Search Documents

By F. C. Langenberg

IT is the purpose of this paper to present a limited amount of experimental data obtained on the Charpy impact machine. Several concrete examples will be given showing the relation existing between the results obtained upon the Charpy impact machine and the behavior of the parts tested when in service. Although it is pointed out by G. Charpy and A. Cornu-Thenard1 that it is first necessary to determine a satisfactory working process before studying the correlation between the results of these tests and the behavior of the parts tested in service, this ideal course cannot be strictly adhered to. If a certain part repeatedly fails in service and the available tests give no indication of its cause, advantage must be taken of any possible means that will solve the problem; therefore, even though the reliability of the results obtained by the Charpy impact machine have been questioned by many, it was necessary to use this instrument without giving careful consideration to its possible sources of error. It would seem that the conclusions arrived at by Charpy and Cornu-Thénard justify the assumption that the precision obtained by this machine is comparable to that obtained by, the other more common forms of testing. The second general conclusion arrived at by them, namely, that the impact test upon notching does not offer any direct correlation to the ordinary tests, is also borne out by many hundred determinations made in the laboratories at Watertown Arsenal. This statement, however, should be qualified as follows: Other ordinary tests include the static tensile test from bars taken in a longitudinal .direction and the Brinell hardness. The author agrees that no law is yet known for the computation of the energy absorbed in the rupture of bars of the same material but of different dimensions. Although Charpy and Cornu-Thénard do not refer in their valuable article to the use of the Charpy machine in industrial practice, it should be stated that this instrument has been in constant use in the laboratory at Watertown Arsenal for several

Jan 8, 1919

By R. J. Sweigard

Stabilization of slopes on abandoned mine land (AML) invariably involves some channelization to control surface drainage. Typically, these channels are lined with riprap or gabions, depending on gradient and expected flow rate. The conventional treatments pose a problem since they require frequent maintenance and replacement at times. Soil bioengineering presents an alternative to the conventional measures. In soil bioengineering, living woody plant material forms the main structural component in systems designed to prevent shallow mass slope failures, surface erosion, and channel bank erosion. An experimental application of soil bioengineering techniques was designed and implemented at an AML site in eastern Kentucky. The design consisted of live fascines and live stakes using willow branches installed with coir geotextile. Channel gradient, length, and cross-section were considered in the design.

Jan 1, 1998

By Y. Zedan

In this study, the statistical design of experiments (DOE) was applied to study and regulate the properties of near-eutectic Al-11%Si alloys. Develop regression equations for such response variables as hardness, yield stress, ultimate tensile stress, percent elongation, total cutting force, cutting power, and tool life together with other factors which, include the percentage composition of the alloying elements, and the requisite modification (Sr) level. These equations may be analyzed quantitatively to acquire an understating of the effects which the main variables and their interactions may have on the mechanical behaviour and the machinability of the alloy under investigation. The results reveal that increasing the levels of Cu and Fe content results in an increase in hardness, yield stress, and ultimate tensile strength in both modified and non-modified alloys. On the other hand, both Cu and Fe appear to affect the percentage elongation adversely, whereas the Sr-level has a positive effect on this parameter. It was found that Sr-levels have the most significant effect on the cutting forces and cutting power followed by the content in Fe and Cu. The results also reveal that the interaction coefficients of these variables have a significant effect on tool life compared to the main independent variables. This fact may be attributed to the formation of complex insoluble phases between Cu, Fe, Si, and Al as investigated using Scanning Electron Microscopy (SEM) attached to an EDX analysis system. The accuracy of the regression equations in predicting the expected properties has been verified by carrying out random experiments in the range of variation of these variables.

Jan 1, 2011

By M. I. Brasileiro

The use of experimental design to the study of mixtures has found a wide range of applications, even in laboratory scale or in industrial development works. The aim of this work was to maximize granite sawing waste content in ceramic tiles using experimental design. Based on the raw materials, specific formulations were developed using the experimental design. The raw materials were mixed and sample bodies were produced using uniaxial pressing. The sample bodies were fired and characterized in terms of water absorption, mechanical strength and X-ray diffraction. Regression models were adjusted relating the water absorption and mechanical strength with the amount of raw materials. The results showed that the methodology of experimental design maximize the content of wastes incorporated in ceramic tiles formulations. Formulations containing up to 40% of waste can be used for the production of ceramic tiles.

Jan 1, 2009

By Md. Amanullah

A novel triple action load cell assembly (LCA) was developed to determine three index parameters reflecting compressive, tensile and shear characteristics of mudcakes. The results indicate that the tensile, compressive and torsional behaviour of mudcakes are strongly influenced by the physics and chemistry of the mud additives. Eine neuartige dreifach wirkende Druckkammer zur Bestimmung der drei Indexparameter Druck, Zug, und Scherung von Spülungskuchen wurde entwickelt. Die Ergebnisse weisen auf einen starken Einfluss der physikalischen und chemischen Spülungszusätze auf Druck, Zug, Scherung hin. Un assemblage d'une nouvelle cellule a triple action (LCA) a été développée pour déterminer trois paramètres caractérisant la compression, la contrainte en traction et la résistance á la fracture des cakes. Les résultats indiquent que les comportements tensile, compressif et de torsion des argiles sont fortement influencés par la chimie et la physique des additifs des boues.

Jan 1, 2003

By C. C. Clark, S. J. Jung

Determining the correct combination of mix components and water for high-density paste backfills that have the transport and deposition properties necessary for a mining operation is a difficult task. Rheologic properties cannot be determined without conducting full-scale pumping tests, and data from existing tests tire very limited. This paper presents the findings of investigations undertaken to determine if paste-backfill rheology can be determined using existing techniques and to determine which mix and system variables have the greatest influence on transport-pressure loss. Data from laboratory-scale pumping tests were used to produce a rheologic model of flow behavior for comparison, and a statistical analysis was conducted to determine the most significant factors affecting transport-pressure loss.

Jan 1, 1996

By S. J. Jung

Determining the correct combination of mix components and water for high-density paste backfills with the transport and deposition properties necessary in a mining operation is a difficult task. Rheologic properties cannot be determined without conducting full-scale pumping tests, and data from existing tests are very limited. The following presents the findings of investigations undertaken to determine if paste backfill rheology can be determined using existing techniques and which mix and system variables have the greatest influence on transport pressure loss. Data from lab-oratory-scale pumping tests were used to produce a rheologic model of flow behavior for comparison, and a statistical analysis was conducted to determine the most significant factors affecting transport pressure loss.

Jan 1, 1994

By D. Neuschiltz, M. Witthaut, R. Cremer

"Metastable (Ti,Al)N coatings with fee structure have been shown to exhibit superior performance as compared to TiN under conditions of wear at elevated temperatures due to their better oxidation resistance and hardness. The oxidation resistance of these coatings increases significantly with increasing Al-content. However, the deposition of (Ti,Al)N films with Ti/ Al ratios below about 30/70 leads to a hexagonal structure which is not suitable for tribological coatings. Only little is known about the location of the cubic to hexagonal phase transition and hence about the optimum composition of (Ti,Al)N hard coatings.To determine the position of this transition, Tii-xAlxN films with different Ti/Al ratios were deposited on high speed steel at substrate temperatures between 100 and 700 °C by means of reactive MSIP. The composition of the films was determined by electron probe microanalysis (EPMA) and X-ray photoelectron spectroscopy (XPS), the crystallographic structure by thin film X-ray diffraction (XRD).It could be shown that in case of deposition temperatures of 300-700 °C a two-phase region exists in the metastable TiN-AlN phase diagram, which expands with increasing temperature, wheras at 100 °C substrate temperature no two-phase region was observed. But in opposition to the phase diagram known from literature, which is based on thermodynamic estimations, the detected two-phase region is narrow for typical PVD temperatures, thus allowing the deposition of cubic single-phase Al-rich (Ti,Al)N hardcoatings for tribological applications. Based on these results, a new Ti1-xAlxN film with x = 0.62 has been developed, which showed an increase of oxidation resistance by a factor of 4."

Jan 1, 1998

By J. A. Bakken

Thermal plasmas are interesting for a wide range of metallurgical and chemical processing applications. The 300 kW experimental reactor PRESS, which has been in use since 1987, is operated in the transferred arc mode with three or one plasma torches . Tests include remelting of silicon fines and production of ultrafine silica. Work on a novel three stage process for production of silicon metal is under way. A 1:1 model of the plasma reactor is used to measure the wall heat flux distribution calorimetrically. The cold walls of this model are divided into several water-cooled sections. The same plasma torches as in the real hot-wall reactor are used. In parallel to the experiments and calorimetric measurements theoretical work is done on numerical modelling of one and three transferred arcs. A modified version of the flow simulation program FLUENT from Creare Ltd. is used.

Jan 1, 1991

THE furnace described in this paper was installed and has been used by the writer for the melting of rich gold-bearing material, and has given complete satisfaction. It may, therefore, prove of interest to other metallurgists who are faced with a similarproblem. A furnace of this type should be most suitable for the reduction of "cyanide preeipitate," "charcoal ash," "anode sludge," &c. formerly the melting was done in fire-clay crucibles, using coke or crude oil as fuel, but this method is costly, slow, and unsatisfactory. A small water-jacketed blastfurnace was also tried on this material after briquetting it, but was discarded in favour of the electric furnace. The furnace may be described as a simple form of the Heroult resistance furnace, with an adjustable upper electrode and a fixed bottom electrode. This is in accordanee with Stansfield's classification of electric furnaces. The heating is mostly due to the resistance offered the current by the molten slag. The melting chamber consists of a steel drum 14 in. in diameter and 21 in. high, and is lined with silica bricks specially made to fit the shell. The internal diameter is G in. The bricks contain 92 % silica, are made from calcined quartzite bonded with fireclay, and are similar in composition to those used for lining steel converters. They are set in a mixture of finely-ground quartzite and clay, and well dried out. The shell is bolted to a steel plate, which forms the decking of a truck running on rails, so that the furnace can be moved under ahood for carrying off the fumes. A cast-iron slag spout is bolted to the shell below the tapping hole, which is 4 in. from the bottom of the shell. Opposite this another hole 1 in. in diameter is drilled through the shell and lining for the passage of the lower...

Jan 1, 1918

By R. A. Campbell

The electric smelting of five lowgrade Canadian manganese ores has been investigated at the Mines Branch, Department of Mines and Technical Surveys, Ottawa. Ferromanganese, silkomanganese, and spiegeleisen were produced 1by special smelting processes from these ores since the latter were too low grade to be treated by conventional smelting methods. In one case the results were considered to be sufficiently promising to justify the construction of a pilot plant, by the Company concerned, for the further development of the process.

Jan 1, 1956

By R. A. Campbell

Pig iron and silicospiegeleisen were produced experimentally from a very low-grade manganiferous iron ore from Steep Rock, Ontario, by a two-stage electric smelting process. The most favourruble operating conditions were determined for each stage. Cement clinker then was made by calcining the slag from the second stage of smelting, with additional limestone and alumina. (This slag would normally be a waste material). The cement clinker produced had the composition of commercial Portland cement, and met the physical test requirements of the Canadian Standards Association Specification A5-1951 for normal Portland cement as well as could be expected for a material produced on .such a small scale.

Jan 1, 1958

By G. E. Veins

A three-phase, continuously-operated, 250 kv.a. electric smelting furnace has been installed at the Mines Branch, Department of Mines and Technical Surveys, Ottawa, for the experimental treatment of ores and by-products of interest to the Canadian mining, metallurgical, and chemical industries. In the operation of this furnace particular emphasis is placed on the accumulation of quantitative data which will be useful in determining the most suitable smelting technique and the nature of the products, and in arriving at preliminary conclusions regarding the cast of power and electrodes. The results obtained in the experimental smelting of iron, manganese-iron, titanium- iron, nickel, and chromiumiron ores, and of a number of industrial by-products, clearly show the value of such treatment for materials of this type.

Jan 1, 1957

By G. E. Veins

This paper summarizes an investigation in which beneficiated ilmenite ore was smelted in a continuous, three-phase, 250 kv.a., open-top electric furnace. Minus %. inch ore was smelted, using the standard method. Fine ore, in the order of minus 14 mesh, was smelted in the briquetted form by the open bath method, and in the unagglomerated form by the cold dry-top method. The latter was shown to be superior. The data obtained .are discussed at some length. During the investigation, slag aver-aging 82.5 per cent Ti02 was produced over a period of 87 hours, the maximum being 85 per cent. Such slag should .be particularly attractive for the production of titanium tetrachloride, from which titaniurn metal is produced. The advantages of using paper-mill bark for producing a furnace charge of low bulk density, as required in cold dry-top smelting, were emphasized.

Jan 1, 1957

By Jeffery L. Kohler

The research and development of a pattern recognition system which can predict incipient failures and safety hazards in the mine power network is described. An examination of mine electrical safety hazards revealed they are often related to the electrical equipment down-time experienced on mine sections. Based on this, a method is proposed that can improve both production and safety, without compromising either. Equipment failure modes are examined to illustrate how the ultimate failure can be predicted for enough in advance to allow a convenient and safe repair, followed by a discussion of actual monitoring system performance. Finally, the paper is concluded by projections of the system's utility to industry.

Jan 1, 1977

By Jessica M. Wempen, Dallan J. Coons, Bailey S. Simmons, Michael K. McCarter

Gate-road yield pillars are subject to increases in stress as the longwall face advances toward the pillars. Abutment loading conditions are important to gate-road layout and support design in longwall mining systems. Ground support systems are often designed based on mine experience [1,2]. Convergence monitoring is one method of ground support monitoring that can be used to infer increases in pillar stress. Convergence of a yield pillar was measured regularly over the course of six months as the longwall face approached and passed the pillar. Measurements were collected at eight locations surrounding the pillar. The convergence measurements contribute to the knowledge of when yield pillar abutment loading, caused by the encroaching longwall, is first detected. Knowing when abutment loading begins to yield the pillars can help define when standing secondary roof supports are required for head-gate entry access for specific geologic and mining conditions. 

By Jessica M. Wempen, Dallan J. Coons, Bailey S. Simmons, Michael K. McCarter

Gate-road yield pillars are subject to increases in stress as the longwall face advances toward the pillars. Increases in pillar stress can be inferred by measuring roof/floor convergence surrounding the pillar. This paper presents a case study of convergence measurements surrounding a two-entry gate-road yield pillar in the head gate of a coal mine. Convergence was measured over a six-month period, as the longwall face approached and passed the pillar. Measurements were collected at eight locations surrounding the pillar: four locations in the travelway and four locations in the beltway. In addition to convergence stations, the pillar was instrumented with an array of seismometers. In future analysis, convergence measurements will be compared to seismic interpretations. This study reports on the geology and geometry of the longwall panel, the roof and rib support, the change in convergence over time, and the physical properties of coal and parting. Additionally, the convergence measurements are compared to pillar safety factor distributions derived from a finite element model. The convergence measurements contribute to the knowledge of when yield pillar abutment loading, caused by the encroaching longwall, is first detected. Knowing when abutment loading begins to yield the pillars can help define when standing secondary roof supports are required for head gate entry support.

By Jessica M. Wempen, Dallan J. Coons, Bailey S. Simmons, Michael K. McCarter

Gate-road yield pillars are subject to increases in stress as the longwall face advances toward the pillars. Increases in pillar stress can be inferred by measuring roof/floor convergence surrounding the pillar. This paper presents a case study of convergence measurements surrounding a two-entry gate-road yield pillar in the head gate of a coal mine. Convergence was measured over a six-month period, as the longwall face approached and passed the pillar. Measurements were collected at eight locations surrounding the pillar: four locations in the travelway and four locations in the beltway. In addition to convergence stations, the pillar was instrumented with an array of seismometers. In future analysis, convergence measurements will be compared to seismic interpretations. This study reports on the geology and geometry of the longwall panel, the roof and rib support, the change in convergence over time, and the physical properties of coal and parting. Additionally, the convergence measurements are compared to pillar safety factor distributions derived from a finite element model. The convergence measurements contribute to the knowledge of when yield pillar abutment loading, caused by the encroaching longwall, is first detected. Knowing when abutment loading begins to yield the pillars can help define when standing secondary roof supports are required for head gate entry support.

By Ramin Motamed, Farshid Ghazavi, Joseph A. W. Toth

"Post-disaster reconnaissance of areas affected by earthquakes has documented extensive damage to buildings with shallow foundations located in liquefaction-prone areas. Currently, estimation of liquefaction settlement is based on empirical correlations that evaluate settlement in the free-field environment and are based on one-dimensional consolidation. However, observations have shown that liquefaction settlement under buildings can be considerably greater. This research is based on a series of 1- g shake table experiments using a transparent soil box to reproduce liquefaction-induced building settlement. Building settlements were evaluated using a scaled model of a building foundation representing a 1-2 story building. Comprehensive parametric study was carried out to establish the effects of several parameters on free-field and building settlements such as building width and thickness of liquefiable soil layer. The experiments utilized accelerometers and pore-water pressure sensors to monitor ground accelerations and buildup of pore-water pressures in both the free-field and model building footprint. Results of these experiments are compared to available centrifuge tests and field observations and conclusions are drawn with respect to the potential scaling effects. Lastly, this paper discusses the feasibility of installing helical piles as a mitigation strategy to reduce the building settlements by presenting some of the exploratory experimental data obtained from this series of 1-g shake table tests.INTRODUCTIONThe 2010-2011 Canterbury earthquake sequence and the 2011 Great Tohoku earthquake are some of the most recent examples where large numbers of low-story structures sustained damage resulting from liquefaction-induced settlements. This damage has commonly been observed in residential and commercial areas developed over loose, unconsolidated and saturated coarse grained soils resulting from both natural and man-made deposits. Damages incurred from the 2010-2011 Canterbury earthquake sequence occurred in the largely unconsolidated fluvial environment bordering the Avon River in Christchurch (Henderson 2013). Similar damage was also incurred during the 2011 Great Tohoku earthquake where liquefaction of soils occurred in both young alluvial deposits and fill materials (Ashford et al. 2011). Figure 1 presents typical modes of failure to structures resulting from the effects of liquefaction. Current practices in evaluation of liquefaction settlement rely on empirical correlations (Tokimatsu et al. 1987; Ishihara et al. 1992) developed for liquefiable soils in the freefield environment (Dashti et al. 2010a). However, recent observations of the performance of foundations suggest that settlement of rigid shallow foundations in liquefiable soils are commonly greater than those predicted in the free-field. Therefore, new correlations should be developed to better predict the degree of settlement of shallow foundations in liquefiable soils. Current research is beginning to focus on the mechanisms of settlement during liquefaction in regards to confining stress, pore-water pressure and shear stress induced from foundations (Dashti et al. 2010b)."

Jan 1, 2016

By Monica C. Pinto, Gustavo H. Nalon, José C. L. Ribeiro, Rita de C. S. S. Alvarenga, Leonardo G. Pedroti, Lucas A. F. Fioresi

This study aims to evaluate the influence of mortar’s mechanical properties on the behavior of clay masonry. Experimental studies were performed using prisms of clay blocks under axial compression. The clay units were produced with a clay from Tres Rios, Rio de Janeiro, Brazil and had compressive strength of 4.9 MPa. Two mortar compositions were used, which had compressive strength of 94.7 and 50.4% of the clay blocks’ net area compressive strength. It was noticed a slight increase on the prism’s compressive strength with the increase of the mortars’ compressive strength and stiffness. Prisms made with flexible mortars had a ductile failure and collapsed under lower compressive stresses, while prisms made with stiff mortars resisted higher compressive stresses, but had a brittle failure ,crushing the blocks. A very strong mortar is not recommended. Using more flexibl mortars does not compromise the strength and stiffness of the masonry and prevents an excessively brittle failure of the structure.

Mar 1, 2017