Search Documents

By Ting Cheng, Guang-sheng Wei, Ze-shi Yang, Ling-zhi Yang, Yu-feng Guo

The application of the bottom-blowing in the steelmaking process of EAF can effectively shorten the mixing time of the molten bath, accelerate the removal of carbon, phosphorus and sulfur, and improve the production efficiency and product quality. Information about the effects of changing molten steel velocity during the smelting process would help to accurately model molten bath dynamics. In this study, numerical simulation software was employed to simulate the EAF steelmaking process under variable eccentric bottom-blowing gas flow situations. Velocity field data were obtained for the different bottom-blowing schemes. When other nozzles’ bottom-blowing gas flow rates were maintained at 133 L/min, the average velocity of molten steel in EBT (Eccentric Bottom Tapping Area) was increased from 2.8 10−3 to 3.4 10−3 m/s with the eccentric gas flow rate of bottom-blowing from 100 to 267 L/min, the average velocity of molten steel in the bath increased from 4.3 10−3 to 4.6 10−3 m/s with the eccentric gas flow rate of bottom-blowing from 100 to 267 L/min.

Mar 1, 2018

By Chen-Ming Kuo, Esher Hsu

Energy recovery of livestock waste can not only reduce waste pollution but also generate renewable energy and further create economic bene fits. Currently, most of livestock waste in Taiwan is treated as waste without efficiently recycled. This paper aims to explore and evaluate the energy recovery of livestock waste in Taiwan and further provide policy suggestions. Study results show that small farming scale of livestock industry in Taiwan leads to a lower efficiency of biogas energy recovery. Besides, the environment with relative low price of electricity and high invest cost for power generation plant is hard to provide incentive for implementation of energy recovery which has further caused difficulty on policy promotion for renewable energy recovery of livestock waste in Taiwan. Policy reform with increasing FITs and differentiated purchasing rate for biogas power is suggested to stimulate energy recycling of livestock waste in Taiwan.

Mar 1, 2017

By Stephen Northey, Nawshad Haque, Terry Norgate

"Life cycle assessment (LCA) is a recognized tool to evaluate various processing routes for metal production. Declining ore grades and higher specific energy requirements for primary metal production put greater emphasis on recycling. Greenhouse gas (GHG) emissions of steel and aluminium metal production were quantified with recycling scenarios using material recovery facility (MRF) data from the database of SimaPro LCA software. The GHG footprint of the MRF is relatively minor compared with that of associated transport during collection (i.e. 10 times more than MRF) of curbside recyclable material. Additionally, if the bulk recyclable material is sent overseas (i.e. Australia to China) from the MRF for further processing, the GHG footprint of shipping can significantly be larger compared with the sum of the collection and MRF (assuming electricity is from same source). Thus opportunities exist for reducing GHG emissions from secondary metal production if it is processed close to the MRF.IntroductionIt is a challenge to recycle metals significantly, although theoretically infinite recycling is possible due to their elemental nature. Leaks from the metal stocks in society occur through corrosion, wear and dispersive uses, or via land filling or similar activities that return metals to the earth. In order to provide a technically sound and transparent assessment of metal recycling, a methodology such as life cycle assessment (LCA) should be used. By taking a life cycle perspective, the beneficial recycling properties of metals can be evaluated in a manner that enables appropriate comparisons with other materials or product systems that do not have recycling loops. In practice, mixtures of primary and secondary metals are often used in new products, and also at the end-of-life various processing methods are used for recycling.The difficulty of introducing recycling into LCA is to set the right boundaries for the different flows ending in different product systems. It is a question of which observed material flow belongs to the first product system and which one to the second or subsequent systems. Recycling can be part of any product LCA. However, it is often a complex issue which requires specific considerations. As pointed out by Yellishetty et al. and Birat et al. [l, 2], LCA practitioners are left with much freedom in allocation of environmental burdens to account for recycling, thus making subjective judgments on recycling and allocation of credits to recycling. This often makes it difficult to compare the results of LCA studies conducted by two different practitioners even on the same processes. As LCA is often used to define policy in government, business and society circles, it should be based on a sound, objective and unbiased description of recycling."

Jan 1, 2014

By R. C. Nascimento

It was investigated the effect of the addition of bentonite on the physical propertiesof pellets produced from fines of manganese ores. Cold-bonded pellets were produced. Pellets bearing up to 1 wt% of bentonite were submitted to strength compression resistance tests, fatigue of pellets to impact and maximum height of fall tests. A correlation of resistance of the pellets and time for curing were stablished. The produced pellets match the conditions for raw materials used in electric smelting hrnaces to produce manganese based ferro-alloys.

Jan 1, 1995

By C. S. Griffith

Lithium Australia NL (ASX:LIT) and ANSTO Minerals have been working together since 2015 on the development of halide accelerated leaching for the extraction of lithium from lithium-bearing micas, spodumene and clays. This technology has been termed SiLeach® process. The driving force behind development of the SiLeach® process, initially, was to develop a hydrometallurgical process to extract lithium from micas and spodumene without the need for the energy intensive, high temperature processing conventionally applied to lithium extraction. This driving force remains today and continues to hold promise in realising the value of previously under-utilised lithium resources. A comprehensive understanding of the technology and its applicability to the processing of micas and spodumene currently exists, and the flowsheet has been rigorously piloted. Production of battery grade lithium carbonate has been demonstrate

By Jorge Gibson, P. Chris Pistorius, Megha Jampani

Increased utilization of natural gas in blast furnace ironmaking can decrease both the cost and the carbon intensity of ironmaking, given current US natural gas prices. In this paper, three ways to utilize natural gas are compared: tuyère injection, prereduction of iron ore, and shaft injection. The basis for comparison includes coke replacement ratios, carbon intensity and furnace productivity. These were calculated using relevant mass and energy balances, a blast furnace productivity correlation based on the bosh gas flow rate, and measured and modeled prereduction kinetics. Of the natural gas utilization methods, prereduction has the highest effective coke replacement ratio (and hence the largest advantage in raw material cost), but is likely to have the highest capital requirement.

Mar 1, 2017

By De-qing Zhu, Feng Zhang, Jian Pan

Sintering performance of a series of sinter blends with high ratio of limonite was investigated. The metallurgical performance and mineralogy of product sinter were also examined. The results show that good sintering performance could be obtained when the ratio of limonite was below 43% in the blends of iron ore fines, while good microstructure and metallurgical properties were achieved under optimum sintering conditions. In contrast, sintering performance will rapidly deteriorate when the ratio of limonite is elevated up to 63% in the blends.

Mar 1, 2017

By Richard Elliott

Current methods for producing low-carbon manganese alloying materials for the steel industry are energy intensive and costly. To enable wider implementation of high Mn steel alloys, a novel solid-state Mn ore reduction strategy is therefore being investigated. This solid-state process, modelled on existing Direct Reduced Iron technology, employs a methane-containing atmosphere to reduce Mn ore pellets to a metal carbide. These pellets may then be smelted, yielding a Mn-rich master alloy. It is well established that CH4 is a suitable reductant for Mn ore powders; however, the reduction behaviour of industrially relevant Mn ore pellets by CH4 is poorly understood. The present work reports the results of an investigation undertaken to address this knowledge gap. The results of this study highlight the significantly different reduction behaviour exhibited by the Mn ore pellets relative to the ore powder under similar conditions and suggest that the diffusion of CH4 into the pellet interior is the limiting factor in achieving complete reduction.

By Satoshi Itoh

Phase equilibria and activities of the components in the liquid lead-antimony-oxygen temary system, which is of fundamental importance for discussing the recovery of lead and antimony from a used lead-battery, have been investigated at 1173 and 1223 K. The two liquid phases of metal and oxide were observed at the temperatures studied, and the tie lines indicating isoactivities were determined. The activities of PbO, Sb015 and Sb203 in the PbO-SbOu and PbO-Sb203 pseudo-binary systems were then obtained by applying the Gibbs-Duhem equation to the phase relation of metal-oxide equilibrium. Both in the pseudo-binary systems the activities exhibit negative deviations from Raoult's law. The vapor pressures of lead, antimony and lead oxide, antimony oxide were calculated by using the activities of the components in the lead-antimony-oxygen ternary system. As a result, an oxidation of antimony concentrated in an anode slime followed by evaporation as antimony oxide Sb406 was found to be considerably effective for the recovery of lead and antimony from a used lead-battery.

Jan 1, 2003

By Hye-Sung Kim, Dong-Wha Kum, Gyeungho Kim

"Mechanical alloying is an effective way to finely distribute inert dispersoids in AI-TM (TM is a transition metal element) systems. It is considered that high melting point aluminides are formed by precipitation from the supersaturated aluminum matrix. The analysis is based on the fact that much higher content of TM than the solubility limit can be dissolved in alpha aluminum during the high energy ball milling. Nonetheless, the role of undissolved TM particles affecting the formation of aluminides is not suitably considered. In this paper, authors present experimental observation on the formation of Ab3Ti particles from mechanically alloyed AI-Ti alloys in the hyper-peritectic region. This study showed that, in the mechanically alloyed AI-20wt%Ti specimen, intermediate phase of cubic Ab3Ti and tetragonal AIz4Tis formed at 300 - 400°C and 400 - 500°C, respectively, before the MA-state reaches to the global equilibrium at higher temperatures. The formation behavior of Lh- Ab3Ti is interpreted by interdiffusion of Al and Ti in solid state based on the fact that large amount of nano-sized Ti particles exist in the milled powder. Present analysis indicated undissolved Ti particles of nanosize should have played an important role initiating the formation of Ab3Ti phase during annealing.IntroductionInterest in the hyper-peritectic AI-Ti alloys is based on industrial demand for high-modulus and high-temperature aluminum alloys. Earlier works on hyper-peritectic AI-Ti alloys with 4 to 12wt%Ti show that these alloys are strong at ambient temperature and maintain high strength above 300°C when titanium-trialuminide (e.g., Ab3Ti) is finely distributed in the aluminum matrix [1,2]. High melting point and high stiffness with low density of AbTi make the AI-Ti alloys strong with greater thermal stability while keeping weight savings as much as possible. Titanium in aluminum shares other merits of transition metal additions because Ti solubility in Al is low (i.e., 1.l5wt%Ti at 665°C and virtually zero below 400°C), and fine dispersion of Ab3Ti particles is readily accomplished and resists grain coarsening effectively."

Jan 1, 1996

By P. Aguirre

Recovery of zinc, copper and nickel from electroplating waste solutions was achieved 'by using a Pulsated Percolated Porous Electrode "3PE" reactor on a pilot plant scale. Intensity - potential curves were used to study the possibility of metal removal and to define the working potential range. The present study describes the use of the 3PE reactors in several electroplating industrial units for the decontamination of their effluents. These effluents were issued from different industrial solutions such as cyanide, sulfate, chloride and Watts baths. Using the stripping curves, deposition rates and electrical efficiencies were determined as function of the metal concentrations in these effluents. Their decontamination could be achieved to the level of few ppm of metals with reasonable current efficiencies. The recovery rates of zinc and copper were about 93 and 99 %, respectively. The. treated effluents contained less than 7 and 1 % of the initial contents of Zn and Cu, respec¬tively. This process allows the recycling of the recovered metals and leads to water saving.

Feb 13, 2014

By Vanessa M. Torres

Cia. Vale do Rio Doce is currently developing Niquel do Vermelho Project. The laterite deposit is located at Carajas Mineral Province at less than 15 km from Sossego Copper Project, scheduled for start-up in 2004. The available infrastructure, includes paved roads, large capacity railroad and port complex owned by CVRD, power supply and good quality water. The project was evaluated in the past for ferronickel production. In the late 1990s, CVRD switched its attention to investigating the usage of pressure acid leaching. The combination of good metallurgical behaviour for pressure acid leach (PAL) process route with reasonable mineable grades, and existing infrastructure justified the start of engineering studies in 2002. The project approach at the engineering phase is based on the dual objective of minimizing risks while maximizing project profitability and value. CVRD is currently completing the Niquel do Vermelho prefeasibility study. This paper outlines the main outcomes of the study and future perspectives for the project.

Jan 1, 2004

By S. Malinov, J. J. McKeown, W. Sha, S. McShane

"A model is developed for prediction of fatigue stress life S-N diagrams for Ti-6Al-4V alloy at different conditions, using Artificial Neural Network (ANN). Different factors which have influence on the S-N diagram are involved as input parameters of the NN, namely microstructure, environment, texture, test/work temperature, surface treatment and stress amplitude. As the output the S-N fatigue diagram is simulated and plotted.The model is based on standard multilayer feedforward neural network. The NN is trained with a comprehensive data set collected from the literature, using Levenberg-Marquardt training algorithm in combination with Bayesian regularisation. A very good performance of the trained Neural Network is achieved. Good correspondence between ANN"" prediction and experimental S-N diagrams is observed. Using the model S-N diagrams for different conditions are predicted and analysed. Graphical User Interface is developed for use of the model. We believe that the model will be important for practical applications in solving various problems on fatigue behaviour of the titanium alloy.IntroductionTitanium and its alloys have an increasing range of applications due to their very good combination of mechanical properties, corrosion and erosion resistance. They are currently finding widespread applications in many industries due to their desirable and versatile properties. Most important among the alloys is Ti-6AI-4Y. Jet aircraft manufacturers are the principal 'consumers of Ti-6Al-4V and it is often specified for critical parts, the failure of which could result in the loss of an entire system. A generic class of Ti-6AI-4V has been developed over the past years and it has become the best understood of all the titanium alloys. The advantages of titanium alloys include: (i) low densities, giving very attractive strength to weight ratios allowing lighter and stronger structures; (ii) superior corrosion and erosion resistance in many environments; (iii) high temperature capability. Although the titanium materials are still considered as expensive materials, for many applications the cost of titanium alloys can be justified on the basis of their desirable properties."

Jan 1, 2001

By J. T. Stanley

The identification of crystal phases and crystal chemistry can be critical to understanding the mechanisms of waste material interaction with native soils. Understanding these mechanisms can suggest correct methods for remediation and treatment. A program is outlined and examples are given of the development of effective techniques for rapid phase identification of environmental samples using electron microscopy. The program concentrates on the development of integrated object oriented software to aid rapid searching of online databases and rapid simulation of potential crystal diffraction patterns. Examples come from dried sludge taken from a former hard-chrome plating facility.

Jan 1, 1993

By Reimers. Jan H.

Practically all the world's lead is produced by sintering and blast furnace smelting, or the Imperial Smelting Process which is a variant of the blast furnace process. Increased coke and labour costs and strict lead emission limits have, however, made blast furnace smelting undesirable in most countries. A change-over to other lead smelting processes providing better working conditions and lower emissions is, therefore,. expected to occur once economic conditions improve and the necessary capital expenditures can be justified. The need for new lead smelting processes has long been evident and a number of new processes have been proposed 'and advanced to various stages of development. One of the new processes is already proven on commercial scale, while several others are still being tested on pilot plant scale.

Jan 1, 1983

By C. Beckermann

"A diffuse interface model is derived for the direct simulation of two-phase flows with surface tension, density differences between the phases, and phase change. The derivation starts from the balance equations for a sharp interface and uses a formal averaging procedure on an atomic scale to obtain diffuse interface versions of the equations. Two approaches are considered: (i) the two phases have different velocities inside the interface and separate conservation equations are solved for each phase, and (ii) the two phases have the same velocity inside the diffuse interfuce and mixture conservation equations are solved. Based on a superposition of microscopic (atomic-scale) and macroscopic interface morphologies, an expression for the interfacial momentum source term is introduced that models surface tension effects and accounts for immiscibility between the phases.IntroductionDiffuse interface methods have been a popular tool in the direct simulation of two-phase flows [I]. In diffuse interface approaches, the interface between the two phases is characterized by a rapid but smooth transition in the properties, such as density and viscosity. Usually, a phase function ? is introduced to represent this transition, and the evolution of ? in the domain is computed from a separate equation or recipe. A unique set of conservation equations (e.g., mass and momentum) is solved on the entire domain, irrespective of the phase present, by accounting for the transition in the properties and introducing terms that account for interfacial sources. The continuum surface force (CSF) model of Brackbill et al. [2], which accounts for surface tension, is an example of the latter. The volume-of-fluid (VOF), level set, and phase-field methods are all examples of diffuse interface approaches. The major advantage of diffuse interface methods is that explicit tracking of the interface and the application of traditional sharp interface conditions are avoided. A disadvantage can arise from the artificial smearing of what is in reality an interface of atomic-scale width; however, techniques have been developed to overcome this problem."

Jan 1, 2004

By Douglas J. Harvey, Chi-Mou Ni

"This paper presents an analysis technique for the solidification of metal castings. This method, based on a modified finite difference scheme with an irregular mesh, is capable of dealing with the complex geometries of castings. The nonlinearities in material properties of specific heat and thermal conductivity, arising from the phase change during solidification, are accounted for in the step-by-step calculations. Two solidification problems are solved with this analysis technique and the calculated results compare satisfactorily with experimental data. IntroductionCasting process design engineers are often faced with the difficult problem of designing castings to be produced porosity-free. Since the solidification of metal is affected by many interacting variables such as the thermal conductivity, density, and specific heat of both the molten metal and the mold, it is easily seen why this is a difficult task.Typically, casting tooling design is an intuitive process which builds on past successful methods. After processing equipment is constructed, trial castings are made and examined for dimensions and integrity. Changes in the tooling are generally required to improve casting soundness or to reduce cycle time. In the permanent mold process, tooling is complex and difficult to alter after initial construction. The water-cooled steel molds are part of the complete automated system. Associated holding furnaces, pouring ladles, casting conveyers, and utility connections all make other than minor adjustments a costly and time consuming task. An analytical method for using the principles of heat transfer for predicting solidification patterns would be of great value in the permanent mold process by minimizing costly changes."

Jan 1, 1986

By Peter K. Eriksson

Nanofiltration is very efficient in separating heavy metals from water solutions, even if they contain strong acids. Desalination System, Inc., has many years of experience in this area, and this paper deals with three different such cases. The first case deals with concentrating the heavy metals in the pregnant leach solution from a copper dump leaching site with a surplus water problem. The increased copper concentration in the pregnant leach solution increases the capacity of the following copper extraction stage. The nanofIltration permeate is polished with a biomass adsorption column to remove the small amounts of remaining heavy metals, before being discharged. This method eliminates sludge handling and disposal, which are quite costly with the alternative precipitation process. In the second case, a complicated precipitation method was used to remove heavy metals from the waste stream of a specialty metals manufacturer. Nanofiltration was installed to increase the metals concentration four times, which greatly simplified the precipitation process. The chemical consumption and sludge production decreased by more than 80 percent, and the labor cost decreased by 66 percent. In the third case, nanofiltration was used to purify waste sulfuric acid solutions containing heavy metals, to meet the specifications for technical grade acid. Sulfuric acid concentrations above 30 weight percent were successfully purified in a multiple pass membrane system.

Jan 1, 1996

By J. Boitano

This paper discusses the study, design and implementation of the new gas handling system for the Caletones Smelter of Cbdelco..Chile. A discussion on design conditions for a Mure Sulphuric Acid Plant using Teniente Converter.gases.is also included. The old system which started to be modified in 1985 and relied on natural draft and used balloon flues, resulted in a limited .gas handling capacity for operation under Mure process conditions. This system also caused excessive fugitive gases in the smelter working areas. The new system permits handling of process gases from the higher capacity Teniente converters installed in 1987-1989 Improving the gas handling of the reverberatory furnaces and Peirce-Smith converters as well as the environmental conditions of the smelter. This system utilises improved converter gas hoods, evaporative cooling and electrostatic precipitators gas cleaning, and is based on natural draft.

Jan 1, 1992

By Satoshi Itoh

Phase equilibria and activities of the components in the liquid lead-antimony-oxygen ternary system, which is of fundamental importance for discussing the' recovery of lead and antimony from a used lead-battery, have been investigated at 1173 and 1223 K. The two liquid phases of metal and oxide were observed at the temperatures studied, and the tie lines indicating isoactivities were determined. The activities of PbO, SbO1.5 and Sb2O3) in the PbO-SbO1.5 and PbO-Sb2O3 pseudo-binary systems were then obtained by applying the Gibbs-Duhem equation to the phase relation of metal-oxide equilibrium. Both in the pseudo-binary systems the activities exhibit negative deviations from Raoult's law. The vapor pressures of lead, antimony and lead oxide, antimony oxide were calculated by using the activities of the components in the lead-antimony-oxygen ternary system. As a result, an oxidation of antimony concentrated in an anode slime followed by evaporation as antimony oxide Sb406 was found to be considerably effective for the recovery of lead and antimony from a used lead-battery.

Jan 1, 2003