Search Documents

By Peter Zhang

The immediate roof at the test site consisted of laminated clay shale that is likely to be susceptible to weathering. With seasonal dry-wet cycles in the mine ventilation air, the roof in the intake air would deteriorate and lose integrity over time. In many instances, the weathering-prone roof would gradually scale off piece by piece between bolts and over the entry corners. In some long-term entries, roof weathering could develop up to 2-3 ft deep with columns of bolted roof hanging under the upper intact roof. If wire mesh is used, the roof bags down and reduces the entry height, and the weight of the bagged roof tends to pull the bolts out and poses a safety hazard. An effective measure is always sought to support this type of weak roof that is sensitive to moisture degradation. One solution is to seal the roof shortly after entry development to prevent moisture penetration so that roof integrity can be maintained for the long term. In this application, a polymer-based sealing material was tested in the Rockspring mine for weathering protection and reinforcement. The material is a one-component polymer powder for spray application onto the roof and rib. The sealant material is mixed with water in the spraying nozzle to apply to the roof and rib as a paste. The product sets within 5-10 minutes and forms a membrane as thin as about 1/8-in. The membrane will quickly develop tensile and bonding strength within minutes and completely cure within a few days. Through sealing, bonding and lateral reinforcement, the integrity of the weak roof can be maintained. The material has been tried in a long-term evaluation over several months in a set of main entries in the Rockspring mine owned and operated by Rockspring Development, Inc., affiliate of Foundation Coal. Preliminary evaluation has shown that the material is an effective and economical solution to ensuring the long-term stability of weathering-prone roof.

Jan 1, 2009

By Ihsan Berk Tulu

In the Analysis of Retreat Mining Pillar Stability (ARMPS) program, the magnitude of the abutment loading adjacent to a gob area is calculated using an ?abutment angle? concept. The extent of the abutment loading is determined solely as a function of depth from an empirically derived equation. In the recommended calibration method for LaModel, it was believed that the empirical equations for calculating the magnitude and extent of the abutment load, as used in ARMPS, were the best available methods for determining these critical overburden loading values. Therefore, similar calculations were implemented in the LaModel calibration method. However, the latest in situ stress measurements of abutment loading performed in the United States and Australia have shown that there can be significant deviations in the measured abutment magnitude and extent as compared to the predicted values from the empirical formulas used in ARMPS and LaModel. It seems reasonable that the overburden geology, depth, extraction panel width, and mining height should have a significant effect on the extent and magnitude of the abutment load. However, the current empirical formulas do not incorporate many of these significant parameters into determining the abutment load on the pillars. In this paper, stress measurements from US and Australian mines were back-analyzed by using analytical and numerical methods to investigate the measured abutment extent and loading. Ultimately, it was determined that the original empirical abutment extent formula in conjunction with the original ALPS square-decay stress distribution function was supported by the case histories in this paper. Also, for depths less than 900 ft, the average 21° abutment angle was supported by the case histories; however, at depths greater than 900 ft, the abutment angle was found to be significantly less than 21° and should be calculated with a new proposed equation.

Jan 1, 2012

By John C. Stankus

To improve mine roof bolt performance, Jennmar Corporation commenced the design and development of a new roof control sys- tem. This new system designated "Insta'l Compression", not only improves safety, but is more cost efficient due to reduced amounts of resin needed per bolt installation. In this paper the research and development of this new system will be outlined. Much of the information presented will be actual test data from various underground operations in Alabama, Kentucky, and Pennsylvania. The development of this system will also cover the design of a new expansion shell, resin compression ring, anti- friction washer, and upgrading of material specifications.

Jan 1, 1990

By S. Yamashita

Recently in Japan, unexpected degradation (surface subsidence) at old underground quarry sites, such as 'Ohya-Ishi' (pumice tuff) pit field has often been occurred. At these quarry sites, the excavation was started 20 or 30 years ago with mechanical chain cutter and the Room and Pillar method, and stopped 7 or more years ago. Therefore, a reliable method has been required for an estimation of long term mechanical properties of the rock and for an observation of a stability of rock-pillars or structures. In this study, creep tests under uniaxial compressive load were carried out on the 'Ohya-Ishi', with the aim of estimating the long term stability of the rock. From these results, a creep mechanism of the rock was discussed using the failure mechanism hypothesis proposed by Bieniawski and by others. On this basis, critical time to failure was predicted by the relationship between the logarithm of life time and stress ratio of the sustained axial creep load. Additionally, outline of the monitoring system of AE/MS activity in the field, which have set by the Ohya Aria Consolidate Public Corporation and the others to predict or to prevent the degradation of those residual pillars, is to be reported. Key words : Ohya-ishi, Pumice tuff, Mine pillar, Long term stability, Creep, Critical time

Jan 1, 1996

By Ted Klemetti

Roof deterioration in weak moisture-sensitive rock leads to roof falls in coal mines. An observation site was set up in intake air at an underground coal mine in central Ohio to evaluate the time-dependent deterioration of moisture-sensitive roof rock. By periodically collecting and weighing the rock falling from the roof, the National Institute for Occupational Safety and Health (NIOSH) was able to quantify the deterioration of the moisture-sensitive shale roof. The measurements showed that more roof rock is falling in the dry winter months. Movements in an intersection were monitored in order to determine if deformation correlated with seasonal changes in temperature and humidity. The rate of intersection roof-to-floor convergence was found to be cyclical and related to seasonal changes, with more convergence during the months of April through September. At the study site intersection, the roof beam did not show deflection indicating movement most likely due to mine floor deformation. The bolt load also increased in the warmer months before shedding load, possibly due to rock failure. Temperature and relative humidity sensors, placed in holes in the roof show that mine air does not mix with the air in the holes. Consistent saturation levels of relative humidity were measured in the holes and it appears that high levels of moisture may have migrated into the bolt holes from roof shales. A roof sealant applied to a portion of the test roof appears to be preserving the roof and reducing the amount of rock fall into the entry, while the screened area virtually eliminated rock falling from the roof.

Jan 1, 2009

By Christopher Mark

A coal burst is defined as the sudden, violent ejection of coal or rock into a mine opening. Coal mines in the North Fork Valley (NFV) of Colorado?s Gunnison River have a long history of coal bursts in a wide variety of settings. These have included longwall and room-and-pillar, development and retreat, and single- and multiple-seam mining. In contrast to other coalfields, where bursts are typically associated with strong, massive sandstone and extremely high stress, many bursts in the NFV have occurred beneath shale roof and some distance from the most highly stressed locations. The goal of this paper is to attempt a systematic study of the entire burst history in the NFV, in order to gain insight into their characteristics and causes. The primary sources of information are the reports of investigations conducted by the Mine Safety and Health Administration (MSHA) Roof Control Division over the past 15 years. This paper provides details on the geologic mapping conducted as part of these investigations, as well as a regional plot of burst locations using a Geographic Information System. The mapping indicates that many of the NFV bursts have been associated with structural features, including low-angled faults and well-defined zones of high-density jointing that exhibit little or no displacement. Some of these features appear to extend for several miles, impacting more than one mine.

Jan 1, 2012

By Theresa M. Bodus

The strength of roof shales is, in part, a function of the preferred orientation of clay minerals within them. Therefore, analysis of clay fabric under both air-dried and hydrated conditions should be helpful in understanding roof shale failure. Core samples were collected from the Energy, Anna, and Lawson shales, which are locally present as roof shales of the Herrin No. 6 coal of southern Illinois. The Clay Fabric Index (CFI) was measured for thirty core samples, using X-ray diffractomtry, to investigate the relationship between clay fabric and roof collapse in coal mines. Greater CFI values indicate a weaker preferred orientation among clay minerals, which generally results in a weaker inter-grain bond. Average CFI values for air-dried samples were: 0.15 for Anna shale; 0.20 for Energy shale; and 0.37 for Lawson shale, .After the introduction of water, average CFI values increased to: 0.28 for Anna shale; 0.22 for Energy shale; and 0.43 for Lawson shale. The laboratory results indicate the following: [l] under air-dried conditions, Anna shale is the most stable, followed by Energy and Lawson shales; and 121 under hydrous (mine) conditions, Energy shale is the most stable, followed by Anna and Lawson shales. In mine environments where roof failures involving Energy shale have occurred, planar trends delineated by a relatively high density of small (0.2-4 cm diameter) iron concretions have been reported along the failure surface. Radial cracks have been observed around unsealed anchor bolt holes in the Anna shale. Instability of the Lawson shale is ubiquitous in coal mines. In the laboratory, similar physical changes were noted in the shale samples after the introduction of water, including [l] increased hydration around the perimeter of iron concretions in Energy shale, [2] radial extension cracks in Anna shale, and 131 extreme slaking of Lawson shale. Measured increases in the CFI reflect the observed physical changes of the samples upon the introduction of water, which probably reflect changes in strength that may result in roof failures in hydrated mine environments.

Jan 1, 1989

By Hani Mitri

Understanding the interaction between rock bolts and underground rock movement is critical for safe and cost effective underground excavation design. Although early research on this subject involved a balance of theoretical analysis and field measurement, recent work has been heavily focused on analytical and numerical studies. This paper describes technologies that have the potential to redress the balance through instrumentation of rock bolts deployed under routine operating conditions in underground mines. Two new products are presented in this paper. Firstly the U-cell coupler is a load cell device that can be routinely coupled to the threaded end of a bolt prior to installation. It measures the ?series? load at the head of the bolt. Secondly, the d-REBAR involves an array of small-diameter, long-base length displacement sensors recessed into grooves along the entire length of the bolt. Both new instruments are interfaced with on-board digital signal conditioning and telemetry. Methodologies for the deployment of the new instrumentation and guidelines are presented for the interpretation of results based on data obtained from field trials. Successful field installations demonstrate the viability and practicality of these new technologies and, moreover, provide important insight in to rock bolt/rock mass interaction.

Jan 1, 2012

By Wenbing Xie

At Renlou Coal Mine, Huaibei Mine Area, the track entry deformed significantly after longwall mining in an overlying multiple seams. The supporting characteristics of primary roof bolts and shotcrete with wire mesh are closely related to the movement of the mine?s surrounding strata. A case study of a track entry deformation was monitored during the longwall mining of a selected overlying panel. The measured data showed the unique entry deformation pattern during the longwall mining in the overlying seam. Underground extensometer measurement showed that entry stability was mainly affected by the periodic roof weighting of longwall mining in the overlying seam. The displacement of the deeper strata occurred a head of the immediate vicinity of the entry. Thereafter, deformation of the roof and floor strata was in the form of shearing of the shallower strata. Due to the use of heavy-duty roof bolting with wire-mesh, the roof-tofloor and rib-to-rib convergences were small, but the floor heave was large, greater than 80% of the roof-to-floor convergence. The measured displacement from extensometers varied with the position of the monitored cross-sections and depth into the roof. There were several deformation patterns, such as shearing movement, compression, and expansion, and the variations between compression and expansion. Strata compression at the entry surface was always accompanied with shearing movement at the deeper strata. During the longwall mining, the whole surrounding strata of the entry moved toward the opening. Underground practical experience indicated that prior to mining, the entry was supported very well in excellent conditions. After mining, however, it deformed greatly. The current entry support technology was not effectively control the severe deformation incurred in entries driven in soft strata due to the following reasons: (1) little is known about the entry deformation behavior of the strata surrounding the opening and (2) the degree of interactions between entry deformation and roof bolting with wire mesh is not well understood. Consequently, effective supporting systems cannot be properly selected to control its deformation and maintain a stable supported surrounding structure.

Jan 1, 2012

By Y. H. Wang

During the last two decades many research projects were conducted to study the load requirements for the powered supported longwall faces (1-6). Significant results had been achieved by these researches. Most of the previous studies were rarely designed to understand the mechanisms of interaction between the supports and the surrounding rock, or to correlate the stress conditions around longwall faces to the mining operations both in time and space. In case of the shield supported faces, the roof-to-floor convergence is very difficult to measure due to the high percentage of roof coverage. The external load on the supports can not be determined from the leg pressure data alone due to the existence of the lemniscate links. Therefore, there is a real need in that a simple engineering method be developed to monitor the variations of roof load on the shield supports, the roof-to-floor convergence and the roof stress restoration in the gob area as the mining proceeds. Only with the results of these measurements, a further understanding about the mechanisms of interaction between the supports and the surrounding rock can be achieved and a criterion of designing or selecting the optimum mechanical parameters of the shield supports can finally be developed.

Jan 1, 1986

By Yi Luo

In dealing with various subsidence cases, accurate predictions of mining induced subsidence are the basis for correct assessment of subsidence influences and subsequent mitigation efforts. There is a good demand for a reliable tool to perform the subsidence predictions and related tasks. A comprehensive and integrated subsidence prediction model, CISPM, developed by the senior authors in the later 1980?s and early 1990?s (Peng and Luo, 1992) is one of such tools. Built on solid mathematical models and calibrated by a large number of collected subsidence cases, CISPM provides a rich set of features needed in subsidence engineering and research works. Its reliability and usefulness have been proven by numerous field applications. This upgrade of CISPM will not only preserve its original features and reliability but also provide some new needed features and a more user-friendly working environment.

Jan 1, 2008

By Axel Preusse

On the basis of the Law on Financing Hard Coal Mining dated 28 December 2007, the subsidized German hard coal mining industry will be shut down to the end of the year 2018 in a socially acceptable manner; in 2012 this decision will be reassessed. Even after the abandonment of all mining activities subsequent burdens are inevitable. In this paper, the possible long-term effects resulting from a mining industry history, which is spanning more than 200 years, and their possible consequences are pointed out, in particular in connection with the abandonment of mine water drainage measures which is economically meaningful in the long term. According to the decision situation as it presents itself today, this point in time will be far beyond 2018. In preparation for this, an action framework is to be developed in areas possibly affected.

Jan 1, 2008

By Peter Zhang

Shield recovery in a longwall move is normally conducted from tailgate to headgate. However, if the face is wide and the immediate roof is weak, difficult conditions with considerable roof sag, excessive shield load, and local roof falls could occur as the shield recovery proceeds to the middle of the face, causing delays in shield recovery. The situation could be aggravated when a pre-driven longwall recovery room is employed. Alternatively, a bi-directional approach for shield recovery, i.e. shield recovery starting from the middle of the face towards both tailgate and headgate, can alleviate the roof sag significantly by quickly withdrawing the shields towards the lower abutment pressure zones at the headgate and tailgate sides. In this case, the bi-directional shield recovery approach was used in a longwall move for a 1450 ft wide face under weak roof conditions. Shields were successfully withdrawn within five days without experiencing significant roof sag. The time-dependent roof-to-floor convergence, shield pressure, and roof conditions were monitored during shield recovery. 3-D finite element modeling was conducted prior to longwall move to evaluate the difference between a uni-directional and a bi-directional shield recovery during a longwall face move. Vertical stress, yield zone in and around the recovery room, load on the shields, and convergence at the center of the shield canopy were obtained from computer modeling, and compared with the data from field monitoring. Finally, the advantages of the bi-directional shield recovery are discussed.

Jan 1, 2007

By Takashi Sasaoka

The PT. Adaro Coal Mine targeted in this research is located in South Kalimantan, Indonesia. The coal production of this mine is increasing year, with about 35 M tons of coal produced in 2006. This mine faces many ground control problems, especially instability of the footwall. Large-scale landslides occur often in the footwall; this may be because of weak rock and the effect of footwall rock weathering. Hence, prompt measures must be developed and followed in order to preserve the stability of the footwall and make this mine safe. Additionally, the final pit design is now being reconsidered because of the increasing demand for and high price of coal. With these issues in mind, this paper describes a solution for improving the stability of the footwall and discusses the final pit design based on the results of an on-site investigation and numerical analysis.

Jan 1, 2008

By R. B. Alke

Request to Mine Beneath Bridge The Jabs Run Bridge is a reinforced portland concrete arch filled bridge located on WV Bouts 7 near Pentress, WV. The bridge has a span of 22.9 m (meters) and a height of 4 m above normal pool elevation to the underside of the center of the arch (See Pig 1). The bridge is a two lane structure with a width of 6.86 m. The structure is over 50 years old Wing been built in 1929 and is owned by the Department (WV Department of Highways).

Jan 1, 1984

By Daniel Barkley

Underground coal mining in Illinois has a lengthy history dating back to the early 1800?s. High extraction underground mining has played a significant role in production through out this time. Modern mechanized longwall mining methods were introduced in the 1960?s and have been in continual use ever since. Regulations governing subsidence from underground coal extraction and the mitigation of resulting impacts to surface structures and surface land initiated in 1983. Despite the history of experience with subsidence, recent plans to longwall in Illinois have stirred public emotions and strong opposition. Anti and pro longwall groups formed and divided a community over the potential economic benefits new mining ventures could bring verses the potential problems associated with longwall mining in productive flat farmland. The debate culminated in a county wide referendum vote on the use of longwall mining. This paper provides an overview of the history of underground mining in Illinois, the controversy that has risen in central Illinois regarding longwall mining, and the efforts to educate the public about regulations that govern longwall subsidence.

Jan 1, 2007

By K. H. Brandt

A standard planning system for the development of roadways was adopted for German coal mines based on the results of geotechnical and rockmechanical investigations. Its goal is to provide for sufficient support systems under conditions of multiple seam mining at great depth. The report points out the required determination of geotechnical parameters and the basis for achieving a high level of planning reliability and resulting high performance in roadway development and longwall mining. The instrumentation and the planning procedure for selecting the support design most appropriate for the geotechnical conditions are described and demonstrated by examples.

Jan 1, 2004

By P. Trueman

A project is underway to convert a validated methodology to a system that will permit the near real time interpretation of loading data from longwall powered supports, allowing rapid adaptation of mining strategies, maintenance scheduling and set pressures for optimal roof control. Such a system has the potential to significantly reduce roof control problems and is a pre-requisite to successfully fully automating a longwall face. The development depended upon a robust methodology for interpreting the pressure sensor data coming from the face in the context of support strata interaction using a novel characteristic load cycle analysis concept. New software was developed capable of handling the large quantity of data emanating from a modern longwall with the current level of signal corruption and loss, accurately delineating load cycles and extracting the critical load cycle features essential for interpreting how the support and strata are interacting. Existing software being used to access the pressure data were found either to be incapable of delineating load cycles at all or, where they could, the accuracy was low, making it impractical to use them in combination with the new advances in load cycle analysis. The software is currently being extended from ?off line? to ?on line? in order to provide a real time response to changing strata conditions.

Jan 1, 2006

By Floyd Varley

In deep and highly-stressed coal mining, advanced design practices are used to minimize the potential for damaging events to occur. Despite these design efforts, the hazard of coal mine bumps can not be completely eliminated. This paper will review current and historic work practices used internationally to minimize the hazard to miners from mining in conditions which could produce a bump. These site specific work practices have a common base in monitoring for conditions which could result in a bump and application of controls to prevent the occurrence or minimize the severity of an event where miners are working. Monitoring practices range from purely observational to semi quantitative. Control methods attempt to initiate events in a controlled manner, absorb the energy of a potential event or reduce the potential for or magnitude of an event by altering the stress conditions of the mine workings. Building from the experiences of other coal fields, an empirical framework to manage the potential hazard of coal mine bumps can be developed to enhance the level of safety provided by prudent mine design.

Jan 1, 2008

By J. Willan

This paper addresses the problem of designing a destress blasting procedure to reduce the incidence of rockbursting in hard rock mines. A review is made of the developed theory and practice of destress blasting in rockburst-prone ground. Specific reference is made to a recent survey of past and current practice with particular reference to Ontario mining operations. The need is identified for a more scientific basis for destress blast design and monitoring. Reference to developments in blasting technology as well as rock mechanics are then made to support a proposed, integrated design procedure and research strategy.

Jan 1, 1984