Search Documents

By G. Purcell

When coal in an oil/water slurry is ground to minus-200-mesh in a ball mill, some of the mill energy, normally wasted as heat, can be usefully recovered to help emulsify the oil. If the discharge flows onto a suitable sized trommel screen, water and ash material are rejected through the screen while coal and oil ball together to give a clean coal product. A small (6-lb/hr) continuous plant has demonstrated the feasibility and the limitations of this process for New Mexico coals.

Jan 1, 1980

By W. L. Remick

THE hydrotator coal-cleaning process was developed as an economic necessity to meet the ever-increasing demand for an inexpensive method of cleaning coal down to the sizes ordinarily referred to as "dust." As the most urgent demand seemed to be in the anthracite field, all experimental work has been conducted in that territory during the past 2 years, with the exception of a few months during the strike of 1925-26, when some experiments were performed in the Alabama bituminous fields. The first commercial plant was constructed at the Middle Creek Colliery of the Philadelphia & Reading Coal & Iron Co., Pottsville, Pa. This plant is now operating. APPLICATION The field of application of the process is: 1. Cleaning anthracite fines, ordinarily described as "slush" or "silt." Slush contains all sizes from %2 in. down to and including "dust." (Anthracite passing a 32-in. mesh is also referred to as No. 2 Barley and No. 4 Buckwheat.) 2. Cleaning sizes too fine for recovery by other methods. 3. Removal of coal from sand circulated in the Chance sand-flotation process. 4. Cleaning of bituminous sizes. from 3/8 in. down to "dust. 5. As equipment for the performance of the froth flotation process. 6. Other separating, extraction and _washing. processes which may be considered outside the realm of coal cleaning. PRINCIPLE OF OPERATION Fig. 1 shows the method of classification practised under the Hydrotator patent:1 In coal cleaning the machines are operated as "hindered settling" classifiers, the flow of solids and liquids being so controlled that the units may be combined in series.

Jan 1, 1927

"Sedimented hydrothermal precipitates of silica, now fine-grained quartz, are described from a Pb-Zn-bearing vein system. Their discrimination from the wall-accreted fine-grained quartz that is common in the shallow parts of epithermal systems is discussed. Local fine-grained (<0.3 mm) quartz accumulations occur in a suite of veins with otherwise normal drusiform and crustified infills. This sediment may fill the vein above chokes in steep segments (axial plugs), or form continuous layers within the footwall material where the vein is inclined at low to moderate angles. Pads of fine-grained sediment are deposited on the upwards-facing surfaces of wall-rock clasts and of drusiform crystals growing from the vein walls. The asymmetry of these deposits differentiates them from the more common symmetrical, crustified walllining deposits of fine-grained quartz and opaline silica, and requires a gravity-controlled, sedimentary depositional mechanism.Thin section examination shows that much of the fine-grained quartz is present as elongate prisms. The prism habit was present soon after deposition, but it is not possible to identify unequivocally the original sedimented grains. Sedimentation of vein- and wall-rock-derived detritus is also recognized. Deposition of the fine-grained sediment accompanies normal in situ drusiform growth of quartz and other vein minerals. The mammilated and spherulitic textures associated with accretion of amorphous quartz are entirely absent from the Tyndrum veins with sedimented materials. The literature on modern hydrothermal waters and physical chemistry of silica precipitation shows that precipitates of silica suspended in hydrothermal fluids are amorphous and derived from colloidal silica. It is argued that much of the suspended silica was present as quartz at the time of deposition or was converted from amorphous silica almost immediately after deposition.Hydrothermal sediments and their distribution potentially provide information on flow directions and velocity in veins. Plugs of sediment obstruct vertical flow and lead to local flows with large horizontal components. It is shown that sedimentation features occur in other deposits and can involve other minerals. If the features seen here can be scaled up to the size of major veins, they may result in up and downdip variations in mineral assemblages and abundances, which may affect grade."

Jan 1, 2007

By J. H. McCormick

THIS plant, near Marysville, Mont., was planned to treat the ore from the Piegan and Gloster mines, the latter being one of the early and famous producers of the Marysville district. When the mill was closed in 1888, treatment consisted of stamp milling, followed by pans and settlers for pan amalgamation. The extraction was evidently poor; because, a few years later, thousands of tons of tailings were re-treated by the ranchers in the valley below the mill, by the then new cyanide process, and gave a handsome profit. In 1914, the present owners, after laboratory tests and an experimental mill run, decided upon the following treatment: crushing to 40 mesh in cyanide solution, concentration, amalgamation, classification, and cyanidation of sands by leaching, and of slime by agitation and decantation in charges. The ore averaged about $7 per ton, gold and silver, the ratio of weight being 1 oz. gold to 7.56 oz. silver. The ratio of gold and silver in tailings was 1 oz. Au to 36.6 oz. Ag; the quartz vas sharp and, sandy, however finely ground, and rather difficult to slime. The mechanical &apos;equipment was a No. 5 Symons gyratory crusher; three 10-ft. Lane slow-speed Chilean mills; one Wilfley roughing and one finishing table; one submerged-type Akins classifier; five 26 by 10-ft. fir leaching tanks; one 24 by 7-ft. Dorr thickener; four 14 by 16-ft. Dorr agitators; four 6-compartment double-row zinc-boxes having compartments 18 in. wide, 18 in. deep, and 34 in. long; Johnson zinc lathe; acid and vacuum filter tanks for treating precipitate; roasting furnace; and Case tilting No. 275 crucible furnace for melting precipitate. The mill is driven by electric power supplied by the Montana Power Co. at the following rates, per kw.-hr.: 200 to 300 hp.,.0.68 c.; 300 to 500 lip., 0.61 c.; 500 to 750 hp., 0.55 c.; plus $1 per month per installed motor horsepower.

Jan 8, 1918

By W A. Peck

Raise boring is the preferred option for constructing ventilation shafts in Australia. The trend has been towards larger diameters and longer single-pass shafts, and if at all possible, reaming through to the surface. The risk of raise failures, due to missed, unforseen or latent ground conditions has therefore been increasing, along with the need for better, more confident stability assessments.While the stability of specific weak zones and structures must be assessed individually, empirical rock mass classification schemes have been successfully used for about the last 20 years to assess general raise stability; eg the McCracken and Stacey method (M&S).Unfortunately M&S, as originally documented in McCracken and Stacey (1989), did not include a database of raise diameter and rock mass conditions versus actual performance. Nor was there a procedure for assessing the risk of failure due to adverse ground conditions. Peck and Lee (2008) published an Australian database of raise bore performance. Raise diameter and ground conditions, in terms of a lower bound Qr value, were presented for 50 cases versus raise performance. This paper updates the 2008 raise performance plot with more and SRF-corrected data. McCracken and Stacey (1989) had previously recommended that additional geotechnical data should be acquired and analysed when the proposed raise plotted on the unstable side of raisebore stability ratio (RSR) = 1.3, but the Australian data used in this study also suggests that all sites with Qr Contributions and sensitivities of various rock mass parameters (RQD, Jn, Ja, Jr, Jw, SRF, time-dependent weathering/deterioration) to raise stability and risk of failure are discussed. Numerous case studies are used to illustrate issues with stability assessments.As raises can now be remotely supported using sprayed fibrecrete, questions of time-dependency are also discussed. In recent times, contiguous piles, ‘mini-piles’ and grouting have also been successfully used to presupport or otherwise improve the stability of near-surface sections of weathered, or poor quality rock masses.

Mar 21, 2011

By M. S. Moholwa, J. D. Steenkamp, H. L. Rutto

Manganese ores are the major source of manganese for the production of manganese ferroalloys. There is a gap in the knowledge of the decrepitation behaviour of manganese ores, which presents a problem in the operation of smelters. Decrepitation, which is the breakage of the ore particles upon heating, is an important quality parameter for these ores. The purpose of this investigation was to determine the extent to which South African manganese ores decrepitate during preheating in a rotary kiln. The effects of temperature, rotational speed, and particle size decrepitation were investigated. Manganese ores were heated in a laboratory-scale rotary kiln at temperatures of 600, 800, and 1000°C, and rotational speeds of 3, 6, and 12 r/min. The size ranges were +6-20, +20-40, and +40-75 mm and the residence time was constant at 30 minutes. The decrepitation index (DI) is quantified as the ratio of the mass of <6 mm particles after pre-heating to the total mass of the sample. It was found that the DIs for all ores used were proportional to the temperature and the rotational speed and inversely proportional to the particle size range with temperature being the most important parameter. Ore A was the most susceptible to decrepitation followed by ore C and ore B; this was mainly to the decomposition of kutnohorite, the content of which was the highest in ore A and the lowest in ore B.

Nov 30, 2022

By John M. Bolger, Keith E. McMaster

Excessive salt fines are undesirable in underground salt mining as they are considered a costly waste by-product. This paper describes an extensive explosive application program conducted at The Canadian Salt Company Ltd, located in Pugwash, Nova Scotia, Canada. The prime objective of the program was to reduce the quantity of fines generated from this company's underground production blasts. The program was known as the "The Fines Reduction Program".

Jan 1, 1996

By Shibu John

Rising energy demand and steadily decreasing quality of raw materials due to the global resource depletion are great challenges to the steel production today. The FINEX® Process has been developed jointly by POSCO, Korea and PRIMETALS Technologies Austria, to provide the iron making sector with the capability to lower hot metal production costs, environmental pollutions and to increase the flexibility in terms of operation and the choice of raw materials. FINEX® is a new technology combining a gas-based reduction in a series of fluidized bed reactors and a reduction smelting in a melter gasifier. Commenced in April 2007, the first 1.5Mtpa commercial plant has demonstrated the competiveness as an alternative iron making route. Another 2.0 Mtpa, third generation FINEX® (3G) plant was recently installed at POSCO, Pohang Works and has been operating satisfactorily since its blow-in in January 2014. Based on the well-proven plant concept, new process features, the highly competitive production costs and environmental advantages, the FINEX® Process can be considered as a competitive alternative to the conventional blast furnace iron making route.

Aug 17, 2017

By E. Scheepers

Within a phosphorus producing submerged arc furnace it was found that the continuous fluctuation of the furnace between a flowrate-driven state (high throughput) and a thermodynamic-driven state (low throughput) caused both techniques to have similar overall, predictive abilities and resulted in a linear, ARX-type, adaptive prediction model as the model of choice. Secondly, this pre-diction model was developed, tested and then shown to have a reasonable, 8-hour-ahead predictive accuracy (R2, coefficient of determination) of 30% (±6%) on future Pslag values. This inherent relationship exists because, at the precise moment of a Pslag prediction, the furnace already contains the metallurgical memory (input variables to the linear model) needed to ensure that some predictive possibilities will always exists - all as a result of the long residence times in the furnace. Residence time, however, is not a directly adjustable variable but rather a fully dependent variable and a function of an array of interconnected and interactive variables. In fact, this applies to virtually all input variables, reemphasising the importance of innate metallurgical memory. Thirdly, predictive control possibilities were explored by simulating the set-points of two fully independent variables used by operators to control the process: the ratio of fixed carbon-to-P2O5 and the ratio of silica gravel-to-pellets. This linear, predictive control model showed only a slight improvement with an 8-hour-ahead predictive accuracy of 35% (±7%). This highlights how ineffective current adjustments are in optimally steering the process and how difficult even incremental improvements in feed-forward and predictive control can be. Finally, it is shown that fundamental design-, sampling- and process restrictions currently associated with the process will always limit the predictive and especially control accuracy or meaningfulness of any dynamic model. These restrictions include the size of the furnace resulting in long residence times, 8-hours sampling intervals, an extremely complex and interactive process and a 16% spatial analyses variation on the Pslag values ? the very value that the model is to predict. The point is made that, given the current status quo, even the perfect dynamic prediction model can not improve on an 8-hour-ahead prediction of 30% (±6%). This barrier can only be pierced with e.g. tidier and more frequent sampling regimes and other upfront capital investments, a decision that becomes a cost accounting exercise and that can only be taken by the management structure. An investment demanding ever-increasing attention is CFD software and it?s potential to shed more light on the complex interactions within the furnace.

Jan 1, 2014

By E. Scheepers

The process under investigation is the large-scale production of phosphorus. Gravity delivers the feed, consisting of pelletised apatite, coke and silica (in the form of gravel), to a submerged arc furnace through ten, evenly distributed feed chutes ensuring constant packed bed volume. Within this packed bed, solid-gas reactions are dominant in generating the gaseous product. These reactions, as well as the packed bed itself, were the main focus in the development of a fully three-dimensional CFD model in which fluid flow and energy distribution are represented as functions of chemical reactions, heating and melting of material and heat losses. The associated complex process interactions necessitated the creation of two process-specific, user-developed models that integrates accurate, thermodynamical data with computational fluid dynamics calculations, as well as reaction kinetics. The boundary conditions are provided by industrial measurements, and the key model parameters of reaction kinetics were obtained by laboratory experiments for different feed mixtures. Thirteen temperature probes installed inside the refractory lining of the furnace especially for this project allowed parameter fitting and validation to be guided within the constraints of real measurements. Simulation results reveal a thin, dome-shaped, reductive zone where conditions are optimum for maximum phosphorus recovery, as well as evidence of a thermal reserve zone similar to an ironmaking blast furnace located above this reduction zone. When compared to actual operating data, the CFD model can successfully predict the specific power consumption, the phosphorus in the slag and gaseous product flowrate under given operating conditions. This CFD model forms part of a larger project that aims to create a Dynamic-CFD hybrid control model.

Jan 1, 2014

By Ron Stewart, Richard Youmaran, Andy Adler

In the current context of heightened concerns with explosives security, there is significant interest in technological controls to improve security. It is important to be able to control what is fired, by whom, where and when. This paper describes research Orica has performed to investigate and test biometric systems to address the question of "by whom". The goal of this research is to incorporate the most suitable biometric system onto the 'blaster' unit of an electronic initiation system. This approach will ensure that only authorized personnel can initiate a blast involving electronic detonators. Requirements analysis: we initially explored many different biometric technologies to evaluate them against the requirements, including security, usability, ruggedness, size, form factor, privacy, and operational temperature range, This analysis identified chip based fingerprint sensors as the best candidate. Development of prototype units: in order to test the identified sensors, we modified standard, commercially-available, electronic blast initiation units ("blaster") to incorporate a fingerprint reader. Testing and evaluation: Biometric We conducted a biometric scenario evaluation in order to determine: 1) security level (measured by false accept rate (FAR)); 2) usability (measured by failure to enroll (FTE) and false reject rates (FRR)), and to 3) discover environment specific issues and challenges (such as temperature, humidity, dirt, or those related to the usage patterns of the user group). Tests were conducted at quarry sites in eastern Ontario, Canada. Results show rates of: FAR= 0%, FTE= 1.67%, FRR= 28.81%. Overall, these results suggest that this fingerprint biometric technology has a good level of usability in this application of electronic blast initiation control.

Jan 1, 2007

By C Bonini, A Markham, P Whittle, B Pearson

"Mine-derived sedimentation in rivers can have significant impacts on the processes and features of the receiving environment and impact on communities reliant on this environment. However, identifying and quantifying the contribution of mine-derived sediment to the receiving environment can be complex. This is particularly the case in remote environments and where little/no baseline assessments have been undertaken. One approach that can be used involves sediment fingerprinting, whereby a unique tracer is identified within the mine-derived sediment to discriminate between mine- and non-mine derived sediment sources downstream. The technique typically involves sampling of sediment at upstream, control and impact sites and sites within the mine deposit. Laboratory analyses are run on all the samples to determine whether the chemical signature (eg presence/concentration of specific metals) differs between each group of samples. In complex environments where the mine-derived signature may be difficult to detect from a basic review of the data, or where sampling constraints may limit the number of samples for analyses, statistical methods can be used to help identify sediment groups. This paper provides a mine case study to show how such an assessment can be undertaken despite the logistical challenges faced while working in remote environments.CITATION:Pearson, B, Markham, A, Bonini, C and Whittle, P, 2013. Fingerprinting and signatures - tracing mine impacts in complex aquatic systems, in Proceedings Water in Mining 2013, pp 287-292 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

Discussion Of the paper Of GEORGE K. BURGESS, J. J. CROWE, H. S. RAWDON, and R. G. WALTENBERG, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin NO. 93, September, 1914, pp. 2433 to 2437. ALBERT SAUVEUR, Cambridge, Mass.-The Bureau of Standards has once more rendered a public service. Manufacturers and consumers of steel rails alike should welcome the important results now laid before them by Dr. Burgess and his co-workers. Personally I welcome these results all the more that in the past, as some of the members may remember, I have never failed, when occasion arose, to call the attention of rail manufacturers to the importance of controlling the finishing temperature of their rails. The pioneer metallographic work conducted at the South Works of the Illinois Steel Co. in the early &apos;90s clearly brought out the close relations existing between the manufacture, properties, and finishing temperature of steel rails and I think I may say without fear of being contradicted that the results of this early investigation had considerable influence in drawing the attention of manufacturers to the importance of finishing temperature and of heat treatment in general. The results now before us should be, it seems to me, of great value to rail manufacturers in their efforts to produce a better and, above all, a safer rail. It seems to be demonstrated in this paper that there is no difficulty in installing in rail mills pyrometric outfits, making it possible to record, without interfering in the mill operations, the temperature of the rails as they leave the finishing rolls, or of the ingots as they are withdrawn from the soaking pits, or at any intermediate point in the process of manufacture. The inference necessarily follows that manufacturers should see to it that such pyrometric installations are made, in order that they may actually know, instead of guessing at, the temperature of their rails;, and, for obvious reasons, rail consumers should insist upon such installations. In the rolling of heavy sections especially should care be taken to lower their finishing temperature, seeing that the present tendency is to finish them at higher temperature, whereas, owing to the slower cooling of their central portions, which makes for coarseness of grain, they should, if anything, be finished at a lower temperature than lighter rails.

Jan 4, 1915

By George Burgess

NOTE BY THE EDITOR.-This resume of a Technologic Paper which is published in full by the U. S. Bureau of Standards, is brought before the membership of the Institute with the object of affording an opportunity for the open discussion of results of an investigation by the authors named above, of some phases of the manufacture of steel rails which are of great importance to manufacturer and consumer alike. This resume will be presented at the Pittsburg Meeting of the Institute. Discussion is invited, by either members or non-members of the Institute. The discussion may be sent in writing to the Editor, in advance of the meeting, or should preferably be presented in person at the meeting. To those who desire to discuss, copy of the full Technologic Paper (No. 38), as published by the Bureau of Stanaards, will be sent upon request addressed either to the Bureau of Standards, Washington, D. C., or to the Editor, American Institute of Mining Engineers, 29 West 39th Street, New York, N. Y. Summary of Researches and Conclusions The main objects of this investigation were to determine, from measurements taken at representative rail mills, the present American practice regarding the temperatures at which rails are rolled; to demonstrate the ease and accuracy with which such temperatures may be measured, without interfering in any way with the manufacture of the product; to find out what the "shrinkage clause" in rail specifications really means; and, finally, to determine some of the physical properties of rail steels, particularly those of interest in manufacture, some of which seem to be insufficiently known as yet. 1. Ingot Temperatures.-Measurements made in four mills show that ingots for rails are rolled at temperatures ranging from 1,075° to 1,150° C. (1,965° to 2,100° F.), and that, in a series of 20 to 40 ingots, the variation in temperature from one ingot to another is only 10° to 20° C. 2. Finishing Temperatures.-Rails are finished at temperatures ranging broadly from 880° to-1,050° C. (1,615 to 1,922° F.), but usually ranging within 50° C. of 935° C., and occasionally above 1,100° C.

Jan 9, 1914

By Joseph A. Sopko

The first documented procedures for designing frozen earth structures are over 50 years old, implemented long before the introduction of the Finite Element Method (FEM). Since that time, the development of three-dimensional models has made the traditional and often over-conservative methods relatively obsolete. This paper discusses a new approach that is largely dependent on the analysis of internal stresses with the frozen structure and comparison to frozen soil laboratory tests. A specific design process is discussed related to initial field investigation, laboratory testing, structural and thermal analysis, and performance monitoring. The design results are compared to case histories in the field that verify the procedure. BACKGROUND One of the first documented methods to designing frozen earth retaining structures was by Sangar (1968). Methodical refinements were published by (Harris 1995) and published by the International Symposium on Ground Freezing in 2002 (Andersland et al. 1991). The structural design or thickness of the frozen mass was based on the unconfined compressive strength of the frozen soils. Two simple equations for determining the thickness of a frozen shaft are shown in Fig. 1 and the first two equations below.

Jan 1, 2019

By Dimitrios C. Konstantakos

Cofferdam excavations have traditionally been designed with classical design methods that involve direct computations of active or apparent earth pressures. However in contrast to finite element methods, traditional analyses can not account for full soil-structure interaction. Because of their complexity, numerical analyses are performed almost exclusively by computers. Recent theoretical and computer advancements have made the use of the finite element method much more user-friendly and affordable. General information about the basics of the finite element method in geotechnical engineering and for cofferdam excavations is presented. While knowledge of all intricate theoretical and computational details is not needed, the designer should at a minimum be aware of the most important aspects of soil modeling. Most importantly, the designer must have sufficient experience to be able to judge the relative ?correctness? of vast numerical results produced by today?s software programs. Hence, the human factor is an irreplaceable component of finite element computations.

Jan 1, 2013

By K. F. Unrug

In the paper a numerical modeling method is used for evaluation of a roof support system, which is commonly used in the US coal industry. The effectiveness of mechanical roof bolting with or without, header boards and steel straps are compared. This analysis takes into account the response of a shaly roof to changing environmental conditions in mines related to the seasonal changes in temperature and humidity of the intake air. Discussed are principles of roof support in coal mines and based on them a critical evaluation of header boards interaction with bolts and roof itself is carried out. Header boards create a soft inclusion within a much more stiffer system comprising bolt-rock. As an alternative to header boards, steel straps are analysed and corresponding results are presented. It is demonstrated that application of steel strap is beneficial from the stand point of stress distribution and maintaining tension on roof bolts. The laboratory investigations and modeling work previously undertaken by the authors, clearly indicate the detrimental effect of header boards on effectiveness of roof bolting. There are significant practical implications of the research considering that header boards are commonly used in mines. This practice has been probably originated from the wooden support used by mining in "pre-bolting era?, and it has stayed with coal mining based on tradition more than principles of engineering design. It is demonstrated that header board$ are detrimental and actually contribute to development of roof problems.

Jan 1, 1989

By W. Jomaa, V. Songmene, O. Mechri, Laval Université, P. Bocher, J. Levesque

"A 2D finite element modelling (FEM), based on pure Lagrangian approach, is developed for studying the serrated chip formation during high speed machining (HSM) of 7075-T651 alloy. The solution was achieved using a commercial software package, ABAQUS/Explicit v6.13. The Johnson-Cooke (JC) constitutive equation is used to describe the work material behaviour. Moreover, the JC damage equation is implemented into the FEM to take into account for the shear localization during the serrated chip formation. Modified Coulomb friction model has been used to characterize the sliding/sticking effects on the tool-chip interface with the friction coefficient and shear flow stress determined by force calibration and machining data, respectively. The proposed FEM is validated using experimental data obtained in HSM of 7075-T651. The FEM was able to predict accurately serrated chip morphology. The intensity of chip segmentation was found to increase with cutting speed.INTRODUCTIONHigh speed machining (HSM) is one of the most used processes for manufacturing aircraft parts with aluminum alloys. For aluminum alloys, the use of HSM increases metal removal rate and reduces the formation of built up edges and burrs. However, it was found that serrated (also named segmented or sawtooth chip) and discontinuous chips can be produced during HSM of some high strength aluminum alloys, such as 7075-T6 alloy (Rao & Shin, 2001). Many parameters were found to affect the segmented/discontinuous chip formation during the machining of aluminum alloys.There are two cases in which the serrated chip can forms: the first is when machining hardened materials (Morehead, Huang, & Luo, 2007), and the second, when machining ductile materials with a cutting speed higher than a critical value (Barry & Byrne, 2002). Different theories and models were developed in order to explain the formation mechanism of such kind of chips. According to Astakhov (2006), the segmented chip formation is attributed to variations in stress and plastic deformation states, and resulting temperatures on the cutting zone. Liyao et al. (2013) stated that the segmented chip formation was mainly attributable to adiabatic shear instability/catastrophic strain localization. Others (Vyas & Shaw, 1999) suggest that the fracture/crack propagation mechanism is at the root of chip generation."

Jan 1, 2016

By B. MohammadSadeghi, S. Bakhshivash, M. Haghshenas, F. Rahimi

"Constrained groove pressing (CGP), as a severe plastic deformation (SPD) technique, is one of the applicable methods for sheet metal forming capable of producing ultra-fine grained materials (UFGMs). In CGP, processing and die design parameters can significantly affect the deformation response of sheet metal specimen. Having said this, in the present research the effects of die design variables and processing parameters (i.e. shear angle and friction) on the deformation behaviour of an Al-Mg-Si Alloy are studied thoroughly. Finite element analysis (FEA), was used to evaluate the effectiveness of mentioned parameters on the deformation homogeneity, strain distribution and pressing load variations. Also, mechanical properties of the deformed sample in term of micro-hardness was analyzed. It is observed that with increasing the shear angle, effective stress, strain and pressing load are enhanced. Moreover, by increasing the coefficient of friction, pressing load enhances. The color coded micro-hardness measurement showed a good agreement with the strain distribution obtained from FEA (higher hardness for the zones associated with higher shear plastic strain values).INTRODUCTIONWork hardening results in enhanced mechanical properties upon cycles of deformation (Hosford & Caddell, 2007). However, the formability of the processed products are affected by work hardening reducing the possibility of processing in subsequent deformation cycles. Therefore, many industrial processes cannot be performed on sheet metals to produce products with desired mechanical and physical properties (Valiev, Islamgaliev, & Alexandrov, 2000). Severe plastic deformation (SPD) is an effective grain refining technique which can impose large plastic strains through cold working on a metallic specimen (Bisadi, Rastgou, Payganeh, Zeynali, & Ghahremani, 2010). SPD techniques are mainly categorized into three types; sheet, bulk and tube forming. Among SPD sheet forming methods, Constrained Groove Pressing (CGP) (Shin, Park, Kim, & Park, 2002), Accumulative Roll Bonding (ARB) (Saito, Tsuji, Utsunomiya, Sakai, & Hong, 1998) and Repetitive Corrugation and Straightening (RCS) (Zhu, Lowe, Jiang, & Huang, 2001) possess potential applications in manufacturing industries."

Jan 1, 2016

By W. G. Pariseau

Conventional barrier pillars in underground coal mines are intended to protect mains and sub-main entries for relatively long periods of time. Inter-panel barrier pillars that may be used in especially deep coal mines, say, below 800 m (2,400 ft), are intended to protect longwall panel faces and adjacent panel entries for the life of nearby panels. Barrier pillar failures have serious consequences, especially when failure is sudden and catastrophic. Design of barrier pillars is thus of considerable importance to safety and efficiency of operations. Locally, failure occurs at the limit to elasticity when stress tends to exceed strength. Strength of rock is stress dependent, so an analysis of stress is central to rational design of barrier pillars. There are several approaches to stress analysis for coal mine pillar design that range from the simplified but popular tributary area method including variations that use empirical definitions of the tributary area (volume) to more sophisticated numerical methods such as the boundary element method and the finite element method. Despite ease of use, empirical methods are limited and always suspect when applied to conditions beyond their scope of definition, while boundary element methods do not generally include pillars in the solution domain. The finite element method is not so restricted and thus is a natural choice for conventional and inter-panel barrier pillar safety analyses. Caving of roof strata certainly affects the distribution of stress about longwall faces and nearby barrier pillars. Conventional wisdom that considers roof strata to respond as cantilever beams indicates the longer the span the greater are loads on longwall faces and face supports. Failure of roof beams, caving, shortens spans and relieves face and support loads. The same view is applicable to barrier pillars in that long roof spans outside of barrier pillars leads to higher pillar loads than short spans. Hence, caving should be beneficial to barrier pillar safety. However, the benefit may be small depending on the extent of caving and only in the form of a slight reduction in overburden weight transmitted to the barrier pillar, especially in case of inter-panel barrier pillars. FINITE ELEMENT MODEL Finite element models for stress analysis in rock mechanics are formulated in consideration of physical laws, kinematics, and material laws. These models meet the essential requirements for equilibrium of stress, satisfy strain displacements relations, and in a general sense, relate stress to strain through material laws, often referred to as constitutive relations. The last may be complex and replete with nonlinearities. A de facto engineering material law is the elastic model in the form of Hooke?s law for linear, homogeneous materials that may be anisotropic. A limit to elasticity is imposed by strength in the form of a failure criterion or yield function that accommodates triaxial stress states. Examples used in rock mechanics are the well-known Mohr-Coulomb (MC)criterion, the popular Hoek-Brown (HB) criterion, and the Drucker-Prager (DP) criterion. The first is linear in stress, while the second is nonlinear. Both do not include any effect of the intermediate principal stress. The last is also linear in stress but includes the intermediate principal stress. All show an increase in the major principal stress at failure with confining pressure. In the UT2/3 finite element programs, the failure criterion Y is a nonlinear, anisotropic form and is also the plastic potential [1]: [YJI=+ 11NYJI=+- (1) ] where N is an exponent, usually 2, and J2 and I1 are nonlinear anisotropic forms of the second invariant of deviatoric stress and the first invariant of principal stress. The form (1) reduces to DP when N=1and isotropy prevails. When Y = 1, the limit to elasticity is reached and plastic deformation is possible. The material constants that enter (1) are all computed from unconfined compressive, tensile, and, in case of anisotropy, shear strengths. These latter strengths may be estimated from conventional laboratory test data. Of course, joints in field-scale rock masses induce different values. How different is often a matter of conjecture. For comparative studies, laboratory rock properties seem adequate. Inelastic, that is, plastic behavior occurs with strain beyond the elastic limit. Strain hardening, ideal plasticity, and strain softening are possibilities. Ideally brittle behavior with complete loss of strength is an extreme form of strain softening [2]. Caving may also be considered as strain softening with a less drastic reduction of material properties. As intact roof strata fail, fall, and form a rubble pile below, a new material is formed with greatly reduced elastic moduli and strengths, say, 1/100th of the original intact moduli and strengths. From another viewpoint, caving is simply a natural cut and fill process. Input for stress analysis by the finite element method includes: 1. Preexcavation stress state 2. Geology (stratigraphic column) 3. Structure (major faults, joint sets) 4. Elastic moduli 5. Strengths, and specific gravities of each rock type 6. Excavation sequence Output from an analysis includes distributions of: 1. Stress 2. Strain 3. Displacement 4. Local factor of safety (element fs) The last is defined as the ratio of strength to stress and in view of the failure criterion (1), is the ratio [fsJstrengthJstress=] where the numerator is the maximum possible value and the denominator is the actual value of the square root of the second invariant of deviatoric stress. This invariant is a measure of shear stress intensity but also reduces to uniaxial tensile and compressive strengths as the case may be. An fs greater than 1 indicates an elastic state of element stress; a value of 1 indicates the limit to

Jan 1, 2009