Search Documents

By A. Shemi

Tungsten carbide scrap (WC–Co) is material generated from the tungsten carbide manufacturing process and worn out or used carbide parts from industry. Tungsten (W) ores contain about 3 wt% WO3 and their W concentrates about 10– 75 wt% WO3. Tungsten carbide scrap typically contains 40–95 wt% W. The high intrinsic value of W and the fact that the least valuable scrap contains more W than the average tungsten ore makes tungsten carbide scrap a worthy material for re-use. This study has investigated the selective dissolution of the cobalt (Co) binder phase, and recovery of tungsten monocarbide (WC) and Co using an acid leach process. The Co component was selectively leached leaving the WC solid particles intact. Further investigation using a complexing agent-aided acid leach process that takes advantage of organic chelating agents that form a soluble tungsten complex in place of the passive insoluble tungsten oxide is envisaged. The optimal dissolution of the Co binder phase using an inorganic acid in conjunction with an organic complexing agent is a novel approach with the potential of reduced leaching times and possibility of regenerating the unreacted organic acid.

By Bingguo Liu, Daifu Huang, Jinhui Peng

"The conditions to prepare U3O8 by calcination from ammonium diuranate were optimized, and the response surface design method was applied to analyze the influence on the total uranium and U+4 of calcination temperature, calcination time and mass of sample. A quadratic equation model for the total uranium and U+4 of U3O8 was built and the effects of main factors and their corresponding relationships were obtained. The analysis of variance shows that calcination temperature and calcination time significantly affected the value of total uranium and U+4 of U3O8. The optimal calcination conditions were as follows: calcination temperature 931.83 K, calcination time 24.32 min and 43.89 g. Under these conditions the value of total uranium and U+4 of U3O8 was 84.78% and 28.02%, respectively. The validity of the model was confirmed experimentally and the results were satisfactory.IntroductionNuclear energy is clean, effective, and a sustainable from of energy. It plays an important role in overcoming the impending global energy crisis, and in reducing energy vulnerability. In addition, nuclear energy is a possible cheaper and cleaner source of energy compared to fossil fuels, with no not really, mining of uranium produces CO2 contribution to green house gases [1]. Uranium dioxide, one of the most important fuel pellets used as nuclear fuel in light water reactors, is manufactured by calcining ammonium diuranate to triuranium octaoxide, followed by its reduction to uranium dioxide using cracked ammonia at 700°C [2]. Earlier attempts to optimize the important calcination process through several common techniques have not yielded desirable results [3]. These techniques either rely on the classical one parameter at a time approach that ignores the combined interactions between physicochemical parameters, or are theoretical in nature. Furthermore, these techniques also require large number of experimental data to be generated [4]. In order to produce triuranium octaoxide in an optimized manner, which considers the interaction of different process parameters [5], there is a need to adopt a multivariate statistical technique."

Jan 1, 2011

Four slag types covering the range of Fe-Ca-Si-O compositions and two iron blast furnace slags were melted at 1300 °C and doped with 1% of arsenic, antimony, cadmium, zinc and chromium. The melts were either slow cooled or quenched and the solidified slags were leached according to TCLP procedures. The morphology of the solidified slags was characterised using XRD, optical and electron microprobe techniques. Theoretical considerations showed that the capacity of the molten slag to hold the above toxic elements depended upon slag basicity and this was confirmed in practice. The experiments showed that the leaching of the toxic elements was a function of surface area and the phases present, both of which were affected by the mode of cooling. Iron silicate slags produced in nonferrous smelting operations and blast furnace slag from ferrous smelting operations both show promise of being suitable media for immobilising low levels of toxic elements and complying with current regulatory requirements.

Jan 1, 1994

By Huimin Lu, Neale R. Neelameggham, Guangzhi Wu

In China’s Inner Mongolia Tuquan County, 1.4 billion tons of reserves of serpentine deposits were found. Because serpentine belongs to magnesium silicate, there is no good reducing agent to reduce magnesium. In the local there is also a large reserves of high-aluminum bituminous coal for thermal power, power plants each year produce a large number of high-aluminum fly ash. The aluminum-silicon alloys obtained from this high-aluminum fly ash as the raw material by carbothermal reduction method can reduce the magnesium from the serpentine. In this paper, first, the feasibility of producing aluminum-silicon alloys by carbothermal reduction of high-alumina fly ash was studied, the hypereutectic aluminum-silicon alloys were obtained; and then the investigation on aluminum-silicon alloy as a reducing agent to reduce of metal magnesium from serpentine was carried out. According to the previous investigation, the optimized technical process for the extraction of metal magnesium from serpentine was proposed.

Mar 1, 2018

By Ben Hogg

Since the development of the top-submerged lance (TSL) technology for copper and lead smelting by the cooperation of Mount Isa Mines (MIM), now owned by Glencore, and the Commonwealth Scientific Industrial Research Organisation (CSIRO) the core of the ISASMELT™technology has always resided in the lance system. Through continuous innovation and operation of our own smelters, first at MIM, subsequently at Mopani, and also at both the Kazzinc Copper and Kazzinc Lead smelters, Glencore Technology have expanded the core equipment supply to enhance the plant operability. The success of Glencore Technology’s expertise can be directly measured by the success of the Kansanshi Copper Smelter plant, which achieved 100% nameplate capacity within three months of start-up. This paper describes the ISASMELT™ core equipment and how it is applied to smelt sulfide materials. It highlights the strength of the ISASMELT™: continuous innovation to facilitate the versatility and continued increased capacity with every plant implementation.

By Susumu Imashuku

A pseudoternary phase diagram of the BaO?ZrO2?ScO1.5 system is established and the conductivities of the scandium-doped barium zirconate are measured in wet conditions. According to the phase diagram, the molar fraction of scandia in the barium zirconate phase that equilibrates with the cubic zirconia (ZrO2) and scandia (Sc2O3) phase is 0.03. On the composition line, where the molar fraction of barium oxide (BaO) is 0.50, the solubility of scandia into barium zirconate is 0.27 as a molar fraction of scandia. At around 500 °C, the conductivities of scandium-doped barium zirconate are estimated to be almost same as that of yttrium-doped barium zirconateThe activation energies for bulk proton conduction in scandium-doped barium zirconate (0.57 eV for BaZr0.90Sc0.10O3-d) are higher than that of yttrium-doped barium zirconate (0.44 eV for BaZr0.90Y0.10O3-d). In addition, the bulk conductivity of scandium-doped barium zirconate in this study is 10 times higher than the reported conductivities in the temperature range of 75 °C to 300 °C.

Jan 1, 2006

By Adam C. Powell

A new Cahn-Hilliard phase field model of transport-limited electrochemistry describes phase boundary motion due to oxidation and reduction reactions at metal-electrolyte interfaces. Benchmarks demonstrating the accuracy of the method include open circuit voltage and closed circuit current in metallothermic reduction, and linear stability theory in metal electrolysis, including a new stability criterion for reduction of liquid metal from liquid electrolyte. The model is applied here to understanding cathode interface stability in titanium electrolysis e.g. in the SOM process developed with Uday Pal, and to structure evolution in subhalide reduction of titanium dichloride by magnesium developed by Toru Okabe. Potential for application to new fuel cell and battery systems is also discussed.

Jan 1, 2006

By Masaru Imaizumi, Hiroyuki Nomura, Mitsuharu Takita

"Cast iron possesses many superior characteristics caused from precipitated graphite structure, for example, castability, wear resistance, solid lubrication, damping capacity. But the more graphite hyper-eutectic cast iron contains, the lower its mechanical strength becomes, because graphite gives a negative effect to strength of cast iron. In addition, primary graphite tends to segregate during solidification, so uniform materials are difficult to be produced.In this study, authors introduced semi-solid processing in developing new and high quality cast iron. A series of semi-solid processing experiments were carried out to clarify the effect of stirring condition; solidification temperature and etc. on microstructures and characteristics of cast iron. In particular much attention is paid to the appearance of ternary eutectic zone at the final stage of solidification. As the results advanced hyper-eutectic cast iron was obtained with high quality of both the mechanical strength and wear resistance. As for the mechanical strength, 300MPa and 0.60% are obtained as the tensile strength and the elongation values, respectively, under the controlled stirring condition. This indicates that semi-solid processed hyper-eutectic cast iron is used prospectively without spheroidization.IntroductionCast iron has various good properties such as wear resistance, solid lubrication, damping capacity and machinability. The characteristics of cast iron are mainly decided by graphite structure, namely graphite shape and its distribution in the matrix. Mechanical strength of cast iron is large in the case of small quantity of graphite particles which are precipitated uniformly, however, it becomes small in the case of large quantity of graphite precipitated flakily."

Jan 1, 2000

By Hidefusa Takahara, Koichi Miyake, Dierk Raabe

"Mechanical properties of copper wires were examined. The copper wires containing 5-10 mass % chromium and 1-3 mass % silver were produced through heavily cold deformation. It was expected that the copper wire was easily fractured during cold deformation because of the existence of brittle chromium phase in the alloy. In fact, the copper wire was fractured due to large work hardening, when the true strain [n] exceeded 5. However, the copper wire annealed at 1273K for 6 ks ·in the middle of deformation process could be smoothly drawn to 11=8. After precipitation treatment for silver phase at 473k for 1.8 ks, the wire was able to further drawn to n=8.4. The final deformed wire showed tensile strength higher than 1200MPa.IntroductionDownsizing of electronic devices has led to the demand of finer and higher strength materials for cables. Conventional copper alloys have about 800MPa in ultimate tensile strength. These strength are mainly obtained by precipitation hardening. Nowadays, a process for higher strength wire has been developed, where dual phase copper alloy is used. When it is drawn heavily, the' second phase is elongated along drawing direction and the wire gets high strength due to fiber reinforcement (1). That alloy is so called in-situ formed fiber reinforced ·alloy. Cu-Ag(2), Cu-Nb(3) and Cu-Cr(4) systems are well known as such alloys. It is also well known that chromium is brittle material except single crystal and high purity of chromium. However, Mihara et al. C5l have achieved 1 GPa in ultimate tensile strength in the Cu-Cr-Zr and Cu-Cr-Ti alloys by appropriate thermo-mechanical processing.In this study, the Cu-Cr-Ag systems were investigated: The alloys contained 10 or 5% chromium and 3 or 1 % silver. It was demonstrated that silver precipitated in copper matrix contributed on further hardening."

Jan 1, 2000

By Yilin Fang, Alain Bonneville, Timothy. D. Scheibe, Zhijie Xu

"We present a hydro-mechanical model for geological sequestration of carbon dioxide. The model considers the poroelastic effects by taking into account the coupling between the geomechanical response and the fluid flow in greater detail. The simplified hydro-mechanical model includes the geomechanical part that relies on the linear elasticity, while the fluid flow is based on the Darcy's law. Two parts were coupled using the standard linear poroelasticity. Analytical solutions for pressure field were obtained for a typical geological sequestration scenario. The model predicts the temporal and spatial variation of pressure field and effects of permeability and elastic modulus of formation on the fluid pressure distribution.IntroductionIn order to achieve a substantial reduction of CO2 emissions and alleviate the atmospheric carbon problem, massive scale carbon sequestration is required involving millions of tons of carbon dioxide injection over several decades. The geomechanical response is important upon the injection of substantial supercritical carbon dioxide into deep geological formations. Supercritical CO2 is less dense than brine waters and the buoyancy driven flow of CO2 requires the aquifer to be capped by low permeability rock (""caprock"") to prevent the upward migration of C02 (as shown in Fig.1 ). Massive scale injection of C02 changes the overall stress state in the caprock and formation. This change leads to large deformation that can damage the caprock, create fractures, and open new flow paths for supercritical C02. Therefore, a coupled hydromechanical model becomes essential for the caprock integrity analysis."

Jan 1, 2012

By José R. de Tenorio

The aim of the present work was to investigate the reduction process of MnO~FeO-Si02 slags by carbon-saturated liquid iron. The effect of the initial Mn content in the bath was explored. The initial Mn content was in the range of 0 up to 40 wt. %. The MnO content in the slag was kept constant at 40 wt. %. Tests were performed in laboratory apparatus. Samples of slags and bath were taken. In the first 5 minutes, it was observed a very strong reduction of FeO. This first step promoted a MnO-Si02 enrichment of the slag and a formation of CO bubbles, which increases the slag level. The increase ofMn content decreases the MnO reduction rate.

Jan 1, 1996

By Yuzhe Zhang, Matthew Andriese, Jiann-Yang Hwang, Guanghui Li, Zhiwei Peng, Tao Jiang

The microwave power absorption characteristics of iron oxides, including Fe2O3, Fe3O4 and Fe0.925O, have been studied by determining dielectric loss and magnetic loss distributions in 0.05-m-thick oxide slabs irradiated with 1.2-kW, 2.45-GHz microwaves. The results reveal that the dielectric loss is the main factor contributing to microwave absorption in Fe2O3 and Fe0.925O, while the magnetic loss dominates the power absorption in Fe3O4 below its Curie point. Uneven power distributions are observed in the slabs and this phenomenon becomes even worse at high temperatures at which the permittivity increases significantly. Quantification of power absorption in the oxides is of great importance for efficient and uniform microwave heating

Jan 1, 2015

By Nobuhiro Oguma, Yuji Mizuta, Hideya Sato, Shigehiko Iwahori

"Recyclable materials containing copper and precious metals have been treated at the Mitsubishi Process in Naoshima. In 2003, a new incinerating and melting plant (pre-treatment plant) for waste materials, such as shredder residue of automobile and scrapped appliance, was constructed. All of produced slag/metal mixture is treated at the Mitsubishi Process, and which results in the significant increase of recyclable materials treatment. The combination of two processes has realized a highly efficient and environmentally friendly system for recycling valuable metals in the waste which used to be sent to a landfill. Naoshima continues to make efforts to achieve the highly efficient operations of the two processes, and plans to increase the treatment of recyclable materials further. This paper summarizes the recent operations and the various improvements implemented in the pre-treatment plant.IntroductionRecyclable materials containing valuable metals such as copper and precious metals have been treated at the Mitsubishi Continuous Copper Smelting and Converting Process (Mitsubishi Process) since the start-up in 1991. In the early stages, recyclable materials consisting mainly of metal scrap were charged into the process and the treatment had been increased steadily. In order to promote the recycling business, treatment of various kinds of materials including printed circuit boards was started. However, the treatment hit the ceiling due to a limitation of furnace boiler capacity, since they contained large amounts of combustible materials. In addition, severe corrosion of boiler tubes was caused by halogen contained in recyclable materials."

Jan 1, 2012

By Zhiqiang Zhou, Libin Zhu, Zizong Zhu, Hao Xiong, Yuchuan Ding

In order to utilize the lean ore resources from XinJiang rationally and optimize mixture, laborarory measurements have been carried out under different basicity, various mixed carbon content as well as the properties (ratio) of fuel particle size by the sintering pot for further microstructure analyses. The results show that sinter strength falls by 5.0%, low temperature reduction disintegration index (RDI) drops off to the lowest in certain ranges. The natural degradation index of sinter is much higher when sinter basicity is between 1.65 and 1.75. The sinter strength increases when sinter basicity is between 1.75 and 2.0. Meanwhile, the sinter strength and RDI +3.15 improve with increasing carbon content. And the sinter strength and RDI+3.15 both decrease with the decrease of the distribution ratio of small fuel particle, thereby decreases the yield of sinter. Microstructural analyses have been investigated to figure out the mechanism of the influence of the three factors on sinter.

Mar 1, 2017

By D. M. Wyslouzil

The fundamentals of dissolving silver and silver minerals are discussed in the following sections: 1) Basic chemical reactions in the silver system 2) Leaching of pure silver minerals 3) Leaching of silver-bearing ores 4) Description of processes The basic chemical reactions of silver are an important guide to the mineral processor or the extractive metallurgist, particularly for systems in which complex formations are balanced against solubilities. The competition of other cations for free ligands can shift the equilibrium to the detriment of silver. Solubilities of pure silver minerals in specific solvents may not be a good indication of the solubility of silver minerals in ores. The abundance of silver minerals which usually appear in a typical ore precludes the selection of a single method that would result in the best extraction of silver from all minerals in the ore. Frequently, the recovery of silver from host minerals requires a destructive pretreatment such as intensive leaching, oxidation with or without elevated temperature and oxygen pressure, or roasting. The transformation of the host or the silver minerals does not always result in a leachable species? and this requires additional treatment before the precious metal can be recovered.

Jan 1, 1990

By Hang Goo Kim

A computer simulation has been carried out to predict the distribution behavior of minor elements such as Pb. Zn, Bi, Sb and As in recently proposed copper smelting and converting processes with submerged oxygen injection in which tonnage oxygen is used with a shielding gas. In this study the technique of stepwise equilibrium modeling was employed and some of the thermodynamic data were updated or reassessed. The volatilization and slagging of undesirable elements were investigated in copper smelting (steady-state) system, copper matte converting (batch) system, and the combined (smelting + converting) system at extremly high oxygen-enrichment levels. The predicted minor-element behavior under high oxygen- enrichment was compared with that in the Noranda process (normally 42% oxygen-enrichment in smelting and 24% in converting) and the reverberatory process using air. The effects of various operating parameters such as temperature, the final matte grade in smelting, the initial matte grade in converting and the O/Fe ratio in slag on the behavior of minor elements are discussed.

Jan 1, 1991

By Tina Maniatis

Applied Biosciences has developed a biological technology for removal of arsenic, nitrate, selenium, and other metals from mining and industrial waste waters.The ABMet® technology was implemented at a closed gold mine site in Canada for removing arsenic from tailings pond water. The system included six bioreactors that began treating water in the spring of 2004. Design criteria incorporated a maximum flow of 567 L/min (150 gallons per minute) and water temperatures ranging from 10°C to 15°C. Influent arsenic concentrations range from 0.5 mg/L to 1.5 mg/L. The ABMet® technology consistently removes arsenic to below detection limits (0.02 mg/L). Data from the full scale system will be presented, as well as regulatory requirements and site specific challenges. Keywords: Arsenic, Sulfate Reduction, Metal Sulfide Precipitate, Biological Water Treatment

Jan 1, 2005

By Wankun Wang, Fuchun Wang

Based on the study of artificial neural network, the neural model was established for the prediction of germanium extraction from zinc oxide dust by microwave alkaline roasting-water leaching. Alkali-material mass ratio, microwave heating temperature, liquid-solid ratio, aging time, leaching time and leaching temperature were the significant factors for the process. The results indicated that the neural network prediction model was reliable, and the forecast values fitted well with the actual experimental values. The model could be used to predict the regeneration experiments with high credibility and practical significance. The accuracy of convergence of the model reached 10−5.

Mar 1, 2018

By Shengli Wu, Yuandong Pei, Zhixing Zhao, Shuhai Ou, Jiangshan Shi, Huaiying Ma, Jun Xiong

Spraying technology on sintering surface bed after ignition has become a hot research topic, with the purpose of achieving energy-saving, emission reduction and improvement of sintering indexes. In this paper spraying steam technology was researched from theory, experiment and practice. First of all, from the thermody- namic and kinetic analysis, the mechanism of sintering surface spraying steam was analyzed and its advantageous effect was con firmed. Based on this, sintering pot test and commercial trial were carried out respectively. The results shown that spraying steam is bene ficial for increasing coke combustion ef ficiency with improving CO 2/(CO+CO2) in the exhaust gas from 80% to about 85% level, through decreasing CO content of flue gas by more than 1000 –2000 ppm. There was a suitable spraying amount to improve the quality of the sinter, and the spraying position of the steam cannot be excessively front and rear. Due to the low steam pressure (1 kg) and temperature (about 100 °C) compared with industrial steam (3 kg and 130 °C, respectively), the sinter quality such as yield index was affected by spraying steam in sintering pot test to a certain extent, and proper spraying amount (0.008 m 3, 50 kg sinter) in sinter pot test is far smaller than application amount in commercial trial (2t/h). It is thought that suitable spraying steam parameters has a comprehensive effect of energy saving and quality improvement.

Mar 1, 2018

By Peter Woodall, Paul Telford, Pengfu Tan

"Arsenic enters the Mount Isa copper circuit in the form of arsenic rich minerals in concentrates from both the Mount Isa and Ernest Henry copper mines. Arsenic is a volatile metal, and will partition in the copper smelter between smelter off gases, slag and anode. Most of the volatile arsenic will report to Isasmelt Electrostatic Precipitator (ESP) or Waste Heat Boiler dusts where it will form a re-circulating load within the smelter. ESP dust is produced at a rate of 15,000 - 20,000 t/y and is currently removed from the precipitator and leached in the new ESP Dust Recovery Plant to separate copper and arsenic from the ESP dust. This paper describes the laboratory test works of ESP dust leaching, neutralisation and cementation processes. The planttrial, commissioning and operation have been presented as well.1. IntroductionThe flue dusts generated in the process of copper smelting contain appreciable amounts of copper and other valuable metals including precious metals. These flue dusts also contain appreciable amounts of arsenic trioxide where arsenic occurs in the ore body. The copper smelters processing concentrates generate residuals, such as ESP dust, containing arsenic trioxide. ESP dust contains impurities such as arsenic and bismuth which are harmful to the copper refining process if they report to anode. These impurities are fumed off in the smelting process and report to the dust as arsenic and bismuth oxides.The content of arsenic in the feed of Mount Isa copper smelter is about 0.1 % to 0.4%. Arsenic is a volatile metal, and will partition in the copper smelter between off gases and anode. Most of the volatile arsenic reports to Electrostatic Precipitator (ESP) and Waste Heat Boiler dusts where it will form a re-circulating load within Mount Isa Copper Smelter. Unless arsenic is bled from the smelter circuit, it will build up to a point where both anode quality and smelter hygiene are adversely impacted."

Jan 1, 2011