is an essen¬tial and inherent part of the excavation process and in¬volves the movements of millions of cubic meters of rock over distances of hundreds of meters, as compared to the gradual 2-m settling of the overburden typical of full¬caving longwall coal mining. Undercut-cave mining may involve a rock mass on the scale of a 1-km diam open¬pit mine, but mining is several times deeper than that in the open-pit mine; furthermore, a large portion of the rock mass is in a failed, rather than a stable, state. Ground-control problems are inevitable in a situa¬tion where ground movements are occurring on such a large scale, and where the rock mass is expected con¬veniently to cave at one location but to be stable at an¬other. To devise effective responses to these ground¬control problems, one needs to know first of all what is happening, not merely at the point where the symptoms are observed, but more broadly with respect to the be¬havior of the entire mine rock-mass structure over the total area of extraction, including the effects on the sur¬face as well as those underground. Monitoring structural behavior on this scale would require a sizable group of people, if they attempted to measure all the significant mining-induced changes of ground displacement and pressure, even on a 100-m grid of points. The practical approach is to conduct the mea¬surements activity by a judicious sampling, making in¬termittent, concentrated efforts in selected areas of lim¬ited extent to study problems of immediate importance; simultaneously a minimum level of surveillance is main¬tained over the total structure to delineate long-term be¬havior trends in the major structure, which provide the baseline reference data that are so essential for interpre¬tive purposes. Mine-structure behavior depends not only on the mine extraction configuration and sequence, but on the rock structural properties and how they change from one location to another in the mine. Increasing attention is being given to determinations of rock strength and de¬formation by performing mechanical properties tests in place and in the laboratory, and by drawing inferences from the mapping of geologic structure in mine openings as they are driven and from the logging of cores ob¬tained from exploration drilling that may be performed primarily for delineating ore reserves. Monitoring of mine-structure behavior and inter¬preting it in terms of the growing excavations and the structural properties of the rocks have significant im¬pacts on designing the major undercut-cave operations of undercutting and drawing the ore, supporting the ac¬cess openings, and controlling surface subsidence. The purpose of this chapter is to call attention to the com¬mon ground-control problems encountered in undercut¬cave mining, to relate them to the mining process, and to explain the geomechanical approaches to analyzing these problems with emphasis on methods that are most readily available to the mine staff. UNDERCUTTING, CAVING, AND DRAWING A distinguishing characteristic of an undercut-caving method of extraction is the objective that the rock mass fails of its own weight in a predictable and controllable manner, after it is undercut by excavating a tabular¬shaped void, horizontal or inclined. Induced or forced caving refers to procedures that may be resorted to when the ore will not self-cave over the desired span. Block caving, panel caving, and mass caving are terms used to denote the particular sequence of undercutting and ex¬tracting the total area of the ore body on a single min¬ing level. The discussion herein is not specialized to any of these variations; the word block as used does not imply anything as to sequence. CREATING THE UNDERCUT A common undercutting method is to drive a series of drifts and blast the intervening pillars. Theoretical structural analysis and practical experience show that ground-support problems in the undercutting drifts and in underlying access openings as well (the same princi¬ple applies even if undercutting is done by belling out drawpoints from the slusher drifts) are minimized by retreat-mining across the undercut slot according to a sequence such that the growing undercut area retains a

Jan 1, 1982

By M. K. Larson

The U.S. Bureau of Mines and Cyprus Shoshone Coal Corp. conducted a study of deformation mechanisms in strata around a longwall gate road system at two sites in an underground coal mine near Ham, WY. Of particular interest was timedependent (on the order of several months) roof deformation. Strata above and below the coal seam are very weak, carbonaceous mudstones that have cohesionless planes of weakness oriented along bedding, which dips approximately 8° to 16° at N 49° E. An extensive array of instrumented roof bolts, roof extensometers, and biaxial stressmeters were installed during development mining at these two sites under variable depth of cover [I83 to 335 m (600 to 1,100 ft)], seam dip (10° to 16°), and top coal thickness [estimated to be 0.30 to 0.61 m (1 to 2 ft) on the downdip side of the entry]. Bolt load and roof deformation histories during the entry development periods were compared. Bolt loads at site 2 were less than those at site 1, which is consistent with the amount of overburden. Deformation magnitudes at site 2 were similar to those at site 1, but deformation rates were approximately 44% greater and nearly constant over time, whereas the deformation rates at site 1 decreased exponentially over time. Also, most deformation occurred above the bolt horizon at site two, but extensometer measurements at site 1 showed that a significant amount of deformation occurred within the bolt horizon. The most significant factor that influenced bolt tension and timedependent strata deformation was strength and Young's modulus of the strata. Finite-difference models support this conclusion.

Jan 1, 1996

By Roger S. Jackson

"This study interprets vibrations produced by single underground shots, recorded on surface by 135 digital seismographs laid out in four linear arrays. Several vibration anomalies were observed and are investigated. A novel method of displaying the blast-induced vibration iso-contour data relative to the three-dimensional representations of the geological rock units and structures leads to the following interpretations:• The identified faults commonly dampen or amplify vibrations, on the evidence of the peak particle velocity,• Strong anisotropy of geologic formations produces different vibration attenuation in the various directions of interest,• Low-vibration “depressions” can be related to the presence of faults, and• Higher vibration levels than expected based on ‘scaled-distance’ principles are observed close to intersecting faults.The interpretations from this study document a better understanding of the geotechnical influences on blast induced stress wave propagation in a geologically complex area. The practical benefit of this understanding is better control of surface vibrations, experienced from underground mining activities."

Jan 1, 2010

By Mules GJ

Geotechnical investigations have played a key role in influencing decisions for development of the Porgera Gold Project in the highlands of Papua New Guinea. Porgera is located 130 km west-northwest of Mt. Hagen in steep mountainous terrain with high rainfall. Much of the site is underlain by weak mudstone of the Chim Formation and creeping colluvial soils. Landsliding is common on the steeper slopes and in the valley floors. Structures have had to be sited to avoid areas susceptible to these movements. Early stage feasibility investigations included studies of tailings dam and waste rock dump sites, processing plant sites and hydroelectriic schemes. Further studies, leading into the design stage included the Enga Highway upgrading, water supply and power supply schemes. As construction for the project proceeds geotechnical input remains at a high level, with emphasis now on maintaining viable stable sites and refining data on which designs were based.

Jan 1, 1990

By A. Daouadji, P. Cazes, S. Grange, L. Briançon, R. Milane

Construction in congested urban areas is often accompanied by geotechnical problems due to high loads and the impact caused by nearby buildings. For this reason, it is important to understand the behavior of the soil and the structure without forgetting the essential role of the interaction between them. Experiments, instrumentation and numerical modeling are the main methods used to study this behavior. To this end, pressure cell, strain gages, vibrating wire extensometers and optical fiber sensors are installed on the reinforcement steel of pile and raft foundations to monitor stresses and induced deformation in these elements during and after construction. A fiberglass rod extensometer is placed in the soil to help measuring the displacement due to excess loading, knowing that the pile foundations are embedded in the Rhône’s alluviums and reach the molasse, a particular and challenging soil with properties that are not yet well understood. The objective of this paper is to present the geotechnical instrumentation program carried out for the tower Silex2 in Lyon, France, and to describe the types of sensors used and their installation on site. INTRODUCTION The complexity of geotechnical structures like dams, bridges or high-rise buildings requires a sound understanding of the behavior of the soil, the structure itself and the interface. Therefore, a geotechnical instrumentation program can be essential in many ways. During the site investigation stage, it can help determine the initial conditions experienced by the soil in the field by measuring parameters such as the compressibility index or the permeability. During the construction stage, real time measurements can protect the structure from premature failure, help validate and optimize the design if needed. In addition, sensors measuring pore-water pressure, loads, deformations and settlements allow for monitoring the performance of the structure. This is called the observational method. Finally, during the operating phase, instrumentation aims to study the long-term behavior of the structure (Nicholson et al., 1999).

Jan 1, 2019

By H. Maleki

This paper recognizes the 100th year of research accomplishments by the mining industry resulting from close cooperation among mining companies, geotechnical consultants and researchers from the former United States Bureau of Mines in stability assessments and development of improved and productive mine designs. The paper provides an overview of dramatic developments in geotechnical instrumentation, and its applications in the U.S. and around the world for enhancing the understanding of ground response to mining-induced changes in stress, resulting in improvements in ground control technologies.

Jan 1, 2010

By Michael Schultz, Gregory Sanders

In 2017, the North Texas Municipal Water District (NTMWD) initiated the design of the Sister Grove Regional Water Resource Recovery Facility (SGRWRRF) to provide additional treatment capacity for future population growth within the Lavon Lake watershed. To provide a discharge location for SGRWRRF approximately 4.5 miles of 2.4- meter (96-inch) internal diameter pipeline will be constructed, including 2.3-kilometer (7,800) feet and 487-meter (1,600 foot) long tunnel segments. This paper will discuss the anticipated geology of the two tunnel segments, selection of the tunnel alignment, the anticipated initial tunnel support requirements and other aspects of the project design

Jun 13, 2021

By Madan M. Singh

Currently longwall coal mining operations require at least 3 entries on both the headgate and tailgate ends because of ventilation and safety requirements. Driving of entries, however, is a slow and costly process. Often it is a bottleneck in longwall development. Single entry gateroads are permitted in Europe and commonly used there. This study entailed ascertaining the feasibility of using a single entry in the United States, without sacrificing safety. This design was conducted for an operating longwall mine in the Black Warrior coalfield in Alabama, An understanding of rock loads and consequent support requirements is prerequisite to the design and successful demonstration of the single entry system. Efforts in this regard were directed at determining center (packwall) support requirements for various single entry widths. Critical to the analysis is knowledge of the nature and extent of side abutment stresses. In collecting geological and geotechnical information relating to the stability of the single entry, Engineers International, Inc. engaged in the following: ? Examination and inspection of the single entry demonstration at the Sunnyside Mine in Utah. Severe ground conditions and unacceptable levels of entry closure were experienced there prior to the tailgate phase. Observations at the mine presented a clear perspective on possible ground control problems for future single entry designs. ? Reconnaissance inspection and classification of roof rock conditions. ? Detailed mapping of roof structure in the areas to be instrumented. ? Installation of convergence stations in the longwall headgate to monitor roof movement during mining. ? Measurement of side abutment stresses in a yield pillar in the area of the convergence measurements. ? Measurements of coal fracture distribution by the detail area method. ? Rock properties determinations of roof, coal, and floor rocks; samples obtained by core drilling. ? Determination of floor bearing capacity by in-situ testing.

Jan 1, 1982

By E. R. Wang

This paper outlines the engineering properties of shallow soil in Shanghai area. The main points that should be paid attention to during deep foundation investigation, and general conditions of experimental soil engineering are discribed.

Jan 1, 2010

By Julian Prada

Tunneling requirements are presenting designers with greater challenges. The design and construction of the 2000-ft long unidirectional twin highway tunnels for the approach to one of two bridges of the Louisville-Southern Indiana Ohio River Bridges (LSIORB) Project is no exception. Excavation under low cover, beneath an historic site, with each tunnel of 70-feet wide and 50-feet high dimensions will set precedents for US highway tunnel excavation size. To investigate ground conditions to supplement final design of the highway tunnels, an exploratory tunnel excavated through karstic limestone and shale will be located within the confines of the proposed final alignment. With the LSIORB Project, Jefferson County, Kentucky and Clark County, Indiana will have improved cross-river mobility between them. The Indiana Department of Transportation (INDOT) and the Kentucky Transportation Cabinet (KYTC) are developing the LSIORB Project jointly, in coordination with the Federal Highway Administration (FHWA). Section 4, one of six sections, as shown in Figure 1 is the East End Kentucky Approach and Connections to I-265. Key elements of Section 4 are the twin three-lane highway tunnels under the historic Drumanard Estate. The property is located on the north side of US Highway 42 (US 42) at the intersection with the Gene Snyder Freeway (also KY841) as shown in Figure 2. One aspect of the project consists of the excavation of an Exploratory Tunnel along the southbound alignment tunnel. At the time of preparation of this paper, KYTC has not awarded the Exploratory Tunnel Contract. This paper will focus on the planned geotechnical investigation program that will occur during excavation of the exploratory tunnel and how the design of the twin highway tunnels will incorporate the findings to achieve an innovative and efficient configuration.

Jan 1, 2008

By Lawrence P. Goldfarb

This paper presents the results of the geotechnical investigation for the repair of the Fashion Island Boulevard Bridge, Bridge No. 350160, in San Mateo, California. The concrete, precast girder bridge suffered considerable damage during the Loma Prieta earthquake. The existing 36-inch, precast, prestressed concrete piles cracked and spalled at their tops. Based on analyses performed by Biggs Cardosa Associates, structural engineers, the piles did not have sufficient strength and ductility to resist the dead plus seismic loads specified in the Caltrans "Bridge Design Specifications". Additional support for the bridge was needed and the repair strategy consisted of installing large diameter pipe piles at the existing bent and abutment locations. This paper describes the geotechnical engineering analysis and design decisions for the large diameter pile design.

Jan 1, 1993

By G. Avolio, M. Gilbert

INTRODUCTION The city of Alexandria, Egypt is located on the Mediterranean Sea at the northwestern edge of the Nile River delta. The city is approximately 26 km long and 3 km wide bounded by the sea to the north and Lake Maryut to the south. The Alexandria Project is split into 2 phases: phase one included designs to update two existing primary wastewater treatment plants, five pump stations and over 75 km of sewer pipe, 18 km o f which is tunneled, (1500mm to 2750mm ID pipe). Currently the pipeline and pump stations are under construction. Phase two of the project includes expanding both the capacity of the treatment plants and the limits of the collection system. Included in this system expansion is the 3.5 km long, 2250mm ID Central Zone Conveyance, which is the subject of this paper. The project is under the direction of The Alexandria General Organization for Sanitary Drainage (AGOSD). It is an USAID funded joint venture of two American firms, CH2M - Hill and Metcalf & Eddy who share equally the major portion of the work and two Egyptian firms, Engineering Consultants Group (ECG) and Wairth Associates who are also partners. The venture, which is both design and construction management, worked under the name Wastewater Consultants Group, WWCG. Michael Gilbert was Chief o f the Geotechnical Department and Project Engineer for the Central Zone Conveyance. Gennaro Avolio was Geotechnical Exploration Manager for the Alexandria Wastewater Project.

Jan 1, 1987

By R. A. Puchner

The location of a decline shaft portal can have far reaching implications if the geotechnical conditions are not suited for safe and cost effective excavation. Ideally the portal should be positioned in an area where the excavation requires minimal support and the portal can be formed in reasonably competent rock. In many cases, however, the shaft is linked to an underground mining plan and the shaft may have to pass through poor ground conditions. Determining the optimal position at which tunnelling can commence i.e. the portal, is critical and requires a thorough geotechnical investigation. Methods used to acquire information for the assessment of the ground conditions are discussed in this paper. Selection of the appropriate methods is dependent on the anticipated ground conditions, the phase of investigation and restrictions due to site access and budget. Non-invasive techniques are often used during preliminary phases and invasive techniques for the detailed investigation. The methods used during each phase of investigation are discussed. Two case studies are then presented to provide examples of the investigative methods used in two different environments. The first being a flat featureless site with thick soils and deeply weathered bedrock, while the second is a mountainous site with differentially weathered rocky outcrops. Based on these cases, it is clear that an understanding of the geology and geomorphology of the site is vital to the final geotechnical assessment. Key words: Decline shaft, boxcut, geology, geomorphology, geotechnical, portal.

Jan 1, 2009

By R. A. Puchner

The location of a decline shaft portal can have far reaching implications if the geotechnical conditions are not suited for safe and cost effective excavation. Ideally the portal should be positioned in an area where the excavation requires minimal support and the portal can be formed in reasonably competent rock. In many cases, however, the shaft is linked to an underground mining plan and the shaft may have to pass through poor ground conditions. Determining the optimal position at which tunnelling can commence i.e. the portal, is critical and requires a thorough geotechnical investigation. Methods used to acquire information for the assessment of the ground conditions are discussed in this paper. Selection of the appropriate methods is dependent on the anticipated ground conditions, the phase of investigation and restrictions due to site access and budget. Non-invasive techniques are often used during preliminary phases and invasive techniques for the detailed investigation. The methods used during each phase of investigation are discussed. Two case studies are then presented to provide examples of the investigative methods used in two different environments. The first being a flat featureless site with thick soils and deeply weathered bedrock, while the second is a mountainous site with differentially weathered rocky outcrops. Based on these cases, it is clear that an understanding of the geology and geomorphology of the site is vital to the final geotechnical assessment. Key words: Decline shaft, boxcut, geology, geomorphology, geotechnical, portal.

Jan 1, 2009

By Greg Sanders, Michael Gilbert, James G. Shaughnessy

"A new raw water intake from the South Holston River to the Kingsport water treatment plant is under construction. The exploration for the 335 meter long horseshoe shaped tunnel design took advantage of the site topography along the alignment to better define the complex geology consisting of Knox Limestone and Sevier Shale formations separated by a fault zone. To assess the geological conditions and to determine the extent of the fault zone, a 183 meter long horizontal boring and geophysical investigation was performed along a portion of the tunnel’s horizontal alignment. Explorations defined the fault zone width at approximately 5 meters and packer testing along the alignment provided a means of estimating groundwater inflows. As the tunnel excavation advances, comparisons of exploratory data versus encountered conditions will be made. This paper provides details on the geotechnical investigation, lessons learned, and the influence of the geology on the tunnel design. PROJECT OVERVIEW The Kingsport WTP is supplied with raw water via the South Holston River. The City of Kingsport (City) owns and operates the Kingsport Water Treatment Plant (WTP). The existing raw water intake system, consisting of pumps, power supply, raw water piping and appurtenant facilities has been determined to be vulnerable to failure. The original Raw Water Pump Station (RWPS) was constructed in 1928 as part of the original Kingsport WTP project. The 1928 RWPS operated until 1970 when it was replaced by the existing RWPS. This existing system still utilizes the 1928 piping and piping tunnel. Improvements to the RWPS hydraulics and capacity are required to meet the City’s future water treatment needs. The system extracts water from the South Fork of the Holsten River and coveys it via three pressure pipelines to the WTP. The conveyance piping exits the RWPS, ascends approximately 23 m up a near vertical rock outcropping then enters a 120 m long tunnel. Upon exiting the tunnel the piping continues underground to the WTP. The drill and blast tunnel is horseshoe shaped and nominally 3.3 m high by 3.3 m wide. The easternmost 62.3 m of the tunnel is without any type of support. The remainder is lined with concrete. According to the City of Kingsport, the concrete lining was installed in the 1970’s as part of upgrades to the facility. An evaluation of the current facilities concluded that the conveyance piping was in poor condition and required replacement."

Jan 1, 2016

By Parker RJ, Swindells CF

The authors have used the geotechnical study for design of the South Wall of Mt. Newman Mining's Mt. Whaleback Mine to illustrate how geotechnical studies can be economically justified. This is achieved by relating the savings resulting from increased ore recovery and prevention of failure to the cost of the study. An outline of the geotechnical study is provided in the paper, including a brief description of the innovative methods used to investigate geological structure of the mine and descriptions of the methods of slope reinforcement adopted.

Jan 1, 1986

By Barrie T. Wells, Raghu N. Singh, Paul S. Buddery

Rockbolting and dowelling are important methods of ground control. Their effectiveness depends upon the compatibility of the support members and the geotechnical behaviour of the rock mass. Detailed geotechnical investigations are, therefore, necessary for the design of effective rockbolting systems. The study described in the paper was concerned with improving the effectiveness of ground control at Mount Isa Mine. The paper briefly reviews the design methods avail- able when choosing a rockbolting system with a view to identifying the most suitable method. Joint surveys were used for the geotechnical assessment of rock mass stability. These were interpreted with the aid of the stereographic technique of predicting the size and shape of potentially unstable blocks of rock in both the roof and side walls of excavations. The geology and ground conditions at Mount Isa are briefly described together with the current ground control techniques. The requirements for ground control have been investigated at representative sites by analysing typical modes of rock failure and using a geological predictive technique. An application of this technique to the selection of a support system in a shallow Coal Measures tunnel is also described. The paper concludes with a general discussion on the effectiveness of this method of site investigation for the appraisal of rockbolting support in mining and civil engineering excavations.

Jan 1, 1983

With increasing depth of mining, geotech nical factors assume increasing importance in the design and operation of open pit coal mines. Dragline strip mines are particularly sensitive to stability conditions since the draoline is a relatively inflexible machine, particularly in relation to its limited dump- ing radius for overburden disposal. Geotechnical factors relevant to strip mine design include: 1. spoil pile stability 2. wall stability 3. floor stability 4. excavation characteristics 5. groundwater conditions A basic geotechnical investigation pro- gram for new mine feasibility studies is described. This includes: 1. terrain evaluation 2. geotechnical drilling and logging 3. geophysical logging 4. materials testing 5. seismic refraction traversing 6. groundwater studies Such a program will give an overall geotech- nical assessment of the site and highlight any areas which may require further, more detailed Investigations

Jan 1, 1981

By Earle J. Klohn

INTRODUCTION The paper presents a broad overview of the geotechnical site studies required for siting uranium tailings dams. These studies, which are interdisciplinary in nature, touch upon such related fields as: hydrogeology, hydrology, and seismicity. Tailings dams are commonly used to develop tailings ponds for the storage of the waste products generated by mine milling operations. In the past, most tailings ponds have been developed either above ground on dry land, or in existing lakes. In the United States a majority of the uranium mines are located in arid or semi-arid regions and past practice has been to store the wastes above ground on dry land (1,2). Currently, the United States Nuclear Regulatory Commission (N.R.C.) recommends below ground disposal of uranium waste products, although they indicate that they will consider above ground alternatives (3). In Canada many of the existing uranium mines are located in a wet environment and past practice has been to use small lakes and depressions as tailings ponds (1,4). However, current practice in Canada leans towards above ground, dry-land storage (5,6,7), and the Atomic Energy Control Board (AECB) guidelines (5) indicate this to be the preferable method. In B.C., where a moratorium on uranium mining has been declared by the Provincial Government, there are no existing uranium tailings ponds. However, both the formerly proposed Birch Island and Blizzard uranium developments would have used dry land storage. Most of the existing non-uranium mill wastes in B.C. are stored behind tailings dams on dry land. The waste products delivered to the tailings pond comprise, the ground-up rock that remains after most of the uranium values have been removed and the excess chemicals used in the milling process. These waste products, which are called "tailings", are normally mixed with water to produce a slurry and then pumped to the tailings pond. Since the uranium recovered constitutes only a small percentage of the ore (usually less than 1%) (8), large quantities of waste rock and associated transportation water are discharged into the tailings impoundment area. Consequently, relatively large tailings pond areas are required for the uranium tailings. In recent years, major advances have been made in the design, construction, and operation of non-uranium tailings storage facilities (9,10,11,12,13,14, 15). These improvements have been based on combining the latest advances

Jan 1, 1980