Search Documents

By Enver Alan

This Research & Development (R&D) study was conducted in the field of applied blasting engineering in Ethiopia, within the AKH Railway Project, which was built in Girena, within the boundaries of the province of Mersa, in the Basalt Quarry at km 346, Ashangi Formation, occured in Eocene geological time in the aphanitic trachibasalt.

Feb 1, 2020

By Zbigniew Zurecki

The selection of atmosphere composition is critical for controlling surface quality of reactive aluminum alloys during solution treatments. An improper selection of annealing atmosphere can result in surface blistering in AI-Mg and sub-surface depletion of lithium in AI-U ingots. To determine optimum atmosphere compositions for homogenizing A1-Mg and Al-Li alloys, Ii number of exploratory experiments were carried out in air, nitrogen, and carbon dioxide based atmospheres including reactive impurities or additive such as moisture and sulfur hexafluoride. This paper describes the influence of these atmospheres on high-temperature oxidation and sub-surface defects. The results are discussed in terms of the change in Pilling-Bedworth ratio.

Jan 1, 1996

By Garg. D.

Premixed bronze powders are widely used to produce a wide variety of P/M components including bearings and bushings by the powder metal industry. The physical and mechanical properties of sintered bronze components such as dimensions, strength, microstructural characteristics, and sintered density are well known to change with sinlering furnace design, particle size distribution in powders, green density, preheating and sinlering time" and temperature, and protective atmosphere flow rate. " However, not much is known about the effect of protective atmosphere composition on physical and mechanical properties of sintered bronze components; This paper describes effects of protective atmosphere composition and sintering temperature on physical and mechanical properties of sintered bronze components

Jan 1, 1996

By Robert A. Cummings

Disintegration of the immediate shale roof in coal mines interferes with ventilation, production, and safety. The effect is seasonal and correlates with high levels of moisture in the intake ventilation air. Disintegration, though not completely understood, is caused by shale dilation and weakening upon exposure to atmospheric moisture. Fluctuating moisture conditions are particularly deleterious, and may be at least partially controlled by "tempering" the air before it is brought to the working places. Roof behavior was studied in an operating mine during a 12-month monitoring period. This approach can be used in developing criteria to reduce or prevent shale roof deterioration.

Jan 1, 1981

By Wantae Kim, Jaechun Lee, Tatsuya Oki, Sungbaek Cho, Sangbae Kim

"Effect of attrition scrubbing on the recovery of platinum group metals(PGMs) from automotive catalytic converter was discussed. The attrition scrubbing as comminution and separation process was effective for the recovery of the catalyst layer, ?-alumina, from ceramic supporting matrix, cordierite, by physical impact and shearing action between particles in the scrubbing vessel. The catalyst layer was dislodged from the surface of the supporting matrix into fine particles less than 45µm by attrition scrubbing. The production of fine fraction less than 45µm increased as the residence time for attrition scrubbing increased. The fine fraction obtained at the residence time of 40min contained 19.25% CeO2, 1.93% ZrO2 and 418.8ppp PGMs. The recovery of ?-alumina in the fine fraction increased as the residence time increased. Simultaneously, the recoveries of CeO2, ZrO2 and PGMs increased and reached up to 82.9% CeO2, 78.7% ZrO2 and 78.9% PGMs at the attrition scrubbing time of 40min. The production of the fine fraction and recovery of ?- alumina increased when the solid concentration and initial feed size increased.IntroductionThe automobile catalytic converters contain appreciable amount of PGMs. Currently several million tons of used catalytic converters are disposed annually worldwide, each containing about 0.5-1g of platinum and 1-2g of all PGMs1). The recovery technologies of PGMs from spent catalytic converters have been thoroughly reviewed by numerous researchers since last decades. Two types of methods, wet and dry processes, have been commercially operated. In the wet process, the PGMs on the spent catalytic converters were dissolved mostly in the form of chlorocomplex, MCl6 2-, by contacting with aqueous solutions. Subsequently the resulting solutions are treated to concentrate and the precious metal ions are reduced by introducing metals such as Al, Fe and Zn in the concentrated system2). In the dry process, the spent catalytic converters are melted, in some case with CaO, at an elevated temperature to produce a low viscous slag. The PGMs in the melt are separated by allowing them to adsorb on Fe or Cu having high specific gravity7). Although highly pure precious metals could be obtainable, the recovery technologies of PGMs currently operated seem not to be cost-effective since PGMs embedded in these types of catalytic converters are present in very small quantities."

Jan 1, 2008

By Brahm Prakash, R. Schuhmann

Chemical conditions for flotation and nonflotation of quartz with oleic acid as collector and barium, calcium, aluminum, iron, and tin as activators were studied using a simple vacuum-flotation technique in glass-stoppered graduates. The detailed study of barium activation led to an interpretation based on ideal Langmuirian chemisorption.

Jan 1, 1950

By Brahm Prakash, R. Schuhmann

Chemical conditions for flotation and nonflotation of quartz with oleic acid as collector and barium, calcium, aluminum, iron, and tin as activators were studied using a simple vacuum-flotation technique in glass-stoppered graduates. The detailed study of barium activation led to an interpretation based on ideal Langmuirian chemisorption.

Jan 5, 1950

By Muhammad Zaka Emad

Cemented rockfill (CRF) is a mixture of rock aggregate and binder slurry. It is a stiff backfill, it is fast curing, its operation is simple, placement rate is reasonably high and no drainage is required. The main demerit of CRF is failure of exposed faces causing ore dilution, which can be associated with the fill placement method. This paper discusses the effects of two placement methods being practiced by mines and numerical modelling is used as a tool to evaluate stability of the backfill column. In the first method, practiced in longitudinal retreat mining of a narrow vein deposit, the rockfill is hauled and dumped into the stope with a LHD scooptram. Once dumped, cement slurry is sprayed into the stope. In the second method, a raise situated centrally above the mined stope is used to convey already mixed CRF into the stope. Stopes are mined out transversely in primary and secondary blocks in a sublevel stoping system. Problems of poor mixing in combination with both placement methods are discussed. The two backfill placement methods are analyzed for blast induced vibration damage using the dynamic Flac3D modelling technique accounting for rock mass and fill damping characteristics, and a pressure wave is used to simulate the blast vibrations. Fill heterogeneity has also been considered for the two cases and results are compared.

Jun 1, 2012

By G Huggins

Excavation in underground jointed rock masses creates cavities into which the surrounding rock mass deforms. Deformations, besides intact rock deformation, include mechanistic deformations such as slip and rotation. In this paper deformational moduli were measured for prototype and blocky (jointed) models using elastic analogue methods for stopes from MIM LimitedÆs Lead Mine. The blocks for the models were defined in terms of the prototypeÆs joint sets, their spatial separations, orientations and average friction characteristics. From dimensional analyses, a relationship between prototype and model deformations was used to predict stope mid-span deformations. The results of this physical modelling work, conducted in the 1970s, motivated an investigation into the electro-treatment of tailings backfill to achieve improved strength and stiffness characteristics. Tailings backfill containing fines and having a high clay content can be electrically dewatered, and at times grouted, cemented, ion exchanged or agglutinated, to achieve relatively high magnitudes of strength and stiffness. These treated tailings stiffnesses can reduce the deformation magnitudes within a rock mass and, in doing so, reduce problems encountered in mine pillar extraction. The application of these tailings modification techniques is examined in relation to the elastic analogue methods.

Jan 1, 1998

By S. Banisi, M. Poorkani, M. Farzaneh, M. Askari

"At the Sarcheshmeh copper mine 40,000 t of ore per day with an average grade of 0.9 % Cu is ground to 70% passing 75 microns. Grinding is effected in 8 parallel lines of 8 x 5 m ball mills in a closed circuit with cyclones. The make-up balls are 80-mm forged alloy steel balls and the average ball consumption is 750 gh of ore ground. In order to optimize ball size distribution inside the mill, based on the previous investigation instead of using only 80 mm make-up balls a combination of 80 and 60 mm (75% to 25% by weight) ball charge was used in one of the mills. To evaluate the performance of three ball types namely forged alloy steel balls (A), ductile cast iron (C), high chromium cast iron (D) and also a combined (80 and 60 mm) charge of forged alloy steel balls (B), four identical parallel mills were charged accordingly. These four mills were sampled during a period of six months. The amount of material finer than 75 microns of cyclone overflows was selected as a criterion for the performance evaluation. It was observed that in a mill with the combined make-up balls the amount of fine produced was 4% higher than the other mills. The consumption of ball types A, C and D were 730, 710 and 534 g/t, respectively. The results of laboratory flotation tests showed that due to an improvement in the production of fines an increase of 1.4% in the overall copper recovery is obtainable. Due to the promising results, the new make-up ball regime was implemented in all mills in the plant.INTRODUCTIONThe Sarcheshmeh copper ore body which may rank as third or fourth largest in the world contains 1 billion tonnes averaging 0.90 % copper and 0.03 % molybdenum. It is located southeast of Iran and has been processing 40,000 t/d of ore since 1982. The mine produces 100,000 tonnes of copper and 2,200 tonnes of molybednite concentrate per year. After three stages of crushing, the ore with a F80 of 12.7 mm is fed to 8 parallel ball mills in closed circuit with cyclones to produce a product 70% finer than 75 microns. The concentrate of the first stage of flotation is reground and the tailing constitutes the main component of the plant final tailings. A concentrate with an average grade of 31% Cu is obtained after cleaning and re-cleaning stages. Total recovery of the plant varies between 83 and 87 % depending on the operating conditions and ore type."

Jan 1, 2002

By Ö. Genç

In this paper, full-scale mill data collected from three different circuit configurations in cement plants demonstrated the size reduction performance of dry ball mills in relation with the ball size classification achieved by the classifying liners used in the grinding compartments. Findings indicated that, breakage rates at the last 2 ~ 4 meters of the mill are not sufficient to give reasonable size reduction ratios for the production of fines. Application of only damming rings without classifying liners resulted in inverse ball size classification which lead to reduction in size reduction performance thus specific breakage rates.

Jan 1, 2014

By Saurabh Rastogi, Vikram Shishodia, B. Pitchumani

Comminution is a unit operation which consumes major part of energy in mineral processing industries such as fertilizer production. Ball mills are widely used for size reduction of a given ore to the liberation size that is required in further beneficiation processes. In grinding of materials much effort is concentrated on control of top size of the product and this results in production of fines, also creates secondary problems of pollution due to the difficulty in the collection of fine particles. The present work has been carried out to control product size distribution for rock phosphate grinding in an Industrial Ball Mill of 600 TPD. The plant data are taken for a given feed distribution and mill operating conditions. The information at various Ball Size distributions are collected. The comminution functions such as specific rate of breakage and breakage distribution functions are estimated by back calculation technique to solve the mass balance equation. A simulation program is written to study the product size distribution obtained for various ball size distribution.

Jan 1, 1993

By Mahmut Altiner

Magnesium is listed as a key critical raw material in a report by the European Commission that evaluated raw materials based on supply risk versus economic importance [1]. It has extraordinary properties, such as nontoxicity, inertness, high melting point, stability, low weight, chemical resistance, electrical insulation, optical transparency, corrosion-resistant behavior and refractory nature. It is widely used in the areas of agriculture; the environment, for antibacterial and water-purification purposes; electronics; automotive; drug delivery; ceramics; construction, as filler in brick; and concrete production, in the forms of magnesium oxychloride and magnesium oxysulfate. Magnesium oxide (MgO) particles can be produced through the calcination of magnesite ore at different calcination conditions depending on the desired quality of the product, classified as fused (2,800 °C), dead-burned (>1,400 °C), hard-burned (1,000–1,400 °C), or light-burned MgO (700–1,000 °C) [2]. However, the global availability of magnesite ore is limited.

By Mahmut Altiner

This study aimed to produce magnesium oxide (MgO) particles with different properties from dolomite ore using an experimental procedure comprising four stages: sample preparation (S1), HCl leaching (S2), precipitation (S3), and calcination (S4). Three different base sources (NaOH, KOH, and NH4OH) were used as precipitant in the third stage to obtain magnesium hydroxide [Mg(OH)2] from a leachate solution, which was obtained in the second stage. Next, Mg(OH)2 particles generated by different alkali sources were calcined at various temperatures from 600–1000 °C for different durations (1–5 h). The effect of these base types on the properties of each product was investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), Brunauer–Emmett–Teller (BET), atomic force microscopy (AFM), and wet chemical analyses. The experimental results indicated that each product was identified as periclase (MgO) mineral, which was produced with a specific surface area (SSA) of 4.49–44.54 m2 /g depending on the production conditions. The surface roughness of the MgO particles increased with increasing calcination temperature. SEM analyses showed that MgO particles produced at a temperature of 600 or 800 °C were amorphous, indicating that the process was not influenced by the base type, but MgO crystals were smooth when the calcination temperature was 1000 °C. Finally, it was determined from all experimental findings that MgO particles produced via the addition of NaOH have superior properties (such as higher SSA and lower surface roughness) compared with MgO particles produced with KOH or NH4OH as the alkali source. These properties led to great improvement of its usability in industry.

By Jinliang Zhang, Jian Pan, Deqing Zhu

"Limestone and burnt magnesite were added to vary MgO content and basicity (CaO/SiO2 ratio) of pellets for investigating their influences on the properties of specularite pellets. At fixed MgO content, the addition of limestone does not affect on the properties of green balls significantly. The addition of burnt magnesite has obvious influence on the quality of green balls, especially on the thermal shock temperature. Without burnt magnesite, the thermal shock temperatures are about 400°C, and, the thermal shock temperature increases to 600~630°C by adding burnt magnesite. For preheated pellets, when the burnt magnesite is added, the compressive strength will be decreased. For roasted pellets without burnt magnesite, the calcium additives can form binding phase of calcium-ferrite, and suitable liquid phase will improve recrystallization of hematite, but excessive liquid will destroy the structure of pellets, so the compressive strength of pellet increases firstly and then decreases. When adding burnt magnesite, the compressive strength will increase as the basicity increases. When the basicity is more than 0.2, the compressive strength of the pellets various MgO content and basicity is above 2500N/pellet and then MgO-bearing fluxes can be added to prepare pellets with good high temperature properties.IntroductionWith the rapid development of the steel industry in China, oxidized pellets, possessing good mechanical and metallurgical properties, are becoming indispensable burdens for blast furnace ironmaking [1-3]. However, this has resulted in the shortage of domestic iron concentrates, so many Chinese steel plants begin to use imported hematite concentrate to prepare pellets. Compared with magnetite pellets, the hematite pellets require high roasting temperature and narrow roasting temperature range (1300–1350°C) and possess low compressive strength [4,5].1"

Jan 1, 2012

By Mark Jolly, Nasim Soleimanian

"During the last 20 years CFD (Computational Fluid Dynamics) has been used as a tool to aid furnace designers and manufacturers to improve energy efficiency and effectiveness of glass furnaces. However as the models are maturing the effect of feeding equipment used to push the raw material into the furnace has not been included in the process models. This paper investigates the effects of batch pattern in the melt space caused by charging equipment on the energy efficiency of the furnace focusing on the melting zone. A simple batch patterns sensitivity study has been performed using purpose built software (Glass Furnace Model-GFM). It is concluded that in order to further reduce the energy consumption of the furnace it is necessary to model the batch charging process in more detail to find more opportunities for improvement.Introduction Glass manufacturing is a conservative industry which applies to all the four major segments (float glass, container glass, fiberglass, and specialty glasses). Risks due to the high capital investment, very long service life of the furnaces, and the demand for high performance and quality from the outset translates into evolutionary progress rather than revolutionary. The main problem facing glass manufacturers are the financial cost of manufacture, its impact on the environment, and mounting pressure imposed by the authorities for greener manufacturing and reduction in emissions.The main energy intensive activities involved in continuous glass manufacturing are: the need for high temperature to create and maintain the viscous flow, homogenisation of glass melt (melt residence time), and maintaining the two to achieve continuous output of glass at the right quality. The high temperature and long duration of homogenisation has resulted in the design oflarge furnaces, which have high energy consumption, low specific performance, and high C02 emissions. As an example in the container glass sector the most efficient furnace has a specific primary energy consumption of 3.8 GJ /tonne of glass at a level of 50% cullet in the batch. Even very small improvements in efficiency by optimising operation would have a high impact [1-14]. Given the conservative nature of the industry and the costs involved in experimental data gathering, CFD modeling of the process has been used extensively during last two decades to not only improve our understanding of the process but also as a tool in predicting possible optimisation windows, e.g. Glass Furnace Model ( GFM), a commercially available piece of software that has been developed to optimise furnace operation."

Jan 1, 2013

By Monica R. Garcia, Antonio Alberto S. Correia, Paulo J. Venda Oliveira

"The aim of this paper is to analyze the creep behavior of a Portuguese soft soil stabilized with binders in one-dimensional conditions, based on oedometer creep tests. The study focuses on the analysis of the effect of the binder content and binder type on the creep behavior of a stabilized soil. The results show that the best binder type for this soil, in terms of creep behavior, is composed of Portland cement and fly ash with a dry weight proportion of 75/25, as this promotes the development of secondary pozzolanic reactions. The results also show the decrease in the secondary compression index with the increment of the binder content, since it promotes an increase in the cementation bonds between soil particles. The general analysis of the results shows a clear dependence on C??and qu, until values of qu of 1500 kPa; after that this relationship is negligible.INTRODUCTIONThe geotechnical structures (such as embankments, dams and buildings) built on organic soils exhibit notable creep deformations, which increase the maintenance and exploitation costs and can even compromise their functioning. To attenuate the creep effects of the soft ground, some improvement techniques are frequently used, such as preloading or reinforcing the soil foundations with vertical rigid inclusions, like concrete piles, stone columns or deep mixing columns (DMCs). However, the installation of DMCs in the soft ground induces (via the arching effect) a transfer of stresses from the soft soil to the DMCs, which causes an increase in the creep settlement on the DMCs (Venda Oliveira et al. 2011).Notwithstanding the fact that the creep behavior of clays has been the object of several studies (Leroueil et al. 1985; Mesri and Castro 1987; among others), the study of the creep behavior of soil-binder admixtures has been practically ignored by the scientific community. The few studies on this theme have revealed that a stabilized soil’s creep behavior is dependent on: the type of binder (Venda Oliveira et al. 2013), the binder content (Correia 2011; Bobet et al. 2011; and Venda Oliveira et al. 2013), the stress level applied during the creep phase (Venda Oliveira et al. 2013), the organic matter content of the natural soil (Venda Oliveira et al. 2012; 2014), and the curing conditions (humidity, vertical stress applied during curing, and curing time) (Correia 2011; Venda Oliveira et al. 2012).The aim of this paper is to contribute to a better understanding of the creep behavior of a soil-binder admixture, by examining the results of oedometer creep tests. The study focuses on the analysis of the effect of the binder content and binder type on the creep behavior of a stabilized soil. Additionally, the creep behavior is correlated with the effective vertical yield stress and the unconfined compressive strength (UCS)."

Jan 1, 2015

By C. Guo

The Mildred Lake Settling Basin (MLSB) is the largest disposal site for mature fine tailings (MFT) at the Syncrude Canada Ltd oil sands plant. Over the past years (since 1997), there has been a marked change in the consolidation behaviour of MFT in the MLSB, which is attributed to microbial activity. Methane-producing microorganisms, known as methanogens, have become very active, and large amounts of biogas (mainly methane) have been produced. In certain regions within the MLSB, gas bubbles are released to the water surface of the tailings pond. Continued field monitoring of the MLSB has provided convincing evidence of the rapid densification process (rapid water drainage from the tailings). This phenomenon contradicts the consolidation models for MFT developed over the past 20 years. The above phenomenon has also been reported at the oil sands tailings ponds operated by Suncor Energy Ltd. in Fort McMurray. This rapid densification has caused pumping challenges in the transfer of fine tailings from the Mildred Lake Settling Basin for the creation of composite tailings. The rapid densification of the MFT may also have potential positive effects in accelerating the reclamation of the oil sands fine tailings. A field and laboratory research program is underway to study the mechanism leading to the rapid densification phenomenon. Systematic field investigations were performed to determine the distribution and characteristics of the rapidly densified MFT. Gas bubble distribution on the water surface was mapped to determine the zones of different biological activities in the pond. These field investigations provided solid ground for further experimental and theoretical research. A number of small-scale column tests were carried out to observe the gas evolution and to measure the changes of some geotechnical parameters under different microbial activity. Also, a series of gassy MFT densification tests are being conducted to study the mechanism of the rapid densification of the MFT under microbiological activity. A review and discussion of the research program is given and some preliminary research results are presented in the paper.

Apr 1, 2005

By C. Guo, R. J. Chalaturnyk, M. MacKinnon, J. D. Scott

The Mildred Lake Settling Basin (MLSB) is the largest disposal site for mature fine tailings (MFT) at the Syncrude Canada Ltd. oil sands plant. Over the past years (since 1996), there has been a marked change in the densification behaviour of MFT in the MLSB. Methane-producing microorganisms, known as methanogens, have become very active, and large amounts of biogas (mainly methane) have been produced. Continued field monitoring of the MLSB has provided convincing evidence of the rapid densification process (rapid water drainage from the tailings) at the area with intense microbial activity. This rapid densification has caused pumping challenges in the transfer of fine tailings from the Mildred Lake Settling Basin for the creation of composite tailings. It may also have potential positive effects in accelerating the reclamation of the oil sands fine tailings. A field and laboratory research program was carried out to study the mechanism leading to the rapid densification phenomenon. A review and discussion of the research program is given and some results from the field investigations and small-scale column tests are presented in this paper.

Jan 1, 2007

By Lorenzo Reyes-Bozo, Ronaldo Herrera-Urbina, Pablo Higueras, Alex Godoy-Faúndez

"The copper mining industry in Chile and perhaps in other countries as well is faced with the challenge to implement the best practices in order to achieve a sustainable and more environment-friendly growth. Relationships between mining industry and society have been historically complex due to its environmental impacts. Whereas the ore grade has declined continuously, this has involved an intensive energy and water consumption thus increasing operational costs at different stages of the concentration process. In the case of copper sulphide ore concentration, froth flotation is the main technology used worldwide. The amount of the different chemical reagents used in flotation plants (i.e., collectors, depressants, frothers and modifiers) affects significantly production costs and has a negative effect on the environment as well. The objective of this research work was to evaluate the use of biosolids and their main components (i.e., glucose, proteins and humic substances) as more environment-friendly flotation collectors for chalcopyrite and molybdenite. For this purpose, microflotation tests were conducted in a modified Hallimond tube. In addition, FTIR and zeta potential experiments were performed to investigate the interaction of biosolids with these sulphide minerals. Biosolids and their main components may interact through physical and chemical ways due to different affinities with such sulphide minerals as chalcopyrite, pyrite and molybdenite, which are present in copper sulphide ores. In alkaline pHs, biosolids and their main components make the zeta potential of the sulphide minerals investigated more negative. These results may provide important information concerning the behavior of the main sulphide minerals in the concentration of copper sulphide ores at industrial scale, wherein mill processes could affect their surfaces properties. Therefore, biosolids and their main components may open an opportunity to be used in copper sulphide flotation plants to partially replace conventional reagents, which are more hazardous and less environment-friendly."

Jan 1, 2014