Search Documents

By R. J. Sweigard

One possible alternative for disposal of flue gas desulfurization (FGD) by-products is use as backfilling support material in highwall mine adits. The finite element method was used to analyze the variation of stresses and displacements within and around a highwall adit backfilled with FGD materials. The engineering properties of the rock material and the optimum mix proportioning of the FGD materials were obtained from laboratory tests. Finite element analyses show that, for the case in question, the roof displacement would decrease about 48 percent and the peak stress could be decreased about 58 percent. The study indicates that fairly weak FGD materials can eventually lead to stability of backfilled highwall adits.

Jan 1, 1996

By D. L. Shenck

The Navajo Mine is exclusively a multiple seam surface coal mine located in the northwest corner of New Mexico, and entirely on the Navajo Indian Reservation (Figure 1). It is owned and operated by the Broken Hill Propriety Co., Ltd. of Melbourne, Australia. The mine began production in January 1963 with a long term fuel supply agreement with the Four Corners Power Plant. The 2175 MW nominal generating capacity of the Four Corners Power Plant consumes 8-8.5 mm tons of coal annually. With estimated reserves totaling 1.1 billion tons of strippable coal, only one third is presently committed to the generating station. As development has continued over the years, mining operations have advanced into more complex geologic areas to satisfy the utilities demand for coal.

Jan 1, 1990

By Syd S. Peng

In the past few years, the numbers of underground coal mines in this country using longwa11 mining method have been dramatically increased. In the latest count there are approximately 90 10ngwa11 faces amounting roughly 8% of the total underground production. Meanwhile, shortwall mining adapting longwa11 powered supports to 'coal mining and handling systems in room and pillar mining is also gaining importance in the Appalachian coal field. Although there are only 7 operating shortwall faces so far, indications are that it will be increasing steadily. Modern longwall faces are highly mechanized and productive. One of these key elements that contribute to the success of modern longwall mining is self-advanced powered supports. There are several types of powered supports. Frame type is two sets of one to four hydraulic legs supporting beam-type roof canopy and floor base. However, chock type is more popular and connected to broad roof and base structure. Shield supports were introduced recently but proved to be highly successful (1). A shield support consists of two hydraulic jacks mounted between a base plate and a gob shield. The base plate is hinged to gob shield which is in turn hinged to roof canopy.

Jan 1, 1977

By John Bailey

Stressmap is a program whereby the earth's stress field is charted in detail and utilized for design of mines and mine exploitation. This program is implemented by mapping the attitude (location, direction, dip, and extent) of induced rock ruptures during the process of hydrafracturing drill holes contiguous to mine interest. The program includes utilization of ancillary naturally occurring stress relief signals, They are precipitated because the earth is indeed dynamic and the strata of the crust are continually adjusting to load and/or strain differentials resulting in rock deformation and fracturing. These fracturing adjustments occur as small to tiny earthquakes comparable to Richter magnitudes of one, zero, minus one, and smaller events termed microearthquakes. Obviously, the earth's stress field changes due to continued differential loading and crustal movements; therefore it becomes conspicuously evident that resolving today's stress field as opposed to paleostresses is most important for efficient, economical, and safe mining operations.

Jan 1, 1974

By Fun-Den Wang

In underground coal mines, three types of roof failure (2)*, tensile, local, and shear, occur in the development entries and in room-and-pillar extraction areas. Most of the tensile failures in the roof at the center of the mine opening as well as those local failures due to fracture or jointing can be controlled by roof bolts, trusses, and timbering. However, control of the shear failure at the sides of the roof (or the cutter-roof caving) has not been successful with ordinary roof control methods. The only effective method, when there is an indication of cutter-roof caving, is to use cribs, which are costly and make transportation, ventilation, and production difficult. Frequently, the operator allows the cutter roof to cave and then cleans it up rather than trying to stop it. This shear type of roof failure is often associated with large areas which may progressively involve several hundred feet of roof caving at one occurrence. At times, this shear failure occurs suddenly with little or no warning. This can result in buried equipment and great danger to the safety of personnel. This shear failure may be due to one or more of the following: high stress concentrations at the corner of the roof from (1) high horizontal to vertical load ratio, (2) orthotropic elastic properties of rock and coal, (3) greater stiffness of the immediate roof layer than of the secondary roof layer, (4) viscoelastic behavior of rock and coal, and (5) geometry and material properties of the geologic setting. Removing or reducing the high stress concentration should improve the roof stability. The structural analyses of models of two typical

Jan 1, 1972

By G. L. Mowrey

In addition to developing various types of coal interface detection systems, the U.S. Bureau of Mines is actively involved in developing a coal rib thickness monitoring system for high wall mining applications. One particular system that appears to show promise uses a ground-penetrating radar system to detect the coal-air boundaries of coal ribs. Based on preliminary laboratory and field tests, results indicate that this method can be applied successfully in highwall mines to maintain a constant rib thickness. The coal seam should be relatively clean in the vicinity of the antenna (e.g., have minimal partings or dirt bands) for best results.

Jan 1, 1995

By B. K. Cantrell

A miner working in an underground coal mine with diesel equipment is exposed to a wide array of pollutants from the diesel exhaust. These include CO, CO2, NO, NO2, SO2, diesel-exhaust aerosol, and a variety of hydrocarbon compounds. A quantitative definition of the health risk resulting from these exposures remains elusive, but during the past several years, progress has been made in defining the problem. Results from epidemiological studies by Garshick, et al. (1988); animal inhalation studies by Mauderly, et al. (1986); Iwai, et al. (1986); and Brightwell, et al. (1986); and in vitro studies by Lewtas, et al. (1986), have provided sufficient data for the National Institute of Occupational Safety and Health (NIOSH) to recommend that "whole diesel exhaust be regarded as a 'potential occupational carcinogen,' as defined in the Cancer Policy of the Occupational Safety and Health Administration," NIOSH (1988). NIOSH further stated that "though the excess risk of cancer in diesel-exhaust-exposed workers has not been quantitatively estimated, it is logical to assume that reduction in exposure to diesel exhaust in the workplace would reduce the excess risk."

Jan 1, 1990

By N. B. Aughenbaugh

Compacted clays are used as permeability barriers in many mineral engineering projects such as heap leaching, containment ponds, tailings disposal and earth dams. Source materials used for clay liners include a wide variety of sand, silt and clay admixtures that exhibit dramatically different engineering properties when densified. The permeability and plastic properties of fine-grained soils are reviewed with respect to the state of compaction as the water content varies. Be-cause they are weak in tension, compacted clays are susceptible to cracking when subjected to differential flexural movements. Designs of compacted clay liners must include an evaluation of their flexibility which is the ability of a fine-grain soil to bend plastically without cracking. This paper will also discuss the importance of flexibility with respect to soil types, compaction effort, failure mechanism and testing evaluation to the performance of clay liners in preventing seepage of pollutants from a containment site.

Jan 1, 1990

By Guy Bridges, Elton Ko, Cheng Ting Ning, Owen Ng, Giovanni Chang, Robert Anderson

"PROJECT OVERVIEWThe Liantang/Heung Yuen Wai Boundary Control Point (BCP) and Associated Works will be the seventhland crossing between Shenzhen and the Hong Kong Special Administrative Region (HKSAR) of China.The project includes site formation of about 23 hectares of land for the development of the BCP and anapproximately 11-kilometre (km) long dual two-lane trunk road (the “Connecting Road”), connecting theBCP with the existing Fanling Highway. The route alignment is within a relatively rural area of HongKong, with very limited similar infrastructure works carried out nearby. It passes beneath bothmountainous terrain, and alluvial plains, and falls within an area of several major regional faults andassociated metamorphism, resulting in a complex variety of ground conditions.ALIGNMENTThe Civil Engineering and Development Department of the Government of the Hong Kong SpecialAdministrative Region carried out extensive public engagement in selecting the alignment of theConnecting Road. Over 70 consultation forums with public bodies, including the District Councils, RuralCommittees, local representatives, etc. were held during the alignment design process. In order toalleviate the concerns of various nearby villages, and to minimize land clearance and environmentalproblems, the original alignment of 10 km long (3.5 km of tunnels and 6.5 km of viaducts) was revised toits final alignment of 11 km long which comprises 5.7 km of tunnels, 4.3 km of viaducts and 1.0 km of atgrade roads.The finally adopted alignment commences at the southern end with an interchange with the existingFanling Highway, part of Route 9, which is a dual three lane expressway currently being widened to dual4 lane. Alongside the expressway is the main rail connection to the mainland of China, and theinterchange viaducts connecting to the southern portal of the Lung Shan tunnel must cross over thisrailway. The southern portal is located in the foothills of Lung Shan, and the 4.8km long tunnel is alignedin a north-northeasterly direction. The southern half passes under mountainous terrain of Lung Shan,and then crosses a valley containing the Kwan Tei river. The northern section comprises low hillsseparated by an alluvial plain and Tan Chuk Hang village area. At the northern end, the tunnel turns tothe north-west to connect with Sha Tau Kok road, an existing single carriageway road, with a newroundabout interchange. Mid-way along this tunnel there will be a ventilation building, connected to the main tunnel by a 330m long ventilation adit. To the north-western side of this interchange is the900m long Cheung Shan tunnel, and after this the remaining 4.3km of the highway connecting with theBoundary Control Point is to be constructed as an elevated viaduct. The alignment is shown in Figure 1."

Jan 1, 2016

By John J. Simmons

Federal and state regulations, in an effort to reduce acid rain, are becoming increasing more stringent regarding sulfur content of fossil fuels. Whereas coal from Illinois and Ohio contains between 1.5 and 37. sulfur, Wyoming has billions of tons of coal reserves containing less than O.5/% sulfur. However, much of Wyoming's coal is high in moisture, 25-30%, and low in energy, 8,200 to 8,900 BTU, vs. 10,500+ BTU for Illinois and Ohio Basin coals. Wyoming currently ships in excess of 130 million tons of coal to utilities as distant as Michigan, Wisconsin, Minnesota, Iowa, Nebraska, Louisiana, Oklahoma, and Texas. With freight charges ranging from $12.00-$20.00/ton, more than $1.5 billion a year is spent to transport water. A test shipment of more than 50,000 tons of Wyoming coal has recently been made from Mobil's Cabello Rojo Mine, south of Gillette, by Burlington Northern to the Robert's Bank British Columbia coal terminal for transloading and shipment to Taiwan Power Company. This coal assayed approximately 8,400 BTU/lb. and 277. moisture. Carbontec Energy Corporation feels the future availability of dried coal containing 11,000+ BTU could substantially enhance the potential export as well as the domestic market for Wyoming coal. Large and small utilities, along with industrial furnaces require tens of millions of tons of Wyoming, West Virginia, and other Eastern The federal government is encouraging the expenditure of hundreds of million of dollars by utilities to retrofit their boilers to allow them to burn higher sulfur coal. This program, if carried to completion, would cost many tens of billions of dollars, with the net result being high power costs sustained by the utilities. These costs will be passed on and paid for by the American consumer. A sensible alternative would be the burning of low sulfur coal by the utilities, without costly capital and operating expenditures. Carbontec Energy feels the successful operation of a Carbondry Coal Drying Plant in Wyoming will be the forerunner to other similar and larger operations in the State. CARBONTEC RESEARCH The activities of Carbontec's personnel to develop a viable process to dry sub-bituminous and lignite coal goes back some 14 years; in fact, for some of us it goes back to 1962 when we were involved in a program under which lignite coal from Truax Trayer's Velva mine was placed in low sulfur coal, which are burned alone or blended with high sulfur, Midwestern coal. Carbontec believes that a high BTU. reasonably priced, shippable coal fuel produced in Wyoming and delivered at costs competitive with Eastern low sulfur coal, could offer substantial benefits to Wyoming coal producers, utility customers, and to the State of Wyoming.

Jan 1, 1989

By A. Warren Wilson, Hugh R. Wilson

This paper describes the evolution of the Waste Management Program at the Lupin Mine through the years 1982 - 1986. Echo Bay Mines' Lupin Mine is located on the western shore of Contwoyto Lake in Canada's Northwest Territories about 80 km. south of the Arctic Circle. The gold mine commenced production in 1982 and the Waste Management Program was based originally on the total containment concept. Due to an expansion of the mill circuitry and increased throughput, it was apparent that total containment was no longer applicable and therefore studies were undertaken to characterize the tailings, to evaluate the effectiveness of natural degradation of contaminants in the tailings pond and to determine what additional treatment steps would be necessary to meet the requirements of the mine's Water Licence. These studies indicated that arsenic and cyanide concentrations in the tailings pond decant water would not meet Water Licence discharge limits unless certain measures were under taken. As a result of this work, in late 1984 a decision was made to create a two-ponds-in-series system and the necessary civil work was started in 1985. In addition, a series of dykes were constructed to contain the solids portion of the mill tailings in a confined area of the first pond. To remove cyanide, the ponds are operated in a sequential fill and decant mode to take maximum advantage of natural degradation. For arsenic removal, a chemical feed system was constructed for iron salt addition to the decant stream from the first to the second pond. Decanting of the ponds is accomplished by means of a series of 500 mm (20 inch) Sclairpipe syphons.

Jan 1, 1987

By J. Kretschmann, P. Goerke-Mallet, C. Melchers

Mining always leaves a mark behind. Dealing with this legacy is not only a tremendous challenge in Germany, but internationally too. The Technical University Georg Agricola (THGA) in Bochum, Germany, has established a Research Center for Post-Mining. Researchers combine expertise from a variety of technical and nontechnical fields in their quest to shape the post-mining era that completes the mine life cycle. In this respect, the Research Center focuses on four research areas: Perpetual tasks and mine water management, Geomonitoring, Material sciences and site transition. With more than 200 years of successful partnership with the mining industry in Germany and abroad, THGA offers a perfect setting for fresh and sound ideas in order support mining’s social license to operate. The aim of the paper is to describe the Post-Mining Research Center along with exemplary research projects that are of interest to the mining industry globally and to foster technical communication and research networking.

Mar 2, 2022

By W. J. Miles

Diatomaceous earth or diatomite is a sedimentary rock of organic origin that is composed principally of the silicious skeletal remains of diatoms. Diatoms are microscopic single cell acquatic plants that are related to algae. Diatoms first became abundant in the Cretaceous period from about 65 to 135 million years ago. Most of the commercial deposits are of Pliocene through recent age, and are younger than 35 million years. Diatoms are still abundant in present day lakes and seas. The living diatom is supported and protected by two half cell walls or valves united by a connecting band or girdle. These valves are composed of opaline silica extracted from the water in which the diatom lives. After death of the diatom, the silicious remains settle in the lake or sea and accumulate at variable rates approaching several millimeters per year for very active diatom colonies. This accumulation of silicious sediments, after decay of the organism, burial, and uplift, can result in the formation of diatomaceous earth deposits.

Jan 1, 1987

By J. A. Murray

Maintaining satisfactory air quality in electro-winning tankhouses has been problematic and costly, particularly as plant operating current densities have increased. Conventional approaches, including the use of beads, hollow spheres, surfactants and coalescer devices, have not proved completely effective, requiring that powerful ventilation systems be installed. As workplace and environmental regulations become more stringent, containment of the acid mist at its source is more attractive. An electrode cap system based on this approach has been developed and tested in two commercial copper electrowinning tankhouses. The design, development, installation and cost of the new electrode cap system are described.

Jan 1, 1996

By Yuting Xue, Xin Li, Ihsan Berk Tulu, Gaobo Zhao, Deniz Tuncay, Mindi Ruan

Most coal mine roofs in the Appalachian region consist of laminated shale, which is prone to brittle failure. Accurate modeling of shale roofs is vital for studying cutter failures of these shale roofs, and ordinary and formational bedding planes play a significant role in the response off the shale roof to mining-induced stresses. This paper presents a robust method for constructing three-dimensional shale roof models using limited borehole cores and leveraging image processing techniques. The approach begins with image extraction from shale cores. Then, we extract the portions that feature the core and employ image-stitching techniques to merge them seamlessly. Once the images are stitched, they are duplicated horizontally and merged to create a cross-sectional plane image representing a shale roof. This roof cross-sectional plane image serves as an input to our proprietary Digital Image Processing (DIP) algorithm, which is adept at extracting ordinary bedding planes (interfaces that represent color transitions between a single shale unit). The extraction process involves transforming discrete core points (ordinary bedding plane pixels) into continuous lines representing ordinary bedding planes. Finally, extending this method into the third dimension, the model is further extrapolated to form a comprehensive three-dimensional shale roof. Through this process, the geometry information of ordinary bedding planes can be extracted for each type of shale in cores, including sandy shale, gray shale, dark shale, etc. This work bridges the gap between limited core data and comprehensive 3D geological modeling, offering valuable insights into identifying and quantifying the variations in different shale roof geologies.

Jun 25, 2024

By Elżbieta Węglińska, Andrzej Leśniak

The earthquake locations are generally scattered mainly due to a simplified velocity model or seismic event picking errors. The aim of our research was to increase the resolution of the cloud of microseismic events recorded during mining activity in the Bobrek hard coal mine on the 3/503 coalface to delineate seismically active structures using unsupervised machine learning algorithms. We presented results of applying two completely different algorithms for reducing scatter in microseismic location to all events recorded during mining activity on the coalface - the collapsing (proposed by Jones and Stewart in 1997) and condensation (proposed by Kamer in 2015). The collapsing method simplifies the seismic cloud by shifting events inside their error ellipsoids towards local source densities. The error ellipsoids are determined by errors in the measured parameters and seismic network configuration. The advantage of the collapsing method is the partial elimination of blurring of the microseismic cloud. The condensation method reduces the size of the set of seismic events without changing the geometrical information. The reduction of the number of seismic events in the catalog takes place through the condensation of localized events with larger uncertainty into events with lower uncertainty. The spatio-temporal analysis of microseismic events was performed separately on two processed clouds – collapsed and condensed one. We examined how collapsing and condensation methods affect the automatic detection of clusters of microseismicity using density-based spatial clustering of application with noise algorithms. We compared structures detected by the machine learning algorithms in both seismic clouds first created by collapsing and second by the condensation. We identified structures created by mining activity and structures related to the local tectonics activated by mining. The presented results are essential for the prediction of future tremors induced by the mining operation and tectonics and thus ensuring safety in the mine.

Apr 26, 2022

By L. Rintala, P. Latostenmaa, T. Kalliomäki, O. Forsén, I. Lehtiniemi, M. Lundström, J. Aromaa

Conductivity is a typical physico-chemical property that has a substantial effect on electrical energy consumption in the electrorefining process. The objective of this study was to examine the validity of regression models predicting the conductivity of industrial copper electrorefining electrolytes. The models were based on data measured with synthetic solutions on a laboratory scale. The variables included in the models were temperature and the concentrations of copper, nickel, arsenic and sulfuric acid. Both first-order and combined effects of the variables were investigated. The measured data were analyzed using MODDE 8.0 modeling and design software. The validity of the models was investigated by comparing the predicted values with tankhouse conductivity measurements taken at the Boliden Harjavalta Copper Refinery in Pori in Finland. During the tankhouse tests, the conductivity and temperature of the industrial electrolyte were measured, and the composition of the electrolyte was analyzed. The measured conductivity values were compared with the predicted conductivities calculated using the developed models. The conductivity model developed in this paper was shown to be more accurate than previous models and suitable for industrial use.

By W. W. Wen

Approximately 3 percent of the raw coal processed in U. S. Steel coal-preparation plants ultimately reports to slurry- tailing disposal. The usual disposal method is to pump the refuse slurry containing the minus-48 mesh (300 µm) refuse into dams or impoundments that are constructed of the coarse refuse. The failure of an impoundment at Buffalo Creek, Saunders, West Virginia and the sliding failure of a coarse refuse pile at Aberfan, Wales, England, resulted in an evaluation of refuse disposal methods by various regulatory agencies as well as coal producers. The result of this evaluation was the promulgation of Federal regulations dealing with the construction, operation, and final abandonment of coal refuse disposal areas. As a consequence of these regulations the use of the landfill/impoundment method of disposal became in some cases economically urlfeasible or technically impossible. U, S. Steel has studied a number of alternative methods of refuse disposal. During an investigation of mechanical dewatering with a pressure filter, Portland cement was added to the slurry to solidify the filter cake. Because of the success of the cement addition it was decided to study the stabilization of fine-coal-refuse slurry through use of cement-type additives.

Jan 1, 1979

By I. H. Gundiler

Although cyanidation has been universally applied in the processing of gold and silver ores, the search for less toxic alternatives continues. Difficulties encountered in processing ores containing oxidized copper minerals and the inherently slow kinetics of cyanidation have generated a renewed interest in thiosulfate leaching. This process, as well as the catalytic effects of copper ion, were well recognized and widely applied towards the end of the past century. In this study, the effects of copper, ammonia, and thiosulfate concentrations on gold dissolution were investigated using the rotating disk technique. Extraction of gold and silver from an oxidized copper-bearing ore was also studied utilizing a statistical experimental design, and these results were displayed in the form of contour plots.

Jan 1, 1993

By S. Mischler, J. Organiscak, S. Klima, C. Seaman

"Researchers at the National Institute for Occupational Safety and Health’s Pittsburgh Mining Research Division (PMRD) performed comparative testing of six hollow cone water sprays from three manufacturers: static swirl chamber sprays from Spraying Systems (BD-3, BD-5) and Steinen-Hahn (SH-3, SH-5), and movable swirl chamber sprays from Repair King (RK-3, RK-5). Water flow testing was completed at three operating pressures (60, 80, and 100 psig) where both sets of sprays (3-series and 5-series) produced similar water flows, deviating less than 8% from the average water flow rate at each pressure. Airflow induction testing was completed at 80 psig using a hot wire anemometer to take air velocity measurements upstream of the spray nozzles. Respirable dust capture efficiency testing was completed in a 14.5-m3 (512-ft3) closed system dust chamber at 80 psig. The dust capture efficiency ranged from 7.2% to 9.9% for the 3-series nozzles, and from 5.3% to 7.1% for the 5-series nozzles. Sprays were also analyzed using a Cloud Aerosol and Precipitation Spectrometer (CAPS), which uses light scattering to count and size the airborne water droplets from each spray. In both cases, Spraying Systems sprays produced the largest mean droplet size, followed by Steinen-Hahn and Repair King sprays, respectively. INTRODUCTION Coal mine worker overexposure to respirable coal dust continues to be a problem in underground coal mining operations in the United States. The U.S. Mine Safety and Health Administration (MSHA) now requires coal mine worker respirable dust exposure to be no more than 1.5 mg/m3 average over the actual working shift (CFR 30-70.100, 2016). Potential overexposure to respirable dust by continuous miner, roof bolter, and shuttle car operators may be prevented if proper safety and health practices are implemented as detailed in the mine’s ventilation plan (CFR 30-75.371, 2016). Water sprays are a necessary component of an underground coal mine ventilation plan. They are important on the continuous mining unit for moving air and removing respirable coal dust from the breathable airstream. MSHA requires underground coal mines to include the number, types, location, orientation, operating pressure, and flow rate of operating water sprays in their mine ventilation plans (CFR 30-75.371, 2016). Water sprays can become clogged, requiring the sprays to be properly checked, maintained, and replaced in order to continue meeting the ventilation requirements described in the mine ventilation plan.In an effort to eliminate the problems with spray clogging, Repair King has developed self-cleaning movable swirl chamber hollow cone water sprays (RK-3, RK-5). The spray’s movable swirl chamber is designed to only open when water pressure is applied to the spray nozzle, preventing the nozzle from clogging. Anti-clogging sprays could improve mine production by reducing the amount of time spent servicing clogged sprays. Also, these sprays could improve health and safety of miners since they would continue to suppress and capture dust and continue to move airflow at the face, while a clogged spray loses this ability until it is cleaned or replaced manually. The objective of this research was to assess the comparability of the Repair King sprays with the most commonly used sprays in underground coal mines using performance criteria. An assessment of the sprays self-cleaning or anti-clogging capability was not conducted."

Jan 1, 2017