Search Documents

By E. F. Vegman, Ndabezinhle Dube

"In the practice of conventional sintering, production is always afflicted with the problem of being unable to get a uniform quality of produced sinter in the bed. Invariably the top layer of the sinter cake is composed of weak but highly sinter, while the bottom layer is over-fused, forming a sinter that is very strong but less reducible. These symptoms point to a variable distribution of the heat balance in the process of sintering which results in a deficit of heat in the top layers of the sinter bed and an excess of heat in the bottom layers, due to an increasing input of regenerated heat in the heat balance down the bed. This causes losses in the productivities of the sinter machine and the blast furnace.The current work was designed to improve on the solution to the above problem through the establishment of a more accurate combustion zone heat balance of the sintering process. This development is mostly on the method of determining the regenerated heat input in the overall heat balance. Previous methods were based on the assumption that the width and the velocity of the combustion zone remain constant through out its whole life, which is not the case since tests have shown that both its width and velocity increase as the combustion zone moves down the bed. In this work, these factors have been taken into account. Tests and calculations using the model were carried out for haematite and limonitic ores. The high sensitivity of the model to changes in the sinter mix composition and sintering conditions was demonstrated.The results present the following prospects:• The minimum theoretically possible coke breeze consumption during the sintering of any type of iron ore fines, under any sintering conditions, can be established.• The model can be used to control the metallurgical quality of the sinter in any point in the sinter bed since calculation data includes desired basicity, combustion zone temperature and FeO content in the sinter produced."

Jan 1, 2001

By B. C. Jena

Activities of carbon, cobalt and nickel were evaluated in the ternary systems iron-carbon-cobalt and iron-carbon-nickel for the temperature range 1300-1600°C for cobalt and 1300-1700°C for nickel. The carbon activities were determined from the knowledge of activities (1) in the binary system iron-carbon, (2) in the dilute ternary systems and (3) from the knowledge of carbon saturation data. The activities were mathematically expressed with the Taylor series expansion of Wagner's interaction parameter formalism modified to suit concentrated solutions. The cobalt and nickel activities were determined from the knowledge of carbon activities by applying the Gibbs-Schuhmann integration and from cobalt and nickel activities in the binary systems iron-cobalt and iron-nickel. Partial molar enthalpies of mixing were determined based on the temperature behaviour of the activity coefficients.

Jan 1, 1992

By L. M. Abrantes, A. P. Paiva

"A brief review of some innovative methods for the direct recovery of metals from loaded organic phases is presented; emphasis is given to electroreductive stripping and cementation, which are described and illustrated by examples: of current research. The recovery of silver using a two-phase electrolysis - by direct application of an electrical potential to a mixture of a metal loaded organic phase· containing Cyanex 471X, obtained by solvent extraction, and a stabilized sodium thiosulfate solution - is more extensively discussed. The overall efficiencies are analyzed and compared with data obtained by conventional stripping procedures. Some preliminary results achieved for the recovery of the precious metal using galvanic stripping, applied directly to similar organic solutions and involving zinc and iron powders as reducing agents, are also evaluated.Introductory ReviewThe application of hydrometallurgical methods to the recovery of metal values from ores and concentrates has been receiving a growing interest, either from researchers or from the mining industry [1].For the concentration / purification of the relatively low concentrated metallic solutions resulting from the leaching of those raw materials, solvent extraction (SX) is a well established technique [2]; the loaded organic solvent is then conventionally contacted with a suitable aqueous solution, the metal in its final form being usually recovered from this solution by electrowinning.As an efficient and / or selective stripping is sometimes difficult to achieve, depending on the specific characteristics of the system under consideration, some alternative procedures have been analyzed in order to overcome this problem. One of the chosen routes, mainly developed by Hirai and Komasawa, is to promote the reduction of the desired metal species in the organic phase, in such a way that the stripping stage becomes feasible; for the selective stripping of vanadium from a solvent containing a mixture of vanadium and molybdenum, the authors successfully used reductive [3], electro-reductive [4,5] and photo-reductive [6] techniques. The two latter methodologies have also been applied to the recovery of europium from a solvent containing europium, samarium and gadolinium [7,8].However, further processing is necessary to recover the metal in its solid state; therefore, methods causing the direct reduction of the metal species in the organic phase to their fmal metallic form would be of interest, as an intermediate step would be avoided"

Jan 1, 1997

By Tom Lewis

The metal finishing and electronic industries are searching for ways to recycle materials · and reduce costs. The areas of heavy metal waste and water recycling has gained new interests with the potential of impacting the operation's bottom line. Lewis Environmental Services, Inc. has completed numerous heavy metal recovery and effluent recycling projects with its ENVIRO-CLEAN PROCESS for government and private sector clients. This patented process utilizes a proprietary chemically treated granular activated carbon with enhanced heavy metal adsorption capabilities combined with electrolytic metal recovery to produce a saleable metallic product. The process generates no sludge or hazardous waste and the effluent meets EPA .limits. This paper covers several heavy metal removal projects, two fullcscale commercial installations, and one treatability case study.

Jan 1, 2000

By William Petruk

An investigation was conducted to determine whether mineral liberation data obtained by one image analysis technique are the same as data obtained by another image analysis technique. The liberated vs non-liberated, volume % and weight % techniques for measuring mineral liberations by image analysis were tested. The results show significant differences between the values obtained by the different techniques. The lowest liberation values were obtained by the liberated vs non-liberated technique and highest by the weight % technique. It is interpreted that the weight % technique produces the most realistic results. The weight % technique also produces data that can define mineral associations for the unliberated grains. These include (1) mineral quantities in particles that contain different amounts of unliberated mineral, (2) mineral quantities in particles that have different size ranges, and (3) mineral quantities and degrees of liberation for specific minerals in particles of different size ranges.

Jan 1, 1996

By G. Coryell, S. Blaskovich

"A computer model has been developed to simulate the flash furnace and converter operations at the ASARCO Hayden Copper Smelter. The focus of the modeling was to optimize the converter operation to eliminate high matte level episodes in the flash furnace. These episodes (reducing feed to the furnace) resulted from the lack of converter operation scheduling. The model provided ""what if?"" scheduling scenarios that led to increased efficiency of the converter and flash furnace operations.This paper discusses alternatives studied to optimize the converter operation and the development of the computer modeling program, including implementation of the project. The discussion details the results of the project including the conversion from batch to a real time converter scheduling process. IntroductionASARCO's Hayden Smelter consists of a fluid bed drying system, an Inco oxygen flash smelting furnace, Peirce Smith converters, two anode furnaces and two casting wheels, gas cleaning plant, 2800 stpd sulfuric acid plant, 650 stpd oxygen plant and 200 gpm water treatment plant. The process flow sheet of the plant is shown in Figure 1.Over the past several years, the Hayden smelter has been involved in productivity improvement and cost reduction programs. This has been necessary to become a low cost copper producer in today's market. Part of the productivity improvement program was the use of process control to streamline the flash furnace and converter operations. Process control, through the use of computers and electronic controllers, has played an increasingly important role in optimizing processes in the Hayden Plant since the startup of the Inco flash furnace in 1983."

Jan 1, 1989

By Wenxian Zhu, Xuema Li, Patrick R. Taylor

"Experiments were performed in a non-transferred arc, thermal plasma flow reactor to investigate the synthesis of ultra fine boron nitride (BN) powder from the reaction system of boron oxide (Bz03), methane (CH4), ammonia (NH3) and hydrogen (H2). Argon (Ar) and nitrogen (N2) were used as plasma gases. The thermodynamics and kinetics of the synthesis reactions were examined and a chemical reaction mechanism was proposed. The powders produced under certain operating conditions had high purity and good conversions. All the products were extremely fine powders (< 30nm) and were uniform in size distribution. The powder products were analyzed by chemical and physical characterization. The effects of the reaction variables on the conversions from B203 to BN and the purity of the products were investigated.IntroductionIn the past few decades, boron nitride (BN) has attracted a great deal of interest because of its excellent thermal, chemical and electrical properties (1-4) It has a high thermal stability and thermal conductivity. Chemically, it is very stable and is not wetted by most molten metals and slag. It is also an excellent low loss insulator. Since hexagonal boron nitride (h-BN) is light in weight, strong and easily fabricated, it has applications in a variety of specialized high temperature areas, such as a high temperature lubricant, crucibles for molten metals, thermocouple protection tubes, break rings for horizontal continuous casting of steel, and friction reducing coatings. In cubic form, boron nitride is one of the hardest materials known, second only to diamond, and it is an excellent material for tools in which the use of carbon based materials is limited by oxidation or reaction with metals."

Jan 1, 1998

By Pekka Taskinen

The converter-less nickel matte smelting technology (DON) adopted more than 20 years ago in Boliden Harjavalta smelter has been since that applied successfully to the processing of large number of nickel sulphide concentrates of various Ni-to-Cu ratios and MgO contents. The operational point of the technology is far from the conventional primary nickel smelting in the smelting-converting route. Therefore, a careful scouting of distribution equilibria of the base and trace elements in the smelting conditions of DON process has been conducted, in order to obtain quantitative information about the equilibria and thermodynamic properties of the nickel mattes at low iron concentrations, less than 10 wt% [Fe] in matte. The series of investigations has included novel experimental and analytical techniques for increasing the reliability and sensitivity of the phase equilibria as well as the element distribution observations carried out in typical high-grade nickel matte smelting conditions.

By Tuula Mäkinen

One of the latest applications of the Outokumpu Flash Smelting Technology is the direct smelting ,of nickel concentrates to metallised low-iron nickel mattes. Compared to the conventional nickel smelting, the new DON process needs a lower number of smelting vessels resulting in considerable economic and environmental benefits. Fundamentals of smelting nickel concentrates in one stage to low-iron mattes are presented. Properties of nickel. smelting slags with an emphasis of the slag fluidity at high MgO-levels are also discussed. Conditions prevailing in DON mattes at high oxidation degrees are presented as well as their influence on the behaviour of such mattes in the settler and on tapping the furnace. Distributions of elements in the direct smelting are presented and compared with the conventional process. A further comparison is made with pilot-plant data and the industrial scale.

Jan 1, 1998

By E. Allain

Extraction of basic metals from sulfides by conventional pyrometallurgical processing leads to the emission of SO2. To avoid this inconvenient, low temperature selective chlorination of sulfide concentrates could be an alternative. However, such process generates hazardous chlorides SxCly. A part of sulfur chlorides such as SCI2 can be recycled as a chlorinating agent of metal sulfides. Hydrolysis of sulfur chlorides, using a solution containing Na2S.9H2O, led to the recovery of more than 90 pct of elemental sulfur. Reduction of SxCly by hydrogen was investigated between 300 °C and 800 °C. About 70 and 90 pct of elemental sulfur were recovered from SC12 and S2C12, respectively. A flow sheet for the chlorination of metal sulfides and the treatment of sulfur chlorides was suggested.

Jan 1, 1998

By I. M. Richardson, M. Janssen, I. J. Bennett, V. A. Popovich

The most critical processing step during the manufacture of screen-printed crystalline solar cells is firing aluminium and silver contacts, which generates residual stresses and solar cell bowing. In this paper, an alternative Ag contact formation mechanism is proposed and aspects related to electrical contact properties, residual stresses and layer delamination are investigated. It is found that there are two main processing parameters affecting the uniformity and delamination of the Ag/Si interface, namely the peak firing temperature and the silicon surface roughness. Silicon surface polishing gives a better wetting of the silicon surface by the glass layer, resulting in a good contact and lower incidence of large voids, compared to the case of highly textured surfaces. The non-uniformity in the glass layer and large voids at the Ag/Si interface (in the case of a textured surface) are expected to have a negative effect on the mechanical strength of the solar cell.

Jan 1, 2015

By Mansoor Barati

The present paper is based on a term project for final year undergraduate students, requiring them to evaluate a process for producing silicon from rice husk. The traditional method for production of silicon involves carbothermal reduction of quartz in electric arc furnaces at temperatures exceeding 2000 °C. The technology consumes a considerable amount of electrical energy as well as fossil fuels, resulting in significant CO2 emissions. A flowsheet for production of silicon metal from rice husk is laid out in this paper. The technology will consist of combustors, which will generate steam using the rice husk biomass, power generator, and electric furnace for reduction of the rice husk. Materials and energy balance calculations presented here indicate that such process can be operated independent of external electricity.

Jan 1, 2014

By Wang Jingsong, Ma Tengfei, Feng Fu, She Xuefeng

In this paper the direct reduction melting separation-leaching process is investigated on recovering rare earth from rare earth Bayan Obo complex iron ore (REBOCIO). The REBOCIO was reduced and melting separated to produce iron nugget and rare-earth-rich slag at 1400°C for 12 or 15 min. The RE2O3 is enriched into Ce 4.667(SiO4)O or Ca 3Ce2[(Si,P)3O4]3F, which closely depend on chemical components, especially basic. The optimal acid-leaching parameters of rare earth elements from the rare earth slag are suggested as the hydrochloric acid concentration, the ratio of solid to liquid, leaching temperature, and the leaching time are 1 mol/L, 1:14, 50 °C and 120 min, respectively. The rare earth elements leaching efficiency are more than 95%. Adding of calcium CaCO3 and sodium Na2CO3 in direct reduction process have great in fluence on leaching ef ficiency of thorium.

Mar 1, 2018

By J. D. McCain

Magma&apos;s San Manuel smelter has adopted new operating techniques resulting in 21% increased productivity and 87% reduction in lost time accidents. Reverberatory furnaces were converted to coal firing from expensive natural gas and fuel oil. Slag and matte flow problems and safety were improved by implementing hydraulic slag stopping and matte tapping machines. Coordination of furnaces, converters and acid plant was improved by using a computer-aided converter controller/scheduler function. Manual mudding of converter lips after each collar pull was replaced with a gunning system for coating the mouth castings. One converter punch car was automated using robotic technology. An automatic anode take-off was installed with fewer moving parts and a mechanism for ear twisting one cell contact. Anode copper refining was improved by replacing propane/hydrogen mixtures with high pressure/velocity natural gas tuyeres. Improved converter scheduling increased acid plant production 43% with more autothermal operation time. Six dedicated computers/microprocessors are utilized for automation, data acquisition, process monitoring and on-line air quality information for the Supplementary Control System.

Jan 1, 1983

During electrowinning of nickel chloride, hydrochloric acid was regenerated instead of chlorine in a two membrane cell, by segregating the chloride catholyte with an anion exchange membrane, and the sulphate anolyte with a cation exchange membrane from the middle electrolyte (ampholyte) compartment. Successful operation of such a cell depends on controlling chloride leakage through the cation exchange membrane to the anolyte. Small amounts of chlorine gas could be detected in the oxygen evolved at the anode. In this paper, the chloride. leakage as a function of various types of cation exchange membrane and different composition of the anolyte is reported and discussed. Ag+ was added to the anolyte to eliminate chloride leakage to the anode. The cell voltage, electrode potential and voltage drop over the membrane as a function of current density has also been investigated.

Jan 1, 1996

By John R. Howell

"SUMMARYThe process of producing a new cast component requires significant design and development by both the design engineer and the foundry engineer. This effort strives to produce a high quality component at minimum cost. To assist in this development, an analysis system, consisting of several computer programs, has been developed to simulate the metal casting process. This system incorporates analytical geometric solid modeling, finite element analysis, results display, and an innovative technique to model the casting mold with surface boundary conditions.The simulation has produced excellent thermal results and work is in progress to develop techniques to enable use of this data in additional analyses to predict porosity and residual stress. Research is required to produce working parametric formulations of material properties. Software development is required to develop good fluid flow analyses for large. 3D models to simulate filling of and convection in molds.Integrating this system of programs is difficult due to proprietary database structures used by software developers. However, an acceptable means has been accomplished' to move data from one program to another. Further software development is required to facilitate this task. INTRODUCTIONThe process of producing a new cast component requires significant design and development by both the design and foundry engineer. This effort strives to produce a high quality, reliable component at minimum cost in a timely manner. The design engineer needs to know the physical and mechanical properites which can be expected in the actual part at critical areas. This will enable him to design a part with minimum material while fulfilling the performance required. The foundry engineer needs to produce a sound, quality casting with a minimal amount of material In risers, the feeding system and machining stock. This must be done with a minimum· investment in tooling and development time and maximum productivity of labor and capital employed. This task Is continually being made more difficult because of increased competition in the marketplace and the use of castings in more severe service. This has strongly influenced the need for high quality castings.The task of developing a new casting is difficult for both the design and foundry engineer. To assist in this development, Deere & Company has been engaged in the development of an analysis system to simulate material processes. A major portion of this program involves simulation of the metal casting process. This analysis system has evolved into a package of computer programs which simulates casting solidification and subsequent cooling through the finite element method"

Jan 1, 1986

By Jilai Xue, Jun Zhu, Germain Kouma Ndong, Qiaochu Liu, Luxing Feng

"High-temperature oxidation and corrosion behaviors of Ni-Fe-Cr alloy as inert anodes for aluminum electrolysis have been studied in oxygen and molten electrolyte. The oxidation and corrosion scales on the anodes tested were analyzed using XRD and SEM-EDS. The oxidation rate is found to increase with increasing temperature from 700 °C to 950 °C, which can be approximately described by an inverse power rate function. The oxidation scales at 750 °C, 920 °C and 950 °C contain Cr-rich phase along with FeCr204 and (Feo.6Cro4)203. The corrosion extent of Ni-Fe-Cr anodes in electrolyte is dominated by temperature, which can make the scales thickness double from 700 °C to 750 °C or from 920 °C to 950 °C. Cr and Fe in the scales on the anode in electrolysis corrode preferentially into the molten electrolyte, while the nickel oxides could better sustain the corrosive environment in electrolysis. The results can be useful for developing inert anode material for potential application in aluminum electrolysis.IntroductionThe development of an inert anode for aluminum electrolysis has been a long term goal for aluminum industry. The present process for primary aluminum production involves the reduction of alumina with carbon anodes, forming carbon dioxide:"

Jan 1, 2013

By Yoji Imai, Akio Watanabe, Masakazu Mukaida

"To clarify the feasibility of alkoxides and acetylacetonates as precursors for laser CVD of metal oxides, vapors of tantalum or titanium alkoxides and zirconium acetylacetonate were irradiated by KrF excimer laser and deposits were characterized by XRD and XPS measurements. As for tantalum and titanium, non-stoichiometric crystalline oxides grew nearly phototropically, however, zirconium oxides deposited showed only halo-pattern by XRD measurements. Electric conductivity measurements of tantalum oxides implied the improvement of the insulating properties by the addition of activated oxygen to the ambient.IntroductionThere has been renewed increasing attention to the metallic oxide thin films because ofits promising usefulness in many applications, such as high-Tc superconductors and ferroelectric devices. A variety of thin film preparation techniques have been studied such as sputtering, chemical liquid deposition (sol-gel and metalorganic decomposition), pulsed laser deposition and chemical vapor deposition (CVD). Among them, we think CVD is the most promising method because it offers a high controllability of morphology and good step coverage at relatively high growth rate. Preparation of oxide films by CVD can be achieved using a precursor containing metallic element and oxygen containing gas such as N20 at the same time. However, metalorganic (MO) compounds which contain both metallic element and oxygen, directly bonded to metallic element, seems to be more favorable because some of MO has a good properties for CVD such as a rather high vapor pressure, stability in ambient and low toxicity."

Jan 1, 1998

By R. Kola

Since more than 15 years the Waelz process at "Berzelius" in Duisburg has proved suitable for reprocessing the zinc and lead containing dust and .sludge which inevitably occur in making steel in EAF-plants. The produced Waelz-oxide is agglomerated in a hot-briquetting plant and charged to an Imperial Smelting Shaft Furnace to recover the valuable elements in form of metallic zinc and lead. In view of the actual importance of the dumping problems of the EAF wastes a description of the "Berzelius" treatment route is given but also the situation in Western Europe is illustrated. Dust from stainless steel production is successfully treated in the Scan Dust Plasma Process in order to recycle Chromium and Nickel, while the resulting Zinc-Dust is treated via the Waelz-ISF-Route. For treatment of low Zinc-containing dust, sludge and fines from integrated steelworks, pilot scale tests have been carried out successfully in the Circulating Fluid Bed in order to recover metalized iron and .zinc/lead fume. A 30,000 tpy Demonstration Plant is planned?.

Jan 1, 1990

By Glenn Stevens

After 40 years of operation with the original design, Pan Pacific Copper determined it was necessary to rebuild the Saganoseki Flash Smelting Furnace to continue safe operation. The original design employed a rigid steel frame, which, through hearth growth, led to severe distortion of the frame. Contributing to the continued growth of the hearth were thermal cycles that occurred during the government mandated annual shutdowns. Hatch designed a unique sprung bound, pivoting binding frame to maximize crucible size within the existing furnace footprint, while integrating the PPC designed cooling jackets. The bound system maintains tight brick joints, while the new conductive hearth design with integrated bottom cooling produces a protective freeze layer to accommodate higher furnace throughput. Minimization of furnace downtime for the rebuild was achieved through effective construction planning, highly trained contractors, and through an efficient start-up and ramp-up to full production.