Search Documents

By Anthony (Sam) J. S. Spearing

Backfilling using coal waste is not a novel means for waste disposal throughout the world; yet, backfilling using a high density (paste) backfill is relatively new, except in Germany and Poland. One of the main benefits of a high density backfill, as opposed to a low density (slurry) backfill, is that, if placed at a low permeability and low moisture content, the risk of water table contamination can be relatively low. In addition, if paste backfill can be placed cost effectively, environmental benefits are huge because the surface impoundment footprint can be greatly reduced or even eliminated. This is especially true in room-and-pillar applications. In its current state, backfilling is considerably more costly than surface disposal. This is mainly because paste, as opposed to slurry, significantly increases backfill placement costs; however, this could be offset by increasing the achievable extraction rate. Overall, such a system could potentially improve the public?s image of coal mining in the US for a myriad of reasons. This paper discusses a proposed backfill system for a typical room-and-pillar coal mine in the Illinois Basin of the US and clearly shows the technical advantages, although costs are still higher with fill. The cost differential will likely reduce over time, in favor of the backfill option, as costs of traditional surface disposal increase, due mainly to ever-restrictive disposal regulations.

Jan 1, 2013

By Andrew Lewis, Amarit Nitaramorn, Alexander Garcia, Peter Altounyan

"Indonesia is a major coal producer, the vast majority being sourced from opencast operations. Underground production to date has been constrained by unfavorable ground conditions and limited local experience. However, an underground trial in East Kalimantan has now shown that it is possible to successfully extract coal and mine safely, despite the technical challenges.A trial drift mine has been worked to a current maximum depth of 160 m (525 ft) in a dipping coal seam. The 3 m (10 ft) thick coal seam is overlain by very weak mudstone and sandstones. The mudstone forming the immediate seam roof strata proved a particular challenge given its adverse reaction to water and overall friability.Rock bolts were used as roadway support, the system being carefully selected to optimize effectiveness. An innovative method of partial extraction was trialed, which demonstrated the potential for productive mining despite the ground conditions. Roof falls have occurred within the working area, and roadways demonstrate reasonable stability over time.Throughout the course of the trial, strata behavior monitoring has been an important aspect, and a comprehensive ground control monitoring system is in place. This has enhanced the ability to increase the level of support where required and to react to deteriorating conditions. In addition, monitoring information has allowed a quantitative assessment to be made of the technical feasibility of future full-scale mining.INTRODUCTIONWith current production at over 200 million tons, much of this destined for overseas markets, Indonesia is the second largest exporter of coal (Ritschel and Schiffer, 2007). The majority of the coal is sourced from the Kalimantan coalfields. Mining is predominately opencast, yet in recent years there have been attempts made to introduce underground operations. This move would permit continued access to good quality seams that are beyond the reach of viable opencast mining."

Jan 1, 2010

By Monte R. Hieb

Study of moisture-induced swelling strain in Pennsylvanian Period rocks of the Appalachian Plateau in West Virginia shows a 2:1 biaxial horizontal anisotropy which trends NW-SE. Oriented in-situ slabs of coal mine roof rock were collected across West Virginia, dry-sawed to size, air-dried to stability, and then monitored for moisture changes and deformations in the horizontal plane through one wetting cycle and drying cycle. Biaxial swelling strains were exhibited in nearly all rocks tested, with maximum horizontal deformations occurring normally-incident to the strike of regional geologic fold structures. This relationship persists as fold strike varies across the study area. A connection with Alleghanian fold development and/or post-Alleghanian fold relaxation is suggested. Deformations were largest in shales, but occurred in sandstones and siltstones as well. During testing, moisture-induced fractures (MIF) developed parallel to the regional fold structure and ranged in size from hairline cracks to sample-destroying cracks that were orthogonal to the observed biaxial swelling strain direction. Preferential wetting and swelling of clay minerals along NE-trending fractures, related to a fold-parallel fracture fabric of regional extent across West Virginia, is the most likely reason for the observed systematic NW-oriented biaxial swelling strains. The testing methods used in this study are simple and inexpensive and produce robust results that offer insight into a regional, anisotropic mechanical weakness that imparts a dynamic, asymmetrical horizontal stress to moisture-sensitive coal mine roof rocks over time. Because a similar mechanical fabric has been reported in Devonian-age shales, these findings may have implications for shale gas developers in the Appalachian Basin challenged by rapid aperture closure rates along horizontallydrilled induced fracture networks in Devonian rocks like the Marcellus Shale. The paper concludes with an example of how the concept of a preferred swelling strain direction might be applied to improve the effectiveness of roof trusses.

Jan 1, 2013

By Michael Gauna, Christopher Mark

"Underground coal mining in the U.S. is conducted in numerous regions where previous workings exist above and/or below an actively mined seam. Miners know that overlying or underlying fully extracted coal areas, also known as gob regions, can result in abutment stresses that affect the active mining. If there was no full extraction, and the past mining consists entirely of intact pillars, the stresses on the active seam are usually minimal. However, experience has shown that in some situations there has been sufficient yielding in overlying or underlying pillar systems to cause stress transfer to the adjoining larger pillars or barriers, which in turn, transfer significant stresses onto the workings of the active seam. In other words, the overlying or underlying pillar system behaves as a ""pseudo gob."" The presence of a pseudo gob is often unexpected, and the consequences can be severe. This paper presents several case histories, summarized briefly below, that illustrate pseudo gob phenomenon:• Pillar rib degradation at a West Virginia mine at 1100-foot (335 m) depth that contributed to a rib roll fatality.• Pillar rib deterioration at a Western Kentucky mine at 570-foot (175 m) depth that required pillar size adjustment and installation of supplemental bolting.• Roof deterioration at an eastern Kentucky mine at 1300- foot ( 400 m) depth that stopped mine advance and required redirecting the section development.• Coal burst on development at an eastern Kentucky mine at 1700-foot (520 m) depth that had no nearby pillar recovery.• Coal burst on development at a West Virginia mine at the relatively shallow depth of 1100 feet (335 m) that also had no nearby pillar recovery.The paper provides guidance so that when an operation encounters a potential pseudo gob stress interaction the hazard can be mitigated based on an understanding of the mechanism encountered.INTRODUCTIONThe U.S. underground coal mining industry has conducted mining in multiple seam environments, where the active mining has underlying or overlying old workings at varying interburden distances, throughout its history. Often no serious consequences arise from the multiple seam mining. However, sometime mines have been confronted with hazards from underlying or overlying workings that include localized roof and rib failure, pillar system failures through propagating roof falls and floor heave, and also pillar bursts."

Jan 1, 2016

By David R. Burkhard

"Comparative roof beam performance, as measured by delamination within the bolted horizon, was used to evaluate two types of roof bolt drill hole geometries in a development setting. Short encapsulation pull tests had demonstrated a higher grip factor in drill holes featuring helical grooves in the side walls in comparison to drill holes featuring continuous smooth to slightly rough walls. The study incorporated the two geometries during development mining in which fully grouted mechanically anchored bolts were installed as primary roof support.bolts were installed as primary roof support.The study site, in an entry adjacent to a longwall panel, was instrumented with extensometers and data collected during longwall retreat. Statistical analysis was conducted to validate null and alternative hypotheses used to compare drill hole geometries. Analysis yielded no statistically significant difference between drill hole geometries. Inspection of the data does reveal less delamination within the smooth walled site in comparison to the site containing grooved hole geometry.INTRODUCTIONFrom their introduction as a means of ground control over sixty years ago, roof bolts today are the primary mechanism of roof support utilized throughout mining. Whether through suspension, keying, or beam building, roof bolts are employed to reinforce the inherent strength of the strata comprising the immediate roof with the goal of creating a competent bolted horizon of sufficient load bearing capacity to be self-supporting for a given mine's design life, stress regime, and geomechanical properties.For grouted bolts in sedimentary strata, axial loading due to vertical rock movement and bending due to horizontal rock movement are the principal means of loading (Signer, 2000). Regardless of the type of bolt and extent of grouting employed, the success of any roof bolting design is determined, to a large extent, by the effectiveness of load transfer between the rock, grout, and bolt.At San Juan Mine, an underground longwall mine located in the northwestern corner of New Mexico, a number of different roof bolt types, grades, and lengths have been used over the years in an effort to optimize primary roof support. One common denominator shared throughout has been the use of full length grout. Load transfer for full length grout is achieved primarily through mechanical bonding between the grout and rock. It is this interaction that is the focus of the study described in this paper. The study assessed and compared two types of bolt hole geometries employed during gate road development at San Juan. Underground instrumentation and evaluation of the bolted roof provided the means of assessment and comparison."

Jan 1, 2016

By Ted Klemetti, Gabriel Esterhuizen, John L. Ellenberger

"Advanced numerical models can be used to evaluate entry support systems in coal mines. However, these methods require specialized software and specialized skills to create the models and evaluate the results. Practicing support design engineers require a method to rapidly assess a proposed support system for a given geotechnical scenario. A prediction equation that can be used to assess roof support systems has been developed from the results of hundreds of FLAC3D analyses that were conducted during recent research. These models were validated against field cases and empirical design approaches and were found to adequately predict entry stability in coal mines. The understanding developed from the model outcomes was used to develop an equation to predict entry roof stability against large roof falls. Least-squares error analysis was conducted to find appropriate parameters for the nonlinear equation. The developed equation can be solved using spreadsheet software, allowing for rapid assessment of alternative support system performance in variable geological conditions. The performance of the prediction equation is evaluated against empirical design methods and against selected case histories of support practices at currently operating mines. Examples are presented that demonstrate the performance of the equation in variable geological settings. The stability factor (SF) prediction equation can be used as an assessment tool to assist in the design of coal mine roof support systems.IntroductionGround falls represent a significant proportion of injuries and fatalities in underground coal mines in the US. During 2013, ground falls were responsible for 4 of the 14 fatalities and 16.6 % of the 1,577 reportable lost-time injuries (MSHA, 2015). In addition, each year about 400 to 500 large roof falls are reported that can extend up to or above the bolted horizon. Large roof falls and associated ground fall hazards can be mitigated through improved support design.The research presented here particularly addresses the problem of large roof falls that extend more than 90 cm (3 ft) above the roof line of an entry and may extend above the bolted horizon. Smaller roof falls that fall out between supports or extend less than 90 cm (3 ft) above the roof line are excluded. These smaller roof falls can be controlled by appropriate surface support such as roof screen or other skin control methods. Also excluded are roof falls that are associated with an individual geological structure such as a slip of fault. Structure-related instabilities can be controlled by strategically locating individual roof bolts or other supports appropriate for the local situation."

Jan 1, 2015

By Long Fan, Shimin Liu, Guijie Sang

"Weak shale roof falls have long been the main cause for fatalities in underground coal mines. Moisture-induced swelling is one of the root causes for the degradation of roof shales. In this study, slake durability tests are conducted on shale samples collected from Illinois basin coal mines, and different levels of durability are analyzed according to Gamble slake durability classification. There are two main mechanisms influencing the shape of retained fragments after two cycles of wetting and drying: mechanical abrasion and swelling pressure. A prototype optically based shale swelling apparatus is designed and manufactured for the shale free-swelling measurement. The experimental results suggest that swelling pressure tends to deteriorate shale laminations. Moisture-induced swelling of the No. 6 roof shale from Bear Run Mine was measured under 100% relative humidity condition. The measured swelling strain normal to beddings is ~5 to 7 times greater than the swelling strain parallel to beddings. This suggests that interlayer expansion plays a key role in moisture-induced swelling. Cracks induced by swelling pressure tend to occur along the bedding plane and lead to shale deterioration. INTRODUCTION Background Ground falls have long been the cause for nearly 50% of all fatalities in underground coal mines and continue to be one of the greatest safety hazards in underground spaces. Among the various ground fall hazards, roof failure takes up 23% of total fatalities in underground coal mines, of which 13% are due to skin failure and 10% are due to massive roof falls (Mark, Pappas, and Barczak, 2011). Roof failures associated with weak shales are summarized in previous studies (Molinda and Mark, 2010; Aughenbaugh and Bruzewski, 1973; Bajpayee, Pappas, and Ellenberger, 2014; Murphy, 2016). For mine roof instability and failure, two aspects can explain the failure mechanism of weak roofs. One is the elevated stress concentration in lateral direction due to the mining-induced excavation and its stress redistribution around the mine opening (Song and Stankus, 1997; Fan and Liu, 2017; Hill, 1986). The other mechanism is the passive stress-relief due to the strength weakening induced by the ambient moisture and temperature fluctuations during a period of time. Shale is moisture sensitive and presents a lower durability if it is exposed to a highly humid environment for a long time, thus leading to roof deterioration and instability in underground coal mines (Aughenbaugh and Bruzewski, 1976; Stateham and Radcliffe, 1978; Chugh and Missavage, 1981; Klemetti, Oyler, and Molinda, 2009). It is well known that shale is a clay-bearing sedimentary rock and that clay minerals are water sensitive. The moisture uptake for shale will induce the micro-deformation of a shale matrix, thus the structure and strength of shale is a function of time and intensity of moisture exposure. All mine engineers notice moisture-induced shale deterioration; however, the underlying mechanism(s) are still not fully understood due to the complexity of geophysical-chemical water-shale interactions (Huang, Aughenbaugh, and Rockaway, 1986; Hensen and Smit, 2002; Diaz-Perez, Cortés-Monroy, and Roegiers, 2007). The coal mining industry is still in the process of finding a technically sound, cost-effective technology to prevent this unexpected and unpredictable shale roof failure. Therefore, understanding how the moisture-sensitive shale responses to various ambient moisture and what role exposure duration plays in shale roof failure is key to prevent unexpected roof incidents, which will lay the foundation for the long-term roof support design and ground control management."

Jan 1, 2017

By Jimenez Leon, Christopher Newman, Boede Gabriel, Zacharias Agioutantis

"Ground movements due to longwall mining operations have the potential to damage the hydrological balance within as well as outside the mine permit area in the form of increased surface ponding and changes to hydrogeological properties. Recently, the Office of Surface Mining, Reclamation and Enforcement has completed a public comment period on a newly proposed rule for the protection of streams and groundwater from adverse impacts of surface and underground mining operations (80 FR 44435). With increased community and regulatory focus on mining operations and their potential to adversely affect streams and groundwater, there is now a greater need for better prediction of the possible effects mining has on both surface and sub surface bodies of water.As mining induced stress and strain within the overburden is correlated to changes in the hydrogeological properties of rock and soil, this paper investigates the evaluation of the hydrogeological system within the vicinity of an underground mining operation based on strain VALUES (calculated through a surface deformation prediction model. Through accurate modeling of the pre- and post-mining hydrogeological system, industry personnel can better depict mining induced effects on ground water flows through the overburden material aiding in the optimization underground extraction sequences while maintaining the integrity of surface and subsurface bodies of water.INTRODUCTIONThe utilization of high-recovery underground mining methods, such as longwall or high-extraction room-and-pillar operations, have the potential to cause adverse impacts to both surface and subsurface bodies of water as strata movement and deformations propagate from the mined seam through the overburden to the surface (Peng, 2008).Previous research has indicated that mining induced strains are the most damaging to surface streams (Singh, 1992) as well as greatly affecting the integrity of subsurface bodies of water and groundwater flow conditions (Booth, 1986). On the surface, adverse effects to the stream can occur due to the development of either tensile or compressive strain in the stream bed. The development of tensile cracks along the bedrock allows for a potential loss of stream flow through developed fissures. In fact, water flow in the Cataract River of Australia ceased in 1994 as a result of mining-induced strains from longwall operations in the Bulli seam 430 meters (1320 feet) below the river gorge (McNally and Evans, 2007). On the other hand, the development of compressive strains within the rock layers can cause rupturing or buckling of the stream bed, blocking stream flow and/or diverting flow into the fractures at the base (Iannacchione et al, 2010). While these localized fractures can contribute to the loss of stream flows, given time, damaged streams have the ability to self-heal through the regeneration of near-surface aquifers as well as the sealing of mining-induced fractures with rock debris, gravel, sand, clay or other soil particles carried from upstream sources and deposited in the river bed (Waddington and Kay, 2002)."

Jan 1, 2016

By Ashok Kumar, Rajendra Singh, Arun Kr. Singh

"A simple analysis of site conditions and capability of the mechanised depillaring (MD) operation found that this approach is suitable to address the strata control issues in coal pillar extraction under the weak and laminated roof strata of Pinoura mine. A continuous miner (CM) with a ram car and quad-bolter are used for single pass pillar extraction (first time in the country) to achieve a relatively faster rate of depillaring. A total of eleven panels are depillared under weak and laminated roof strata with a fair-rated rock mass rating (CMRI-RMR). It is observed that there is less influence of roof caving over the surrounding mining structures, especially those located out-bye the side of the extraction line. An attempt is made to quantify the goaf influence by field studies, which show that the maximum value of mining-induced vertical stress is 2.83 MPa, and the range of influence remains limited to around 15 m from the line of extraction. However, the problem of roof instability under the influenced zone was experienced due to the inherent nature of the weak roof strata. The chances of trapping of CM under weak and laminated roof strata of the panels is reduced by deriving a threshold value of the roof dilation, on the basis of a simple statistical analysis of the obtained field results. However, few incidences of roof collapses are observed over the CM due to the unpredictable behaviour of the geological structures below the freshly exposed strata, which also caused an obstruction in the speed of the extraction. This paper presents results of the field and laboratory studies, conducted for a successful application of the single-pass pillar extraction method, along with details of some CM trapping cases below the weak and laminated roof strata.INTRODUCTIONCoal is the major natural resource to meet the growing energy demand of India and this trend is likely to continue for the next 20 years in the country. A major part of the Indian coal belongs to Gondwana period, and only a small part belongs to Tertiary period. The estimated coal reserve in India per the exploration work done up to a maximum depth of 1200 m is 315.149 billion tonnes, including the proven coal reserve of 143.058 billion tonnes (CMPDIL, 2017). Even in presence of these huge resources of coal in India, there is a considerable gap between production and the users’ demand of coal. Most of the mines are operated by conventional semi-mechanised Bord and Pillar (B&P) methods; thus, the mining industry has gained a considerable amount of operational experience (Singh, Singh, and Dhar, 1996) and knowledge about strata behaviour (Singh and Singh, 1999; Singh et al., 2008) using this method. However, recently, the Indian coal mining industry has introduced some mechanised depillaring (MD) operations, where the level of production is relatively high. This approach of depillaring improves safety along with the production and productivity of a depillaring operation (Ram et al., 2017). The nature of the overlying strata of these depillaring operations vary greatly: from highly laminated, weak, and easily caveable to massive, strong, and difficult to cave."

Jan 1, 2018

By Guy Reed, Russell Frith

"The method of determining coal pillar strength equations from databases of stable and failed case histories is more than 50 years old and has been applied in different countries by different researchers in a range of mining situations. While common wisdom sensibly limits the use of the resultant pillar strength equations and methods to design scenarios that are consistent with the founding database, there are a number of examples where failures have occurred as a direct result of applying empirical design methods to coal pillar design problems that are inconsistent with the founding database.This paper explores the reasons why empirically derived coal pillar strength equations tend to be problem-specific and should be considered as providing no more than a pillar strength “index.” These include the non-consideration of overburden horizontal stress within the mine stability problem, an inadequate definition of super-critical overburden behaviour as it applies to standing coal pillars, and the non-consideration of overburden displacement and coal pillar strain limits. All of which combine to potentially complicate and confuse the back-analysis of coal pillar strength from failed cases.A modified coal pillar design representation and model are presented based on coal pillars acting to reinforce a horizontally stressed overburden, rather than suspend an otherwise unstable self-loaded overburden or section, the latter having been at the core of historical empirical studies into coal pillar strength and stability.INTRODUCTIONThe inspiration for this paper is founded in three statements from two eminent persons in the field of coal pillar strength research, Jim Galvin and Essie Esterhuizen, as follows:Both Salamon and Munro and [the University of New South Wales] based the derivation of their pillar strength formulae on a criteria that the diameter of a panel of pillars, W, had to at least equal the depth of mining, H. This was thought to result in full tributary loading. It is now known that there are some mining environments included in both the South African and Australian databases in which mining span must exceed depth by a considerable margin in order to achieve full deadweight loading. Hence, it is logical to conclude that these data points may have contributed to pillar strength being overestimated by Salamon and Munro and UNSW (underline added by authors). Normally, this should be of no consequence because it is reflected in the probability of design success associated with any given safety factor (Galvin, 2006)."

Jan 1, 2018

By Michael J. Castner

"INTRODUCTIONMultiple-seam mining is an ever growing concern for engineers and mine management in every portion of the mining industry and is especially true for coal mining operations. The goal of this report is to identify the location and severity of multiple-seam interactions, provide AMSS calculations performed on the worst of these locations, and follow up with a visual examination of the underground physical effects on the roof and ribs in the locations identified for analysis. Multiple-seam mining is increasingly being studied because:1. Multiple-seam mining can create a multitude of problems such as roof falls, pillar crushing, pillar failing, rib spalling, floor heave, and inundation of water, gas, or oxygen-deficient air that can disrupt mining operations and threaten the safety of the miners.2. Multiple-seam mining is becoming more prevalent due to the depletion of virgin coal reserves.Currently, coal mining in the United States has progressed to the point that a growing number of mining companies are operating in coal seams located above, below, and/or adjacent to previously mined out coal seams. As a result, the state and federal governments are enacting higher safety standards on mining operations. For example, in years past, pillars may have been properly designed to handle single seam interactions for a particular mine or mines; however, today, where mining is now being considered above or below a previously mined area, these loading conditions may not be adequate to handle the removal of additional seams above or below the previously mined reserve. Studies from 1981 estimated that two-thirds of the mineable coal reserves in the United States would be impacted by multiple-seam implications. Today, over three decades later, it is obvious that most of the remaining mineable coal reserve will be influenced by previously extracted seams. Thus, thefocus on multiple-seam mining interactions on current and future mining operations. In 2012, underground mining in the United States produced 342,287 thousand short tons of coal. Northern Appalachia accounted for over 30% (103,301 thousand short tons) of this total (U.S. Energy Information Administration, 2013). Rosebud Mining Company and Western Allegheny Energy (RMC and WAE) have a combined total of 23 actively producing underground mining operations and at least four new mines under or ready for development. All of these mines are located in coal seams (Upper and Lower Freeport; Upper, Middle, and Lower Kittanning) of northern Appalachia (Pennsylvania and Ohio). Currently, more than half of the RMC and WAE mines are dealing with multiple-seam interactions. Seven mines are undermining previously mined out coal seams, and five mines are overmining previously mined out coal seams. Also, between these companies, five mines have inner-seam sloping possibilities (2 completed, 3 planned), most of which will result in mining over or under previously mined areas."

Jan 1, 2015

By Dion Pastars

Kestrel Coal has undertaken a surface-to-seam consolidation program of faulted ground prior to longwall retreat in the 304 panel. Micro fine cement is used to improve the rock mass quality and therefore reduce the risk to personnel and equipment whilst increasing previously assumed sterilised reserves. The program is based on information attained from previously successful grouting campaigns in the Queensland coal area and follows the decision making process to ensure there is sufficient spatial permeation of cement across the faulted area. This data is used to assess the residual risk to the business in terms of health, safety and production

Jan 1, 2007

By Eric Westman

Ground control problems caused by multiple-seam interaction frequently sterilize coal reserves. Interaction mechanisms differ for overmining and undermining and are controlled by mining, spatial. and geologic conditions at each site. A multiple-seam interaction analysis software program, UGLY (Uppersearn Gateroad Longwall Stability), has been used to evaluate sterilization of coal reserves due to overmining at three locations. Four case histories were reviewed to determine the effectiveness of improved ground control in mitigating interaction effects.

Jan 1, 1997

By Brian E. Travis

Recent Developments in the utilization of polymer grid structures for Longwall Shield Recovery operations are discussed. Specifically: various Longwall screen designs and the numerous methods employed during installation. Also discussed is the role of polymer grid structures in head and tailgate mf and rib control and their role in controlling soft bottom often associated in shield recovery operations.

Jan 1, 1993

By R. D. Lama

The concept of rigid or yielding bolts is discussed based upon support requirements for excavations of equivalent geomechanical behaviour. The concept of equivalent geomechanical behaviour is introduced for comparison purpose where the rock mass properties are varied for a given depth (stress) so that the deformation of the roof without any support remains constant = 300mm. A simple experimental theoretical analysis for a uniform stress field acting on an axi-symmetric excavation is conducted to establish roof bolt requirements under different conditions such as width of a given excavation, time of setting of support etc. Results are presented in graphical forms.

Jan 1, 1992

By John Stankus

Seam interaction in multiple seam mining has significant effect on entry stability. The remaining pillar in an old working usually creates a high stress concentration zone while the gob creates a stress release zone. A good panel layout should take advantage of the stress release effect created by old workings. This paper presents two case studies of multiple seam mining. The Jennmar Finite Element Analysis System (JFEA) is utilized to analyze the seam interaction effect and identify the mess concentration and relief zones Panel layouts are designed bad on the results of the finite element analysis Appropriate roof support system are also designed for different seam interaction areas.

Jan 1, 1999

By André Vervoort

In coal room and pillar, and pillar extraction panels, the sidewall conditions were investigated based on underground measurements and numerical simulations. Three-dimensional linear elastic models provided a useful and quick prediction of the amount of sidewall spalling. However, more complex constitutive models were required to simulate more accurately the extent of fracturing and its effect on the stress re-distribution. The input parameters of a Mohr-Coulomb model were determined by back-analysis of underground measurements, and the effect of the depth of the workings and the time dependent occcurrence of coal pillar fracturing were analyzed.

Jan 1, 1992

By Jialin Xu

Bed separations position, size, development characteristics and their influence factors have been analyzed in-depth by experimental and theoretical methods. The results show that the key strata determine the creation, development and space-time distribution of the overburden bed separations and fractures. Based on the dynamic growth principle during the two-stage development of bed separations, the theory of section-grouting for the overburden bed separation space and the O-ring theory for the pressure-relieved methane drainage are proposed. The technique has been applied in some coal mines in China to reduce surface subsidence and for methane drainage. Keywords: rock strata movements; key stratum; bed separation; bed separation grouting; pressure-relieved methane drainage

Jan 1, 2003

By R. W. Hill

Multiseam mining has been carried out at many collieries in South Africa. It the seams are In close proximity difficult and dangerous mining conditions may arise. In the Witbank area multiseam bord and pillar mining has been carried out, while in Natal where the seams are thinner and of a higher quality, total extraction methods are common. Several combinations of multiseam mining have been carried out. The paper highlights a number of case studies and the strata control problems that can arise.

Jan 1, 1995

By Ed D. Doney

Based on the subsidence data collected through a comprehensive subsidence monitoring program con: ducted over two longwall panels in an Illinois coal mine, mathematical models have been proposed for predicting final and dynamic subsidence in the Illinois coal basin.

Jan 1, 1990