Search Documents

By M. Maier

Geographic Information Systems (GIS) has evolved into a powerful tool for analyzing spatial and attribute data in many industries including mining. Modern field data collection techniques add another dimension to the use of data in the field and enhance the utilization of GIS for mining applications. This discussion will review how field data is collected and how office data and maps can be taken into the field to be analyzed and verified using pen-based computers and differentially corrected GPS.

Jan 1, 2001

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

8. Field Demonstration of the Remote Mine Sealing System in a Coal Mine 8. 1 Selection of Field Test Site Eastern Associated Coal Corporation (EACC) offered its Federal No. 1 coal mine in Grant Town, West Virginia as the site for field testing of the remote sealing system. The choice of Federal No. 1 mine was particularly appropriate as the first attempt at fire control by remote sealing was done in this mine in 1963. EACC provided the men and equipment required for much of the initial preparation. Considerable assistance, advice, and background on coal mining technology was given by Mr. William Laird, Vice President for Research and Development, EACC, and by Mr. Lawrence Jackson, Resident Engineer at the Federal No. 1 mine. District 3 USBM office, the West Virginia Bureau of Mines, the Technical Support Group of the USBM, and Local 4047 of the United Mine Workers of America also cooperated. 8.2 Preparation of Field Test Site 8.2. 1 Underground Site Preparation The underground site chosen for the field testing was in a non-working portion of the mine within a few hundred feet of the main haulage road, as shown in Figure 80. Known as "Seven Switch, " this area was a 20 minute walk or 5 minute "jeep" trip from the man-trip shaft. Ten years having passed since this area was actively worked, considerable effort was required for gob clearing, roof bolting, rock dusting, and rejuvenating the track from the haulage road to the test area. Three primary borehole locations were chosen for the test program. Borehole No. 1 was in a straight passageway

Jan 1, 1973

By Y A. Stepanyants, J Crawford

A practical field method for determining the maximum value of the intrinsic oxidation rate, Smax , of sulfidic materials in waste rock dumps is proposed. Knowledge of the intrinsic oxidation rate of sulfidic materials distributed in a dump is necessary for predictive modelling of oxidation and pollutant generation over time. The suggested method uses the fact that drilling waste rock dumps to install probes for monitoring temperature and oxygen concentration causes large volumes of air to be injected into a dump by the drill rig. By measuring the rate of decrease of oxygen concentration along the length of a borehole immediately after installation, it is proposed that Smax can be calculated at different depths. The aims of this work were: to derive a simple, practical formula for the estimation of Smax from the oxygen concentrations measured over time, based on some simplifying assumptions; to use a two-dimensional numerical model that incorporates all the necessary physical processes to model the behaviour of an aerated dump over time for a reasonable range of dump and material parameters; and to compare the results of the two approaches to assess the validity of the simple formula as a method for estimating Smax. It has been found that the technique can provide reliable estimates of Smax when the value is of the order of 10-7 kg(O2) m-3 s-1 or greater. At the lower end of the range however the radius of the zone aerated during drilling becomes an important parameter and further work has been recommended to investigate this aspect of the method.

Jan 1, 2003

By McNay L. M

Two field studies to monitor fill pres sures and vein-wall deformation were conducted in mines of the Coeur d'Alene mining district in Idaho. Both operations employed cut-and-fill mining techniques in nearly vertical veins aver- aging 10 feet in width, and backfilled with classified mill tailings. Hydraulic pressure cells were used to measure transverse, longitudinal, and vertical pressures within the backfilled stopes. Rock bolts extending into the manways and mechanical closure devices were used to monitor vein-wall convergence. Continuous recorders were used with selected pressure cells to prolong the life of the installation. Transverse pressures in excess of 600 psi and stope wall closure up to 22 inches were re- corded. Closure rates were higher at midheight of the stope than they were near either sill, indicating that the vein walls react similarly to a beam supported on each end.

Jan 1, 1973

By H. C. Verakis, M. L. Harris, M. J. Sapko, K. L. Cashdollar

In underground mines, coal dust explosions are prevented by the addition of rock dust sufficient to render the coal dust inert. The National Institute for Occupational Safety and Health (NIOSH) has developed a hand-held instrument that uses optical reflectance to measure the explosibility of a rock dust and coal dust mixture. This instrument is called the Coal Dust Explosibility Meter (CDEM). In this study, NIOSH personnel accompanied Mine Safety and Health Administration (MSHA) inspectors on their routine band surveys in five and three underground coal mines in MSHA District 2 (PA) and District 11 (AL), respectively. While underground, NIOSH personnel and MSHA inspectors used the CDEM to assess the explosibilities of the dust samples. The values of percent incombustible content (% IC) determined by the CDEM agreed well with those obtained later by low temperature ashing (LTA) in both MSHA and NIOSH laboratories. Further, the meter identified some samples as potentially explosible that LTA analysis had found to possess sufficient rock dust for inerting. The CDEM provides more information on the hazards in the mine. Rapid identification of areas with explosible dust mixtures using the CDEM allows for immediate intervention rather than a wait of several weeks for laboratory analysis.

By M. L. Harris

In underground mines, coal dust explosions are prevented by the addition of rock dust sufficient to render the coal dust inert. The National Institute for Occupational Safety and Health (NIOSH) developed a hand-held instrument that uses optical reflectance to measure the explosibility of a rock dust and coal dust mixture. This instrument is called the Coal Dust Explosibility Meter (CDEM). In this study, NIOSH personnel accompanied Mine Safety and Health Administration (MSHA) inspectors on their routine band surveys in five underground coal mines in MSHA District 2 (Pennsylvania) and three underground coal mines in MSHA District 11 (Alabama). While underground, NIOSH personnel and MSHA inspectors used the CDEM to assess the explosibilities of the dust samples. The values of percent incombustible content (percent IC) determined by the CDEM agreed well with those obtained later by low-temperature ashing (LTA) in both MSHA and NIOSH laboratories. Further, the meter identified some samples as potentially explosible that LTA analysis had found to possess sufficient rock dust for inerting. The CDEM provides more information on the hazards in the mine. Rapid identification of areas with explosible dust mixtures using the CDEM allows for immediate intervention rather than a wait of several weeks for laboratory analysis.

Jan 1, 2008

By M. L. Harris

In underground mines, coal dust explosions are prevented by the addition of rock dust sufficient to render the coal dust inert. The National Institute for Occupational Safety and Health (NIOSH) has developed a hand-held instrument that uses optical reflectance to measure the explosibility of a rock dust and coal dust mixture. This instrument is called the Coal Dust Explosibility Meter (CDEM). In this study, NIOSH personnel accompanied Mine Safety and Health Administration (MSHA) inspectors on their routine band surveys in five and three underground coal mines in MSHA District 2 (PA) and District 11 (AL), respectively. While underground, NIOSH personnel and MSHA inspectors used the CDEM to assess the explosibilities of the dust samples. The values of percent incombustible content (% IC) determined by the CDEM agreed well with those obtained later by low temperature ashing (LTA) in both MSHA and NIOSH laboratories. Further, the meter identified some samples as potentially explosible that LTA analysis had found to possess sufficient rock dust for inerting. The CDEM provides more information on the hazards in the mine. Rapid identification of areas with explosible dust mixtures using the CDEM allows for immediate intervention rather than a wait of several weeks for laboratory analysis.

Jan 1, 2008

By Christopher Mark

The Bureau of Mines is conducting research to assess the effectiveness of different chain pillar designs in maintaining gate entry stability. The study described in this paper was performed in a 1200 ft long, experimental headgate section which contained three pillar designs: - a three-entry, yield-abutment pillar' system, - a four-entry, yield-yield-abutment pillar system, and - a five-entry, all-yield pillar system. As the longwall mined by the experimental section, Bureau engineers monitored entry convergence, roof sag, and changes in roof quality. The results of the study indicate that the all-yield system performed at least as well as, and probably better than, the two abutment pillar systems.

Jan 1, 1988

By Peter Altounyan

The rate of decay of the energy from a hammer blow to a coal mine roof is related to the size and nature of the contacts between the rock being struck and its surroundings The use of this principle as a basis for testing roof condition in South African coal mines has been investigated under a SIMRAC funded project, with the objective of reducing the number of roof falls. ( I ) A prototype instrument having a simple numeric display related to the energy decay rate (the Acoustic Energy Meter) was constructed and used to carry out surveys at mines covering the range of coal mine roof geology and condition. The equipment was simple to use and provided excellent discrimination between visually intact roof and less stable conditions, once the normal/abnormal threshold had been established for a given site. Areas of potential roof failure were identified close to roof slips and igneous dykes, and confirmed in areas of visible deterioration. Directional stress effects on roof condition were also identified at some sites, with consistent differences in readings obtained depending on the direction of drivage. Repeat surveys also indicated areas where roof conditions were deteriorating with time. Based on the success of the prototype, a hand held version of the instrument. has been developed to a specification from Anglo Coal. This incorporates a simple 'traffic light' green / amber/ red display, making the device suitable for routine use by mine operatives This version is now undergoing trials at an Anglo Coal mine. It is concluded that the Acoustic Energy Meter shows great potential as a test instrument providing output which relates to the stability of the immediate roof.

Jan 1, 2000

By Michael Magerstädt

Material loss by abrasion of contact surfaces of pipes, chutes, pumps, and other equipment in contact with ore is one of the main reasons for downtime of mining operations. Abrasion protection materials in use range from expensive tungsten carbide overlay to hardened steels, ceramics, as well as polymers, particularly polyurethanes (PUR). This paper describes abrasion protection products made from High Performance Polyurethane Elastomers. An interior pipe coating was developed that exhibited outstanding abrasion resistance and an extremely high adhesion to steel. Years of field testing in oil sands tailings as well as applications in slurry lines (e.g., phosphate slurries) have proven the performance of this material. A proprietary field joining process was developed and successfully applied in the field. This joining process requires only one field weld per joint very similar to the joining of uncoated pipe. No internal re-coating is necessary adding savings during pipe laying to the significant savings of reduced down time. Using the building-kit chemistry of polyurethane synthesis, similar high performance elastomers were used to extend the life time of ball mills. An intelligent system was developed in which wear parts contain sensors reporting the actual wear thereby optimizing maintenance interval leading to significant cost savings for the operator. Test data as well as field experience with High Performance PUR Elastomers for abrasion protection in mining are presented.

Aug 1, 2013

By J. P. Kennedy

Process data managers or historians are recognized as essential for reengineering projects in industrial plants. With increasing automatic data collection, the knowledge of how to use these data profitably grows as well. This paper is a summary of the data historian and its components plus examples of benefits including environmental reporting, performance monitoring, and exception reporting to management.

Jan 1, 1994

By Y. Guglielmi, C. Gout, P. Henry, P. Dick

The key questions about fault reactivation in shales concern the potential enhanced fluid displacement through a previously low-permeability aseismic shale formation. Here we selected a critically-stressed fault cross-cutting the underground research facility of Tournemire (France) which is located in Toarcian shales. Several inclined boreholes were drilled across the 8.5 m thick fault zone characterized by a fractured damage zone (FDZ) and a central 2.4 m thick complex core (FC) made of multiple shear bands with gouge intercalated with highly fractured lenses. The fault was pressurized using a straddle packer system defining a 2.4m long injection chamber normal to the fault surface. Three fault zone intervals were tested, two in the fault damage zone and one in the fault core. A three-dimensional displacement sensor set in the chamber allowed continuous synchronous coupled monitoring of fault movements, injection pressure and flow rate. An anticlockwise 0.22-to-0.05 mm fault slip was captured associated with a 10-to-100 hydraulic aperture increase of the fault. Preliminary analyses of the experiments show that leakage in the fault zone is controlled by strength and stress magnitude contrasts between the fault core and the fault damage zone. Fault damage zone discontinuities display a much higher peak static friction angle than the fault core shear zones, respectively of 34 and 22° that could be related to complex interactions between healing and sealing processes. Fault core leakage is much more dependent on strain than on effective stress variations. Discontinuous, pulse-like leakage, develops following complex failure processes that may simultaneously take place in the gouge zones and along the large pre-existing discontinuities. Such results may be of importance in evaluating fault seal integrity in oil and gas exploration, production or CO2 storage or underground excavations monitoring.

Jan 1, 2015

By Todd Minoski, Matthew McElhinney, Mark Morris, Mark Mazzella, Joseph Bright, Morgan Sears, Craig Compton

To promote the safety and health of U.S. mineworkers, researchers with the National Institute for Occupational Safety and Health (NIOSH) are currently involved in gathering additional field data from the nation’s underground coal mines. The purpose of this field study was to monitor ground movement and changes in pressure during mining where conditions include a thick parting in the coal seam. To accomplish this, three arrays of field instrumentation were installed in the wraparound bleeder of a room-and-pillar panel at the Maple Eagle mine located in southern West Virginia. Borehole pressure cells (BPCs) were used to monitor the change in pressure in pillars located adjacent to the gob. Roof extensometers were installed to measure roof sag at various horizons in the immediate roof, while rib extensometers were installed to measure displacement of the in-seam parting as mining progressed. Additionally, visual observations and manual measurements were taken during subsequent site visits. The repeatability of results, important from a scientific perspective, was accomplished by successfully obtaining field measurements from two nearly identical instrumentation sites. The data collected indicated that the front abutment extent at the edge of the panel was approximately 200 ft, corresponding to a distance of 9– 10 times the square root of the depth. Yielding of the slabbed pillar began when the pillar line was approximately 290 ft outby the instrumentation sites. This was followed by load shedding onto the abutments and the measurement of small amounts of roof sag in the No. 1 entry. Instrumentation data, as presented in this paper, can be used to better understand stress redistribution, pillar performance, and roof/rib displacements. Additionally, this data is suitable for assisting in the calibration of numerical models. Insight gained from applying these models can be used to make better engineering-based judgments for conditions that could potentially be encountered in the future.

Jul 1, 2023

By D. G. F. Hedley, D. F. Coates, K. Barron

INTRODUCTION Preceding papers presented in this symposium have considered the influence of various parameters, such as geologic structure, groundwater, etc., on the stability of rock slopes and have given some analyses and guide lines for slope design. To carry out such analyses it is necessary to put numbers to these parameters; where possible, this is best done on the basis of in- situ observation and measurement. Since none of the design analyses can be considered exact and since conditions vary during excavation, it is also desirable to monitor the behaviour of the slopes as the excavation proceeds. In this manner a feedback of information on the actual excavation conditions can allow a continuous reassessment of the design parameters to be made and can give early warning of incipient failures. The purpose of instrumenting rock slopes is thus to provide information which fits into one of two categories: (a) To give basic data to assist on-site assessment and design of the rock excavation. (b) To provide data for the control and assessment of safety during excavation. The purpose of this paper is to review briefly some of the instruments and measuring techniques available for gathering this data and to indicate where such data may prove useful. This is not a comprehensive review of all available instrumentation but, rather, is a survey of some of the instruments and techniques with which the authors have had some experience and which have proven useful. STRUCTURAL ASSESSMENT Whilst most structural assessment of a site is done on the basis of geologic mapping and core examination, there exists some instrumentation which can, in particular circumstances, assist in this assessment. Seismic instruments can be used to determine the geometry of formations and to give an indication of the relative competency of rocks. These instruments operate using seismic reflection or refraction techniques and, although mainly confined to shallow sub-surface exploration, can be useful in distinguishing between soil/ bedrock contacts and, in some cases, the extent of weathered surface rock.

Jan 1, 1971

By M. Yekich, W. R. Reed, G. Ross, M. Shahan

"Canopy air curtains on roof bolting machines have been proven to protect miners from respirable dust, preventing their overexposure to dust. Another desired application for canopy air curtains is in the compartments of shuttle cars. The challenges faced in developing the design of canopy air curtains for shuttle cars include mine ventilation rates in tandem with the shuttle car tram speeds. The resulting cab airspeeds may exceed 182 m/min (600 fpm), as found in the present study conducted in a central Appalachian underground coal mine by U.S. National Institute for Occupational Safety and Health (NIOSH) researchers. Prior research and laboratory testing had indicated that successfully protecting a miner in high air velocities is difficult, because the clean air from the canopy air curtain is unable to penetrate through the high-velocity mine air. In this study, the dust concentrations to which a shuttle car operator was exposed were measured, and air velocities experienced by the operator were measured as well using a recording vane anemometer. The results indicate that the highest exposure to respirable dust, 2.22 mg/m3, occurred when the shuttle car was loading at the continuous miner, where the average airspeed was 48 m/min (157 fpm). While tramming, the operator was exposed to 0.77 mg/m3 of respirable dust with an average airspeed of 62 m/min (203 fpm). This study indicates that a canopy air curtain system can be designed to greatly reduce an operator’s exposure to respirable dust by providing clean air to the operator, as the majority of the operator’s dust exposure occurs in air velocities slower than 61 m/min (200 fpm). IntroductionThe U.S. National Institute for Occupational Safety and Health (NIOSH) issued contract #200-2015-63485 to develop a canopy air curtain for coal mine shuttle cars with Marshall University and J.H. Fletcher & Co. (Salem, Begley and Ross, 2016). The proposed design maintains a design similar to that of a roof bolter canopy air curtain by providing filtered air through a blower over the operator. The plenum, which will provide uniform airflow over the operator, is anticipated to be built into the shuttle car canopy. One of the main interferences with a canopy air curtain is ventilation airflow perpendicular to the plenum airflow (Engel, Johnson and Raether, 1987). This ventilation airflow can shear the downward flow from the plenum, and this shear can reduce the effectiveness of the canopy air curtain by either disrupting the downward flow or allowing contaminated mine air into the canopy air curtain zone of protection."

Jan 11, 2018

By Clive Ellis, Brian Davies, Steven E. Mischler, Jon C. Volkwein

A primary means to reduce environmental levels of diesel particulate matter (DPM) exposure to miners is to reduce the amount of DPM emission from the engine. A quick and economic method to estimate engine particulate emission levels has been developed. The method relies on the measurement of pressure increase across a ?lter element that is brie?y used to collect a DPM sample directly from the engine exhaust. The method has been re?ned with the inclusion of an annular aqueous denuder to the tube which permits dry ?lter samples to be obtained without addition of dilution air. Tailpipe ?lter samples may then be directly collected in hot and water-supersaturated exhaust gas ?ows from water bath-cooled coal mine engines without the need for dilution air. A primary means to reduce environmental levels of diesel particulate matter (DPM) exposure to miners is to reduce the amount of DPM emission from the engine. A quick and economic method to estimate engine particulate emission levels has been developed. The method relies on the measurement of pressure increase across a ?lter element that is brie?y used to collect a DPM sample directly from the engine exhaust. The method has been re?ned with the inclu­sion of an annular aqueous denuder to the tube which permits dry ?lter samples to be obtained without addition of dilution air. Tailpipe ?lter samples may then be directly collected in hot and water-supersaturated exhaust gas ?ows from water bath-cooled coal mine engines without the need for dilution air.

By R Van Laeren, G Langerak, S Fityus, K Koosmen

Co-disposal of partly-dewatered mixed-plant rejects (MPR) from coal processing into spoil dumps is gaining favour amongst Australian coalmine operators in preference to conventional tailings disposal methods which require a tailings dam. Owing to their often low permeabilities and high degrees of saturation, MPR materials may be prone to the development of excess pore pressures when covered by spoil during routine dump advancement. The likelihood of dump failure will increase if these pore pressure regimes and the associated delay of shear strength development are not accounted for during waste dump design. To date however, little is known about these pore pressure regimes due to the complexities associated with their in situ measurement.This paper describes the in situ measurement of pore pressures in a cell of MPR placed within a coalmine spoil dump. Four vibrating wire piezometers (VWPs) were placed within a cell that was then filled with MPR and allowed to consolidate under self-weight before advancing an adjacent tiphead across the cell. The VWPs recorded the transient pore pressures during MPR placement and dump construction, and their interpretations are described within the context of laboratory measured parameters. Following analysis of the measured pore pressures, their implications on shear strength and dump design are also discussed.CITATION:Koosmen, K, Langerak, G, Simmons, J, Fityus, S and Van Laeren, R, 2015. Field measurement of transient pore pressures within co-disposed processing rejects placed in a spoil dump, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 63–72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By Christopher Mark

Current longwall pillar design methods are based on many assumptions about pillar and entry response to longwall abutment loads. Knowledge of the magnitude and time-of-arrival of abutment loads is essential for Improving design procedures. The abutment loads are in turn related to the development of yield zones and horizontal confining stresses in pillars. Entry stability, which is the goal of any longwall pillar design, is affected by in situ stresses as well as the interaction between the roof, pillars, and floor. The paper describes a study performed in a longwall panel at a West Virginia coal mine. The behavior of two headgate pillars and the adjacent entries was- monitored as the longwall face approached and moved past. The results provided a detailed picture of the response of long- wall pillars and entries to abutment loadings.

Jan 1, 1986

By Peter Faust, Peter Hubbard, Kenichi Soga

The European Federation of Foundation Contractors (EFFC) and The Deep Foundations Institute (DFI) have set up a task group to compile a Guide for Working Platforms. The first edition of this Guide has been published in January 2020. The aim of the Guide is to provide reliable methods for design, testing and verification of working platforms for construction equipment, especially in the deep foundation industry where track loads can be excessive due to the nature of its operations. The Guide has identified areas where knowledge is limited. Actual track pressure and its distribution along the length of the tracks is still not well researched. Current recommendation provided in EN 16228-1 are believed to be overly simplified and may lead to conservative requirements for working platform thickness. This paper presents results of a series of field tests where the actual track pressure of a large drilling rig during operation was measured in real time together with the deformation of the working platform. Embedded, distributed fiber optic sensing (DFOS) at different depths throughout the platform allowed for a three-dimensional evaluation of the platform deformation throughout the entire operation. Results will help to develop more reliable recommendations for future safety requirements of working platforms for deep foundation equipment.

May 1, 2022

By Daniel W. H. Su

Current longwall pillar design relies heavily upon past experience and many assumptions about pillar and entry response to longwall abutment pressures. Caving characteristics of the immediate and main roof strata are known to play an important role in the overall pressure redistribution, which determines the maximum abutment pressure, abutment pressure at the T-junction, and the width of influence zone. This paper presents the results of an extensive geomechanical study in a longwall panel at a West Virginia coal mine. The response of eight headgate pillars and the adjacent entries was monitored as the longwall face approached and passed by the instrumented locations. Overburden response to longwall mining was also monitored, and height of the highly fractured zone above the gob was determined by postmining drilling. Good agreement was observed between the measured stress changes and those computed using the known height of the highly fractured zone. The results provide a detailed picture of the response of overburden strata and chain pillars to longwall mining.

Jan 1, 1987