Search Documents

By O. Neves, C. G. González Beca, M. C. Sol Pereira, H. Sousa Vale, R. A. Guedes de Carvalho, M. N. Sampaio

"As sulphide ores are usually concentrated by flotation , the material is very finely ground <37um), wet and impregnated with the chemicals used in flotation. These conditions are favourable to the development ofchemical reactions which are largely influenced by atmospheric conditions (temperature, humidity, wind, etc.) as well as by the geometry of the piles.Physical and chemical properties of a chalcopyrite concentrate were determined by laboratory tests. The knowledge of these properties was considered necessary in order to establish a correct design of the storage and handling operations of the sulphide ore concentrates obtained by flotation.The properties studied in this work were: transportable moisture limit, flowability, effects of vibration, hygroscopicity, ""caking"", chemical alterations by humidity, oxidation and self-heating (auto-ignition, dry and wet oxidation, self-heating by humidification and its prevention).INTRODUCTIONIn order that the handling and the transport of a powdered material may be carried out correctly, it is necessary to know certain physico-chemical characteristics. Transportable moisture limit (TML), apparent density (both aerated and compacted), compressibility, angle of repose, angle of spatula, cohesion and angle of slide(l-4) are characteristics (among the flowability parameters) worth knowing.Moisture content of the powdered material is fundamental, because if this is too low heavy losses will occur when the product&apos;s particle size is very small, if it is too high, separations between solid and liquid phases may occur. In the latter case, the centre of gravity of the system may change suddenly and cause accidents, mainly if transport is by sea or by river."

Jan 1, 1989

By J. R. Schafler, J. L. Brinkman

"The US coal mining industry has suffered a recent decline in profits caused by a combination of decline in commodity demand and more restrictive government regulation, forcing coal mining companies to cease production in numerous mines. A 40% decrease in the total number of coal mines occurred from 1994 to 2000. The number of mines remained relatively constant until 2008 when a change of government sparked a series of new environmental regulations which have contributed to another 15% decrease from 2008 to 2016. In contrast, production has only decreased by 3%, increasing from 1994 to 2008, and then decreasing since 2008. However, this value is skewed by large increases in sub-bituminous coal production and decreases in other coal ranks. Several aspects assist in executive decisions on mine longevity and economic worth. Studies of open source mine data collected by mandated government surveys coupled with commodity history can be used to find relationships between mine closures and these elements, which include statistics on production tonnage, seam height, coal rank, etc. This paper looks at coal mining trends since 1994 by comparing mine, market, and regulation factors that may influence mine closure. INTRODUCTION The US coal mining industry is currently experiencing a decline in both demand and commodity price while facing implementation of more stringent air and water pollution regulations. Company profits have decreased significantly, forcing several major companies to declare bankruptcy. The industry was required to adapt to survive. Many of these companies have adjusted by abandoning mines; the last two decades have seen a drastic decrease in the number of mines. To discover the primary causes of this downturn, three major aspects must be studied: properties of abandoned mines, commodity history, and regulatory impact. TRENDS SINCE 1994 Each year, US coal mines are required to submit data on a wide variety of categories to the Mine Safety and Health Administration (MSHA) and the US Energy Information Administration (EIA). This data includes administrative records, production values, and information regarding the attributes of the mined material and the mine itself. Each year since 1996, EIA has released a report summarizing the data from two years prior. Additionally, MSHA maintains a database containing a collection of all the most current data. These resources are the primary sources for the following figures."

Jan 1, 2017

By D. F. Malan, T. E. Oates

A recent experimental pillar extraction project at a UG2 bord-and-pillar mine presented a unique opportunity to compile a new pillar database. Currently, the South African hard rock bordand- pillar mines are designed using the Hedley and Grant formula with a modified K-value. This empirically derived formula was developed for uranium mines in the Elliot Lake district of Canada. The use of this formula for the design of pillars in South Africa is questionable. Very few pillar failures have nevertheless been observed and its current calibrations for the various reef types are possibly too conservative. A new UG2 pillar database of 66 pillars, of which seven are classified as failed, was compiled by the authors. This enabled a revised ‘first-order’ calibration of the K-value for the Hedley and Grant formula. The new estimated value for the UG2 is K = 75 MPa. This gives a pillar strength that is more conservative than the PlatMine formula. This work should nevertheless be considered as only a preliminary calibration as the database was small. Further work is also required to determine whether the exponents in the formula for the width and height parameters are appropriate for UG2 pillars.

May 3, 2023

By Jay R. Schafler, Jacob L. Brinkman, Catherine E. Johnson

"The United States coal mining industry is currently experiencing a decline in both demand and commodity price while facing implementation of more stringent air and water pollution regulations. Company profits have decreased significantly, forcing several major companies to declare bankruptcy. The industry was required to adapt to survive. Many of these companies have adjusted by abandoning mines; the last two decades have seen a drastic decrease in the number of mines. To discover the primary causes of this downturn, three major aspects must be studied: properties of abandoned mines, commodity history and regulatory impact. Trends since 1994Each year, U.S. coal mines are required to submit data on a variety of categories to the U.S. Mine Safety and Health Administration (MSHA) and the U.S. Energy Information Administration (EIA). This data include administrative records, production values and information regarding the attributes of the mined material and the mine itself. Each year since 1996, EIA has released a report summarizing the data from two years prior. Additionally, MSHA maintains a database containing a collection of all the most current data. These resources are the primary sources for the figures included in this article. There are several items to note regarding this data:1. The EIA reports from 2016 and 2017 were not released at the time of writing this report.2. The MSHA data set is actively maintained as information is provided. This means the data for 2016 is from June 27, 2016 and data for 2017 is from Aug 24, 2017. All other points represent the end of-year values.3. Each of the figures only includes data pertaining to active mines. EIA defines active mines as both active and temporarily idled mines, and inactive mines as nonproducing and abandoned mines. MSHA separates all four into separate categories, though this paper combines the MSHA values according to the EIA definition for the purpose of comparison."

Jan 10, 2017

By Carlos Torres, Albert Cabrejo

For the last 20 years mine slopes have been monitored with slope stability radars. Since 2015 a group of dedicated geotechnical engineers dedicated to remotely monitor radars around the world have detected 2000+ slope failures of different characteristics. A statistical analysis of the information gathered of these failures have been made and the summarized results are presented with some degree of analysis appropriate for the vastness of the database. The analysis considers different types of commodities, countries, mining processes, rock types, and weather conditions.

Sep 29, 2023

There are some problems in the beneficiation of fine-grained oxidized iron mineral such as high cost, severe sliming, poor results and low recovery due to the fine disseminated size of the mineral. Taking several representative types of finely-disseminated oxidized iron minerals as examples, the author analyzed the main difficulties in the beneficiation of such kind of ores and discussed the existing problems in grinding-classification, technological process, flotation reagents and separation equipments and the resolvents of these problems.

Jan 1, 2014

By Shilpa S. Haramkar, Bhaskar N. Thorat, Sachin V. Jadhav

The filtration of phosphogypsum is a ubiquitous step in the manufacturing of phosphoric acid. It is highly desired to achieve the minimum concentration of P2O5 in the phosphogypsum cake. This work is aimed at addressing P2O5 losses in phosphogypsum (PG) along with the recovery of P2O5 from slurry by using constant pressure filtration at 1 bar pressure. Laboratory tests were carried out in the phosphoric acid production plant situated in Paradeep, India. Recycled water source near acid plant (i.e., pond water) was used for cake washing to reduce the burden on fresh water stock. The findings indicated that pressure filtration offered the most effective P2O5 recovery (nearly 93.48%). The moisture was reduced to 14–16%, and watersoluble P2O5 in the gypsum cake was found to be negligible. A narrow particle size distribution was observed, which offered effective filterability with average cake resistance of 2.38 × 1010 m/kg, indicating a moderately separable cake.

Aug 23, 2023

By W. Griffith

"While oxalic acid precipitation practices are commonly applied on purified rare earth elements (REEs) pregnant leaching solutions (PLS), few efforts have been reported using oxalic acid (OXA) to recover REEs directly from untreated PLS. High oxalic acid demand is the most significant issue in all these direct oxalic precipitation (DOP) practices. Preliminary research on DOP of REE from a dilute PLS originating from an acid bake followed by water leaching was conducted. At 75°C, the oxalic acid demand was between 12 and 18 times the stoichiometric requirement for complete REE precipitation. Conducting DOP at 25°C had superior REE recovery but the product purity and filterability declined. Between 75°C and 100°C, REE recovery increased with increasing temperature. When sodium hydroxide was used to adjust the pH during DOP, in the range of 0.5 to 1.5, higher pH benefited REE recovery. Using ammonium hydroxide in place of sodium hydroxide, the REE recovery was reduced by close to 5%. Sodium chloride addition to the PLS was also investigated and the results showed that at both 75°C and 25°C, the REE recovery was enhanced substantially. At 25°C, when the oxalic acid addition was controlled at 4.7 times the stoichiometric requirement, the overall REE recovery reached 95% with the addition of 240 g/L NaCl. Other reagents such as KCl, NH4Cl also showed significant enhanced REE recovery at the same oxalic acid addition. The addition of sodium sulphate appeared to largely enhance the precipitation of LREE but inhibited the formation of HREE oxalate. All results indicate the formation of rare earth double salts may play an important role in REE DOP sulphate media.INTRODUCTIONThe conventional routes for recovering rare earth elements (REEs) from a sulphuric acid pregnant leaching solution (PLS) involves an initial purification step for removal of iron, aluminium for example by precipitation through neutralization, followed by precipitation of REEs as hydroxide, oxalate or carbonate salts, or by bulk solvent extraction for REE recovery (Xia, 2013). Another route was used by Bayan Obo in their historical flowsheet, where the PLS was first subjected to double sulphate precipitation, then the remaining REEs, mostly heavy rare earth elements (HREE), were recovered by oxalate precipitation (Li, 2011)."

Jan 1, 2016

By Kihong Park

A hygroscopicity tandem differential mobility analyzer (HTDMA) technique is used to determine size-effect of nanoparticles (NaCl, (NH4)2 SO4, KCl, NH4NO3, MgCl2,CaCl2) on their hygro­scopic properties (deliquescence relative humidity (DRH) and hygroscopic growth factor (GF)). The HTDMA system uses a combination of two nano DMAs and two regular DMAs to measure particle size change in a wide dynamic particle size range. Particles are subsequently analyzed with a transmission electron microscopy to investigate the potential effect of particle structure or morphology on the hygroscopic properties. We found that structural properties of NaCl and (NH4)2SO4 particles also play an important role in determination of the DRH and GF and are more pronounced at smaller diameters. Data show that the DRH of NaCl nanoparticles increased from *75% up to *83% RH at 8 nm and that their GF decreased with decreasing size. The extent to which the GF of NaCl nanoparticles decreased with decreasing size was greater than theoretically predicted with the Kelvin correction. The GF of furnace-generated NaCl nano­particles that have pores and aggregate shape was found to be smaller than that of atomizer-generated particles that are close to perfectly cubic. For the case of atomizer-generated (NH4)2SO4 nanoparticles, we observed no signi?cant size-effect on their DRH, and the measured GF agreed well with predicted values using the Kelvin correction. For furnace-generated (NH4)2SO4 nanoparticles, a gradual growth at moder­ate RH without noticeable deliquescence behavior occurred. Their TEM images showed that contrary to atomizer-generated (NH4)2SO4 nanoparticles the fur­nace-generated (NH4)2SO4 nanoparticles are not perfectly spherical and are often aggregates having pores and holes, which may favor holding residual water even in the dried condition. For atomizer-generated KCl, MgCl2, and CaCl2 nanoparticles, we observed no signi?cant size-effects on their DRH and GF for the mobility size as small as 20 nm.

Jan 1, 2008

Grinding and energy input in stirred media mills are studied as functions of grinding time, stirring speed, media size and density, solid concentration, impeller and tank dimensions and design, and other relevant variables. Ground product size and surface area are determined with respect to the above variables. Changes in energy input and media/pulp rheological properties during grinding are described. The best conditions for grinding limestone in the laboratory stirred media mills have been identified. Equations for correlations involving power and modified Reynolds numbers have been established.

Jan 1, 1995

By Bowang Xiao

Recently more and more attentions are paid to high pressure hydrogen quenching (HPHQ) for its advantages such as environmental friendliness, low distortion, etc, compared to oil and water quenching. In HPHQ process, heat transfer coefficient (HTC) usually varies from part surface to surface because of the intense variation of gas velocity around the part. This article studies the effect of HTC distribution on part distortion after HPHQ and shows that finite element simulations considering HTC distribution predict different distortion from these without considering HTC distribution. It is also pointed out in this article that HTC distribution can be optimized by adjusting part orientation and HPHQ condition so that part distortion is minimized.

Jan 1, 2010

By Bok-youn Kim

Presently, mobile diesel equipments contributes a lot in improving the economical feasibility of underground mining and tunneling operations. Even in Korea, quite a large number of diesel equipments is being applied to the underground workings already. This paper introduced the production procedure, characteristics and evaluation technology on diesel particulate matter(DPM) that is known as a carcinogen For easy measurement of DPM using laser dust monitor, the conversion factor(K) to gravimetric concentration was acquired. The field measurement of DPM was conducted to make a comparison between locally manufactured on-road equipments and imported equipments specially designed for underground use. According to the Government regulation revised h 1996, it was learned that the critical pollutants among the diesel exhaust is DPM instead of NOx which have been considered as a critical pollutants.

Jan 1, 1997

A Study on Main and Interaction Effects of Operating Variables of Column Flotation

Sep 13, 2010

By F. Q. Dong

According to the principle that should be originated from nature, compatible with nature, used in nature and back to nature and based on conception of designing of eco-material, the author combined the ideas of material, environment, zoology and healthy. Properties of natural mineral materials were used to produce micro-aggregate elements by bionic method, so its components and function could accord with living environment. Eco-mineral functional materials which can adjust, purify and optimize the microclimate were reviewed. The authors pointed out the multifunction, com-pounding, the compound characteristics and integration regularities of micro-aggregates. It was the first time in the world to put forward the ?gene? technique or ?material chip? technique of manufacturing function micro-aggregates and eco-function elementary materials. The results of this re-search supported by the national ?863? Hi-tech Project, mainly including the high-efficient air purifying mineral compound material indoor, the clay elementary antibacterial materials, the masonry cement/coating/putty/compound with preventing radon radiation, environmental friendly composite functional coatings, mosquito repellent and healthcare material and zeolite-based energy-saving composite materials, were introduced. Finally, the foreground of mineral materials in the field of future advanced eco-friendly materials was also discussed.

Jan 1, 2014

By Cem Colakoglu

In this study, nickel containing iron alloys were produced by carbothermal reduction of lateritic nickel ores obtained from Manisa - Caldag region of Turkiye in order to investigate the reaction mechanism of nickel and cobalt. In the experiments, the lateritic ore containing 1.58 wt.% Ni and 0.12 wt.% Co was calcined in a semi-pilot scale rotary furnace at 1100°C for 1 hour. Then, a mixture of calcined ore and metallurgical coke was reacted in sintered alumina crucibles using a graphite resistance tube furnace at different time (0- 60 min) and temperature (1500-1600°C).

Jan 1, 2009

By Babu K. V., Samyukta P.

The energy demand in India is expected to show increasing growth in the next few decades. The oil companies in India are revamping the existing oil refineries as well as constructing new refineries across the country to meet the energy demands. Most of the refineries in India are located along the coastal region because of the ease of transporting crude materials. Considering the criticality of the structures as well as soil conditions in the coastal region, pile foundations are used in refinery plants. In India, non-displacement piles in the form of bored cast-in-situ piles are used to support structures. In a few circumstances, displacement piles in the form of driven cast-in-situ piles are also being used to support critical structures. This study presents the performance of non-displacement and displacement piles for similar ground conditions at the same project location. The pile load test results have shown that the settlement observed for displacement piles is lower than compared to non- displacement piles for a given loading and soil conditions. This shows that the performance of displacement piles is slightly better in comparison with that of non-displacement piles.

Sep 1, 2022

By : D. Lawrence

Certain blasting applications are more prone to the generation of significant levels of nitrogen dioxide post blast fumes, more commonly referred to as after blast smoke, generally ranging in color from dark yellow to bright red. This paper reviews basic background chemistry defining the observed fumes and attempts to correlate geology, blast design, and explosive composition effects on the level of nitrogen dioxide that can be observed in various blasting conditions. Additionally, a test setting for evaluating the generation of post blast fumes is presented with pertinent test data detailing generic explosive formulation modifications which effect the overall level of post detonation generation of nitrogen dioxide.

Jan 1, 1996

By L D. Lawrence

Certain blasting applications are more prone to the generation of significant levels of nitrogen dioxide post blast fumes, more commonly referred to as after blast smoke, generally ranging in color from dark yellow to bright red. This paper reviews basic background chemistry defining the observed fumes and attempts to correlate geology, blast design, and explosive composition effects on the level of nitrogen dioxide that can be observed in various blasting conditions. Additionally, a test setting for evaluating the generation of post blast fumes is presented with pertinent test data detailing generic explosive formulation modifications which effect the overall level of post detonation generation of nitrogen dioxide.

Jan 1, 1996

By L. Shuyi

In order to develop the pulsating high gradient magnetic separation technology, a type of laboratory pulsating high gradient magnetic separator (PHGMS) has been manufactured. Experiments of its separating performance were carried out. They show that PHGMS can significantly increase the grade of the magnetic product and avoid the matrix to be blocked. The characteristic curve of the pulsating fluid was measured and a formula for estimating the grade of the magnetic product was established in PHGMS.

Jan 1, 1990

By Ranajit Kumar Sahoo, Shatrughan Soren, Surendra Kumar Biswal, Soumya Sahoo, Sachida Nanda Sahu

The presence of appreciable quantity of clay mineral in Indian hematite ore needs an attrition technique using screw scrubber in the beneficiation circuit to remove the ultrafine clays and avoid downstream operational problems. Spectroscopic analysis revealed that iron ore samples obtained from the Barbil region of Odisha contain a high amount of silica and alumina in the form of clay minerals (e.g., kaolinite) contributed as a loss on ignition (LOI) in the iron-making process. Iron ore fines of below 10 mm size were subjected to a laboratory-scale screw scrubber, and the effectiveness of scrubbing as well as the pelletization of the scrubbed product was investigated. The screw scrubber in the beneficiation circuit helps to remove the clay minerals, causes an increase in iron values from 63.65% Fe(T) to 66.18%Fe(T), with improved physical (CCS of 325 kg/pellet) and metallurgical (RDI of 2.24%) pellet properties.

Aug 31, 2020