Search Documents

By F. Sanchez, A. Mejias, C. Frias, G. Diaz

"Crude zinc oxides are the major source of secondary zinc and are produced from fuming processes like Waelz kilns. The impurities of crude zinc oxides make difficult their processing in primary zinc refineries due to mainly high chloride tenor. Washing with sodium carbonate is a costly operation and chloride removal efficiency is not good enough, so further purification steps are required. The crude zinc oxides are easily treated using ZINCEX™ technology based on leaching, solvent extraction, and electrowinning. The ZINCEX™ process is commercially available and is designed to be a perfect barrier for metallic impurities and halogens, allowing selective zinc extraction in mixed chloride and sulfate leaching solutions. Other valuable components as lead and silver can be efficiently recovered from the leaching residue using PLINT technology in chloride media. Silver is recovered as silver cement and lead is precipitated as pure lead oxide or carbonate, which can be smelted at low temperature.IntroductionZinc is a fully recyclable metal and at present approximately 70% of the zinc produced worldwide comes from primary zinc while 30% originates from secondary materials. Nowadays, the zinc recycling rate is continuously increasing mainly through galvanized steel scrap processing, and crude zinc oxides are the major source of secondary zinc [1]. Secondary zinc oxides are obtained from fuming processes like W aelz Kiln, Rotary Hearth Furnace or Primus Furnace. Waelz is the dominant technology accounting for 80% of total crude zinc oxides production worldwide. In the Waelz process, steel dust is mixed with solid fuel reductant (coke breeze) and pelletized. It is then fed to the kiln and heated to a reaction temperature of l ,200°C. In such conditions, zinc, lead, and other non-ferrous metals are vaporized into the flue gas together with chlorides and alkaline metals. Mixed oxides are drawn from the kiln with the process gases and separated to produce typical crude zinc oxides [2]."

Jan 1, 2011

By T. K. Mukherjee, C. K. Gupta

"The importance of the processing of secondary resources such as solid industrial wastes and liquid effluents as well as byroducts for the recovery of the associated metal values hardly needs any elaboration. Such processing contributes in no small measure towards the augmentation of the availability and the supply position of resources. As an added benefit, it leads to a reduction in environmental pollution caused by the undesirable waste materials. As some typical examples of secondary resources in the Indian scenario, mention can be made of spent catalysts, metal/alloy scrap, ash, consumed batteries, flue dust, slag, sludge and slime, pickling solutions, spent acids, plating rinse solutions, spent etchants, waste water from synthetic fibre manufacture and from tanneries etc .. These wastes constitute a source of a variety of non ferrous metals. In the processing of secondary resources like these, the techniques of hydrometallurgy such as solvent extraction playa pivotal role.This paper outlines the efforts made to use solvent extraction to recover (1) base metals such as copper, zinc, nickel and cobalt from a number of secondary resources like cake, and sludge (2) refractory metals like molybdenum and vanadium from sulphidic byproducts and spent catalyst and (3) nuclear metal like uranium from phosphoric acid. In the case of base metals, process flowsheet involving the use of acidic extractants such as DEHPA and PC88A have been optimised. The problem of iron removal from the leach liquor, which influences the metal recovery process significantly, has drawn a special emphasis. In the case of refractory metals, basic extractants like Alarnine 336 has been pressed into service to produce kilogramme quantities of pure salts of molybdenum and vanadium. Finally, the paper gives a brief account of plant experience in recovering uranium from phosphoric acid, using a solvent system comosed of DEHPA and TOPO."

Jan 1, 1996

By Jian Li, Guo Chen, Bingguo Liu, Hongying Xia, Jinhui Peng, Libo Zhang

"Decomposition of ammonium tetramolybdate to prepare Mo03 using silicon carbide crucible in microwave fields was investigated. The results were analyzed Using TG-DTG and X-ray diffraction. Meanwhile, the effects of heating rat, material thickness, socking time, socking temperature on the structure of preparing Mo03 were studied. TG-DTG curves show that the decomposition process of ammonium tetramolybdate is only one stage, in the temperature range 300-350°C, whose begin to decompose when temperature increases beyond 300°C. The molybdenum trioxide was prepared by thermal decomposition. The quality ofMo03 was not affected under the heating rat is 12°C/min. It was beneficial for decomposition ratio with the lower material thickness, longer soaking time, and higher soaking temperature. XRD curves showed that it is viable method for preparation of Mo03 by decomposition from ammonium tetramolybdate in microwave fields.IntroductionMolybdenum is widely used in national defense, aviation, industrial and agricultural production as rare refractory metal. Molybdenum trioxide is vital raw materials for the process of preparation of molybdenum. The traditional production technology of molybdenum oxide is that ammonium tetramolybdate is calcined in rotary kiln or 4-tube furnace [J,2J. But the longer production time, the higher production cost, the lower furnace thermal efficiency, and bigger the energy consumption, especially the powder is easy to leak, the working environment is poor by using rotary kiln [ 3 l _ The particle of molybdenum oxide is non-uniform by using 4-tube furnace because of the uneven temperature of every tube and the poor exhaust of boat bottom [4l _ However microwave heating is quick and uniformity, it is a meaningful research that the microwave is used in the process of calcining ammonium tetramolybdate."

Jan 1, 2013

By T. R. A. Davey

The technologies of lead, zinc and tin extraction have made varying degrees of progress over the past twenty years. Producers of all metals have faced increasing demands for reduction of pollution and environmental degradation, and the level of public concern is rising rather than abating. New processing techniques must therefore be not only economically feasible, but politically acceptable, even when the demands of "conservationists" and ?environmentalists? are unreasonable. A new generation of processing techniques has come into being, which do not rely on an expensive sintering stage, nor use metallurgical coke, which is difficult to make without serious pollution. They utilise intense reactors, conveying materials from one stage to the next preferably within an enclosed space, obviating fume emissions, and avoiding heat losses as far as possible. The acceptability of the new techniques? is increased if lowgrade or complex materials can be treated, along with a variety of returns and wastes. In addition, a good selling and servicing organisation seems to be as important as good process technology in determining the spread of the new processes. In the field of pyrometallurgical refining the need is for more general application of several recently developed techniques rather than a search for alternatives to the existing process technologies. However, there is a need for fundamental work investigating the phenomenon of oxygen anode overvoltage in the electrolytic zinc process, in order to make progress in the further reduction of energy consumption. There is also scope for further development and application of vacuum distillation to up-grade thermally produced zinc. This paper presents a personal view of processes which should be developed to overcome existing problems, as we approach the turn of the century,

Jan 1, 1990

By Yufeng Guo, Tao Jiang, Jianjun Fan, Haizheng Hao

"Function of High Pressure Roll Grinding (HPRG) in production of oxidized pellets from magnetite concentrate as raw material was systematically studied. It was found that bentonite dosage decreased from 1.3% to 0.8% if specific surface area of magnetite concentrate pretreated by HPRG was up to 2553.41cm2.g-1. The green ball quality improved obviously due to the increase of specific surface area and fine particles content, and the improvements of size distribution and the ballability of pretreated materials. However, the decrease of pellet porosity accelerated the primary solid phase reaction and oxidation reaction, which made the pellets surface form compacted layer that handicapped the diffusion and migration of oxygen, promoting the formation of double layer structure of finished pellet. Consequently, the compression strength of preheated and roasted pellets was not markedly improved by HPRG.IntroductionWith the increase of proportion of pellets in the BF recently, the technical-economic index of BF has obviously been improved. Consequently, the production and the quality of BF pellet are given more attention [1]. However, with the decrease of the quality of iron ore concentrate, the problems such as poor ballability, high bentonite dosage, high preheating and roasting temperature are becoming the great challenges to not only the quality of finished pellets, but also the energy consumption [2, 3]. In order to overcome these problems, mechanical pretreating technologies such as the High Pressure Roll Grinding (HPRG) and Damp-grinding are widely applied. HPRG has a number of advantages such as low energy consumption, high productivity and easy-maintaining. It is more economic and environmentally friendly than the Damp-grinding technology [4, 5]. A great number of experiments have revealed that HPRG can improve the quality of hematite pellets. Although there are some studies of function of HPRG in the magnetite oxidized pellet production, they are not comprehensive and systematic, especially to the preheating and roasting system [1, 2, 6, 7]. Accordingly, the influence of HPRG on the pelletizing system and the preheating and roasting system are systematically studied in production of magnetite oxidized pellets in this article."

Jan 1, 2011

By Henry Hu

In high pressure die casting processes, proper control of temperature die yields a high casting production rate and superior quality components, Die temperature is usually influenced by various die design and process parameters such as size and location of intemal water cooling lines, flow rates of cooling lines, and pouring temperature of molten metal. Among them, the cooling water flow rate plays a major role in controlling thermal pattern of the die_ In order to develop an effective control strategy, data of local die temperature must be collected and analyzed, In this study, a PC-based data acquisition and control system (DACS) for die temperature control has been designed, and established, The developed DACS has three input channels for temperature signals and one input channel for water flow rate signals, as well as one output channel for a water pump, and is capable of displaying data in both curve format and value format. Implementation of the DACS in a laboratory setup has also been attempted, It should be pointed out that more advanced control mechanisms can be potentially integrated into this system in future,

Jan 1, 2003

By Malti Goel

"Technology advancements in fossil fuel based energy generation and consumption are currently being aimed at minimization of CO2 emissions. To attain energy security, India must accelerate the pace of economic development, while achieving reduction in CO2 emissions per unit of energy consumed. It would need access to advanced coal utilization technologies to be demonstrated on indigenous coal characteristics. Of specific importance would be: improvement in coal quality, increasing energy efficiency and suitability of other CO2 sequestration technologies for reducing CO2 footprints. There is need to address related risks and financial burden through adoption of policies and regulations including the issue of open access in energy research. In this paper, seven important areas of strategic plan that need to be pursued for managing CO2 emissions in steel energy sector in India are discussed.IntroductionWorld is facing a crisis of climate change, which follows in the footsteps of global energy and environment crises. Accumulation of carbon dioxide from the generation and utilization of energy is leading to greenhouse warming and climate change. The global warming is causing the boundary between four seasons to be fuzzy and resulting in more spiky weather. Significance of its impact on environment is also determining the technology development needs in various sectors of economy for taking remedial measures.To respond to climate change concerns, the steel industry is undergoing a transition. It is at the threshold of a rapid change in technology as it targets innovation to achieve 50% reduction of CO2 emissions per ton of steel produced. Fossil fuel use is the main contributor of increasing concentration of carbon dioxide in the atmosphere. The control of air pollution and CO2 capture are thus relevant for a coal based industry, whether thermal power plant or a demand side energy intensive industry. World steel production has shown phenomenal increase in first eight years of 21st century increasing from 780 Mt in 2000 to 1343 Mt in 2008 [1]. It was merely 28 Mt in 1900. The global CO2 emissions from steel industry are also increasing and became 2550 Mt (3-4% of total GHG). Indian industry contribution was 161 Mt (15% of direct emissions from industry). It is likely to grow further to keep pace with the accelerated economic growth of 8-9% per annum."

Jan 1, 2010

By G. G. Richards

"The slag fuming process has operated for close to 70 years to recover zinc from lead blast furnace slag. The process is normally carried out through the batch treatment of slag by submerged injection of coal and air. Within the bath the coal acts as both a reductant, to reduce Zno to zinc vapour, and a fuel, to maintain bath temperature during the endothermic reduction process. The partition of coal between the slag, combustion and bypass is dependent on factors such as bath depth and injection pressure. The option of continuous fuming has been pursued at the D. Blagoev smelter in Bulgaria using heavy fuel oil as reductant/fuel. There has, however, been little attempt at commercial continuous fuming with coal. This paper presents an analysis of a coal-based continuous slag fuming furnace. The data on the Plovdiv fumer is used as a reference point. Critical design criteria for continuous fuming include the slag feed rate, degree of coal combustion and furnace size. Mathematical modelling analysis suggests that continuous fuming with coal can achieve respectable zinc/coal ratios.IntroductionThe slag fuming process was developed in the early part of this century to recover zinc from non-ferrous smelting slags [1-3]. The majority of installed furnaces were put in place to fume zinc from lead blast furnace slag on a batch basis. In most cases coal is used to effect reduction of zinc oxide, but one furnace uses natural gas [4] and, in a curious twist, a continuous fumer was developed based on fuel oil [5].Given the general nature of blast furnace lead smelting, it is not surprising that slag fuming has remained a batch process, in spite of the advantages that could be gained by moving to continuous fuming. Blast furnaces are usually operated as relatively independent units, and tapping has traditionally been done into ladles. The presence of a crane aisle makes direct coupling of the blast furnace to a slag fumer difficult, especially in a retrofit situation. Furthermore, steady-state blast furnace operation is not easy to achieve. The size of these furnaces and the nature of their feed make it difficult to guarantee constant operation."

Jan 1, 1996

By Emil B. Milosavljevic

Problems associated with distillation and other classical methods for analyzing operationally defined cyanide (CATC, WAD, Total and Free Cyanide) will be discussed. These methods often achieve incomplete, species dependent cyanide recoveries and suffer from serious interferences. Depending on the relative concentrations of interferents and other matrix constituents, underestimation (ultimately Type II errors probability of not detecting a constituent when it is actually present) or overestimation (ultimately Type I errors -probability of deciding a constituent is present when it is actually absent) of the cyanide levels present in a ,given sample may occur, causing in the first case false security and in the second case, excessive cyanide treatment costs. Mahy, if not all, enumerated problems can be solved by using novel flow injection (FI) gas-diffusion amperometric methods. A modification of the recently approved FI ligand exchange (FIILE) method for determination of available cyanide (USEPA Method OIA-'l677) that obviates sulfide interference will be discussed. Eight laboratory round-robin data obtained for the FI UV -digestion (FIIUV) method that determines total cyanide (Proposed Method OIA-1678) will also be presented. In addition, some methods for cyanide speciation will be presented. Finally, research needed for developing reliable methods for determination of operationally defined cyanide in solid samples will be summarized.

Jan 1, 1998

By Y. Wang, L. Liu, G. Xu, Y. Lv J. Sheng H. Zhang

In order to increase the service life of large scale coke dry quenching furnaces, the damage mechanism of lining was investigated, and the structure and properties of lining refractories used in cooling section were researched. The results showed that the abrasive wear volume of lining bricks at one fourth height section under skew tunnel was smaller than other sections. The wear loss of mullite brick and dense clay brick used in the lining of cooling section were respectively 8.02 cm3 and 11.65 cm3 in fifteen minutes. The mullite brick was laid with clay brick alternatively. By the different wear rate, the surface of lining was rough and uneven in the later service life, and short brick was easily dropped from lining. During the service, the basis wore off more easily than the aggregate. It is necessary to improve the wear resistance property, which will increase the service life of cooling section’s lining for coke dry quenching furnaces.

Jan 1, 2016

By Zhang Chuanfu, Li Shixiong

"In the electrolysis electrodeposition or electroplating of aqueous solution of copper, lead, zinc, nickel, manganese etc, with the increase in cathodic over potential the reducing rate of metal and the cathodic current efficiency increases and the deposit becomes more compact and smooth. According to this principle, a method and equipment of the auto-control of electrolyte quality is invented. The industrial application shows that this method turns the experienced operation into auto-control. The quality and quantity of metal is improved greatly and the consumption of electric energy is reduced.In the electrolysis, electrodeposition or electroplating of aqueous solution of copper, lead, zinc, nickel, manganese etc, usually organic additives are added according to the state of cathodic deposit according to experience. This traditional and experienced operation, often lead to that the quality of additive is not optimum which affects the quality and quantity of metal and increases the consumption of electric energy. To counter the controlling problem of the quantity of additive, the authors have invented a corresponding equipment of the auto-control of electrolyte quality [1], it has found application in industrial practice."

Jan 1, 2000

By G. R. Waters

NMR360 is developing a suite of chloride-based metals extraction processes, with the first commercial operation scheduled for commissioning late in 2018. It is critical, therefore, that with the introduction of any new technology, that the circuits do not suffer from mechanical failures which will compromise the operation. Although chloride leaching is at atmospheric pressure and relatively low temperature, the main challenge is preventing corrosion, since the high proton activity makes even a small amount of acid behaves as though it were concentrated. An additional challenge in concentrated chloride circuits is the potential for solids precipitation. In this context, therefore, correct valve selection is crucial, and NMR360 has partnered with CGIS to ensure that the Severe Service Valves (SSVs) needed will perform over and above the definitions of the Manufacturers Standardization Society (MSS) of the Valve and Fittings Industry. This paper outlines what the minimum requirements are for SSVs in chloride leaching applications, drawing on five decades of industry experience from one of Canada’s leading valve experts.

By David B. Dreisinger

Mass and heat balance modeling is a powerful tool for the design and analysis of hydrometallurgical process flowsheets. In this first of two papers, we examine the basic fundamentals of mass and heat balance modeling, and apply these concepts to several flowsheets using a simple spreadsheet model. In this way, we aim to demonstrate how such models are not only easy to construct, but can also be indispensable for comparing various flowsheet alternatives, for making rational economic decisions, and for developing a basic understanding of existing process behaviour.

Jan 1, 2002

By E. V. Verhoef

The proposed EU directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment promotes the substitution of lead in consumer electronics to reduce emissions from lead in the end of life phase. In this paper, the consequences of substituting lead in solders is assessed using the Eco-lndicator-99 method for the examples. The base metal production system is considered as an interconnected network modeled dynamically in Simulink 4 and Matlab 6 (Mathworks Inc 2000), where the recovery and production of metal components of the assessed product partially overlap. This approach requires global modeling of metal production processes and mass balances and resulting allocation choices. It also reveals the susceptibility of LeA scores to different choices in the modeling and data availability and uncertainty. Besides the comparison between lead-free and lead-containing solders, other side effects are revealed. Lead is carrier material for the recycling and production of many co-elements in the interconnected production and recovery system. Substitution may have adverse effects such as temporary shortages of other connected metals that are often not considered in normal LeA assessments, thus leading to erroneous results. The suggested approach provides directions for including these external effects and for further assessment of the environmental effects of substituting lead. This paper shows that in order to assess the environmental aspects of metallurgy, dynamic modeling of the total system is required based on the fundamental thermodynamics in each metallurgical reactor, the basis of this dynamic model. With this the true environmental impact of metallurgy can be explained. In the case of lead free solder, it is shown that the mining of substitutes has a very much larger impact.

Jan 1, 2003

By E. V. Verhoej

The proposed EU directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment promotes the substitution of lead in consumer electronics to reduce emissions from lead in the end of life phase. In this paper, the consequences of substituting lead in solders is assessed using the Eco-Indicator-99 method for the examples. The base metal production system is considered as an interconnected network modeled dynamically in Simulink 4 and Matlab 6 (Mathworks Inc 2000), where the recovery and production of metal components of the assessed product partially overlap. This approach requires global modeling of metal production processes and mass balances and resulting allocation choices. It also reveals the susceptibility of LCA scores to different choices in the modeling and data availability and uncertainty. Besides the comparison between lead-free and lead-containing solders, other side effects are revealed. Lead is carrier material for the recycling and production of many co-elements in the interconnected production and recovery system. Substitution may have adverse effects such as temporary shortages of other connected metals that are often not considered in normal LCA assessments, thus leading to erroneous results. The suggested approach provides directions for including these extemal effects and for further assessment of the environmental effects of substituting lead. This paper shows that in order to assess the environmental aspects of metallurgy, dynamic modeling of the total system is required based on the fundamental thermodynamics in each metallurgical reactor, the basis of this dynamic model. With this the true environmental impact of metallurgy can be explained. In the case of lead free solder, it is shown that the mining of substitutes has a very much larger impact.

Jan 1, 2003

By Deyou Yin, Kongfang Feng, Bo Wang, Jieyu Zhang, Xin Hong, Shaobo Zheng, Jinyin Xie

"The flow patterns and mixing characteristics in a water model of C-H2 smelting reduction furnace are experimentally studied in this paper. Water modeling is employed to investigate the features of gas jet stirring and the fluid flow patterns in the bath of a smelting reduction furnace during the top, bottom, and side combined blowing process. The influence of the gas flow rate for top, bottom and side nozzles, angle, submerged depth of each side nozzles and the height of the top nozzle has been examined. It showed that the gas flow rate of side nozzles and bottom nozzle had a key role on the fluid flow and mixing characteristics. The gas jet from the top nozzle could change the agitation and fluid flow pattern caused by the gas jets from the side nozzles in the bath.IntroductionFacing the current natural resources decrease and the environmental degradation, smelting reduction iron-making technique is believed to be the most representative at present. Mid last century, the concept of producing liquid iron or semi-steel directly from ore fines and inexpensive fuel was the subject of considerable pilot plant development activity. Among these projects, the direct smelting process, which is the reduction and melting of iron-bearing materials by carbon and other hydrocarbons in the vessel containing a molten bath, is the most popular one. A number of direct smelting processes have been developed around the world, e.g. COREX, DIOS, HIsmelt, AISI, ROMELT, etc.These studies put forward a new technology, which through bottom nozzle blowing rich hydrogen, top nozzle blowing rich oxygen and provide preheating ore and solvent, side nozzles blowing oxygen-coal to realize smelting reduction iron-making process. Owing to the metallurgy reactions always in high temperature, which is above 1600 °C, it is difficult to visualize the mixing behavior and measure the desired phenomena in the reduction vessel. With water modeling, the primary advantages are that it is relatively easy to observe and measure the flow phenomena in the bath."

Jan 1, 2011

By Bemd. E. Langner

At Norddeutsche AfFmerie the CollaMat is an important instrument for controlling the activity of glue in copper electrolyte. Thanks to on-line measuring of the glue activity appropriate action can to taken in the event of sudden changes, such as an intemption in the glue supply, as well as long-term trends, such as continuously decreasing glue activity over days or weeks. Laboratory tests on the dependence of glue degradation on temperature have shown that relatively small increases in temperature of only 3OC cause the half change value of the glue degradation to reduce by 25 %. It is a similar picture with the sulphuric acid concentration in electrolyte. An increase in the acid concentration from 160 g/l to 200 g/l can - depending on the temperature - likewise result in a decrease in the half change value of up to 25 %.

Jan 1, 1995

By Michael A. Markowitz, Alok Singh

"Molecular self-assembly of phospholipids and other amphipathic molecules offers a versatile approach to form self-organized microstructures in various morphologies. Stabilization of microstructures in specific morphologies by polymerization renders them useful for practical applications in areas ranging from controlled release technology to template mediated synthesis of metals. Our efforts are focussed on the development of polymerizable biomembranes derived from phospholipids, their properties and utility e.g., as stable templates for studying chemistry at the lipid interface. Polymerized vesicles formed from mixtures of 1,2-bis(tricosa-1 O,12-diynoyl)-sn-glycero-3-phosphocholine, 1, with corresponding lipids having phosphohydroxyethanol,2, or -hydroxypropanol,3, headgroups have been used in electroless metal plating of vesicle surface with gold utilizing selective binding of Pd(NH3)4 2 + to 2 or 3. The surface bound palladium ion served as catalyst for metalization. Metalization of polymerized vesicles constructed from charge neutral diacetylenic phosphocholine,1, did not occur using this process. The headgroup structure of the negatively charged phospholipids and the degree of vesicle polymerization had an effect on the stability of the vesicles after metalization. Vesicles formed from a mixture of 1 with polymerizable diacetylenic phosphatidic acid, nonpolymerizable 1,2- dipalmitoyl phosphohydroxyethanol or 1,2-diacyl phosphohydroxyethanol (from soy lecithin) were not stable to metalization process. The metal coating of the vesicles was examined by electron diffraction and revealed that the gold metal on vesicles was polycrystalline and face centered cubic. The results demonstrate the utility of polymerized synthetic membranes as template for easy and efficient synthesis of nanoparticles. IntroductionPhospholipids, synthetic or natural, provide a simple and straight forward route to construct membranes in a variety of morphologies due to their inherent property of selforganization in the presence of water[1]. Vesicles are closed spherical structures comprised of concentric walls made from lipid bilayers. Vesicles are morphologically simple structures with enormous technological potential. Polymerizable phospholipids prepared by incorporating a polymerizable group in the molecules demonstrate physical properties comparable to their non-polymerizable counterparts and have the added virtue of providing enhanced physical and chemical stability to the membranes[2,3]. The size, shape and properties of the organized assemblies are dependent on the lipid structure and the nature of the aqueous environment[4,5]. The headgroup geometry, surface charge density, and spatial arrangement of the phospholipids are known to affect the surface behavior of the lipid membranes, which is evident through their interaction with other molecular (hormones, antigens, antibodies etc) or lomc species. Since phospholipid headgroup structure and charge can be modified either synthetically or by chemical perturbation of the aqueous medium (e.g., pH or ionic strength), phospholipid membrane surfaces offer a potential for developing novel strategies in those areas which involve the use of molecular reactive sites. One such strategy which could be envisioned explores the use of molecularly engineered phospholipid assemblies to design and prepare template structures to regulate formation of ordered materials [6]."

Jan 1, 1994

By Daowu Yang, Zhuo Ren, Hui Liu

"In this paper, the photochemical catalysis degradation effect of photocatalyst obtained by charcoal-supported nano TiO2 (nano TiO2 / charcoal) on the formaldehyde in the air was studied. The influences of the nano-TiO2 loading and the photoreactor structure on the efficiency of photochemical catalysis degradation of formaldehyde was reviewed.The nano - TiO2 / bamboo charcoal adsorption of formaldehyde, as well as the influences of a certain amount of formaldehyde after adsorption on its photochemical catalysis effect were discussed. The sol preparation process of Ce-doped nano-TiO2 was described. Experimental results indicated that: the surface of bamboo Charcoal still has a strong formaldehyde adsorption capacity after Supported by Nano TiO2.After adsorbing formaldehyde, the photochemical catalysis degradation efficiency of formaldehyde of the catalyst at a steady state is basically the same with new prepared catalysts’. When the thickness of the catalyst layer of the multi-ladder-type structure photoreactor is 2mm, the interval is 20mm, the absorption efficiency of formaldehyde of Nano- TiO2 / bamboo charcoal is the best . Nano-TiO2 undoped Ce responded with no degradation of formaldehyde after 2 hours, while the degradation rate of formaldehyde of the Ce-doped nano- TiO2 reached 15% 2 hours late, and the formaldehyde decontamination of the equipment reached 94%.IntroductionEmerging out of home decoration in the distribution of formaldehyde, benzene, ammonia and other indoor pollutants have been proved to be very harmful to the human body. Photocatalysis can eliminate air pollutants, in particular, can effectively degrade the air volatile organic compounds, it is a new method of air purification developed in recent years. the biggest advantage of photochemical catalysis degradation is green, this method can be available at normal temperature and pressure to degrade formaldehyde and other organic matter into carbon dioxide and water without secondary pollution.Nano-TiO2 have become the most studied photocatalyst due to its stable, non-toxic harmless, superior photochemical catalysis properties [1]. Initially nano-TiO2 powder was used as a photocatalyst, but it’s difficult to recover and easy to wear and tear [2,3]. Later, the TiO2 was used in the form of film loaded on some carriers, such as glass beads [4]. As the photochemical catalysis reaction occurred on the catalyst surface, only the organic matter adsorbed on the catalyst surface can be degraded, so the catalyst was requested that must have a strong adsorption. Combined the adsorption properties of bamboo charcoal and the photochemical catalysis activity of nano-TiO2 together. Made the photocatalyst by loading the nano-TiO2 on bamboo charcoal to degrade organic matter in the air. Nano-TiO2 semiconductor photocatalyst has a strong catalytic oxidation due to the photo generated hole of the surface [5,6],and has a potential application. Some studies have shown that nano-TiO2 photocatalysis activity can be increased by doping certain metal ions [7,8].The aim of our work in this study was to use bamboo charcoal load Ce-doped nano-TiO2 photochemical catalysis oxidation to degrade formaldehyde,and design a multi-ladder structure photoreactor, also prove the availability of the device from the theoretical and experimental."

Jan 1, 2011

By Hiromichi Ohla

Precise thermal properties of molten materials are essentially required for analyzing the metal production process. These properties are also important as a clue to consider the dynamic structure of liquid materials. However, it is difficult to obtain the precise thermal diffusivity values of molten oxides at high temperature because of the experimental uncertainties arising from the bubble formation or the severe separation of radiative and conductive heat components. Recently a novel laser flash method has also developed for measuring thernnal diffusivity of molten oxides at high temperature. In this new technique, the sample is melted in a metal crucible and heated to the desired temperature. A single laser pulse is flashed on the bottom of the metal crucible and the infrared ray irradiated from the same bottom surface is measured for obtaining the temperature decay, from which the thennal diffusivity of the liquid sample can be estimated. The usefulness and validity of this new laser flash technique have been confirmed by obtaining the thermal diffusivity values of silicate melts in the wide temperature range between 773 and 1673 K.

Jan 1, 2003