Search Documents

By Chen Song

Keywords: Mixed extractant, Copper, Cobalt, Nickel, Synergistic effect During separation process of copper and cobalt from nickel sulphate solution, the effects of constitutions and compositions of mixed extractant D2EHPA and PC88-A or Cyanex 272, has been studied. In one step extraction cycle, the following results are obtained:[Ni]/[Co]>4000 and [Ni]/[Cu]>40000 in nickel sulphate solution, [Co]/[Ni]>1000 and [Co]/[Cu]>30000 in cobalt chlorinate solution, [Cu]/[Ni]>10000 and [Cu]/[Co]>200 in copper sulphate solution. It was elucidated that the above-mentioned synergistic mixtures can effectively separate cobalt and copper from nickel sulphate acid solution and achieve a greater synergistic effect.

Jan 1, 2005

By Ji-He Wei

Keywords: stainless steel, AOD refining, side and top combined blowing, mixing characteristics, water modeling The fluid mixing characteristics in the bath during the side and top combined blowing AOD (argon-oxygen decarburization) refining process of stainless steel have preliminarily been investigated on a water model unit of a 120 t AOD converter. The geometric similarity ratio between the model and its prototype (including the side tuyeres and the top lances) was 1:4. On the basis of the theoretical calculations for the parameters of the gas streams in the side tuyeres and the top lances, the gas blowing rates used for the model have more reasonably been determined. The influence of the tuyere number and position arrangement, and the gas flow rates for side and top blowing on the characteristics has been examined. The results demonstrated that the liquid in the bath underwent vigorous circulatory motion during gas blowing, without obvious dead zone in the bath, resulting in a well mixing effectiveness. The gas flow rate of the main tuyere had a governing role on the characteristics, a suitable increase in the gas flow rate of the subtuyere could improve mixing efficiency, and the gas jet from top lance could make the mixing time prolong. Corresponding to the oxygen top blowing rate specified by the technology, a roughly equivalent and good mixing effectiveness could be reached by using six side tuyeres with an angle of 27 degrees between each tuyere, and five side tuyeres with an angular separation of 22.5 or 27 degrees between each tuyere. The relationships of the mixing time with the gas blowing rates of main-tuyeres and sub-tuyeres and top lance, the angle between each tuyere, and the tuyere number have been obtained.

Jan 1, 2005

By Emma Arakelova

An increase in concentration of a Zn-containing volatile complex for synthesis of ZnO films was investigated when processing their target by ultraviolet radiation emitted by mercury lamp. The experiments were carried out using a flow-type quartz reactor. ZnO tableted target was preliminarily irradiated during 2 to 7 hours. H2O2 (98%) vapor at 25Pa passed through the reactor with ZnO target at 373K. As substrate material, five subsequent quartz cylinders were used at 423K. The experiment lasts 4 hours. H2O2 decomposition on ZnO surface was accompanied by formation of a Zn-containing volatile complex which passed in gas phase and decomposed on the substrates with isolation of final ZnO. The concentration of the Zn-containing volatile complex (N) in gas phase increases with UV pre-irradiation time (t) (without irradiation N = 1.05 1011 particles/cm3; after t=2 hours, N = 5.19 1011 particles/cm3, after t=4 hours, N = 9.95 1011 particles/cm3; after t=7 hours, N = 1.86 1012 particles/cm3.

Jan 1, 2006

By Luciano R. G. Santos

Keywords: biosorption, cadmium, copper, biomass, spent zeolite. The majority of the industrial activities produce some kind of solid wastes. In this work two industrial residues (spent zeolite and wood sawdust) were chemically modified to increase their heavy metals sorption capacities. Manilkara longifolia (a Brazilian plant known as parajú) sawdust was first treated with NaOH and modified with different citric acid concentrations (0.6-1.2 mol/L) at 120°C, for 90 min. Infrared spectroscopy confirmed the presence of carboxylate groups in the wood structure as result of their mixing. Similarly, spent zeolites were also submitted to a chemical treatment (NaOH) to remove carbon deposited during oil cracking and to recover its sorption capacity. Batch experiments carried out at ambient temperature showed that both materials present sorption capacity for copper and cadmium comparable to weak acid ion exchange resins. A maximum of 78 mg-Cd/g and 59.7 mg-Cu/g as well as 29.9 mg-Cd/g and 14.6 mg-Cu/g were observed for the sawdust and the zeolite, respectively. The results were modeled according to the Freundlich and Langmuir equilibrium isotherms and compared with results of other studies.

Jan 1, 2005

By Fang Wu

The paper designs an extraction flow for the total recovery of nickel and cobalt and removing magnesium simultaneously from the cadthodic materials of the spent hydrogen-nickel and cadmium-nickel batteries. The separation of Co, Ni and Mg though P507 extraction .The extraction equilibrium pH is 4.5~5.0, ßNi/Co is 140~180, and ß Ni/Mg is 20~25; nickel and magnesium are scrubbed in two steps, in which the equilibrium pH of nickel and magnesium scrubbing is controlled at 5.0±0.1 and 4.4±0.1 respectively. The stepwise scrubbing technique is adopted to remove 94.5% of magnesium and to recover 99.45% of nickel and 95.35% of cobalt. During the integrated extraction and precipitation process the total recovery fraction of nickel and cobalt are 99.99% and 99.95%, and the recovery fraction of magnesium is 94.02%.The recovered NiSO4 and CoSO4 solution are enriched and crystallized.

Jan 1, 2009

By Holger Cordes

X-ray diffraction has long been used for qualitative and quantitative mineral analysis but Rietveld data analysis is still an under utilized method for mineral exploration and processing applications. In this full-profile approach the structural parameters of each mineral phase, together with experimental parameters, are refined by least-squares methods to minimize the difference between observed and calculated diffraction patterns. The result is a standard-less, quantitative analysis of the mineral abundance in the sample that is more accurate and considerably faster compared to traditional methods. The TOPAS software package combines a user-friendly interface with a unique approach to resolve overlapping peaks. Automated analysis options are also available and significantly reduce analysis time for routine samples. Several examples on a wide range of naturally occurring rock types are shown that illustrate the capabilities and limitations of the method. The examples include several options for the quantification of amorphous constituents like volcanic glasses.

Jan 1, 2006

By Viviane Tavares

The liquid crystal display (LCD) are currently known by its vast application in electro ? electronic devices, amongst them can be detached the devices of TV, laptops, electronic date, calculators and even though the mobile telephones (mobiles). The mobiles are changed more frequent of the TV for example, this happens due to the technology advance. With the constantly mobile exchange, the batteries, printed circuit board and liquid crystal display accumulation its become an environmental problem. To minimize the environmental impacts caused by mobile telephones residues are considered the segregation process of the LCDs main components, to goal to recover the recycle material. This process involves the use of treatment ore techniques with disc, hammers and balls mills. The process with best efficiency (about 98%) of LCD glass release was the hammers mill. The glass recovered can be used in the glass recycling and the sand substitution in the production of concrete blocks.

Jan 1, 2009

By Juliana Gutiérrez-Paredes

Keywords: Slag, chromium oxide, recovery, stainless steel Experimental and theoretical work was performed to estimate the effect of slag basicity and amount of reducing agents on the reduction of chromium oxide from the slag which interacted with molten steel at 1600°C. The slag system contained CaO, MgO, SiO2, CaF2 and Cr2O3 together with Fe-alloys (Fe-Si and Fe-Si-Mg). The CaF2 and MgO contents in the slags were 10 mass % each; Cr2O3 was 25%. The amount of the ferroalloys ranged from 12.5 to 50 g per 100 g of slag. The (CaO+MgO)/SiO2 ratio was held at 1 and 2. The Cr yield was determined using both Fe-alloys as reducing agents. Some estimations were made to determine the theoretical effect of temperature, slag basicity, (CaO+MgO)/SiO2, and amount of reducing agents in the slag on the chromium recovery. The FACT (Facility for the Analysis of Chemical Thermodynamics) computational package is used to determine the equilibrium between the slag and molten steel.

Jan 1, 2005

By A. Deepatana

Bioleaching of nickel laterite ores is based on the use of heterotrophic fungi organisms and their metabolites (organic acids) to dissolve nickel and cobalt from oxide minerals to form metal-organic complexes. Metal recovery from this process using an aminophosphonic acid based chelating resin (Purolite S950) was investigated as a function of metal concentrations, complexing agent including citric, dL-malic and lactic acids. Batch adsorptions were conducted using synthetic leachate solutions of nickel and cobalt with concentrations from 15 to 2000 mg/L prepared in 0.01 and 0.1 M organic acids. Adsorption equilibrium data were interpreted using the Langmuir, Freundlich and Dubinin-Kagner-Radushkevich (DKR) models. The results showed that equilibrium adsorption data for nickel-organic complexes followed the Freundlich model and those for cobalt agreed with the Langmuir model. It was observed that the maximum adsorption capacities of nickel and cobalt were 3.26 and 10.48 mg/g resins respectively. These were achieved in metal complexes prepared from 0.01 M lactic acid. Metal elution was conducted using 2 M nitric acid. High metal recoveries were achieved from low metal concentrations but were found to decrease with increasing metal concentration. The results suggest that effective recovery of nickel and cobalt from low concentration of metals, such as those generated from bioleaching operations, can be achieved suitably using chelating resins.

Jan 1, 2006

By Kim Fagerlund

Boliden Harjavalta Oy operates a copper smelter in Finland, which is based on flash smelting together with Peirce-Smith converting of copper matte. This paper reviews a case study when a high arsenic feed mixture was successfully eliminated in order to guarantee the anode quality. Based on theoretical and practical knowledge in slag chemistry at Outokumpu Research, the CaO-fluxing practice was introduced. Description of a thermodynamic simulation using MTDATA and implementation of the results into converting practice is given. Results showed that the impurity fluctuations in raw materials could be effectively controlled by efficient utilization of different slag chemistry.

Jan 1, 2005

By Xiaowen Liu

The thermal decomposition of diaspore was investigated by thermogravimetry (TG),differential scanning calorimetry (DSC), X-ray power diffraction(XRD),infrared (IR)spectrain this paper. The thermal decomposition mechanism of diaspore was discussed according to Coat-Redfer equation. It was found that the decomposition of diaspore was carried out at 500?,and the peak temperature was 530?. The electrovalent balance of diaspore was destroyed. The previous crystal structure was changed. a- Al2O3 was obtained after thermal decomposition. The activation energy is 287KJ/mol.

Jan 1, 2006

By Valery M. Paretsky

The effect of the degree of nickel oxide reduction and the reaction gas composition on the furnace productivity has been estimated by computations and the established relationship is in good agreement with the practical data obtained in the process of electric smelting at the Severonickel smelter. An increase in the reduction degree within a range of =0.65 - 0.9 results in an increase in the furnace productivity by 19% to 37% and in a decrease in the unit electric power requirement by 16% to 27% depending on the reaction gas composition. The agreement between the computed and practical data has confirmed that the decisive factor for the process of treatment of reduced nickel oxide in an electric-arc furnace under the given conditions is the specific heat absorption, which is dependent on the nickel oxide reduction degree and the reaction gas composition.

Jan 1, 2005

By Jukka Tuominen

The history of making blister copper in an Outokumpu Flash Smelting Furnace dates back to the late 1960?s, when Outokumpu first piloted the Outokumpu Direct Blister (ODB) process. The first commercial scale applications have been in use at Glogow, Poland, since 1978 and at Olympic Dam, Australia, since 1988. These applications utilize special concentrates, which are low in iron, and thus the formation of slag is also low. In 1995 the same principle was applied to smelting copper matte into blister copper in industrial scale at Kennecott Utah Copper. This application, the Kennecott-Outokumpu Flash Converting process, will celebrate its 10th anniversary of commercial scale operation this year. This paper outlines the development in efficiency and flexibility of Blister Flash Smelting processes compared to other smelting and converting options. The focus is on the economical aspects i.e. on the total feasibility of both greenfield investment projects and revamping of existing smelters.

Jan 1, 2005

The purpose of this study was to investigate the immobilization as a host for metallic pollutants (Cr, Cu, Pb, and Zn) by ettringite phase. Ettringite phase is produced through hydration reaction of calcium aluminate with gypsum. From the XRD patterns, it is known that the distance between spaces in 010 planes in ettringite crystal increase with an increase of ionic radius of heavy metal except Pb; no big difference is shown. For this reason, the d-value of 010 planes in ettringite crystal increased with the substitution of Cr, Cu and Zn having a big Al ironic radius. But in case of Pb, because the substitution occurred at calcium site, it does not influence to increase d-value of 010 planes.

Jan 1, 2006

By Muammer Kaya

The purpose of this review is to raise awareness about e-waste problem in the World. Whether generated at our home or our office, e-waste is most rapidly growing waste problem in the world. Even though there are conventional disposal methods (such as landfill and incineration) for e-waste, these methods have both economic and environmental disadvantages; recycling is a new waste management option which diverts end-of-life (EOL) electrical and electronic equipment (EEE) from landfill and incineration [1, 2]. Successful diversion strategy must be based on economic sustainability, technical feasibility and social support [3]. Recycling infrastructure includes transportation, collection, recovery and resale establishments. The first part of this paper describes the e-waste facts, how big is the e-waste problem and existing recycling programmes and collecting methods in the USA and EU; second part, describes various methods available to recover valuable materials (glass, plastic and metals (Pb, Cu, Al, Steel, Ni, Au, Pd, Cu etc)) in e-waste for a safe and environmental friendly disposal

Jan 1, 2009

By David Arana

The use of gas-water dispersion of a molten material flow onto a vibrating surface is developed as a process to minimize water pumping requirements, minimize the risks of explosions, and minimize the post solidification dewatering and fines handling equipment requirements. The process uses existing vibration transport technologies and common plant utilities. Plant trials using the smaller footprint and the progressive molten particle cooling time have yielded encouraging results. The results are analyzed and reported.

Jan 1, 2006

By K. Narayana Swamy

The traditional approach to improving the operating efficiency of a metallurgical plant has been to study individual unit operations and focus on improving the poor-performing unit operations. The complex nature of most metallurgical plants call for a holistic approach that will consider the whole rather than just focus on the individual units of a plant. This holistic approach is part of the systems thinking principles. Numerous case studies highlight the importance of the need to apply systems thinking principles in improving the effectiveness of metallurgical operations. Improving the efficiency of one unit operation without considering its effect on the performance of other unit operations has in many cases lead to lower overall operational efficiency. Modeling and simulation are key to the application of the systems thinking principles. Standard flowsheet models are very useful in scenario analyses though they have to be supplemented with other models for useful predictions.

Jan 1, 2006

By Wilson Acchar

The accelerated growth of urbanization processes and current environmental concerns brought to light the existing enormous quantity of construction and demolition waste (C&DW). Considering the frequent lack of adequate landfill areas available for the disposal of these materials, their use in the manufacture of ceramic products has been attracting a growing interest from researchers and is becoming common practice, with the consequent relief in public administration concerns for the C&DW appropriate management. This work describes the study of clay-based products added with C&DW collected directly from the construction industry. Samples containing up to 50 wt.% C&DW were uniaxially pressed and sintered in air in an electric furnace (950-1150 °C, 1 hour). Sintered test pieces were characterized by X-ray diffraction, apparent density, open porosity and flexural strength. The results showed that up to 50 wt.% C&DW can be added to the clay material, with no degradation in the final product properties.

Jan 1, 2009

By Nam-Il Um

Bottom ash contains several ferrous materials (ferrous metals, Fe3O4, Fe2O3, FeS, etc.). In particular, ferrous metals contain heavy metal because Ni and Cr are chemically attracted to iron. Likewise, Cu is used to coat Ni and Cr metals as polish or to prevent corrosion. In this study, an Fe3O4-Fe2O3 double layer (similar to pure Fe) was found to have been formed in ferrous metal during air-annealing in an incinerator (1000°C). A strong thermal shock such as one that occurs during the water-cooling of bottom ash results in the breakdown of this oxidation layer, facilitating the degradation of ferrous metals and formation of corrosion products. Therefore, Fe-ion (heavy metal) oxides may be formed on ferrous metals and may be separated from bottom ash via magnetic separation. This study sought to investigate the separation ratio of heavy metals as magnetic separation and mineralogical formation of Fe-ion (heavy metal).

Jan 1, 2006

By Jacques J. Eksteen

Metallurgical accounting around toll treatment smelters pose a number of challenges. This paper reviews the requirements for good sampling practice, and how conflicting requirements for good furnace operation and design often makes reliable closure of the metallurgical balance tenuous at best. Typical physical causes of variance and bias will be identified. The propagation of error (in the form of variance) will be discussed for a copper smelter.

Jan 1, 2006