Search Documents

By Yuanbo Zhang, Zhixiong You, Guanghui Li, Peidan Wen, Tao Jiang

Sn-bearing iron ore containing small amount of Zn, Pb and As is one of the typical complex polymetallic ores in China. This kind of ore is not extensively utilized due to the complicated relationships between iron and other associated nonferrous metal minerals. Excessive contents of these elements would adversely affect the metallurgical operation as well as the quality of steel products. In this study, reduction behavior of Sn was detailedly investigated using H2 or mixed H2/CO as reductant. The results revealed Sn volatilization was improved in the presence of H2 than individual CO/CO2 atmosphere. Simultaneous volatilization of these elements was realized by roasting under weak H2/CO reducing potential, and metallization reduction was advantageous for further Zn volitilization. A metallic pellet (DRI) with Fe metallization greater than 90%, residual Sn, Zn, Pb and As content of 0.054%, 0.012%, 0.0045% and 0.09% was prepared via a simulated reducing gas of coal gasification.

Jan 1, 2015

By Dany Racine, Daniel Marceau, Denis Laroche, Dmitry Lukovnikov

Carbon base materials play a critical role in the performance of Hall-Héroult cell. The determination of their thermo-physical properties is of primary importance for modeling and designing complete cell systems. However, overcoming the associated experimental hurdles is complex and often underestimated. Of them are the Poisson’s ratio measurements and the continuous oxidation/burning of the materials at temperatures above 200°C. The novel procedure developed in this research is based on the Gleeble® 3800 system. Its vacuum chamber allows test with a chosen atmosphere at temperature of more than 1000°C. Young’s modulus, Poisson’s ratio and the coefficient of thermal expansion values can all be adequately measured using a single test. Cylindrical carbon samples (: 50mm, L: 100mm) were tested in the modified system at temperatures ranging from room to 950°C without any trace of oxidation. The resulting values were also in good agreement with literature data for a specific graphite material.

Jan 1, 2015

By Yuanbo Zhang, Yingming Chen, Zijian Su, Bingbing Liu, Jun Chen

Iron, tin-bearing tailings is a kind of hazardous solid waste generated from cassiterite dressing operation. It is difficult to utilize the tailings by present mineral processing methods due to the complex dissemination characteristics. In this study, a process of gas-based magnetizing roasting followed by magnetic separation was studied for separating and recovering iron from the tailings. The effects of roasting and magnetic separation parameters on the recovery of iron were systematically investigated. The optimum parameters were proposed as follows: CO/(CO+CO2) content of 5%, roasting temperature of 850 C, roasting time of 60 min, grinding particle size of 90% less than 45 μm and magnetic field intensity of 800 Gs. Under these conditions, the magnetic concentrate containing 68.5% Fe and 0.06% Sn was achieved, which can be used as high-quality raw materials for direct reduction iron production.

Jan 1, 2016

By J. E. Dutrizac

The mineral forms of silver, lead and cadmium in the zinc concentrates and the various roaster products made by the Kidd Creek Division of Falconbridge Inc. have been elucidated. In the concentrates, all three elements occur mainly in sulphide form, either in solid solution in the principal ore minerals or as discrete mineral grains. During roasting, Ag, Pb and Cd are preferentially concentrated in the hot cyclone and ESP dusts of the roaster train. Silver is converted to <0.5 µm grains of silver metal and to Ag2S04 which dissolves in or impregnates silicates. Lead is converted to Pb-bearing silicates or to PbS04 and PbO which are present either as tiny free grains in ZnO or as an intergrowth with lead silicate. Lead is also a minor constituent of the ferrite phase. Cadmium occurs mostly as cadmium-bearing zno and ZnFe2o4 , but a significant amount also reports as Cd-bearing silicates or zinc sulphate.

Jan 1, 1990

By Hojat Naderi

In this research assisted leaching of chalcopyrite using sodium peroxodisulfate was studied. Electrochemical techniques such as Tafel analysis and electrochemical impedance spectroscopy (EIS) were used to investigate the surface reactions of a chalcopyrite electrode in the presence and absence of Na2S2O8. According to the results, addition of sodium peroxodisulfate increases the current exchange of the corrosion process and prevents the formation of a passive layer on the surface of the electrode. EIS tests show the trans-passive dissolution of the passive layer on the chalcopyrite electrode in presence of Na2S2O8. Equivalent electrochemical circuits were modeled for Na2S2O8-free and -containing solutions and the model parameters were compared to determine the effect of S2O8 2− on chalcopyrite dissolution. Copper dissolution from pure chalcopyrite mineral and chalcopyrite concentrate was carried out using 15 g/L sulfuric acid solution with and without Na2S2O8. Simultaneous presence of 10 g/L ferric ion and 40 g/L peroxodisulfate salt results in about 40 and 18% of Cu extraction from chalcopyrite concentrate and pure chalcopyrite mineral, after 96 h, respectively.

By A. McLean, Y. Uchida, M. Iwase, M. Myochin, K. Wiikimoto

"Phase diagrams of FeO-containing ternary systems could be derived from experimental data for the activities of FeO. The systems investigated are CaO-CaF2-FeO, SrO-SrF2-FeO; BaO-BaF2-FeO, CaO-CaCl2-FeO, SrO-SrC12-FeO, BaO-BaC12-FeO, CaO-A12O3-FeO and BaO-SiO2-FeO.IntroductionThe importance of phase diagram cannot be overemphasized. In a book, ""Alloy Phase Equilibria""[l], the author, Professor A Prince, states, ""A metallurgist has been defined as a person who thinks in terms of phase diagram"". Whether one accepts this statement or not, it is self-evident that an ability to interpret phase equilibria is essential to the professional metallurgists.The physical chemistry studies of iron and steelmaking process often require phase diagrams of FeO-containing slags. Iso-thermal section of the phase· diagrams of such systems can be derived from experimental data for chemical potentials of FeO. Due to the recent developments in the area of solid state electrochemistry, rapid determinations of the FeO activities have become possible. The present paper is aimed at documenting the derivation of the phase diagrams of FeO containing slags.Experimental AspectsAn electrochemical method incorporating stabilized zirconia can be used for the measurements of the activities of FeO in various slags and fluxes[2]. For the details of the experimental technique, reference should be made to reference 2"

Jan 1, 2000

By William Petruk

The concentrator of the Iron Ore Company of Canada consists of spiral circuits, a cone plant and a magnetics plant with regrind. The proportions of liberated and unliberated grains of iron oxides at each point throughout the concentrator were measured by image analysis, and recoveries were calculated for each particle type by the MATBAL materials balancing program. The results show that spirals and cones recover more than 92% of the liberated iron oxide grains in the size range of 848 to 150 um,, but the recovery drops off rapidly for finer grained particles. The tailings from the spirals and cones are reground and low intensity magnetic separators are used to recover liberated magnetite in the -37.5 um size range. The concentrator does not have a unit that efficiently recovers iron oxide grains in the size range of 150 to 37.5 um Consequently about 25% of the iron oxides in the ore are lost to tailings as liberated. grains in the size range of 150 to 37.5 um

Jan 1, 1989

By Lv Guozhi, Niu Liping, Liu Yan, Zhang Zhiqi, He Jicheng, Zhang Ting’an, Dou Zhihe

"CuCr alloy can be extensively used as contact materials in integrated circuit, electrodes, electric contact and high strength conductor. We proposed thermit reduction-electroslag remelting method of preparing the large scale CuCr alloy. But there are pores and oxide inclusions in CuCr alloy prepared by thermit reduction process. This paper studied mainly the effects of ratio of reactant and additive on the inclusion type and their occurrences in CuCr alloy. The slags and CuCr alloy were characterized respectively by XRD and SEM. The results show that when the additive is Na3AlF6, the slag consist of Al2O3 and Cr. When the additive is CaF2, the slag consist of Al2O3, Cr, CaF2 and CaAl4O7. The inclusions in CuCr alloy are mainly Al2O3 and pores which disperse in Cu-rich zone and Cu-Cr phase interface. When 5% CaF2 and 5% KClO3 are added, there are fewer pores and inclusions, and the more better microstructure.1 IntroduceCuCr alloy is the contact terminal material with an eximious properties[1,2], which gradually replaces CuBi alloy becoming the first choice for contact terminal material in the medium and high power vacuum switch after the 1970s. The traditional preparation methods of CuCr alloy mainly contain powder metallurgy, infiltration process and vacuum electric arc melting methods. But the above methods exist some shortcomings, such as poor product quality, high cost of production, processes complex ect[3-9]. CuCr alloy is made by the thermit reduction self-propagating method, which uses CuO, Cr2O3 and Al as raw material to get the high-temperature melt, and then casts to manufacture CuCr alloy ingot, which response equation follows as:"

Jan 1, 2012

By R. G. Reddy

Viscosities of alkaline metal oxide-silicate melts were estimated using our previously developed mathematical model. The structural based model considers depolymerization effects and related breakdown of the silicate network structure, on the addition of metal oxides to the melt. The developed expression: n =4.9x10 9 NO 0 T ½ exp(E/RT) poise was used to calculate the viscosities of various binary silicate systems such as, CaO-SiO,, MgO-SiO, and MnO-SiO,, as a function of temperature and composition. Excellent agreement was obtained between the calculated and experimentally determined viscosities.

Jan 1, 1991

By Li Qian

Mechanisms of bio-dephosphorization from iron ore was investigated in this Paper. The results show that there are two bio-dephosphorization ways from iron ore, the one is that Acidithiobacillus ferrooxidans directly derive phosphorus from the ore, the other is phosphorus is able to be leached acid produced during metabolizing of Acidithiobacillus ferrooxidans, and the latter is more important than the other. Adding suitable pyrite can enhance the bio- dephosphorization process through providing nourishment and producing acid directly due to S 3oxidized or indirectly due to Fe3 as oxidant. The potential varies in the range of 0.434~0.498V and pH is in the range of 2.5 ~ 1.25 during bio-leaching process. It can be founded that, according 2+to the E-pH graph of Fe-H2O system, Fe wouldn?t be oxidized under sterile system in this potential and pH ranges. It can be obviously concluded that the Acidithiobacillus ferrooxidans are 2+able to reduce the potential for the oxidization of Fe and make the oxidization occur in the above pH and potential zone, so the bio-leaching process can proceed. the investigation of E-pH graph of P-H2O system show that H3PO4 can exist steadily.

Jan 1, 2009

By Anja Pfennig, Thomas Böllinghaus, Marcus Wolf

During CCS components are exposed to a corrosive environment and mechanical stress which results in corrosion fatigue and is inevitably followed by the lifetime reduction of these components. The lifetime reduction of the cyclically loaded high alloyed stainless injectionpipe steel AISI 420C (X46Cr13, 1.4034) constantly exposed to highly corrosive CO2- saturated hot thermal water is demonstrated in in-situ-laboratory experiments (T = 60 °C, brine: Stuttgart Aquifer, flow rate: 30 l/h, CO2) in an environment similar to the on-shore CCS-site in the Northern German Bassin. In-situ tension-compression experiments were established simultaneously along with electrochemical measurements using a newly designed corrosion chamber in a resonant testing machine at a frequency as low as 30 – 40 Hz. In addition technical CO2 was introduced into the closed system at a rate close to 9 L/h. S-N plots, micrographic analysis and surface analysis of the fracture surface are demonstrated. X46Cr13 (surface roughness Rz = 4) reached the maximum number of cycles (12.5 x 106) at stress amplitude of 173 MPa producing a low scatter range of 1:3.5. Hydroxide and siderite layers were found on pits and crack surfaces. No typical fatigue limit exists. Pit corrosion prior to crack initiation may be identified as failure cause.

Jan 1, 2016

By Rak-lun Choi

Plasma-induced damage of InGaN/GaN multiple quantum well (MQW) light-emitting diodes (LEDs) has been studied in terms of forward turn-on and reverse breakdown voltages, together with etch rate and surface morphology. The physical degradation of sidewall along with rough surface morphology of n-GaN caused by increased ion scattering induced the deterioration of the forward and reverse voltages. It was found that the turn-on voltage is sensitive to the surface roughness of the etched n-GaN and the breakdown voltage is strongly affected by the sidewall contamination. Annealing under nitrogen after the mesa etching improved the electrical properties of the InGaN/GaN MQW LEDs. Efficient blue light-emitting diodes (LEDs) were fabricated using InGaN/GaN triangular MQWs. The LEDs with triangular QWs showed a lower operation voltage and 2.4 times higher light output power than those with the rectangular MQW LEDs at 20 mA and 20 °C. The intensity of electroluminescence (EL) at 20 mA was almost independent of ambient temperature in the triangular QW LED, but decreased substantially in the rectangular one.

Jan 1, 2003

By Jana Dobrovska

Solidification and cooling of a continuously cast slab and simultaneous heating of a mould is a very complicated problem of transient heat and mass transfer. Nowadays, the solving of such a problem is impossible without numerical models of the temperature field not only of the slab itself, while it is being processed through the whole concasting machine (Caster), but of the mould as well. Two original numerical models have been developed and used in the investigation of a continuously cast steel slab. The first (one of two) 3D model of the temperature field of a concasting is capable of simulating the temperature field of a caster. Experimental research and data acquisition have to be conducted simultaneously with the numerical computation-not only to confront it with the actual numerical model, but also to make it more accurate throughout the process. After computation, it is possible to obtain the temperatures al each node of the network, and at each time of the process. The utilization of the numerical model of solidification and cooling of a concasting plays an indispensable role in practice. The potential change of technology-on the basis of computation-is constantly guided by the effort to optimize, i.e. to maximize the quality of the process. The user can therefore choose any appropriate longitudinal or cross-section of a slab and display or print the temperature field in a 3D or 20 graph whenever necessary. The second numerical model of dendritic segregation of elements assesses critical points of slabs from the viewpoint of their increased susceptibility to crack and fissure. In order to apply this model, it is necessary to analyze the heterogeneity of samples of the constituent elements (Mn, Si and others) and impurities (P, S and others) in characteristic places of the solidifying slab. The numerical model, based on measurement results obtained by an electron micro-probe, generates distribution curves showing the dendritic segregation of the analyzed element, together with the distribution coefficients of the elements between the liquid and solid states. The combination of both models enables the prediction of cracks and fissures in critical points of the continuously cast carbon-steel slab. Both models had been applied in the industrial investigation of a cast low-carbon-steel slab.

Jan 1, 2003

By Jan Dabrovska

Solidification and cooling of a continuously cast slab and simultaneous heating of a mould is a very complicated problem of transient heat and mass transfer. Nowadays, the solving of such a problem is impossible without numerical models of the temperature field not only of the slab itself, while it is being processed through the whole concasting machine (Caster), but of the mould as well. Two original numerical models have been developed and used in the investigation of a continuously cast steel slab. The first (one of two) 3D model of the temperature field of a concasting is capable of simulating the temperature field of a caster. Experimental research and data acquisition have to be conducted simultaneously with the numerical computation-not only to confront it with the actual numerical model, but also to make it more accurate throughout the process. After computation, it is possible to obtain the temperatures at each node of the network, and at each time of the process. The utilization of the numerical model of solidification and cooling of a concasting plays an indispensable role in practice. The potential change of technology-on the basis of computation-is constantly guided by the effort to optimize, i.e. to maximize the quality of the process. The user can therefore choose any appropriate longitudinal or cross-section of a slab and display or print the temperature field in a 3D or 2D graph whenever necessary. The second numerical model of dendritic segregation of elements assesses critical points of slabs from the viewpoint of their increased susceptibility to crack and fissure. In order to apply this model, it is necessary to analyze the heterogeneity of samples of the constituent elements (Mu, Si and others) and impurities (P, S and others) in characteristic places of the solidifying slab. The numerical model, based on measurement results obtained by an electron micro-probe, generates distribution curves showing the dendritic segregation of the analyzed element, together with the distribution coefficients of the elements between the liquid and solid states. The combination of both models enables the prediction of cracks and fissures in critical points of the continuously cast carbon-steel slab. Both models had been applied in the industrial investigation of a cast low-carbon-steel slab.

Jan 1, 2003

By K. Murayama, M. Kawakami, T. Takenaka, S. Yokoyama

"Cokes play an important role of spacer in blast furnace. However, they degenerate during Boudouard reaction. Blast furnace cokes are reacted with pure C02 at I 072 to 1673 K. Reaction rate was obtained by the weight change of spherical specimen. The specimen after reaction was examined by microscopic observation. The reaction rate increased with temperature and was expressed by two Arrhenius type lines. The activation energy was 126 KJ/mol at higher temperature than 13 73 K and 202 KJ/mol at lower temperature range. At the higher temperature range, the reaction proceeded from the surface leaving unreacted core, whereas homogeneously whole inside at lower temperature. The porosity increased from the center to surface at higher temperature, whereas it was almost constant at lower temperature.IntroductionThe cokes have the function of fuel, reductant and spacer to keep gas and liquid flow in the blast furnace. Thus, the reaction mechanism of coke with several gas and the strength after the reaction should be important factor to control the blast furnace operation. The reaction mechanism of coke with C02 has been studied extensively. The rate equations were derived by Gadsby[ I], Ergun[2] and Turkdogan and Vinters[3]. They were compared and discussed by Kobayashi and Omori [ 4]. Effect of crystallization degree on the reaction rate was examined by Kashiwaya and Ishii[5]. Catalytic enhancement effect of ash componets have been clarified by Kashiwaya et. al. [6]. Although degradation of coke in blast furnace has been examined recently[7], however, the degradation of coke after the reaction with C02 has not been well clarified yet. In the present work, the metallurgical coke specimen was heated in N2 and C02 and the reaction mechanism and degradation behavior after the reaction was investigated."

Jan 1, 2000

By M. Y. Mohassab-Ahmed

In an effort to develop a novel flash ironmaking process, the chemistry of selected slags was investigated. In different ironmaking processes, the molten bath (iron-slag bath) is expected to be in contact with gas atmospheres of H2/H2O, CO/CO2/H2/H2O, and CO/CO2. The latter was investigated to allow comparison with the blast-furnace conditions. The slag composition was selected to resemble that of the blast furnace with CaO/SiO2 in the range 0.8 to 1.4. The temperature range was 1550 to 1650°C. The oxygen partial pressure was maintained in the range 10-10 to10-9 atm. The effect of water vapor on the chemistry of the slag as well as the equilibrium reactions involving the slag has been studied for the first time. H2O dramatically affects the chemistry of the slag and strongly affect the phase equilibria in the slag as well as the equilibrium distribution of elements between slag and molten metal.

Jan 1, 2014

By José D. T. Capocchi

Viscosity of liquid lead, tin, and Pb-Sn alloys has been measured by the rotational viscometer method in the temperature range from 50 K above their respective liquidus temperature to 823 K. The results are accurate to within ±1.0 %. The variation of viscosity with temperature followed the Arrhenius-type equation µ = µo.exp(Q/RT). The composition dependence of the isothermal viscosity and the activation energy for viscous flow have not shown anomalous changes at the eutectic composition of the Pb-Sn system.

Jan 1, 2000

By G. Diáz

A basic technology coping with a wide range of secondary zinc sources has been developed. The process combines an electrowinning stage, a solvent-extraction unit and a leaching procedure. The acidity generated in zinc electrowinning, transferred by the organic solvent to the aqueous raffinate, is reused to leach the zinc secondary materials. The basic process recovering zinc is described in detail. The route recovering other valuable metals such as copper, cadmium and lead associated with zinc is also described. This non-ferrous metals recovery route is advisable for either ecological and/or economical reasons. Main results of an experimental program aiming at the demonstration of the suitability of the process for several feed materials are summarized. Waelz oxides, galvanizing ashes and EAFD coming from different sources were tested in laboratory and continuous pilot plant campaigns. High zinc recovery, low reagents and utilities consumption, and effluents meeting environmental regulation were confirmed. The paper also includes the main results of a feasibility study of an industrial "base case". A mixed raw material and Spanish EAFD and 20,000 ta of zinc ingots production were chosen. The SGH zinc recovery from secondary raw material by means of the clean, safe and profitable Modified Zincex Process has been demonstrated. This reliable technology is ready for industrial application.

Jan 1, 1995

By Cong Wang, Siyang Long, Pengcheng Zhang, Haibin Zuo

This paper introduced the research progress of microwave treatment on coal. The mechanics of microwave treatment mainly include thermal effects and non-thermal effects. Thermal effects, which lead to cracks and changes of pore structure, attribute to the selective heating of microwave. Non-thermal effects involve the removal of oxygen functional groups, improvement of coal rank and decomposition of minerals. Therefore, microwave treatment of coal has a lot of potential applications, mainly including drying, desulfurization, improvement of grindability, enhancement of coal-water slurry property and change the combustion and gasification properties.

Jan 1, 2016

By Jonkion M. Font, Ramana G. Reddy

A thermodynamic model for a priori predictions of arsenic and antimony impurity capacity in Ni-Cu mattes and slags was developed based on the Reddy-Blander (RB) capacity model. The As and Sb capacities were calculated a-priori considering the RB capacity model in Ni-Cu mattes and FeO-FeO1.5-MgO-CuO0.5-NiO-SiO2 slag at 1573 K and 0.1 to 1 atm partial pressure of SO2. The results showed an excellent agreement between the model calculated and experimental data of arsenic and antimony capacities between the mattes and slag. The impurity capacity model developed here, can be extended for prediction of impurity capacities in multi-component base metal slags and base metal mattes. Such a priori predictions of impurity capacities can lead to develop or improve the efficiency of impurity removal from the base metal smelting, converting and refining processes.

Jan 1, 2014