Search Documents

By N. B. Gray, I. F. Taylor

"Gas injection to promote chemical reactions or mixing is a feature of many metallurgical processes. Often the aim of gas injection is to bring about a chemical reaction between the gas and liquid but most of the past physical and mathematical modelling work has ignored the influence of such reactions. In the work reported here, cold model studies have been conducted in which gas reacts with the liquid into which it was injected. The rate of liquid mixing has been measured as an indication of the mechanical energy transfer. It has been found that gas generated chemically within the liquid is significantly less effective at promoting mixing than the equivalent volume of inert gas. The relative ineffectiveness of chemically produced gas is thought to be due to smaller bubble sizes in comparison to the inert gas case. Small bubbles characteristic of chemically generated gas move with low slip velocities relative to the liquid and lead to different turbulence generation mechanisms.IntroductionIn processes such as steelmaking, copper conversion, bath smelting and ladle steel finishing gas is injected into liquid metal where it reacts chemically or simply serves as a source of agitation. An understanding of fluid flow phenomena in such situations is an essential pre-requisite to the calculation of process intensity and the optimisation of vessel productivity. Traditional physical cold modelling approaches to prediction of liquid flow in such situations are now often augmented by the techniques of computational fluid dynamics. Even with the availability of numerical modelling techniques cold physical models continue to have an important role for validation because it is generally difficult to obtain quantitative data from high temperature processes.Almost all previous cold modelling work has been based on the injection of an inert gas into water or some other non-reactive liquid. Such models do not include the significant increase in gas volume inherent in some processes. For example the oxidation of carbon in steelmaking leads to a twofold increase in molar gas flux through the reaction:"

Jan 1, 1996

By D. H. H. Quon

Results of a study conducted to determine the properties of iron ore pellets made from Mount Wright and Carol Lake ore concentrate fines with partial and full substitution of bentonite by several organic binders are presented. Carboxy methyl celluloses 7H and 6TL, hydroxy ethyl cellulose (natrosol) and modified guar gum all produce pellets of acceptable wet, green and dry strength. However, when fully substituted, an inorganic binder such as calcium carbonate is required for satisfactory strength development after induration. Mixing the Carol Lake ore with Mount Wright ore in a 50-50 ratio also achieves the same result. The failure of the Carol Lake ore in the pelletization process is attributed to the low hematite content of the ore. The results are very similar to those from the extrusion studies reported earlier (8).

Jan 1, 1989

By J. H. Corrigan

A series of six papers describing the Falconbridge Dominicana Ferronickel project were presented at the International Laterite Symposium held as a joint project of TMS-AIME in February 1979 at New Orleans. A review of the ore mineralogy, as well as. the processing and environmental practices as they exist today at Falcondo with emphasis on modifications put into practice since 1979 are presented in two papers: Part I.- Mineralogy and Ore Dressing E.W. Lithgow - General Superintendent ? Mines Falconbridge Dominicana, C. por A. Bonao, Dominican Republic Commercial volumes of nickeliferous laterite ores overlie part of a 90 km long belt of peridotites in central Dominican Republic. Protores are serpentinized harzburgites and dunites, with lesser serpentinite. The ore mineralogy consists mostly of goethite, serpentine-group minerals, quartz and poorly crystallized, X- ray amorphous materials. Minor constituents are hematite, gibsite, olivine and enstatite. In the Ore Dressing plant, the mine feed is subjected initially to proper sizing and blending to produce a homogenized mix. Subsequent drying and upgrading, by selective crushing and screening of rock kagments through a Barmac circuit, complete preparation of the ore for pyrometallurgical processing. Part II.- Pyrometallurgy, Fuel and Power Generation J.H. Comgan - Manager ? Production Falconbridge Dominicana, C. por A. Bonao, Dominican Republic Falcondo's energy requirements are based on oil which is refined on site to provide distillate to carry out drying and selective reduction of the nickeliferous ore in the shaft furnaces, plus bunker oil to produce electrical power for process melting, refining and ancillary use. The dryer product at 1.68% Ni is briquetted and passed counter current to hot reducing gas in 12 vertical shaft furnaces. The hot calcine discharge is melted in two high power electric furnaces at very high secondary voltage. The crude ferronickel is ladle refined and cast as 15 kg ingots or 125 gm ferrocones.

Jan 1, 1993

By Stanko Nikolic

One of the keys to success in process development is incremental scale-up, allowing for potential problems to be identified and rectified. The ISASMELT™top submerged lance (TSL) process was developed to maturity using this method by Mount Isa Mines, now owned by Glencore. Commercialization only occurred once the process had been proven on each scale and as a result the ISASMELT™ technology now operates successfully around the world. An important parameter in the evolution of the technology has been the furnace campaign life. The initial commercial scale furnaces had minimal water-cooling. Although this led to shorter campaign lives, an extended development program resulted in the achievement of four-year campaign lives, without any water cooling. In tandem to the refractory designs Glencore Technology, supplier of the TSL technology, has progressed cooled copper lining designs for application to both the ISASMELT™ and ISACONVERT™ furnaces allowing for ultimate flexibility in the lining choice. This allows each ISASMELT™ operating site to minimize their overall life-cycle costs by balancing their campaign life with lining costs, energy inputs, and other shutdown requirements.

By Juan Patricio Ibáñez

Separation of arsenic and copper from Cu-As-H2S04 electrolytes by electrodialysis has been investigated at room temperature. The effects of current density and pH were studied. An arsenic-free copper solution was obtained for all the tested conditions. The transport efficiency for copper ions was found to be higher than 98% after 3 hours' test. Transport of arsenic and copper through the ion exchange membranes was increased by increasing pH and current density. Solution pH was found to be a key parameter for the separation process, since it controls the speciation of the ions to be transported and the formation of unwanted precipitates which reduce the global efficiency of the electrodialysis process. The main conclusion is that electrodialysis is a promising technique to be used in separating and/or concentrating ions of interest in copper electrometallurgy.

Jan 1, 2003

By Animesh Jha

The carbothermic reduction of chalcopyrite has been studied in the temperature range 1073 to 1273K in presence of lime. The role of lime during the reduction process is explained and the phase equilibria leading to the metallisation of copper and iron are discussed. The effect of coal and carbon monoxide on the reduction process have been studied and the rate governing steps are identified. This investigation also cites examples of possible mechanisms of physical separation of metallic Cu from iron during the reduction process.

Jan 1, 1992

By J. David Chapman

There are a variety of choices of materials for mineral extraction processing. Traditionally, end users have used metallic piping for fluid handling and little is known about the advantages (or limitations) of non-metallic piping systems. This presentation will review custom FRP pipe systems and their use in severe corrosive and erosive process streams. These systems can be designed to various pressure and temperature ratings and different components (such as resin and glass type) can be varied to suit the process conditions

By Z. Q. Chen, M. H. Loretto, Y. G. Li

"As-cast, As-forged, as-solution-treated, and solution treated and aged microstructures of Ti-15Mo (IMI205) with and without carbon were examined using optical microscopy, scanning electron microscopy .and transmission electron microscopy. Tensile testing was carried out at room temperature. It was found that carbon acts primarily as a titanium carbide former: Titanium carbides increase slightly the tensile strength, but decrease the ductility of IMI205. These observations are interpreted in terms of the titanium carbide morphology observed using SEM and TEM and the phase diagrams of Ti-Mo, Ti-C, and Mo-C.IntroductionIn a recent study on the development of a burn-resistant 13-Ti alloy, carbon was introduced· into the Ti-V-Cr system in order to optimise the mechanical properties. Research results[1, 2] demonstrate that carbon addition can refine the 13 grain size and improve the stability of the 13 phase in Ti-V-Cr alloys. The most attractive result is that carbon addition produced a marked improvement in the ductility of alloys when the carbon content is over 0.1 wt.% in this alloy system. Even after long exposure, the alloy with carbon addition maintains good ductility. One of the main reasons for the ductilising of the alloy is that titanium carbides can getter the oxygen from the 13 matrix.In view of the success of carbon addition in improving the properties and the stability of the Ti-V-Cr alloy, it is of interest to investigate the behaviour of carbon addition in other beta Ti-base alloys. The objective of the present work was, therefore, to assess the microstructures and mechanical properties of IMI 205, a metastable beta titanium alloy, with and without carbon addition using optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM), wavelength dispersive X-ray (WDX) analysis, room temperature tensile testing."

Jan 1, 2000

By T. E. Warner

In order to detect arsenic and antimony in zinc, various electrochemcial experiments were performed involving the electrochemical introduction of sodium atoms into molten zinc using a solid electrolyte. Under high rates, the formation of the intermetallic phase NaZn13 was assumed to form. Under more moderate injection rates of sodium, employing a symmetric "zinc/zinc cell", a qualitative relationship between the current generated during cyclic voltammeuy and the arsenic and antimony concentrations in molten zinc was observed.

Jan 1, 1999

By Takashi Araki

In this work, we have elucidated the two-step oxidative reaction mechanism of 2,4,5-trichlorophenol by adsorbing oxygen atom for oxidative decomposition reaction of 2,4,5-trichlorophenol on oxide catalyst surface using ab initio molecular orbital calculation. In the first oxidation, total energies of reaction products have been shown extremely stabilized at all oxidation positions. This reaction occurs due to charge transfer from benzene ring to adsorbing oxygen atom. As a result, 1£ bonding of benzene ring are weakened. However, the benzene ring of 2,4,5-trichlorophenol does not perform cleavage reaction. In the second oxidation, the benzene ring of2,4,5-trichlorophenol can perform cleavage reaction, since the second oxidation obtains larger stabilized energies than the first oxidation.

Jan 1, 2003

By Yuanbo Zhang, Zhixiong You, Zijian Su, Bingbing Liu, Guanghui Li, Guang Yang, Tao Jiang

Sodium stannate is widely used in the electroplating and tin alloy industry. But the traditional processes for sodium stannate production are characterized by long flowsheet, high production cost and strict requirement for the equipments, etc. In this study, a novel process for sodium stannate preparation from cassiterite concentrate and sodium carbonate via roasting in CO/CO2 mixed gas then followed by leaching was developed. The effects of roasting parameters on the Sn leaching efficiency were conducted. A Sn leaching efficiency of 77.2% was obtained under the optimal conditions. Sodium stannate (Na2SnO3·3H2O) with a purity of 95.8% was produced by the new process, which is better than that specified for the industrial first-grade product.

Jan 1, 2014

By James W. Reeves

DuPont was the titanium metal pioneer who put the greatest effort into both R&D and commercial sponge and powder metallurgy production. This was concentrated in the period 1945 through 1963. The commercial results were development of the chloride process for TiCl4 using ilmenite, development and improvement of the Kroll process, development of a modified Hunter process to make titanium powder and commercial development of a direct powder process. The powder metallurgical process failed because of the inability to meet powder chloride specifications. All this work remained a trade secret until published in NMAB -392 by Mahla in 1983. There were other processes explored by DuPont, both improved sponge and powder processes. Much of this work has been continued by others but none, as of yet, resulting in new improved titanium metal capacity.

Jan 1, 2001

By Tian Sugui

By means of the long-term aging treated, creep properties measuring and microstructure observation, an investigation has been made into the microstructure and creep behavior of the casting and rolling GH4169 superalloy after long-term aged. Results show that, after the casting and rolling GH4169 superalloy treated by long-term aged, significant amount of " phase are dispersedly precipitated within the grains of the alloy, and some of the NbC, Cr7C3 carbide are distributed along the grain boundaries. In the range of the applied stresses and temperatures, the creep activation energies and stress exponents of LTA GH4169 alloy during steady state creep are calculated to be Q=541.1kJ/mol and n=16.2, respectively. During creep, the deformation mechanism of LTA GH4169 is thought to be the twinning and dislocation slipping within the twinning regions, and the damaging mode of the alloy is the intergranular fracture, and the non-smooth crystal surface is displayed in the fracture regions of the alloy. Thereinto, the carbides film formed along the grain boundaies has a few effect on the strength between the boundaries, which is a main reason of resulting in the alloy possessing a longer creep lifetimes.

Jan 1, 2009

By Courtney Young, Jerome Downey

"The various technologies developed for treating spent potlining (SPL) from primary aluminum smelters have been reviewed on several occasions. The technologies generally involve physical, chemical, and thermal processes, either individually or in combination, with the primary objective of total recycle, waste minimization, or complete disposal. In general, those technologies geared for recycling involve separations and are therefore subject to recovery inefficiencies that are attributed to several factors. However, the inefficiencies could be reduced or possibly eliminated if the pots were designed for recyclability. This concept is applied to SPLASH, a recently developed SPL management technology.IntroductionAluminum is produced by molten salt electrolysis via the Hall-Héroult process. The process is conducted in an electrolytic “pot,” which is comprised of a steel frame first lined with insulating refractory brick, and then conductive graphite blocks, which serves as the carbon cathode [1, 2]. These materials are collectively referred to as “potlining.” Anodes comprised of petroleum coke/pitch are suspended above the pot and extend down into the molten cryolite (Na3AlF6) electrolyte. The electrolyte temperature is maintained at approximately 980 °C by resistance heating as low voltage (4-5 volts) and high current (50,000-300,000 amps) are applied across the two electrodes.High purity alumina is added to the cryolite bath, where it dissolves and becomes amenable to aluminum reduction at the cathode:"

Jan 1, 2008

By Kuniaki Murase, Tetsuji Hirato, Koji Nitta, Yasuhiro Awakura

"The redox behavior of copper species in an ""ammonium imide"" room temperature molten salt was examined in order to clarify the applicability of the salt to the electroplating media of various metals. Trimethyl-n-hexylammonium bis(trifluoromethanesulfonyl)- amide (TMHA-Tf2N), having an electrochemical window of 5.6 V (50 °C), and corresponding copper(II) salt were synthesized. In TMHA-Tf2N media monovalent copper ion, Cu(I), was stable and Cu metal was oxidized, or corroded, in the presence of Cu(II) species. Cathodic electrodeposition of copper metal and anodic dissolution of it were, thus, one-electron reaction and their current efficiencies were almost 100%.IntroductionElectrodeposition of metals from aqueous solutions is an important soft process for manufacturing thin-film materials, surface finishing, and extractive metallurgy. However, the electrodeposition of base metals, such as zinc, chromium, and nickel, from aqueous media inevitably accompanies hydrogen evolution, which lowers the cathodic current efficiency of metal deposition. Since the electrodeposition of aluminium, titanium, and rare earths from aqueous media is actually impossible due to their largely negative redox potentials, nonaqueous media such as aprotic organic solvent and high-temperature molten salts have been employed for the electrodeposition of these metals. Room temperature molten salts (RTMS),1, 2) or room temperature ionic liquids, have also been developed as a promising electrolytes for the electrodeposition of base metals. In this field, chloroaluminates of alkylpyridinium or alkylimidazolium cation have been well investigated for aluminium3) or alluminium-alloy4-5) electroplating media. On the other hand, in order to avoid high hygroscopicity arising from the use of aluminium chloride, attempts have been made to combine the alkylimidazolium cations with fluorine-containing hydrophobic anions, e.g. BF4-,6) CF3SO3- (TfO-),7) (CF3SO2)2N- (Tf2N-),8) and H(HF)n-ions,9) and investigated for electrodeposition media.'°) Recently, a new series of RTMS consisting of tetraalkylammonium cations and Tf2N- anion, sometimes abbreviated as TFSI- anion, was found independently by MacFarlane et al.11, 12) and Matsumoto et al. 13) This type of RTMS, which is commonly named ""ammoniumimide"" salt, has a wide electrochemical window of ca. 5 V and, thus, the RTMS seems to be suited for practical application as a solvent for the electrodeposition process. In this paper, we report the electrochemical behavior of copper species in an ammoniumimide RTMS, trimethyl-n-hexylammonium bis(trifluoromethanesulfonyl)amide (TMHA-Tf2N)."

Jan 1, 2000

By Kimiaki Utsunomiya, Yasumasa Hattori, Yoshiaki Mori, Toyokazu Okubo

"The effect of various operating conditions on splashing behavior in a Peirce-Smith converter has been investigated with a 1/5.7 scale cold model. Dynamic similarity between the model and a commercial converter was attained by setting the modified Froude number in the model experiments in· the range for normal converter operation. It is known that for a given modified Froude number the dimensionless penetration length of gas into the liquid phase increases as the liquid density decreases. Moreover, penetration· length has a large effect on splashing behavior. Therefore, a heavy liquid, a mixture of water and lead concentrate was used as the liquid phase. It was concluded that the amount of splash dramatically decreases with a reduction in the buoyancy energy per, unit liquid mass and an increase in the horizontal distance between the tuyere tip and the edge of the mouth.IntroductionSubmerged gas injection is widely used in practice in ferrous and nonferrous pyrometallurgical operations to achieve large gas-liquid contact areas and good agitation of liquid for rapid chemical reaction. The common application in ·nonferrous industry is the Peirce-Smith converter with multi-tuyere for copper and nickel matte converting. This process has been used for over 100 years because of its effectiveness in mixing of the molten bath, as well as its merits of the engineering simplicity. However, the mechanisms which · determine the blowing performance is poorly understood, and the design and operating conditions of the Peirce-Smith converter varies widely from plant to plant, such as by diameter, length, mouth angle, tuyere position and level of molten matte. Smelters have continuously made an effort to increase converter productivity, implying maximum tuyere blowing rate. Above a certain critical blowing rate, splash of molten matte from the converter mouth becomes unacceptable because of dangerous ejection and accretion buildup around the converter mouth, which results in interference with effective hood sealing. In fact, a 1993 converter survey[!] reported that splash was a major limiting factor for blowing rate and 54% of responding plants from around the world regard it as a limiting condition[2]. In order to increase tuyere blowing rate a study of the effect of various operating conditions on splashing behavior is expected."

Jan 1, 2000

By C. Flores

A novel process using solid metals for the direct reduction of more noble metal ions from solvent extraction organics has been developed. Base metals recovery has been the principal focus of investigations to date but feasibility tests have now also been made on galvanically stripping selected precious metals. In this study gold (III) was loaded from an aqueous HAuCI4 .3H20 solution into a mixed organic 40 vol.% TBP, 10 vol. % D2EHPA in kerosene. The direct precipitation of metallic gold from the loaded organic phase using zinc powder and iron, aluminum and copper slabs at 70 °C was successfully demonstrated. The gold reduction rates were relatively fast even though the conductivity of the organic solutions is very low. The reaction rates were studied as a function of the variables zinc particulate size, oxygen and nitrogen atmosphere, water content in the organic phase, organic ratios and temperature. The gold morphology was usually powdery or dendritic in nature but continuous films were obtained in some instances. Activation energies were calculated and possible reaction mechanisms are discussed. In general, the results obtained were very promising and showed that gold can be successfully cemented from selected organic solvents by galvanic stripping using less noble solid metal reductants.

Jan 1, 1995

By Makoto Ohlsuka

The ternary Ni2MnGa intermetallic compound is an intelligent material which has both a ferromagnetic property and a shape memory effect (SME). The use of the shape memory alloy films for an actuator of micro-machines is very attractive because of its large recovery force. The purpose of the present study is to investigate the effects of fabrication conditions and to clarify the relationships between these properties and fabrication conditions of the Ni-Mn-Ga films. The Ni-Mn-Ga films with a thickness of nearly 5 um were deposited with a radio-frequency magnetron sputtering apparatus using a Ni50Mn25Ga25 or Ni52Mn24Ga24 target. They were heat-treated at various temperatures between 873 and 1273 K for homogenization and ordering and then cooled in a furnace. The composition of the films depended on the sputtering power. The as-deposited films were crystalline and had columnar grains. After the heat treatment the grains widened and the grain boundary became indistinct with the increasing heat treatment temperature. The martensitic transformation temperature of the heat-treated films increased with increasing nickel content. Furthermore the effect of plastic deformation and constraint aging on SME is also investigated. After plastic deformation, the two-way SME was shown through the martensitie transformation and its reversion, The intensity of X-ray diffraction peaks from stress-induced martensitie phase was found. The constraint-aged films also showed the two-way 3ME by thermal cycling.

Jan 1, 2003

By G. J. Abbaschian, A. B. Gokhale, M. M. Kunjapur

"A laboratory scale model furnace was constructed for obtaining radially inward oriented columnar grains in disc shaped castings. The furnace consisted of eleven circular, concentric, equispaced resistance heaters on each half of a split graphite mold. Water or air flowing through a copper pipe along the periphery of the disc constituted the heat sink. After filling the mold, the heaters were turned off consecutively in top and bottom pairs from the rim towards the center, causing the temperature gradients to move inward. Equiaxed structure was obtained at the center by turning off the inner coils together when desired. Sn:15%Pb alloy was used to cast integral blade disc castings using the above technique to obtain dual-property discs with a central equiaxed structure and an outer columnar grain structure projecting inwards from the blades to the rim. A numerical technique was used to predict the temperature profile in the disc during solidification, and good correlation was obtained with the experimentally measured temperature profiles. The corresponding heat transfer coefficient values obtained were h = 544 Wm- 2k-1 (0.013 cal/cm2- ° C-sec) for cooling between metal and chill and h' = 71 Wm- 2k-1 (0.0017 cal/cm2- ° C-sec) for the heat input from the hot mold to the liquid metal. BackgroundHigh temperature alloys used in the current generation of gas turbine engines have evolved through two main stages of development: in 1950's, the increase in the efficiency of gas turbines was paced by improvements in alloy design, which led to the development of Ni and Co-based superalloys (1). By mid-1960's, it was realized that improved alloy chemistry alone was inadequate in meeting the increasingly stringent service requirements. The focus of research then shifted from alloy development to process development, and resulted in the introduction of directional solidification (DS) techniques for the production of turbine blades and vanes (1,2).Under typical operating conditions, the blades and vanes are subjected to aerodynamic loading, while the blades are additionally subjected to high centrifugal loading and vibratory stresses. The primary material requirements for blades may be summarized as follows (1,3):•,High creep resistance•,Good high temperature tensile strength (typically in the range of•,275 to 550 MPa at temperatures in excess of 750°C)•,Resistance to both low cycle and high cycle fatigue (LCF and HCF)•,Resistance to erosion, corrosion, and oxidation•,Resistance to thermal fatigue"

Jan 1, 1986

By M. J. Collins

A hydrometallurgical process has been tested at the Sherritt Research Centre for separation of zinc, lead, copper and precious metal values from the zinc oxide fume leach residue stockpiled at the HBM&S operations in Flin Flon, Manitoba. Zinc is found primarily as zinc femte and sphalerite in the residue, lead as lead sulphate and jarosite, and copper as sulphide and jarositic compounds. Gypsum and siliceous gangue are significant diluents. The separation process includes hot acid, atmospheric and reducing (sulphur dioxide) leaching; zinc, copper and lead flotation; and atmospheric iron removal steps. Zinc is recovered to a high strength zinc sulphate solution and to a zinc sulphide concentrate suitable for feed to a roaster or to a zinc pressure leach plant; lead to a high grade lead sulphate concentrate suitable for feed to a lead smelter, and copper to a high grade copper sulphide concentrate suitable for feed to a copper smelter. Precious metals are divided between the zinc, lead and copper concentrates.

Jan 1, 1993