Search Documents

By Susanne Pignolet-Brandom

Fourteen samples of crushed Duluth Complex rock were characterized by the QEM?SEM automated scanning electron microscope image analysis system to evaluate the application of the system to mining waste rock characterization. The system can reliably distinguish the iron sulfides, the copper-iron sulfides and the nickel-iron sulfides. Calcite was distinguished from all other minerals except fluorite. The volumetric abundances were verified by comparing elemental abundances calculated using the QEM"SEM volumetric percentages and appropriate mineral compositions with elemental abundances determined by standard laboratory procedure. The pH and sulfate concentrations of rinse water from laboratory leach experiments correlated well with the mineralogical data.

Jan 1, 1989

By Kiyoshi Shibata

A new assessment model has been proposed for metal production and its recycling system. The model consists of three processes, smelting of ore, cascading and upgrading of metal scrap. The present approach is to assess the total energy consumption of the system, by introducing two equations for describing the relationships between critical impurity content and the mass of production or scrap recycling. The total energy consumption in the system can be described as a function of recycling rate and performance of the upgrading process. The present model suggests that the impurity removal efficiency and yield in the upgrading process are essential to reduce the energy consumption in the systems. Especially, such points should be explicitly controlled in recycling of aluminum. The potential capability of this model was also discussed by obtaining several quantitative information required for the process design and the operational control of beneficial recycling of metals.

Jan 1, 1998

By J. C. Huyhua

The effect or various oxidants on gold and silver dissolution in thiourea solutions (0.05 M in H2SO4) was studied using the rotating disc technique, a.t 2s c and 600 rpm. These studies were carried out at constant (4:1) initial molar ratio or thiourea to oxidant concentrations, to produce 50 % thiourea. oxidation. The initial dissolution rate of gold was approximately four times higher in the presence. of ferric sulfate (5.37 x 10-3mg cm-2 s-1) than in the presence of hydrogen peroxide (H2O2), potassium persultate (K2S2O3), or monopersulfa.te (KHS06). The dissolution rates for silver were considerably lower than gold for the same oxidants. Oxidation of thiourea in the presence of peroxygen and persulta.te compounds is a. fast reaction and it is completed in less than ten minutes. On the other hand, the oxidation or thiourea with? ferric.sulfate is slow, yielding a second-order reaction rate constant k = 6.09 I mol-1 h-1. Sulfur formation in the ferric thiourea system begins when ferric ion reduction approaches to completion. With hydrogen peroxide, sulfur is observed at lower thiourea concentration than ferric. Suifate. The presence of a large excess or free thiourea i.e., s to 20 % thiourea oxidation) retards sulfur formation and maintains favorable dissolution rates. Finally, carbon-in-leach experiments indicate that thiourea solutions a.re stable for several days, with ferric sulfate or hydrogen peroxide. The dissolution rates of gold and silver doubles in the presence or activated carbon when hydrogen peroxide is used as oxidant.

Jan 1, 1989

By F. L. Marley

Small and medium-sized flotation plants with no assaying instrumentation still depend much upon the art of the operator to produce acceptable and consistent results. Improved performance can be accomplished by the use of the simple microscope set up as a control device. The visual recognition of products in the circuit does much to eliminate uncertain shift operating decisions and is an easy technique to acquire. Mineral staining methods further assist in the determination of components within the mill products. Simple mounting upon scotch tape and other adhesives is rapid and convenient. The microscope also has a practical role for the plant metallurgist or laboratory technician when evaluating middling products, and their routing within the circuit. Examples are reviewed where the microscope has been used for operational control in both sulfide and nonmetallic mineral flotation plants.

Jan 1, 1981

By Neng-Wen Yu, Miao Wang, Ji-He Wei

The mass transfer characteristic between powder particles and liquid steel in the RH-PTB (Powder Top Blowing) refining has been investigated in a water model of 1/5 scale for a 90t RH degasser. The sodium chloride powder with analytical purity has been used as the flux for blowing. The mass transfer coefficient of the liquid side has been determined under the conditions of RH-PTB process. The influences of the main technological and structural parameters on the mass transfer rate have been examined. The results indicated that under the conditions of the present work, the mass transfer coefficient on the liquid side increases with raising the lifting gas blowing rate, inner diameter of the up-snorkel, circulation rate of the liquid and particle size of powder flux. And it decreases with an increase in the inner diameter of the down-snorkel. It is in the range of (l.36-7.30) x 10·4 mis, the appropriate dimensionless relationships have been obtained as follows:

Jan 1, 2000

By A. S. Usmani

The flow associated with the pouring of molten metal into moulds has been modelled on the basis of certain simplifying assumptions. A finite element based Navier-Stokes equation solver has been used to analyse the flow. The velocities obtained from the Navier-Stokes equation solver are used to advect a pseudo-concentration function for modelling the fluid front. A simple problem with a known analytical solution is solved first to test the model. Subsequently, several more examples with varied geometrical configurations are modelled, including one with curved flow boundaries.

Jan 1, 1992

By Saynbaatar, Gangping Ma, Jianhua Fu, Qiqige, Jinghua Wang

The influence on the performance of foam concrete made by replacing cement with some industrial waste residues was researched in this paper. The result shows that the 7d and 28d compressive strength of foam concrete increases firstly and then decreases with the increasing amount of industrial waste residue. The proper added range is 10%-20% for steel slag, blast furnace slag and coal ash, but, 8% for desulfurized fly ash. With the proper adding ratio, the compressive strength of foam concrete always increased comparing with the pure cement foam concrete. When adding 48% of the compound industrial waste residues, the 28d compressive strength of the foam concrete reached the 2.9MPa which could match the pure cement foam concrete. The results indicates that there is a synergistic effect among the compound industrial waste residue, and this effect is benefit to improving the compressive strength of foam concrete.

Jan 1, 2015

By Asmo Vartiainen

Background of Direct-to-Blister Flash Smelting is discussed; especially slag chemistry relating to copper solubility, slag fluidity and impurity behavior. In December, 2000, Mini-pilot Flash Smelting test runs were carried out at Outokumpu Research Oy to produce blister copper from Chilean concentrate and white metal and from a mixture of them. Tested slag types were iron silicate slag, ferrous calcium silicate slag and calcium ferrite slag with different slag compositions and different concentrate/white metal ratios. The test runs were successful. The fluxing effect of copper oxide was clearly demonstrated and ferrous calcium silicate slags remained fluid on a very wide liquidus range. The distribution of arsenic between ferrous calcium silicate slag and blister copper is much higher than between iron silicate slag and blister copper. This successful test run with the new slag type offer new possibilities in Direct-to-Blister process design.

Jan 1, 2003

By R. P. King

The central idea presented in this paper is straight forward. Some fairly obscure mathematical techniques are presented from the fields of integral geometry and stereology and these techniques are shown to provide workable quantitative relationships from which the liberation spectrum of an ore after comminution can be determined. The experimental data that is required can be obtained very accurately and conveniently by image analysis of polished sections of the original ore. This quantitative mineralogical analysis provides a bridge that can link the worlds of the mineralogist and the mineral process engineer. This paper has been written to introduce this quantitative approach to a wider audience in the hope that the approach will be used more widely and that the basic linear intercept analysis data will be measured for a wider range of mineralogical textures. This could lead to a more comprehensive characterization of typical mineral ores that will be of considerable use in practical mineral processing.

Jan 1, 1991

By Feng Liu, Bingji Yan, Zhiwen Shi, Hongwei Guo, Jianliang Zhang

During production of a large quantity of steel, slag is produced at the same time. This paper chooses blast furnace slag (BFS) as the main material for the research. The purpose of the research is to explore its optimal physicochemical properties and the use of BFS in building stone field. The paper elaborates the experimentation process of producing glass-ceramics and presents the results. The results show that SiO2 content in BFS and amount of Cr2O3 and Fe2O3 added as nucleating agents have certain effect on the properties of glass-ceramics. The results also show that the exothermic peak temperature of base glass is the lowest when adding 20% SiO2 to the BFS, and 2% Cr2O3 and 3% Fe2O3 as nucleating agents, which makes easy crystallization and optimal properties of the glass-ceramics.

Jan 1, 2015

By D. Gu, R. G. Anthony, C. V. Philip, M. E. Huckman

"In this paper, we review the equations needed to construct an ion exchange column model. These models contain three major components: 1) a differential material balance around the column, 2) a differential material balance around an ion exchange particle, and 3) a constitutive equation for diffusive flux. We then examine the ability of a fairly simple mathematical model to predict ion exchange column experimental data. This model contains the traditional absorption theory equations and is used to predict the behavior of a column filled with a hydrous crystalline silico-titanate and which is removing trace amounts of Cs+ from a high pH, complex electrolyte solution. Finally, we propose replacing Fick's law with the Nemst-Planck equation as the constitutive equation for diffusive flux. We use a NemstPlanck type model to predict batch experimental data, then evaluate it by comparing it's ability to predict experimental data to that of a more traditional Fick's law type model. The data from this comparison suggests that the Nemst-Planck type model yields better results.IntroductionMillions of gallons of strongly basic, radioactive waste are currently stored in underground storage tanks at Hanford and Savannah River and several locations within the United States. Due to the limited life expectancy of the tanks, there is a pressing need to remediate these wastes. This need has prompted the recent development of new ion-exchange materials for removing radioactive elements from aqueous solutions. A novel material called TAM-5 has been developed jointly by Texas A&M University and Sandia National Laboratories. TAM- 5, a crystalline silico-titanate, is highly selective for Cs + in the complex electrolytic solutions typical of these wastes. It is stable in very basic solutions and in radioactive environments [1, 2 ,3]. In laboratory testing to determine the selectivity of various materials, TAM-5 was superior to other candidate ion exchangers [4, 5]. The selectivities were determined by measuring a distribution coefficient, Kd, which is defined as the concentration, gig or mmols/g of Cs in the solid phase divided by the concentration, mg/L or mmols/mL, of Cs in the liquid phase. The units of Kd are ml/g or L/kg. Table 1 shows Kd values for TAM-5 compared to 9 other candidate materials in a typical waste solution [6]."

Jan 1, 1996

By Asmo Vartiainen

Background of Direct-to-Blister Flash Smelting is discussed; especially slag chemistry relating to copper solubility, slag fluidity and impurity behavior. In December, 2000, Mini-pilot Flash Smelting test runs were carried out at Outokumpu Research Oy to produce blister copper from Chilean concentrate and white metal and from a mixture of them. Tested slag types were iron silicate slag, ferrous calcium silicate slag and calcium ferrite slag with different slag compositions and different concentrate/white metal ratios. The test runs were successful. The fluxing effect of copper oxide was clearly demonstrated and ferrous calcium silicate slags remained fluid on a very wide liquidus range. The distribution of arsenic between ferrous calcium silicate slag and blister copper is much higher than between iron silicate slag and blister copper. This successful test run with the new slag type offer new possibilities in Direct- to-Blister process design.

Jan 1, 2003

By A. E. Clark

Rare earth compounds are widely known as possessing many extraordinary magnetic properties. In this paper, we focus on the huge magnetically induced displacements (magnetostrictions) which characterize the compounds of terbium with iron (Terfenol). Materials prepared commercially by both free-standing-zone (FSZ) and modified Bridgman (MB) techniques have now become available in large sizes and shapes. Prior to the development of the Terfenol alloys, it was possible to achieve giant magnetostrictions only at cryogenic temperatures. In the cubic Laves phase TbFe2 compound, saturation strains exceed 3000 x 10-6 at room temperature and above. Large magnetization 'jumps' can occur, causing huge spontaneous magnetostrictions with small triggering magnetic fields.

Jan 1, 1992

By Mitsuhiro Ohtaki, Tetsuzo Arakawa, Fujio Murata

Refining of Zn from aluminum scrap melt by some vacuum distillation processes was studied to promote aluminum scrap recycling. Effects of distillation conditions, such as melt temperature, vacuum pressure and holding time, on Zn distillation behavior were investigated theoretically and experimentally by 0.3kg/ch scale vacuum resistance furnace. Three methods to increase the surface-area/volume ratio of liquid metal, such as gas atomizing, mechanical atomizing and mechanical stirring, were tested to increase the Zn distillation rate in 5kg/ch scale vacuum resistance-furnace. It was easy to lower the remaining Zn content to less than 0.1 wt% within one minute by mechanical stirring method. A water-model simulation experiment indicated that a significant agitation of the melt by stirring would be effective to increase the distillation rate. Continuous agitation vacuum distillation process (CA VP) has been designed and the pilot plant is now in construction.

Jan 1, 2000

By Ma Ying

The continuous directional solidification technique of five kinds of special ZA alloys with eutectic, peritectic and eutectoid transformation under the condition of continuous casting by heated mold was studied. The mechanism of surface defects appearing in ZA alloy line was discussed and the structure of some defects were analyzed by SEM. The results show that only when the fitting of various technique factors, pressure head, outlet temperature, pulling speed and cooling condition are reasonable under a certain range, can the ZA alloy smooth line be continuously pulled out. Unreasonable techniques will result in hot tear, rough surface, mush outlet, leaking and other defects. The shape and location of solid-liquid zone have an important influence on the formation of the above defects. When the solid-liquid zone is located in the mould outlet or inner mould, the surface of solidification will protrude into the inner mould. If the remaining liquid cannot counteract the solidification contraction, a rough surface will appear. If the solidification surface further into the mould, the ingot in the mould will have a great friction force when pulling and will form a hot tear. When the solid-liquid zone is moved out of mould, the solidification surface will turn into a plane, which easily results in leaking. A vibration or unstable operation will cause an ingot winding during pulling

Jan 1, 2003

By Roy J. M. van Lier

In industrial aqueous solutions, germanium generally occurs in trace amounts amid high concentrations of other metals, such as zinc, copper and iron. Separation of germanium from these metals as well as its isolation from gallium and indium pose a real challenge to the hydrometallurgist. After a brief discussion of the aqueous chemistry of germanium, this paper reviews the flowsheet of the Apex Mine in Utah. The Apex property was the only mine in the world to be operated primarily for production of gallium and germanium, but apparently closed due to great operating difficulties. Several process variants proposed for the treatment of the Apex ore, including bioleaching methods, are addressed. Following a more general description of the behavior of germanium in hydrometallurgical zinc processing streams, available technology for its recovery from aqueous solutions is summarized. Precipitation, solvent extraction, ion exchange, electrowinning, ion flotation and liquid-membrane separation are all outlined in terms of the aqueous chemistry of germanium. Finally, the production of high purity germanium dioxide and metal is briefly discussed

Jan 1, 1995

By Xuling Chen, Zhiyun Ji, Min Gan, Wenqi Li, Xiaohui Fan, Zhiyuan Yu

"Specularite and vanadium-titanomagnetite are difficult to granulate, and with the increase of their proportions, the permeability of sintering bed is deteriorated together with the combustion velocity of fuel for the shortage of air through the sintering bed, which can lower sintering speed and specific production capacity significantly. The biomass fuel has a higher combustion velocity than coke breeze, therefore the productivity of specularite and vanadium-titanomagnetite ore can be improved remarkably by replacing coke breeze partly with biomass fuel .The results showed that, when the proportion of biomass fuel replacing coke is 40%,the sintering speed and specific production capacity of 35% specularite were improved from 19.06mm/min, 1.33 t/(m2·h)to 21.45mm/min, 1.47 t/(m2·h),and that of 55% vanadium-titanomagnetite were improved from 17.23mm/min, 1.11 t/(m2·h)to 22.80mm/min, 1.44 t/(m2·h). As a conclusion, biomass fuel is effective to strengthen sintering of refractory iron ore.IntroductionThe iron and steel industry of our country has achieved significant development in the recent years. In 2010, the output of steel has reached to 0.627 billion tons. The increasing scale of iron and steel has led to rigorous domestic iron ore environment, and the reserves of hematite and magnetite that have superior sintering characteristics are on the decline with continually exploiting and utilizing [1]. Therefore, the RIO (refractory iron ores) SP (specularite) and VT (vanadium-titanomagnetite) have to be applied vastly. However, the quality of sinters can be deteriorated when utilizing RIO in high proportion due to their poor granulation and metallogenic performances [2, 3]. Generally, the ratio of SP is 3~5%,which should not exceed 10% in our country currently [4]. Though high rate of VT is adopted in PZH steel for a long time, the productivity is obviously low compared with normal sintering [5]."

Jan 1, 2012

By Mitsutaka Hino

The contents of gangue minerals, such as A1203, P205, crystalline water and so forth in the iron ore imported to Japan tend to increase year by year, Though the increments of such gangue contents are approximately 0.1-0.2 mass%, some problems for the blast furnace operation in ironmaking process have already been reported, In order to clarify the mechanism of harmful effect caused by the small increment of gangue minerals, mainly A1203, on the blast furnace operation, the dripping behavior of FetO-CaO-SiO2-AI2O3-MgO slag from the iron funnel, which simulated the micro-porosity in sinter ore, has been observed with the wide range of basicity, Al2O3, FetO and Mgo contents. The effect of MgO on the dripping behavior of slag has been summarized in this paper, It was found that the addition of 2mass% MgO resulted in large increase of hold-up on the most of the conditions. When FetO content was less than 20mass% and the basicity was lower than 0.8, MgO lowered the hold-up even if the slag contained 10mass% Al2O3. Every slag hold-up showed the minimum at the basicity of less than unity on the conditions of constant FetO and A1203 contents. This trend became remarkable when the slag contained 2 mass% MgO.

Jan 1, 2003

By Pengfu Tan

In order to understand and control the formation of dioxins and furans in iron ore sinter plants and to possibly avoid expensive end-of-pipe removal stages, thermodynamic calculations on the stability of PCDD/Fs have been combined with sinter process modeling by means of kinetic simulations and computational fluid dynamics. Three thermodynamic databases of PCDD/Fs, derived using the Group Additivity approach and two computational molecular modeling methods, MNDO and PM3, respectively, combined with the SGTE database have been used to model the PCDDIF formation and the PCDD/F isomer distributions in iron ore sintering. The results show very similar conditions for the PCDD/F formation using the different databases. Concerning the isomer distributions of toxic PCDD/Fs, the calculated data derived from the MNDO method showed optimum agreement with measured values from industrial furnaces. The thermodynamic calculations also proved that the isomer distributions found in combustion processes are equilibrium values, while the concentration ratio of PCDDs and PCDFs in the wind boxes does not represent an equilibrium state. A CFD model of iron ore sintering was developed including the kinetics of 15 relevant chemical reactions with the aim of describing the temperature fields and the gas flow patterns in the sintering bed. On the basis of these information and experimental observations reported in the literature possible pathways for the PCDD/F formation in sinter plants have been identified: PCDD/Fs are formed in the critical temperature region of 250 to 450°C below the combustion zone, are then carried downwards with the gas and condensed close to the bottom of the sinter bed. Transported to the discharge end with the solid mixture, they are again released into the gas phase when the flame front approaches the bottom. PCDD/Fs are also formed in the last wind boxes when the hot off-gases cool down and reach the critical temperature range. Consequently, methods to reduce the dioxin formation reactions are proposed including inhibitor addition to the sinter feed and off-gas quenching.

Jan 1, 2003

By A. Block-Bolten

Copper concentrates from northern Peru contain large amounts of arsenic and antimony in the form of sulfosalts like enargite, tennantite and tetrahedrite. These impurities affect up to 30% of Peruvian copper production. Under the sponsorship of the Instituto Geologico Minero y Metalurgico in Lima a project to separate copper from arsenic without pollution of the environment is being carried out at the National University of Trujillo in Peru. The U.N.T. process is unique in the respect of using .low melting salts as solvents, and sulfides of metals with high cation potential as destructors of the complex sulfosalt molecules. Laboratory scale experiments have given encouraging results but interesting and difficult problems developed on scale-up. The process is pyro-hydrometal-lurgical and under certain circumstances its economics are promising.

Jan 1, 1981