Search Documents

By Lu Lin, Yanping Bao, Xiang Li, Linzhu Wang, Xiaobai Yan

The results showed the microinclusions were mainly Al2O3 and sulfide inclusions from tapping to the beginning of LF refining. Al2O3 inclusions were modificated into calcium aluminates after calcium treatment. Lots of spherical calcium aluminates composite inclusions containing MgO, TiO2 and MnS were found after soft blowing and during tundish metallurgy and left in the slab which caused the defects of beam plates. Pure Al2O3 inclusions were observed again after soft blowing 8min. Average sulfur content in inclusions decreased because of the high desulfurization ability of refining slag. Average Ca/Al ratio value in inclusions increased during LF refinging because of the reduction of CaO in slag by carbon and it increased obviously during the process of soft blowing 8min because of the dissolusion of calcium wire.

Jan 1, 2015

By Kenneth N. Han

Ammonia has been found to be an effective leaching reagent for gold, silver and platinum group metals in the presence of appropriate oxidants. Electrochemical and kinetic aspects of the dissolution of elemental gold in ammoniacal solutions have been investigated. The cathodic reaction of aurous di-ammine on the gold cathode has been investigated first. From this investigation, the standard electro-potential of the cathodic reaction .and hence. the Gibbs free energy of formation of the aurous di-ammine were established. The solubility of gold in ammoniacal solutions was also examined in relation to ammonia concentration, temperature and concentration of various oxidants. The anodic reaction of the gold disk in ammonia? in the presence? of various oxidants including oxygen, ozon, hypochlorite, hydrogen peroxide, cupric and cobaltic ammine, and iodine was also examined and the results have been discussed. Excellent dissolution yielding of gold and many other metals, typically better than 95% recovery in 1'-2 'hours of leaching at a temperature ranging 80°C to 190°C has been observed. Test results of the dissolution of gold from elemental state as well as other sources including sulfidic ores and scrap are presented.

Jan 1, 1998

By Sugui Tian

By means of the T6 treatment, the measurement of creep curves and microstructure observation, the influence of T6 heat treatment on the microstructure and creep properties of Ti-6Al-4V alloy is investigated. Results show that the microstructure of the forged alloy consists of the banded-like a phase and networks b phase. After sub-temperture T6 treated, the microstructure of alloy consist of the block a phase and ?networks basket? structure. Under the conditions of the applied stress of 575 MPa at 4000C, the forged alloy displays a lower creep lifetimes, after T6 treated the creep lifetimes of the alloy is enhanced to 548 h from 66 h, which is attributed to the formation of the network basket structure in which the needle-like phase are dispersedly distributed. As creep goes on, the denser dislocations in the a phase are concentrated to occur the dynamic recrystallization for refining grain. which is a main reason of the alloy displaying a better creep lifetimes and plasticity. Thereinto, the creep mechanism of the forged alloy is thought to be the slip of the straight <a> and <a+c> dislocation are activated on the prismatic planes and pyramidal planes, while the creep mechanism of T6 treated alloy is that wave-like <a+c> dislocations are activated on the pyramidal planes.

Jan 1, 2009

By I. M. Richardson, M. Janssen, W. Geerstma, I. J. Bennett, V. A. Popovich

Avoiding wafer breakage is a big challenge in the photovoltaic silicon industry, limiting production yield and further price reduction. Special fracture strength tests suitable for thin silicon solar wafers and solar cells, to be used in combination with Weibull statistics, finiteelement (FE) modelling and digital image correlation have been developed in order to study the mechanical stability of solar wafers. The results show that removal of the saw damage significantly increases the strength of crystalline silicon wafers. Furthermore, it was found that silicon crystallinity and the location where the wafer is extracted from the cast Si ingot have a significant effect on the strength, namely samples taken from the bottom of the ingot are 30% stronger than those taken from the top. The study also showed that there is a decrease in fracture strength when an anti-reflective SiNx coating is applied, which is caused by high thermal stresses.

Jan 1, 2015

By Jinqian Zhao, Jiarong Li, Shizhong Liu

"Creep cavitation of in single crystal (SX) superalloy was investigated. The constant load creep tests, in single crystal superalloys DD6, were conducted at the conditions of 800°C/700MPa, 850°C/550MPa and 900°C/450MPa, respectively. It was found that there were square facets on the stress fracture surface, and microscopic cavities in the ruptured specimens in the vicinity of the fracture surface. Both the square facets on the fracture surface and microscopic cavities in the section of the ruptured specimens show the morphology of the same thing at the different views, namely creep cavities, which are take the form of flatten cuboid. In fact, creep cavities are the longitudinally tensiled creep cracks slowly growing during the stress tensiling. The factors of creep cracks nucleation and growth conditions include: (a) enough high temperature to activate diffusion (b) casting pores as nucleation origination (c) high strains and strain rates. Eventually, the instantaneous fracture mechanism of creep specimen is cleavage fracture.IntroductionFor the materials used in elevated temperature service, creep behavior has to be accounted for. It is well recognized that creep rupture in polycrystalline materials at high temperature occurs principally by the nucleation and growth of microscopic cavities at grain boundaries, followed by microscopic cavities linkage to form micro- and eventually macro-intergranular cracks[l,2]. Without the usual grain boundaries, SX superalloys have superior capabilities at high temperatures to polycrystalline superalloys, and have become an established feature of gas turbine technology where they are commonly employed in the manufacture of high performance blades[3]. A considerable amount of work has been done over the past tens of years, and many models for nucleation and growth of creep cavities have been proposed, however, those are mainly for polycrystalline materials.In order to improve creep resistance that single crystal superalloys, in which grain boundaries are removed, have been developed. Because there don't exist grain boundaries in SX superalloy, the mechanism of nucleation and growth of creep cavities must be different from that in polycrystalline materials.Understanding the formation and characteristics of creep cavitation is crucial to model the lives of single crystal superalloys.M. Marchionni and L.G. Zhao et al. found that there were square facets on the stress fracture surface [4,5]. Roger C. Reed pointed out creep cavities lie in the necked region[6]. In this paper, the effects on the formation of creep cavities are discussed, as well as the morphology of creep cavities and fracture mechanism of SX superalloys."

Jan 1, 2013

By S. Ajima

The Naoshima Smelter and Refinery is the most important copper operation of Mitsubishi Materials Corporation. There are a Mitsubishi Continuous smelter and a conventional type of copper tankhouse. The continuous smelter with 240,000 mtpy of anode production was commissioned in May 19914 replacing two existing smelters, i.e an original Mitsubishi Process line and a conventional reverberatory furnace line. In July 1992, the copper tankhouae was expanded for the purpose to close the gap of production capacity between the smelter and the tankhouse. The cathode production capacity was increased from 13,800 to 15,800 mtpm. By these plant modifications, the distribution of minor elements was significantly changed and the impurities load is getting on increase reflecting recent shortage of clean copper concentrates supply. The paper discusses the distribution of minor elements and the impurity control strategy at the smelter end the refinery.

Jan 1, 1995

By Sven Eck, Andreas Ludwig, Menghuai Wu

"Phase separation is a frequently occurring phenomenon during solidification accompanied by melt convection, sedimentation or, in the case of two unmixable liquids, a Marangoni driven motion. In order to describe these phase separation phenomena a two-phase volume-averaging model was employed for globular equiaxed solidification of binary alloys and decomposition and solidification of hypermonotectic alloys. The model considers nucleation and growth of equiaxed grains or second phase droplets, motion and sedimentation of grains or droplets, feeding flow and solute transport by diffusion and convection. It allows the prediction of macro segregations and the distributions of grain size or droplet size. Evaluations were made by comparing the numerical predictions with experimental results. For example it is shown that the numerically predicted grain size distribution in a plate casting (Al-4wt%Cu) agrees reasonably well with the experimental analyses.IntroductionModeling of metallurgical processes is a rapidly expanding field and the research activities in the last decades cover a wide range of areas including melt pre-treatment, solidification and subsequent manufacturing routes. Among those activities solidification stands in the central position, because the primary structure of the materials, and even many defects such as porosity, (macro or micro) segregation and inclusions form during solidification. Those primarily formed structures or defects once existing are difficult to be removed or modified by the subsequent material processing.Solidification is a multi-disciplinary field involving thermodynamics, fluid dynamics and solid mechanics, heat and mass transfer, and other disciplinesr1 -31• One of the most challenging problems in solidification modeling is the complex interactions between physical phenomena occurring on different length scales ranging from atomic rearrangement over single crystal-melt interactions to heat extraction, momentum and species transport at the system level. Modeling an industry process on atomic scale is umealistic, even on grain scale (e.g. phase field method) it would need another 40 years to be able to model the exact grain morphology in a casting space envelope of 10x10x10 cm3 [ 4]. Therefore, the realistic models for industry process are based on the solution of the macro transport equations (mass, momentum, enthalpy and species) on system scale. The microscopic phenomena such as thermodynamics, nucleation law, crystal growth kinetics and interactions at the liquid-solid interface are considered with simplified models, which are coupled with the macroscopic transport equations."

Jan 1, 2004

By John J. Dunkley

Recent years have seen the increased use of hydrometallurgy in the smelting and refining of metals. However this is often used as a final refining step, following an initial pyrometallurgical smelting process. Huge amounts of material are produced as melts which have to be cast, comminuted, and taken up into solution or leached. A common method is to granulate the melt and then grind it. In the case of metallic melts this can be difficult or unfeasible due to the ductility of the granulated particles. Water atomisation is capable of replacing the granulation and grinding stages with a single process step that can process in excess of 30tlhour of melt into particles as fine as 50 microns. Applications in operation in Co, Cu, Ni, Ag, Au, Pt and Rh refining are discussed together with potential applications in copper smelting.

Jan 1, 2003

By John J. Dunkley

Recent years have seen the increased use of hydrometallurgy in the smelting and refining of metals. However this is often used as a final refining step, following an initial pyrometallurgical smelting process. Huge amounts of material are produced as melts which have to be cast, comminuted, and taken up into solution or leached. A common method is to granulate the melt and then grind it. In the case of metallic melts this can be difficult or unfeasible due to the ductility of the granulated particles. Water atomisation is capable of replacing the granulation and grinding stages with a single process step that can process in excess of 30t/hour of melt into particles as fine as 50 microns. Applications in operation in Co, Cu, Ni, Ag, Au, Pt and Rh refining are discussed together with potential applications in copper smelting.

Jan 1, 2003

By J. P. Evans

The modem copper smelter today utilizes tonnage oxygen for smelting concentrates, generating a high strength S02 off-gas leaving the smelter vessel. This gas stream, which also contains any unreacted oxygen, plus C02, N2 and H20, also carries with it the volatilized portion of heavy metals in the feed, plus partly oxidized sulfide concentrates. The time/temperature history and subsequent treatment of this off-gas stream emerging from the smelting furnace exit up to the acid plant can influence the partitioning and segregation of heavy metals in the off-gas circuit. Depending on this history, the type and characteristics of the chemical and physical reactions which. occur in the gas handling system can be influenced. This fact can also be used as a tool to adjust the separation of copper from heavy metals. In this paper, the impact of different time/temperature histories of the gas, due to different furnace geometries .and design, on the subsequent formation and characteristics of the smelter dust is examined. Based on the available data, several case histories drawn from examples using both bath and flash smelting technologies are analyzed from this perspective.

Jan 1, 1992

By Guo Xueyi

The dissolution behaviors of valuable metals, lead and zinc, from secondary fly ash generated in municipal incineration plants were investigated using some lixiviants: sulfuric and hydrochloric acids, acetic acid and some chelating reagents including L-asparaginic-N,N-diacetic acid (ASDA), a biodegradable, and therefore, environmentally benign novel chelating reagent. It was found that zinc exists mainly as ZnO, whereas Pb probably as PbOHCI and PbO, and the easily soluble components in SFA are KCI and NaCl. Suitable amount of HCI can dissolve all of lead and zinc from SFA. Sulfuric acid can selectively extract zinc leaving lead in the residue. Ethylenediaminetetraacetic acid (EDTA) is an effective chelating reagent to extract both zinc and lead. Although ASDA and diethylene¬triaminepentaacetic acid (DTPA) can selectively extract more than half of lead from SFA, it would by no means be regarded as highly effective reagents for the extraction of these metal values. Keywords: Lead, Zinc, Secondary fly ash, Leaching, Dissolution

Jan 1, 2002

By J. P. Evans

The modem &apos;copper smelter today utilizes tonnage oxygen for smelting concentrates. ,generating a high strength S02 off-gas leaving the smelter vessel. This gas stream. which also contains any unreacted oxygen, plus CO2; N2 and H20. also carries with it the volatilized portion of heavy metals in the feed, plus partly oxidized sulfide concentrates, The time/temperature history and subsequent treatment of this off-gas stream emerging from the smelting furnace exit up to the acid plant can influence the partitioning and segregation of heavy metals, in the off-gas circuit. Depending on this history. the type and characteristics of the chemical and physical reactions which occur in the gas handling system &apos;can be influenced. This fact can also be used as a tool to adjust the separation of copper from heavy metals. In this paper, the impact of different time/temperature histories of the gas, due to different furnace geometries and design. on the subsequent formation and characteristics of the smelter dust is examined. Based on the available data. several case histories drawn from examples using both bath and flash smelting technologies are analyzed from this perspective.

Jan 1, 1992

By Shenghui Guo, Ying Lei, Hao Niu, Huilong Luo, Jinhui Peng, Libo Zhang, Yu Li

"In this work, the combination of microwave drying (MWD) and heat pump drying (HPD) drying experiments were designed by response surface methodology (RSM) based on central composite design (CCD) using design expert software (Version 7.15), and the process parameters were optimized. The conditions given by software are: the MWD time is 4.6 or 4.4 min; the HPD time is 9.0 or 8.6 min; and the sample mass is 620 or 600 g. Under those conditions the moisture content is 1.0 10-2kg water/kg wet basis, and the effectiveness ratio is 0.70 kg water/kwh. The results of confirmatory experiments conducted under the optimized conditions show the combined drying have superiority of decrease of energy consumption and increase of handling capacity over the single MWD or HPD.1 IntroductionSilica sand is one of a silicate mineral with properties as hard, anti-friction and less reactive, commonly used as raw material for foundry and construction. The silica sand obtained from mineral dressing processes such as scrubbing, magnetic separation and flotation. Its moisture content is approximately 0.08~0.12 kg water/kg wet basis. The most common methods used for drying are solar drying and hot air drying. But these methods have some shortcomings: for example, the solar drying has longer process time due to low energy yield, [1] hot air drying has low-energy efficiency and a lengthy drying time. [2]Microwave is electromagnetic waves with frequency are 300MHz to 300GHz. The outstanding features of microwave heating are rapidity and selectivity. The water specific inductive capacity of 60~78 is much bigger than common materials, the moisture always quickly absorb electromagnetic wave and rapidly transfer to vapors. So, it can significant reduce the drying time. [3] Heat pumps (HPs) are devices for raising the temperature of low grade heat energy to a more useful level using a relatively small amount of high grade energy."

Jan 1, 2011

By Hylton McWhinney, Doanh Tran, Jewel Andrew Gomes, George Irwin, Sameer Pallavkar, Md Islam, David Cocke, Mohammad Rafiqul Islam

"High-performance nickel-based nanocrystalline zinc oxide adsorbents have been prepared adjusting Ni/Zn mol ratio of 1 :5 by thermal decomposition, coprecipitation and sol-gel method for selective adsorption of thiophene in liquid hydrocarbon fuels at ambient temperature and pressure. To understand the nature of reactive adsorption of thiophene (C4H4S) on Ni/ZnO, the effect of preparation techniques, morphological and textural structure on the desulfurization activity was investigated. A model fuel (20 mL) consisting of pentane (C5H12) and thiophene was prepared and adsorption experiments were performed by a batch method under ambient conditions. The physicochemical behaviors of the fresh adsorbents were obtained using X-ray diffraction (XRD) with EDAX, scanning electron microscopy (SEM). The sulfur concentration in the mixture was monitored by UV-vis spectrophotometry. The adsorption reaction confirmed that ZnO played a crucial role in taking up S element to convert it into ZnS. The deposition of nickel on ZnO is an innovative approach which takes advantage of the selectivity of Ni towards S-species and the high adsorptive capacity of ZnO support.IntroductionLow temperature deep desulfurization of fuels via selective adsorption of sulfur compounds keeping coexisting aromatic hydrocarbons and olefins intact is receiving increasing attention in the research community worldwide in order to satisfy the upcoming environmental regulations and fuel specifications. The sulfur compounds in the transportation fuels is a matter of concern when global crude oil slate is becoming heavier and sourer and environmental restrictions on both the refining process and the refined products are becoming more stringent. According to the current refinery technologies, the sulfur content in refinery fuel is typically around 300-500 ppm by weight (ppmw) [1-3]. Starting in 2006, sulfur limits in highway diesel and gasoline were set to 15 ppm and 30 ppm, respectively. During combustion sulfur in the fuel are converted to toxic sulfur oxide (SOx) and contributes to air pollution and acid rains [ 4]."

Jan 1, 2011

By D. Mishra

Electric arc furnace dust (EAFD) generated during the recycling of steel- scrap is classified as a hazardous waste for landfilling. This is because it contains leachable heavy metals such as zinc, lead,... Recovery of these metals could result in both resources conservation and resolving waste disposal problems. A study of the thermal reduction of a sample of EAFD was carried out in an inert gas atmosphere using coke as a reducing agent. Preferential volatilization of zinc and lead was achieved during the reduction process at about 800 "C. More than 96 % of both zinc and lead were removed from the dust and were recovered in the condensates. The treatment residue was essentially composed of iron oxides and almost free from heavy metals.

Jan 1, 2002

By Kexin Jiao, Zhijia Zhang, Jianliang Zhang, Zhengjian Liu

Carburization behavior of molten iron in blast furnace is an essential part of BF long campaign technology. Maintaining carbon content stable is an important prerequisite to ensure the high production of the blast furnace. In this paper, the important aspects of the research progress which mainly including the study of iron carburization at the upper and the lower parts of the blast furnace was reviewed. Indirect carburizing is the main way at the top of the blast furnace. The content of carbon in metallic iron increases with the reducibility of iron ore improved. The thermodynamics and kinetics conditions are good for carburization reaction to take place at the bottom of the blast furnace. Carbon content of molten iron increased by coke carburizing. Meanwhile, the drawbacks of the existing literature on iron carburization behavior were analyzed and new research directions of iron carburization were proposed in the future.

Jan 1, 2015

By Denise Corrêa de Oliveira

Common dry batteries use zinc as the negative electrode. Producers commonly use additives such as mercury to prevent corrosion and to increase the mechanical resistance of the zinc anode. Alkaline batteries also contain it, as an anti-corrosive agent. When mixed with the common municipal solid waste, heavy metals as zinc and mercury pollute soil and ground water supplies, moving to the food-chain and affecting human health. Due to these possible damages, this kind of waste must be properly disposed, or recycled. Thus, even in low amounts (ppm) in batteries, mercury has to be eliminated or, at least, its content should be reduced. This work presents the use of pyromettalurgical processes, to reduce mercury content and recover zinc. The tests involved batteries treatment at temperatures from 300° to 1000°C. Mercury is eliminated up to 650°C, and zinc is evaporated at higher temperature treatment. C

Jan 1, 2001

Arsenic occurs naturally in rocks and soils, water, air, plants and animals. It can be further released into the environment through natural activities such as volcanic action, erosion of rocks and through human actions. Higher levels of arsenic tend to be found more in ground water sources than in surface water sources of drinking water. Compared to the rest of USA, western states have more systems with arsenic levels greater than 10 parts per billion (ppb). The US Environmental Protection Agency (EPA) has historically regulated arsenic in drinking water at 50 ppb, but the agency has lowered the maximum contaminant level (MCL) for arsenic to 10 ppb-to be in compliance by January 2006.This paper reviews briefly a) aqueous arsenic chemistry and removal mechanisms and b) the available treatment processes to attain the drinking water standard of 10 ppb by 2006. The combining of an appropriate removal method with an existing system depends on several factors such as nature of arsenic, the water source, existing plant equipment and processes site conditions etc. The paper also includes one or two case studies from the State of Arizona. Key words: Arsenic, Drinking water, Treatment Technologies

Jan 1, 2005

By Rodney T. Jones

DC arc furnaces were first used industrially for the reductive smelting of chromite fines to produce ferrochromium thirty years ago. Since then, they have been used for a variety of applications, including the smelting of ilmenite to produce titania slag and pig iron, the recovery of cobalt from non-ferrous smelter slags, and the smelting of nickel laterite ores to produce ferronickel. The power of these furnaces has increased from 12 MW to 72 MW for ferrochromium, and to 80 MW for ferronickel. The largest of these furnaces requires two electrodes to carry sufficient current to generate this much power. A review is presented of various DC arc furnaces in use, along with a discussion of the likely ways in which furnace power might be increased further in the future.

Jan 1, 2014

By Chuanfu Zhang, Liwei Liang, Yanxin Wu, Jinliang Wang

"According to the reaction shaft operation characteristics during the flash smelting process, 15 groups of slag samples containing high Fe3O4 were prepared by some chemical reagents, and then the slag viscosities were measured using a RTW-10 type synthetic test instrument for melt physical property by the rotating cylinder method. The effects of Fe/SiO2 ratio (mFe/mSiO2), Fe3O4 content (wFe3O4), Cu2o), MgO content (WMgO) and Cao content (wCaO) on the slag viscosity were also studied. Results show that slag viscosity is decreased with the increase of temperature, mFe/mSiO2, wCu2o, wMgO and wCao, and with the decrease of wFe3O4, under the range of slag contents: mFe/mSiO2 1.36~1.78, wFe3O4 17.83%~21.18%, wCu2o 3.51%~8.34%m wNgI 2.21%~6.57%m w/caI 6.22%~9.387% and temperature range if 1250 o/c~1450 oC. Only wFe3O4m and w/caO have great influence on the slag viscosity when temperatures as high as 1400 oC. Only wFe3O4 and wCaO have great influence on the slag viscosity when temperatures as high as 1400 oC or so. To form a freeze slag with higher viscosity inside the reaction shaft, wFe3O4 should be more than 20% and wCaO should be less then 6%.IntroductionSince its appearance in 1949, Outokumpu flash smelting technology has making continuous innovation and has become the most competitive intensified smelting technology [1], widely considered to be the standard clean smelting process [2]. At present, flash smelting technology is adopted to newly build or reconstruct most of the world's copper or nickel smelting enterprise [3]. Reaction shaft is the most important part of the flash smelting furnace. During the flash smelting process, reaction shaft must be able to withstand the following harsh conditions at the same time: 1) high temperature varying from 1400 °C to 1500 °C. 2) strong oxidative atmosphere containing 50% - 80% oxygen. 3) solid particles and melt with speed up to l00 m/s. 4) high acidic or basic slag with strong chemical corrosiveness. 5) smelting gas containing 50% - 80% SO2. 6) matte with strong dissolution."

Jan 1, 2012