Search Documents

By A. A. Campoli

A stress control design strategy was developed to minimize the explosive failure of highly stressed pillars, during room-and-pillar retreat mining conducted between stiff immediate roof-and-floor strata. A confined core coal pillar strength model was based on in-mine geotechnical evaluations of successful room-and-pillar and longwall bump control designs. Tributary area and linear shear angle approaches were used to estimate development and gob side abutment pillar loads for supercritical section widths. Subcritical width sections separated by barrier pillars to control stress within total extraction panels were optimized with the boundary element program MULSIM/NL.

Jan 1, 1994

The Kinross DeLamar Mine has been operated for more than 17 years producing precious metals dore' from ores, principally silver bearing with associated gold co-products. In late 1995 a new orebody was commissioned, the Stone Cabin orebody, and the site began a phased shift from silver dominance to gold dominance in terms of precious metals revenue. The Knelson Concentrator was selected to remove gold from a portion of the cyclone underflow stream in the grinding circuit. This paper describes the development of the flow sheet, specific mineralogical impacts on Knelson product and downstream materials, and impacts on mine/mill grade reconciliation.

Jan 1, 1997

By J. A. Halt, E. Larsen

"The Sydvaranger magnetite mine closed in 1996 due to low iron ore prices and was reopened in 2009. The flowsheet has remained more or less as in the old plant, based upon two grinding steps followed by magnetic separation. The magnetite is free of harmful elements and should be attractive on the high quality market. This requires a concentrate containing less than 2% SiO2, which previously was achieved by amine flotation. Amine was preferred because it could be used with sea water. The use of amine is now restricted by the Norwegian Climate and Pollution Agency. Therefore, testwork to replace cationic with anionic flotation was done. Activation of quartz with Ca or Mg ions prior to anionic flotation was shown by research from 1960 to 1980 to be effective under laboratory conditions. The old research results have been followed up in order to make a commercial process for Sydvaranger. Calcium activation works excellently with all Sydvaranger ores, including the ones containing amphibole minerals, but Ca activation requires the high and not environmentally friendly pH of 12.4. Magnesium activation at pH 10.5 is a little more challenging, because the maximum concentration of MgOH+ is about 100 times lower than that of CaOH+. Fortunately, the major impurity in the main Bjornevatn orebody is quartz, which responds well to Mg activation. The process does not appear to depend much upon water quality, as the silicates may already be activated during grinding and magnetic separation in recycled water. The new process is environmentally friendly, as only well-known household reagents are used; oleic acid or tall oil, dextrin, sodium hydroxide and magnesium chloride at pH 10.5.IntroductionThe processing plant of Sydvaranger Gruve AS (SVG) is located in the port town of Kirkenes in the northernmost part of Norway, 10 km by rail from the high-grade deposit of Bjornevatn. This plant has been able to beneficiate magnetite ore to up to 99.5% purity, as described by Sandvik and Malvik (2001). Using the magnetic properties of the ore and making the most out of its enviable liberation characteristics, the original plant consisted of ball mills and 600-mm magnetic separators. The plant was shut down due to market conditions in 1996 but reopened in 2009."

Jan 1, 2015

By M. U. Khan, A. D. S. Gillies

"Diesel exhaust is a major cause of large number of occupational diseases. Acute and continuous exposure to Diesel Particulate Matter (DPM) can cause numerous health issues including respiratory disease, reduced lung capacity, heart disease etc. The National Institute of Occupational Safety and Health (NIOSH) and the International Agency for Research on Cancer (IARC) consider diesel engine exhaust as carcinogenic. In large underground metal and nonmetal mining operations, regulatory compliance regarding miner’s exposure to airborne particles especially DPM is a big challenge. Complex mine networks add more difficulties in controlling DPM. MSHA relies on the NIOSH 5040 method for DPM compliance. The NIOSH 5040 method is a shift average based method which inherits some limitations. Due to these inherent limitations of the NIOSH 5040 method the concept of real-time DPM monitoring is promoted in the mining industry. Several real-time DPM monitors have been used by the researchers and efforts still continues to improve their measuring techniques and understanding. Real-time monitoring of DPM is vital to gain understanding of rapid changes in the mine atmosphere. The current study highlights the advancement in real-time DPM monitoring and mainly covers a review of several studies in which DPM concentrations were measured by utilizing real-time DPM monitors. INTRODUCTION Ventilation of underground mines is an important aspect of mining operations. Mining is a continuous activity and the ventilation networks in modern mines change with extended developments. Proper understanding of the ventilation network is a key design factor of an optimum mine ventilation plan. An important task of underground mine ventilation engineers is to provide clean air with sufficient quantity to the underground miners (Khan M. U. and Gillies A.D.S. 2015). The amount of fresh air supplied to the mine should be adequate to dilute the concentrations of contaminants present in the mine atmosphere. In the United States it is estimated that diesel powered equipment is used in thousands of mining operations (Stephenson D. J. et al. 2006). Use of diesel powered equipment is an attractive option in underground mines due to its several advantages over other available alternates. Diesel engines are rugged, dependable and fuel efficient (McKinnon 1999). It is common for diesel engines in heavy duty trucks to have a life of 1.6 million kilometers (McKinnon 1999). Looking at the developments in other energy alternatives, it can be assumed that the underground mining industry will maintain its reliance on diesel powered equipment (Anon 2001). DPM is an important source of mine air contamination in many non-gassy underground mines (Khan M. U. and Gillies A.D.S. 2015). Diesel exhaust is harmful for humans. Acute and continuous exposure to diesel exhaust concentrations can cause several health issues. Some of the health diseases caused by DPM exposure are respiratory diseases, reduced lung capacity, heart disease, and lung cancer (National Research Council. 1981, Mine Safety. 2005). In addition, NIOSH regards diesel exhaust as “potential carcinogen” (Centers for Disease Control 1988) and IARC has declared that “diesel engine exhaust is carcinogenic to humans” (IARC 2012). NIOSH has also declared that the reductions in DPM exposure would reduce cancer risks (Centers for Disease Control 1988)."

Jan 1, 2016

The implementation of NAFTA in January of 1994 was expected to have small but beneficial effects for the Mexican economy, mostly through increased investment flows. Mexico's mining industry was especially likely to benefit, as mineral investment funds would be diverted to the now safer Mexico and away from similarly endowed but more risky Latin American mineral economies. The results of the past two years have shown that it is governments and macroeconomic factors that influence investment flows, rather than the fine-tuning of trade flows through so called "free-trade" agreements.

Jan 1, 1996

By N. S. Tanious

This work was completed prior to the author's appointment with the Nuclear Regulatory Commission (NRC). Therefore the views and conclusions contained in this paper are those of the author and should not be interpreted as necessarily representing the official policies or recommendations of the NRC. Reference to specific brands, instruments, or trade names is made to facilitate understanding and does not imply endorsement by the author or the NRC.

Jan 1, 1987

By E. O. Strahl

In the search for economic mineral deposits, the need for efficient mineral or chemical assays is of prime importance. Costly analytical methods and long delays in obtaining assay results severely limit the effectiveness of an exploration program. The assay problem becomes acute once a potential ore body is located and large numbers of samples are generated in close interval drilling programs. In order to avoid the delays and high costs of extensive assays, the exploration geologist or mining engineer is likely to be required to curtail his drilling program, composite samples, or restrict the required analyses to a limited number of critical elements. As a result, the definition of the potential ore body may be less than needed for final economic evaluation. The assay requirements for bauxite exploration usually involve a considerable number of total elemental and empirical analysis. Since the Bayer process for extracting alumina from bauxite involves the selective dissolution and reaction of specific minerals from the bauxite, a direct chemical analysis for elemental composition yields only a portion of the data required to effectively describe the potential economic value of ore body or deposit. To fully characterize the economic value of a bauxite requires digestion, mud separation and mud settling tests under conditions approximating a commercial Bayer plant. A close approximation of the process behavior of a bauxite also can be calculated from a combination of the chemical and mineralogical analyses. By determining the elemental chemistry, mineralogy, and Bayer plant processing characteristics of a few samples of a given bauxite, correlations can be derived that permit defining a bauxite in terms of a given set of process conditions.

Jan 1, 1977

By Allan R. Ide

It is a great pleasure for me to speak-before such a prestigious group as the American Institute of Mining, Metallurgical and Petroleum Engineers. The substance of my talk today is the handling of coal and petroleum coke: their characteristics and environmental problems, and how we were able to correct the problems, prescribe the cure and enjoy the benefits. When coke first became a by-product derived from the oil refineries everyone would have been very happy if someone had offered to take this pro- duct off their hands. Unfortunately, there was no market at that time, and no one seemed interested. Soon thereafter, it became a sellable product and began to be shipped to many countries in the world. This was when all of the pollution problems began. I will be talking briefly about some of these problems and showing a short film on this subject afterwards.

Jan 1, 1984

By Charles E. Michener

This paper deals with the occurrence of basic and ultrabasic rocks and their relationship in space and time to major structures of the earth. In order to introduce the paper properly, I must go back a little and try to put the subject in perspective. In the brief time that geology has been a scientific occupation, ore deposits have been grouped and classified in various ways depending on the theories that happened to be popular at the time. Some of the early scientists said that ore came from fire, other schools argued that ore originated from water. Then came the lateral secretionists and in later years the hydrothermalists led by the Lindgren school and the latter has largely been accepted as the modern concept of ore deposits. It now seems apparent that the hydrothermal school is being seriously challenged by other schools of thought. It also seems that we have reached the point where we should be willing to admit that we do not really know in most cases how the ore got to its present position. However, for practical purposes, we can classify ore deposits as to the environment in which they do occur. This is not difficult and gives the field geologist and the mining engineer something to work with and to believe in, and it gives them a basis for carrying out their field work. On the screen, Figure 1, there is a classification of ore deposits based on the environment. Under each classification is listed the more prominent metals which are characteristic of that

Jan 1, 1971

By K. P. Chong

Fracture toughness of oil shale is an essential property in fragmentation to optimize particle sizes and permeability distributions in in-situ processes. Fracture mechanics of oil shale has been based on conventional fracture mechanics using notched samples and assuming the material to be isotropic and elastic. Oil shale is a layered material more accurately characterized as transversely isotropic. The senior author proposes to use a semi- circular core specimen with a center crack subjected to three point bending. Singular crack tip elements with isoparametric elements are used. The precracked semi-circular disk is modeled under displacement loading. The effect of crack length on the non-dimensionalized stress intensity factor is investigated by strain energy method, ellipse method, and stress method. Very close agreements are found. The fracture toughness is obtained by compressing the specimen in to failure. Parameters such as oil yield are investigated.

Jan 1, 1984

By B. J. Timmons

An initial point that I would like to make very emphatically?and as our title might erroneously suggest for those of you old enough to remember . . . Peter Harben and myself do not intend to shoot ourselves in the foot. We derive our livelihood from a number of aggregate, industrial and other minerals producers, both here in the United States and outside. This paper, therefore, is a fence-straddler or for information purposes (we hope) only, rather than any "fur or agin" stances. In essence, some of you may consider it a U.S.G.S. publication! In fact, we hope that it serves to inspire aggregates producers to do some radical thinking, to promote introspection, and to that end it would benefit both domestic and foreign producers. The title could be shortened into a brief question of "Aggregates Travel?" with an emphatic no for the answer. In the past, the success of a construction materials venture depended upon your ability, through siting, to provide the customer f.o.b. the job site, a product at the lowest possible cost.

Jan 1, 1987

By Harold L. Lovell

Problems associated with fines (minus 6 mm, 1/4-inch) production, preparation, and utilization have long plagued the coal industry and are now more acute than ever. Continuous deep mining systems create more fines which have moisture; content greater than natural levels from dust control spraying and often add substantial levels of mineral matter due to mining selectivity constraints. Frequently, during preparation, more -fines are developed to achieve improved component liberation. Coal consumers often specify small sizes whether for carbonization, combustion, or conversion. Wet beneficiation systems process fines by several' types of unit operations, but usually must also incorporate costly and complex dewatering systems to reduce the moisture content of the products. Existing pneumatic preparation systems are constrained between product equality and yield by the sharpness of separation. These limitations become more severe with decreasing particle size and increasing feed moisture content. Control of particulate emissions, both process and fugitive, during pneumatic preparation, can be forbidding. A pneumatic preparation-process which would overcome these constraints, could be most enticing. The DryFlo system is being evaluated to quantify performance characteristics as regards these constraints.

Jan 1, 1976

By D. R. Nagaraj

Adsorption of sulfide collectors such as xanthate on pyrite has been studied extensively over several decades using a wide variety of techniques. In spite of this, there are unanswered questions as to the identity of adsorbed species on pyrite surfaces -dixanthogen vs. iron xanthate complexes. Far less is known in non-xanthate collector systems. We have used Secondary Ion Mass Spectroscopy (SIMS) successfully in the past to obtain direct evidence for the identity of the adsorbed collector species on copper sulfides, galena and Cu-activated quartz. The present study is an extension of the SIMS analysis to investigate the adsorption of xanthate, dithiovhosphate, dithiocarbamate, and modified thionocarbamates and thioureas on pyrite. Adsorption of these collectors on chalcocite was also studied for comparison. An attempt was also made to obtain SIMS spectra for pure dixanthogens at room temperature. Only in the case of dithiocarbamate (DTC) was there direct evidence for the presence of not only the collector dimer, but also iron-DTC complexes. On chalcocite, only the copper-DTC complexes were detected (no dimer). In the case of xanthate, the collector molecular ion and its S adduct -which are possible fragments from dixanthogen -were detected on pyrite, along with a fragment peak: suggesting Fe2X. For dithiophosphate, the collector molecular ion and Fe(DTP)(OH) complex were detected (no dimer). For modified thionocarbamate and thiourea, adsorption on pyrite was negligible.

Jan 1, 1997

By R. H. Hanewald

The processing of EAF baghouse dusts from both the specialty steel industry and low alloy producers will be reviewed. In addition, the INMETCO process has been modified so as to recover nickel, chromium and iron from many other waste materials such as pickling solutions or filter cakes, spent nickel and chromium plating baths, carbon refractories from pickling tanks, and super alloy wastes including baghouse bags. INMETCO is the only North American company presently capable of recycling nickel-cadmium batteries by high temperature metals recovery. This, along with the details of INMETCO's BDAT Test Program and results performed to pre-agreed standards with the EPA will be discussed.

Jan 1, 1992

By G. V. Henderson

The San Gabriel Valley contains some of the richest and most extensive sand and gravel deposits in California. Operating quarries within the San Gabriel area mine more than 15 million tons of high quality aggregate per year. This represents about 45 percent of the total mined in the greater Los Angeles area, one of the nation's largest aggregate markets and producing regions. Popular opposition to continued aggregate production in the San Gabriel Valley is high, especially in the city of Irwindale where 40 per-cent of the city's property is made up of "excavated holes," some 150-200 feet deep. Reclamation of 70 years of mining is now an almost impossible task. Zoning regulations have the effect of depleting these vast reserves rapidly by changing the definition of total reserves to include only "legally minable reserves." All but two or three of the aggregate mines now operating will be depleted or zoned out of business by the year 2000. Some studies indicate that there will be no aggregate mining operations by 1995. Recent studies show a drastic change in land use patterns within this valuable mineral resource area over the past 20 years. The San Gabriel Valley is a classic example of the lack of adequate regional planning with regard to urban development in MRA's and represents a "too little, too late" effort by local government and industry.

Jan 1, 1978

Anomalous geologic or stress conditions ahead of the longwall face can cause great harm to both the individual miner and the mining operation as a whole. The U.S. Bureau of Mines has been developing seismic tomography techniques to image the panel ahead of the face. This paper presents the results of a field effort in which a 60-m (200-ft) segment of a longwall panel containing a fault zone was surveyed daily as the face approached. Stress distribution, geologic structure, and dynamic elastic properties within the panel were plotted and compared to static laboratory measurements. The surveys successfully imaged an anomalous stress concentration, likely influenced by the presence of the fault zone. The calculated dynamic physical properties generally agreed with laboratory measurements.

Jan 1, 1995

By Y. C. Guan

In an attempt to replace the traditional cyanide process of extracting gold, a new technology using ammoniacal solutions has been developed. In this study, the electrochemical behavior of gold in ammoniacal solutions at temperatures above 100°C has been investigated. An electrochemical cell in an autoclave has been introduced to carry out this study. The system consists of a gold working electrode, a platinum counter electrode, and an external saturated calomel electrode (SCE) which is connected to the autoclave system through a Birch wood plug. Techniques used in this study included potentiodynamic polarization, galvanostatic polarization, cyclic voltammetry, and Tafel polarization. The electrochemical reaction mechanisms governing the dissolution process are presented.

Jan 1, 1996

Mine design and selection of ore processing capacity depend upon a correct estimate of the grade-tonnage distribution. The estimate must reflect what can be recovered and processed. The McCoy/Cove operation in central Nevada, USA, is a gold and silver mine. Case studies of recoverable reserve estimation for gold and silver were made using multiple indicator kriging and the log-affine variance correction. From this model, the grade-tonnage distribution was constructed. Optimal pits were generated by utilizing the distribution, and the results were compared with the pit generated by ordinary kriging. Studies indicate that the proposed method for multi-metal recoverable reserve estimation is more accurate than ordinary kriging in terms of both tons and the grade. Using recoverable reserves for mine design will maximize global recovery of mineral resources.

Jan 1, 1997

By A. Pezzuto

"Pipes are used on mine sites in a variety of applications including transport of slurry, conveying clean and processing water, and in mine dewatering. Mine waters and slurries can cause pipe wear and failures via several mechanisms (or combinations thereof) such as abrasion, scaling, and corrosion. Polyethylene (PE) pipe materials have grown in popularity over the past several decades due to their chemical and mechanical properties (e.g., inertness, flexibility, relatively low density) and low cost. While PE is generally resistant to corrosion, it is subject to abrasion. To combat this, a novel, rubber-like liner is in development. In addition to comprehensive abrasion testing, however, the liner must be evaluated to see how it performs under other conditions. Here, a brief field study is described that tested PE pipes with the new liner against traditional PE pipes to specifically assess mineral scale buildup. The study was conducted in the Reiche Zeche study mine in Freiberg, Germany in six different locations with varying water qualities and flow conditions. INTRODUCTION Water and slurry conveyance are major operations on and around mine and mill sites, from mine dewatering, to tailings transport, to water treatment processes. Conveyance systems in such applications can include great lengths of pipe materials along with pumps and monitoring instruments, and thus represent significant capital investments. Due to the variability of the physical and chemical properties of water and slurries, pipe materials are subject to a wide range of conditions. These can cause pipe wear and eventually failure leading to serious economic, environmental and social, consequences. While pressure-induced pipe failures (e.g., ruptures or ""bursts”) can be immediate, most failure mechanisms involve gradual processes. Scaling and sedimentation can present major problems for pipe systems conveying highly mineralized waters. Sedimentation generally refers to the deposition of suspended solids, such as sand, clay, silt, or organic matter onto pipe surfaces. This phenomenon can occur due to a decrease in water velocity or particle collisions with the pipe wall. Scaling, on the other hand, commonly refers to the deposition of precipitated mineral salts (including oxides and hydroxides) onto pipe surfaces. Mine waters often have extremely high ion concentrations (i.e., high dissolved solids content) due to their interaction with enormous surface areas of minerals, which are exposed during mining and processing operations (Brown and Barley, 2002). As these waters are transported, slight changes in temperature, pressure or chemistry (e.g., pH or ORP) can cause instability with respect to ion solubility such that salt precipitation begins to occur. “Seed” crystals can rapidly grow and attach to pipes, either due to local surface phenomenon near the pipe wall (e.g., which can promote coagulation) or sedimentation of the precipitated solid. Whether due to suspended or precipitated solids, as the solids begin to stick to pipe walls, “aging” or hardening processes can commence; and the build-up of scale can become self-perpetuating as the scale itself provides an attractive “nucleus” for further attachment of particles or crystal growth (Muryanto et al., 2014). Over time, scale-buildup reduces the effective pipe diameter, which can ultimately result in decreased flow velocity, clogging and, in some instances, bursting (Dirany et al., 2016)."

Jan 1, 2017

By Luis R. Bittencourt

Research efforts have been made to characterize a refractory Brazilian bauxite ore composed basically of gibbsite, kaolinite and quartz. Detailed polished-section microprobe analysis of the unbroken ore has been used to describe the liberation characteristics and the association between mineral phases. The linear grade distributions for selected particle size fractions were determined by means? of a particular implementation of King's Random Fracture Model that uses the exponential model for the distribution of linear intercepts through both dispersed (kaolinite) and continuous (gibbsite) phases. The corresponding volumetric grade distributions were then determined by means of a constrained optimization technique for the solution of the transformation equation. Batch flotation experiments were carried out to determine the kinetics for particles of different sizes and the results correlated with the liberation spectrum for each size class.

Jan 1, 1991