Search Documents

By Christie GB, Mainwaring DE, Leong YK

High solids brown coal slurries have been prepared with concentrations approaching those achieved with bituminous black coals. The high inherent water content and macroporosity of Victorian brown coals have been reduced in a controlled manner by chemical and mechanical means. The hydrophobicity of the coal surface has been increased sufficiently to reduce the tendency for swelling and water uptake. This together with densification has allowed the solids content to be progressively improved from 25% solids with raw coal to 65% solids with modified coals. Both raw brown coal and modified brown coal suspensions show shear thinning behaviour resulting in lower viscosities at higher flow rates. All coal suspensions displayed a yield stress once sufficient solids concentration was achieved. This yield stress can be used in the prevention of solids settling. Under simple shear mixing the network structure that provides the yield stress quickly breaks down to a low viscosity fluid with reduced yield stress and a pumpable consistency. The time necessary for structural recovery is in the order of days permitting shut-down and start-up of fuel delivery systems.

Jan 1, 1987

By Wenjun Duan, Zhimei Wang, Tianwei Wu, Qingbo Yu

In order to recover the waste heat of molten blast furnace slag, a reactor with top-submerged lance was established. The numerical simulation and experiment study of the flow characteristic in the reactor were conducted. The mathematical model of reactor was established and the Euler-Euler model was employed to simulate the gas-liquid flow in molten slag bath. Meanwhile, the experiment results were obtained and compared with the simulation to testify the accuracy of the established model. According to the bubble behavior in bath, there were four stages: initial expansion stage, bubble detachment stage, freedom lift up stage and bubble broken stage. When the flow field in bath fully developed, the gas fraction decreased with the increasing of bath depth. During injection process, the area near the nozzle and lower the bath would first generate two symmetric heliciform flow regime, and then the flow regime in whole bath would become irregular because of bubble lifting up and rupturing. The gas fraction in bath, the average velocity and turbulence energy of slag would decrease before it increased to maximum and then it would keep fluctuate in a range.

Mar 1, 2018

By Partridge A. C

Pinched Sluices, in a variety of guises, are used extensively for the separation of minerals according to density. In the authors' work a pilot-scale sluice has been constructed with provision for splitting the discharge stream into a number of layers. The composition and flowrate of the stream can thus be analysed as a function of depth and the results presented graphically. The effects of such parameters as total flowrate, pulp composition and particle size on overall performance can be clearly seen from such data.

Jan 1, 1979

By L Barro

There is currently a worldwide interest in coal-oil technology as the search continues for alternative energy sources to reduce the consumption of petroleum crude. An important aspect of this coal-oil technology study is to obtain information on the flow properties of coal-oil slurries. While some work has been reported on the flow behaviour of black coal-oil suspensions, very little work on brown coal-oil suspensions has been reported. In this paper flow characteristics of brown coal-oil suspensions for various coal concentration and temperatures have been presented. A capillary rheometer, designed to handle settling suspension, has been used for determining rheological properties. Brown coal of 0.0725 mm average particle diameter has been used in this work. The oil was a coal derived product having a boiling point range of 234¦C - 319¦C. Apparent viscosity of all suspensions was found to increase on storage due to ageing. Ageing might have occurred due to physicochemical interactions between coal and oil. Flow behaviour of some suspensions changed from Newtonian to non-Newtonian on storage. Apparent viscosity increased sharply with increase in solids concentration and suspensions at higher concentration behaved as non Newtonian liquids. Viscosity decreased with increase in temperature; rate of decrease slowed down with increase in temperature.

Jan 1, 1980

By Barro L

There is currently a world wide interest in coal-oil technology as the search continues for alternative energy sources to reduce the consumption of petroleum crude. An important aspect of this coal-oil technology study is to obtain information on the flow properties of coal-oil slurries. While some work has been reported on the flow behaviour of black coal-oil suspensions, very little work on brown coal-oil suspensions has been reported. In this paper flow charac- teristics of brown coal-oil suspensions for various coal concentration and temperatures have been presented. A Capillary rheometer, designed to handle settling suspension, has been used for deter- mining rheological properties. Brown coal of 0 0725 mm average particle diameter has been used in this work. The oil was a coal derived product having a boiling point range of 234¦- 319¦C, Apparent viscosity of all suspensions was found to increase on storage due to ageing. Ageing might have occurred due to physico- chemical interactions between coal and oil. Flow behaviour of some suspensions changed from Newtonian to non-Newtonian on storage.

Jan 1, 1980

By Shi Wang, Hongbin Liu, Meiliang Wei, Wu Liu, Xiaojun Wang, Yuxian Ke, Xuepeng Song, Tiejun Tao

The study investigates the influence of water migration on the fluidity of fresh cemented paste backfill (CPB) with and without flocculant under variable shear rates. The research utilizes nuclear magnetic resonance (NMR), rheological tests, and scanning electron microscopy (SEM) to analyze water migration, rheological properties, and microstructure evolution. The findings reveal that water migrates to more stable states as shear rate increases, and the addition of flocculant enhances water migration and increases shear stress and apparent viscosity. The study establishes relationships between water content and rheological parameters, providing insights into the flow characteristics of fresh CPB for pipeline transportation.

May 4, 2022

By R M. Yanamandra, S K. Tripathy, N Mangadoddy, P Sudikondala, P Ankireddy

Spiral concentrator is one of the most commonly used gravity concentration devices in mineral processing. The particles are classified based on their specific gravity and size. The present work analyses the experimental and numerical investigations of the water flow field, such as fluid depth and free surface primary velocity of two high gravity spiral concentrators at different flow rates. The measurement techniques use a flow depth gauge and flow visualisation technique adapting lycopodium powder as the tracer. Flow features in terms of liquid depth and primary velocity at the free surface of the flow are captured across the trough in two different high gravity spirals. A highspeed motion camera with an imaging frequency of 5400 frames per second and 768 × 768 pixel resolution is utilised to track the tracer particles in the liquid flow on the dark surface background. Further, the two-phase flow is studied numerically on high gravity spirals based on the volume of fluid (VOF) approach utilising the RNG k-ε model and Reynolds Stress Model (RSM) for predicting the fluid flow on trough surfaces such as water depth and free surface primary velocity. The CFD predictions of the flow field for the two spirals are attempted to validate against experimental data. The high gravity spiral concentrators show lower flow depths and free surface primary velocities but steep velocities on the outer trough zone compared to that of low gravity spiral concentrators (conventional coal spirals). Among the computationally tested high gravity spirals, higher pitch and higher secondary slope design shows greater flow characteristics.

Aug 24, 2022

By M. Reda

Erosion corrosion is acceleration in the rate of corrosion attack in metal due to the relative motion of a corrosive fluid and a metal surface [1]. The increased turbulence caused by pitting on the internal surfaces of a tube can result in rapidly increasing erosion rates and eventually a leak [2]. Engineers and scientists in different disciplines have worked for many years on methods of complete protection from flow induced corrosion or partially reducing corrosion of this type, and they have proposed or applied different countermeasures [2]. The accident at the Surry-2 nuclear power plant (USA) and other similar incidents have once again disturbed the scientific-technical community. This has forced the plant operating personnel and the management to undertake wide-ranging measures in order to discover on time, assess, and monitor such cases. In these extreme cases, protective coating and even metallic bulk material coating (the substrate itself) may suffer considerably from mechanically induced damage [2]. At high velocities, the "leaching out" dissolution reaction of particular, for example, steel elements at the solid-liquid interface become the rate determining step. One practical example for the difference between erosion corrosion and flow induced corrosion is the famous steam eruption from a Japanese [3, 4] nuclear power plant cooling system at the pressurized water reactor (PWR), turbine and in the condenser-steam generator connecting pipe. The rupture occurred in the carbon steel pipe connecting the condenser and steam generator. The damage occurred in the easily eroded/corroded carbon steel at a vulnerable location downstream of an orifice plate, In general, when there is significant reduction in pipe thickness through erosion/corrosion, distinctive patterns are visible, but those patterns were not observed in this case, Thus one can speculate that another phenomenon is possibly controlling, Fluid flow within pipes reduces the pipe thickness leading to an eventual rupture, The thickness reduction mechanism is erosion/corrosion, One example is "cavitations corrosion", Erosion and corrosion occur at the same time, and it is difficult to determine which one is dominant, Therefore, the term, "erosion/corrosion," is used [5]. In the atomic energy field, the terms "Flow Accelerated Corrosion" and "Flow Induced Corrosion" are also used. It is the purpose here to show that during flow induced corrosion a different mechanism may possibly be operating and in some cases it can be different from the well known erosion corrosion. Another example is fretting failures in early Canadian nuclear steam generators which was thought to be due to excessive vibration caused by high.

Jan 1, 2010

By V Rimal, d M. Tangstad

Multiphase slags form the basis of the reduction pathway for manganese ferroalloy production. The present work aims to understand the flow of slag through the coke bed based on experimentation in controlled conditions. Synthetic slags of different basicities were evaluated for their phase composition, viscosity, and flow. The two-phase slag will have two zones: a liquid slag zone and a multiphase zone. The multiphase zone will consist mostly of a solid phase with some liquid slag between the solid particles. The multiphase part will hence have a high viscosity. The liquid zone will flow into the coke bed while the multiphase area will stay. With increasing reduction, the multiphase area will decrease in size until the solid phase is gone and the whole slag will flow into the coke bed. The effective viscosity of slag will decrease with the lowering of the solid oxide phase. The results from flow experiments confirmed that the segregation of phases occurs when slag flows through the coke bed. It is observed that the flow is dependent both on the size of the void and the viscosity of slag.

Aug 21, 2024

By M Byrne, P Newman, M Lindqvist

SomincorÆs Neves Corvo Mine, one of the largest copper producers in Europe, is currently constructing a paste backfill plant in order to replace cemented rockfill in its bench and fill stopes and possibly replace hydraulic sandfill in the drift and fill stopes. A 250 m flow loop was constructed at the mine and the flow properties of various paste blends were investigated. Cycloned tailings and total tailings were both pumped successfully as pastes and were also combined with waste rock for additional testing. The pressure losses in 102 mm and 154 mm diameter pipeline were recorded at flowrates up to 60 m3/hr and are presented at slumps from 120 mm to 250 mm. The data showed the sensitivity of paste mixtures to slight changes in consistency, confirming the need for accurate control during paste production and distribution. The flow results clearly showed the different paste behaviour between cycloned and total tailings pastes and the change in properties at low and high slumps. In addition to pressure loss data, strength testing was done on 38 mm and 82 mm diameter samples. Further strength testing is ongoing at the mine using fly ash as a supplement to cement, reducing the overall binder cost. Preliminary engineering for the underground distribution system is briefly discussed, with reference to the siting of the plant. The Neves Corvo Mine is particularly shallow and alternative methods to pumping were sought in order to ensure sufficient hydraulic head for underground distribution. The comparison of options had to take into account the capital and operating costs, the operation of the plant and the impact on the future expansion of paste fill utilisation at Neves Corvo.

Jan 1, 1998

By Propser M, Szekely J

Flow maldistribution in the iron blast furnace has been studied analytically by the use of the vectorial form of the Ergun equation and experimentally via packed columns and a cold model of a blast furnace. Experimental results are presented showing the effect on fluid flow patterns of the following types of nonuniformities in a packed bed: the increased voidage at the wall ("wall effect"), the decreased voidage at the interface between layers of materials with different sizes and shapes, and the differences in resistance to flow of bulk regions of a column with different sizes and shapes. The proposed theory is applied to the calculation of fluid flow patterns for these nonuniformities. Velocity profiles, as calculated from these flow patterns, were found to agree reasonably well with experimental measurements obtained via hot wire anemometry techniques for laboratory scale packed columns. Calculated fluid flow patterns are presented for blast furnace burdens which show how flow patterns are affected by (a) coke segregation and (b) the relative differences in resistance to flow between coke and oxide pellet layers. For the cold model study, calculated flow patterns are presented based on photographs of a given burden distribution. The velocity profiles calculated from these flow patterns were found to agree reasonably well with the velocity profiles measured from the cold Model.

Jan 1, 1975

By Andrew W. Jenike

The first significant studies of problems related to the handling and storage of bulk solids were reported at the end of the nineteenth century. Early work originated from the necessity to store large quantities of grain and was concerned mainly with pressures affecting the structural design of silos and bins. The Janssen formula (about 1898) and the work of Ketchum [1] form the highlights of that period. In more recent years, progress in mechanization, increasing plant capacities, and rising costs of labor have focused the attention of engineers on the problem of gravity flow of bulk solids. A great deal of work has been done with models, and flow patterns obtained in small scale bins have been described in several publications, for example [2, 3]. An attempt to develop a theory of flow of bulk solids was reported in 1954 [4, 5, 61 and presented to the in a paper [7] in the same year. AIME recommended the continuation of this work and, as a result, Engineering Foundation granted a sum of money to set up a Bulk Solids Flow Laboratory. Two and a half years ago the project gained the support of the University of Utah and a laboratory was set up on the campus of the University. This project is now in progress, it has received the support of the American Iron and Steel Institute and of Kaiser Engineers, Division of Henry J. Kaiser Company. The results obtained to date are summarized in this report.

Jan 1, 1959

COMPRESSED air is held in high esteem by the mining engineer as a medium for the transmission of power. The transmission, however, is accompanied by a high percentage of loss. Of the total work done by the steam cylinder'in compressing the air inthe air cylinder, less than 50% is ultimately utilized by the machines underground. These losses are due to its essential and inherent properties as a gas. One of the sources of loss is that due to transmission through the pipes which distribute the air from the receiver to the various places where it is used. As the capacity and economic design of air-compressing plant are influenced by this source of loss, it may be of interest to give an outline of how estimates may readily be made'in practice of thediameter of pipes, quantity of air discharged, and the drop in pressure occasioned.In hydraulics we have a general formula given M Rankine's "Civil Engineering" :It was suggested, the writer believes, in the first instance by D'Arcy, that this formula could be made to apply to an elastic...

Jan 1, 1918

By S. P. Burke

THE presence of gas in coal mines necessitates the use of costly ventila-tion arrangements and the use of expensive mining methods. On the other hand, the gas itself in many instances is of considerable intrinsic value, and its separate recovery might conceivably be a profitable under-taking. This paper is concerned with a study of the movement of gas in coal strata with the object of determining the laws governing gas move-ment and thus making at least a preliminary step toward the solution of the more practical problem of its control or recovery. Naturally, so important a subject has received much attention from scientists and engineers. In most cases, however, the studies have been concerned with the origin1?, the amount2, the composition3 and the method of retention4 of the gas in coal; or, from the more practical side, have been concerned with the phenomena and conditions associated with outbursts5 or explosions and their control. Numerous studies also have been made of the permeability of coal to gas6, of gas pressures measured in coal seams, etc. The authors are unaware, however, of any attempt to present a consistent or complete picture of the laws governing the movement of gas through the coal.

Jan 1, 1935

By Hara Y, Arino S, Nakamura M, Tachimori M

The theoretical and experimental studies have been done to clarify the hearth flow of iron and slag. The results of dissections show that the hearth can be treated as a packed bed of coke hav- ing good permeability with a coke-free layer at the bottom of the hearth. 3-dimensional numerical calculations of hearth flow with and without a coke-free layer are carried out, and the results are assured by a water model simulation. The influences of a coke-free layer on the iron flow and the discharge route of iron and slag are examined. The 3-dimensional flow pattern can be represented simply by the travelling time, which depends on characteristically the profile of coke-free layer and the quantity of iron in the hearth. Those flow parameters could be obtained by the results of radioisotope tracer test ( Co for iron flow, and Sc for slag flow) at several furnaces. As a result, it is found that the coke-free layer repeats the cycle of appearance and disappearance at several-month intervals. This cycle corres- ponds to large temperature fluctuation at the bottom of hearth. The relation between iron flow and skull (solidified iron, coke and deposited graphite mixed layer) on the hearth brick was studied by the model experiment and the thermal analysis based on the indications of thermocouples installed in the bottom of the hearth. If a thin coke-free layer is formed on the skull, a fast iron flow is generated in the layer, and melts away the skull. The growth and melting of skull produces the fluctuation of thermal load on a bottom brick, causing brick Damage.

Jan 1, 1981

By Walter Kauzmann

ALL viscous or plastic flow of incompressible matter is the result of shear strain; the changing shape of any body that is being plastically deformed can be completely described in terms of the shear strain occurring at each point in the body.[t] Furthermore, the relative amounts of shear strain occurring in different parts of a body under stress depend upon the relative rates of shear strain at those different points, so that if the dependence of the shear rate of any material on the temperature, shear stress, previous history, etc., were understood, the principles of plastic deformation would be known, and we could calculate how a body made of a given material, having a given shape, and subject to a specified system of forces, would change its shape with time. It may be said, then, that the problem of plasticity resolves itself into, first, the problem of the rates of pure shear processes, and second, the application of what is known about pure shear to actual cases. It is the purpose of this work to investigate the former problem -i.e., the dependence of shear rates on temperature, stress, etc.-from the standpoint of recent developments in the field of chemical-rate theory and with particular reference to the phenomena occurring in the creep of metals and in the plastic flow of crystalline solids in general. It is left for the mechanical engineer, and perhaps the expert in hydrodynamics, to deal with the problem of applications1 RESOLUTION OF MACROSCOPIC SHEAR INTO MICROSCOPIC MOVEMENTS; RESEMBLANCE TO CHEMICAL REACTIONS Just as any large body is made up of many small units, or atoms, so macroscopically observable shear is the result of many microscopic unit shear processes; just as the understanding of the behavior of large bodies demands the understanding of the atoms of which it is made, so the understanding of macroscopic shear demands the understanding of these fundamental unit processes. The study of shear from this "atomistic" point of view has made considerable progress. There has been fairly complete understanding of shear processes in gases for a long time, at least for nonturbulent flow, as a chapter on gaseous viscosity in any text on the kinetic theory of gases will prove. In recent years Andrade2 and Eyring3 have presented important theories for the flow of liquids and amorphous solids. Becker,4 Orowan,5 Taylor,6 Burgers,7 and Kanter8 have considered the

Jan 1, 1941

By Walter Kauzman

ALL viscous or plastic flow of incompressible matter is the result of shear strain; the changing shape of any body that is being plastically deformed can be completely described in terms of the shear strain occurring at each point in the body.[t] Furthermore, the relative amounts of shear strain occurring in different parts of a body under stress depend upon the relative rates of shear strain at those different points, so that if the dependence of the shear rate of any material on the temperature, shear stress, previous history, etc., were understood, the principles of plastic deformation would be known, and we could calculate how a body made of a given material, having a given shape, and subject to a specified system of forces, would change its shape with time. It may be said, then, that the problem of plasticity resolves itself into, first, the problem of the rates of pure shear processes, and second, the application of what is known about pure shear to actual cases. It is the purpose of this work to investigate the former problem -i.e., the dependence of shear rates on temperature, stress, etc.-from the standpoint of recent developments in the field of chemical-rate theory and with particular reference to the phenomena occurring in the creep of metals and in the plastic flow of crystalline solids in general. It is left for the mechanical engineer, and perhaps the expert in hydrodynamics, to deal with the problem of applications.1 RESOLUTION OF MACROSCOPIC SHEAR INTO MICROSCOPIC MOVEMENTS; RESEMBLANCE TO CHEMICAL REACTIONS Just as any large body is made up of many small units, or atoms, so macroscopically observable shear is the result of many microscopic unit shear processes; just as the understanding of the behavior of large bodies demands the understanding of the atoms of which it is made, so the understanding of macroscopic shear demands the understanding of these fundamental unit processes. The study of shear from this "atomistic" point of view has made considerable progress. There has been fairly complete understanding of shear processes in gases for a long time, at least for nonturbulent flow, as a chapter on gaseous viscosity in any text on the kinetic theory of gases will prove. In recent years Andrade2 and Eyring3 have presented important theories for the flow of liquids and amorphous solids. Becker,4 Orowan,5 Taylor,6 Burgers,7 and Kanter8 have considered the

Jan 1, 1941

By J. D. Miller

Fluid flow phenomena and therefore the flotation efficiency of air-sparged hydrocyclone (ASH) flotation are strongly dependent on the operating and design variables such as air flow rate, slurry flow rate, underflow and overflow opening areas, percent solids in the feed, reagent levels, particle size, ASH length, etc. Time-averaged multiphase flow characteristics, as deter-mined by x-ray CT and described in a previous publication, are used to understand and explain the steady-state ASH flotation of quartz. A detailed parametric study of quartz flotation by a nominal 2-inch diameter air-sparged hydrocyclone (ASH-2C) revealed the influence of these variables on the flotation response which is discussed in terms of the multiphase flow characteristics. Thus, a phenomenological description of quartz flotation has been established to assist in the further development and utilization of the ASH technology.

Jan 1, 1995

By M S. Henderson, R D. Alorro, L G. Dyer

An alternative leaching system for rare earth element recovery from monazite is under development. The initial stage utilises oxalic acid to convert the rare earth phosphate into an oxalate salt through dissolution and reprecipitation and it is the efficiency of this stage that governs the overall recovery achieved. It has previously been proposed that lixiviant consumption is the primary limitation in this process. This work further investigates a range of conditions in an attempt to further elucidate the factors influencing the achievable conversion in this stage. It has been shown that the pH may be governed by multiple reactions both consuming and producing acid (thus the mild change over time). The importance of proper mixing and potential to operate at lower temperature with only moderate impact on kinetics has also been demonstrated. Staged/sequential leaching is more effective in fresh solution as opposed to restoring the lixiviant concentration with subsequent reagent addition, suggesting some impact of solution composition. However, contrary to previous findings, subjecting the leach residue to fresh solution resulted in significant decline in leach rate and overall dissolution. This may be because a greater proportion of conversion was achieved in stage 1 in this work than in previous investigation. This may indicate that eventual passivation or the presence of some more refractory REE minerals limits dissolution. Iron dissolution was relatively consistent upon exposure to fresh solution, displaying the ability of the solution to continue to leach the goethite component of the concentrate.

Aug 24, 2022

Flow Sheet Development of Three Geographically Distinct Chromium-Bearing Ores

Sep 13, 2010