Search Documents

By T. J. Fenner

Surface and underground mining operations are often hindered by unknown tunnels and stopes and the precise locations of adjacent workings. Mine safety and planning are adversely affected especially in previously undermined areas where historical records are incomplete or non-existent. The results of several Ground Penetrating Radar (GPR) studies for the detection of known mine tunnels in underground coal; salt, and gold mines are presented. A case study to locate unknown, abandoned mine workings at a surface gold mine successfully located all workings to a depth of 11 meters.

Jan 1, 1992

By M. A. Cornachione

The west central upper Peninsula of Michigan contains a large resource of graphitic slate. The slate has potential industrial use as a substitute for shale currently used in the production of portland cement. Some of the unweathered slate, however, has a high concentration of pyritic sulfur which can create emission problems when processed in a kiln. A low cost method to reduce the sulfur content of the slate through the optimization of pyrite oxidation in a bio-heap leaching operation was investigated.

Jan 1, 1992

By J. Iannicelli

An entirely new level of magnetic filtration technology was put into full commercial production by the kaolin industry of Georgia, U.S.A. during 1973-1974. At present, four kaolin producers in Georgia are operating large magnetic filters each capable of processing over 1000 gallons of kaolin slurry per minute or over 65 tons of kaolin per hour on a dry basis. A fifth large filter will go on stream in August, 1975. Four of these units are 84" machines manufactured by the Pacific Electric Motor Company of Oakland, California. When operated at the maximum 1000 g, p. m. rate, these five large magnetic filters have a combined capacity approximating the entire waterwashed coating and filler kaolin produced in the U.S.

Jan 1, 1976

By James M. Krese

The West Kentucky Division of Island Creek Coal Company, which is a wholly owned subsidiary of Occidental Petroleum Corporation, operates the new Hamilton Mine. It is located six miles West of Morganfield, Kentucky, in the Northwest section of Union County, adjacent to the Ohio River in Lock 50. On July 15, 1968, a unique new coal conveying system was put in operation. This system consists of eight conveyor units carrying coal from the bottom of the mine slope ultimately to barges on the Ohio River. It is over two miles in length and has a total of 3175 connected horsepower. The river loading conveyor is the longest 72" wide conveyor in operation in this country.

Jan 1, 1969

By J. W. Shield

Refractory sulfide flotation or gravity gold concentrates are coated onto a sized support matrix and placed in a heap configuration for biooxidation. The surface coating is typically less than 0.05 in. thick and the support matrix is preferably composed of 0.375 to 0.75 in. diameter material. The exposed thin coating of sulfides reduces biooxidation rate limitations due to oxygen mass transfer. The large spaces between matrix particles reduce resistance to fluid percolation and aeration in the heap. The capital and operating costs for this biooxidation configuration are significantly less than for concentrate biooxidation in stirred tanks. After 30 to 90 days of biooxidation, sub- sequent gold recoveries exceed those seen in whole ore heap biooxidation and are comparable to recoveries obtained from stirred tank biooxidation processes. Results from laboratory and pilot testing indicate that this technology is a viable alternative for pretreating sulfide refractory gold ores.

Jan 1, 1997

By Ray Nivens, Umit Turunc, Caroline Sui, Nick Morrison, Douglas Steiner

"In most copper mines and concentrators, mill water is continuously recovered and reused, with fresh water added to make up for losses. When mixed, these water chemistries can lead to severe scaling, especially in pipes, tanks and pumps on the mill water supply side, reducing flows and causing significant production losses.At KGHM Robinson Nevada Mining Company, increases in the fresh water addition ratios resulted in severe scaling problems and premature pump failures thereby jeopardizing plant production. What initially appeared to be a few isolated scaling events eventually unfolded into a recurring pattern of water supply-related production losses with increasing severity. Through completion of detailed root cause analysis, chemistry modeling, laboratory work, in-plant testing and system engineering, the mechanisms of scaling were identified and addressed.Advancements in fresh water addition practices and antiscalant application methods resulted in a stepwise reduction of the mill water scaling. Cost savings and production benefits were significant to the plant’s financial metrics.IntroductionThe production of mineral and metal concentrates using the flotation process requires large quantities of water. Flotation is utilized as the primary means for beneficiation with sulfide ores. Mined ores are crushed and ground into a slurry of 20-55% solids. For each ton of ore, 400-900 gallons of water1 are needed to supply the grinding mill. Additional water is needed in the flotation circuit as well. With many modern mills operating at2 11,000-165,000 tons/day, water supply volumes can be upwards of 3,000 gpm to 100,000 gpm of flow.For plants operating at or above capacity, disruptions and restrictions in water supply flow can have a direct impact on the production and recovery of the metal. Water supply flow can be limited for a wide variety of reasons but of interest are those limitations that are due to mineral scaling. Mineral scaling is the selective point precipitation of inorganic species above saturation concentrations. Precipitated species form flow-restricting deposits in the mill water system (tanks, pumps, pipe and valves), that will eventually impact water supply to the concentrator."

Jan 1, 2017

By D. V. Bush

There has been a great deal of evaluation and discussion on the economics of semi- autogenous grinding versus conventional grinding circuits. This paper will not discuss the merits of one system over the other, but rather will discuss the Henderson Mill's approach toward achieving the most economical milling conditions in its existing SAG mills.

Jan 1, 1985

By D. R. Spears

Conventional round tank thickeners have been widely used in the mining industry for many years. The mining industry was well satisfied with the ability of conventional thickeners to improve minerals beneficiation operations. However, development of improved flocculants (the polyacrylamides) made possible much more rapid settling rates, since polyacrylamides produce large flocs rapidly (unlike starch or inorganics). Traditionally considered to be a slow operation if maximum underflow density was achieved, and therefore there was some justification for the expense. Thickeners required large volumes to permit sufficient time for settling. The oversize not considered a drawback but the initial capital cost was. In high rate thickeners, a bed of thickened material is allowed to build around the feedwell, even above the bottom of the feedwell. The slurry is fed directly into the bed at a velocity that allows the material to be evenly dispersed over the thickener area This more efficient use of settling area allows a higher solids throughput per unit surface area (rise rate). In this paper, high rate thickener rise rates and polymer consumption are compared.

Jan 1, 1998

By James J. Brady, Kenneth L. Faught, Chadi El Mohtar, Chaoshi Hu

"During construction of a 9.5-ft. diameter sanitary sewer tunnel, the City of Edmonton encountered a large pocket of flowing sand that flooded their TBM and caused significant surface subsidence, stopping further tunneling by the TBM through this zone. A unique collaborative effort ensued between the authors representing the city, consulting engineers and academic researchers to develop the optimal strategy for grouting the problematic soils. The site has a layer of very find sand between 20 and 30 ft. in depth with fines contents ranging from 5% to more than 40%. The collaboration extended from requesting additional site investigation efforts to shipping samples to the UT-Austin laboratories for grout testing plus ground and grouting characterization tests resulting in field recommendations for a full scale ground improvement program. New research information on the grouting of fine sands along with a collaborative framework for the design of in-situ grouting projects are the key topics presented. INTRODUCTION Encountering a large unexpected pocket of flowing sand with an open-faced TBM while excavating a tunnel below the groundwater table is never a good thing. This was certainly true for the City of Edmonton when one of their Lovat TBM’s became inundated by flowing sand while excavating the 9.5-ft. diameter Millwoods Double Barrel Replacement Tunnel in September 2013. However, since the City of Edmonton self-performed this work, a rare situation existed where the site could be investigated objectively, without the prejudice of contending parties selectively influencing how information was gathered and presented, to accurately examine site conditions with a goal of identifying the best remediation measures."

Jan 1, 2016

By Richard L. Profio

A practical analysis of the three basic elements of a mining shovel's productive capacity. Payload Speed Reliability Improved dipper fill factor is explored referring to the latest generation of wide dippers combined with higher "bank horsepower" capabilities of modern drive systems. Cycle time improvement is reviewed including overall attachment geometry and coordination of motions. A specific case study is detailed. Basic reliability of welded structures, machinery components, and electrical systems are related to operating costs. Three basic elements determine a mining shovel's long term productive capacity: 1) Average payload per cycle. 2) Average cycle time; and 3) Reliability. This paper deals with productivity gains that are possible with existing shovels as well as new equipment.

Jan 1, 1984

By P. R. Hervey

Quartz is the second most widely used electronic material, with approximately 3,000 tons of single crystals used each year. Virtually all of this material is synthetic; grown with a technique called hydrothermal growth. We will review the basics of hydrothermal growth, the feedstocks for these crystals, and the challenges to improving the growth process. We will also review the processing of these crystals, the markets and applications where they are used, and the global outlook for these markets.

Jan 1, 1999

By J. E. Garlanger

Each year, Florida mines approximately 40 million tons of phosphorite, most of which is ultimately converted to various commercial fertilizers. The phosphorite is mined from within the bottom portion of the 40-to 60-ft. thick surficial aquifer, using open pit mining techniques. The ore zone or "matrix" is generally overlain by relatively permeable fine sand to silty and slightly clayey fine sand. The ore itself is highly variable in nature but, in Central Florida, typically consists of less permeable clayey phosphatic sands and sandy clays with stringers of permeable sand. The ore is much more sandy in the north Florida mining area.

Jan 1, 1990

By R. R. Johnson

The Hama Mining Company owns and operates The Groveland Mine near Iron Mountain, in the Upper Peninsula of Michigan. The orebody is part of the Menominee Range of the Lake Superior District. The ore (generally known as Jasper taconite) contains an average of 35% iron ranging from 28% to 39% with an overall split of 60% magnetite and 40% hematite. The variations encountered throughout the orebody require a certain amount of blending to reduce feed changes to the mill. One of the variables which affects the crushers, as well as the mill, is the range of hardness which has a low of 7.9 and a high of 24.6 as measured by the Bond Twin pendulum impact and crushing technique. Reference is made to hardness only to point out its effect on crushing and wear rate variations. Over a period of time, these variables do, of course, average out. Mining of the low grade ore started in 1959 and has operated continuously to date. Preparation of the feed for conventional rod and ball mill grinding is accomplished by three stages of crushing. Reduction of crude ore is first passed through a 54 inch gyratory crusher; then through a secondary crusher; followed by two or three tertiary crushers in closed circuit with screens as production quotas require (Figure 1). Current demand to the crushers is about 5,200,000 tons of crude ore per year.

Jan 1, 1976

By D. C. Yang

A packed column jig has been developed for sharp separation of fine particles--150 down to 1 micron--having different densities. The packed jig is a column filled with corrugated packing. A slurry of mixed particles is fed into the middle of the column. Water enters near the bottom of the column as both a steady state and a pulsating flow. The pulsating water sets up a jigging action that interacts with the packing causing the dense particles to sink and exit the bottom of the jig and the lighter particles to rise and exit the top of the packed jig. The result is a sharp, environmentally friendly, gravity separation machine with low operating costs. Grades and recoveries of iron ore exceed that of known devices. Grades as high as 95 percent purity with concomitantly high recoveries are common for iron ore concentration. Low silica, sulfur and phosphate are common. This paper is the first to unveil the packed column jig technology in detail and presents its physical model with performance data. The purification of iron ores and coal is the paper's focus.

Jan 1, 1997

By Leonard H. Hoyle

The American Society of Association Executives is a professional society composed of nearly 10,000 individuals who serve as salaried executives on the staffs of more than 6,500 associations. Represented is the full range of international, national, regional, state and local associations...including trade associations, professional societies, philanthropic organizations and others. The dramatic growth of ASAE during the past 15 years is a manifestation of the growth of the association movement during the past two decades. This is not to imply that associations are a new phenomenon, because they have existed for thousands of years. Ancient civilizations show evidence of groups formed for mutual protection and advancement. In the transition from ancient to medieval time, trade associations and guilds came to serve an important function for the craftsmen and merchants they represented, encouraging the growth of new industries, improved processes and education.

Jan 1, 1981

By E. Poeck, R. Garvey, U. Ozbay, K. Zhang

"A coal bump is characterized by the sudden failure of one or more pillars and an associated release of kinetic energy. Although the geologic conditions surrounding coal bumps are often similar, their occurrence and magnitude are difficult to predict. This paper presents the development of an approach to assess the potential for coal bumps in room and pillar mines through the use of energy concepts and special consideration of the interface properties between the coal and overlying rock. Back analyses were performed on the widespread collapse of a room and pillar mine with an associated 3.9 local magnitude seismic event. Pillar and mine-scale models were constructed using the distinct element method to simulate the mining stages leading up to the collapse. A variety of loading conditions, material properties, and interface properties were evaluated for their effect on unstable failure of single pillars, and the mine-scale model was used to study the evolution of failure during progressive mining. The extent of unstable failure was quantified in these models by calculating the total kinetic energy released during each mining stage. Through the parametric analysis of single pillar models, it was found that softening parameters in either the coal or the coal/rock interface can individually facilitate unstable failure of pillars, but the combination of the two in a single model produced a much higher release of energy during failure. The results of the mine-scale model further illustrated the trend as the combination of softening parameters in the coal and coal/rock interface produced a series of failures which most accurately reflected the collapse event at the mine. The method of room and pillar stability analysis demonstrated in this study effectively explores the potential for large coal bumps. INTRODUCTION The analysis of coal pillar behavior is challenging because natural variability in geologic conditions requires estimation of material strengths and predicted loads for a given mining situation. Large width-to-height (w/h) ratio pillars and deep overburden present an additional challenge, as the failure behavior of such pillars is more complex and may involve unstable, sudden collapse. Empirical methods have improved the success of coal pillar design for a wide range of conditions, but for deep cover and squat pillar geometries, less accuracy has been achieved in predicting pillar performance (Mark 2000). As with any empirical approach, more back analysis and the consideration of new variables may help improve understanding and accuracy of future designs. This paper presents a study of pillar stability through the back analysis of the Crandall Canyon Mine collapse, which occurred in August of 2007. Pillar-scale models are utilized for the calibration of material properties and assessment of potential instability under varying conditions, and mine-scale models are constructed in an attempt to reproduce widespread failure and correlate with observations at the mine. Special consideration is given to the properties of the coal and the coal/rock interface, and kinetic energy is calculated throughout the course of the simulations to gauge the level of instability when pillar failure occurs. Models were constructed using the Universal Distinct Element Code (UDEC) (Itasca, 2014)."

Jan 1, 2016

By K. J. Hartman

The term kaolin is derived from "kauling". a Chinese word meaning high ridge, which was the name of a hill in China where kaolin was first mined several hundred years ago.(1) Other common names used today for kaolin include "clay" and "China Clay". The former word technically has a broader meaning and could refer to various types of clays such as bentonite and ball clay as well as kaolin. China clay, as a descriptive term, apparently results from kaolin's origin as described above but could also be due to a significant historical use in ceramic applications. The terms "kaolin" and "clay" will be used interchangeably in this analysis because of the common practice of using these terms in the paper industry. Major reasons for kaolin's widespread industrial usages center on the mineral's (kaolinite) physical features of good color, low viscosity and inertness. Kaolin is described as a hydrous aluminum silicate with approximate composition Of 2H20.A1203.2Si02. As will be shown later, a new version of the product, calcined clay with modified hydration content, is gaining widespread usages. Components of any particular kaolin in addition to alumina and silica are viewed as impurities. The more valued deposits and, hence, higher priced kaolin products are those of highest purity.

Jan 1, 1986

By T. Tamagawa

A gaseous chlorination process for hydrometallurgical treatment of a chalcopyrite concentrate was investigated. The overall process is visualized to consist of low temperature chlorination-selective oxidation, followed by aqueous chloride leaching and SX-EW for producing electrolytic copper, elemental sulfur and ferric oxide. In this article, the chlorination phase of the processes is described. Initially, the chlorination behavior of chalcopyrite-concentrate micro-pellets was investigated using a small batch-type fluidized bed reactor. The optimum conditions thereby established was used in continuous chlorination tests. The chlorinated products thus prepared were used in the selective oxidation phase of the investigation.

Jan 1, 1999

By Wilfred Walker

Much is known of the geography of the Alpine orogeny because it has now ended and all geosynclines are in their terminal, cordilleran form. The principle of sea floor spreading, continental drift, and mantle cells has gained general acceptance, but the number and position of the cells, even during the Alpine orogeny, is controversial. The oceanographers have demonstrated the uprises and in this paper it is suggested that downflows are marked by island arcs in the oceans and geosynclines (now cordillera) in the continents, for a total of about a dozen cells. Major mineral deposits associated-with the Alpine downflows are porphyry copper, molybdenum, nickel, chrome, lead-zinc-silver, gold, mercury, tungsten, and tin. Amore precise environment is known for some of these metals, for example, nickel, chrome, and mercury in flysch (which flanks mantle downturns), Ten major orogenies have taken place from 3500 m.y. to the present, Their re¬construction and metallogenesis is the subject of a continuing study.

Jan 1, 1971

By T. Klemetti, W. H. Su, M. A. Van Dyke

Entry stability in coal mines is dependent on geologic conditions and engineering controls. Most engineering controls in ground control are predictable and standardized for typical geologic conditions. However, geologic anomalies may exist that are difficult to detect with traditional core hole drilling. Borescopes offer a cost-efficient way to gather more geologic data between core holes. Additional data obtained from borescope results provide a clearer picture to enhance detection of hazardous conditions due to geologic anomalies. The equipment, methods, and analysis of borescope results provide geomechanical engineers with a clear understanding of strata behavior and the best information to implement roof control plans and supplemental support to enhance miner safety and health. INTRODUCTION Borescope technology has changed very little since its inception. However, the idea to use borescopes to examine roof strata started with the U.S. Bureau of Mines in 1979 with the production of a fiber-optic borescope (FitzSimmons, et al., 1979). The first documented use of a borescope in the coal mining industry began during the 1980s in Australia by researcher John Shepherd. Shepherd’s idea was to use a borescope to collect a series of data points from the roof lithology and compose a geologic cross section. The cross section was then used to identify key features that suggested the beginnings of roof failure. The features Shepherd identified were bedding plane separations in the roof and low angle, extension, and tensile failures. Shepherd also suggested that the borescope findings could be used for geologic mapping for lithological variation, fracture distribution, and determining if supplemental roof support was needed (Shepherd, et al., 1986). In the United States the first publication about borescope usage for coal mine stability assessment was by Su and associates in 1999, who specifically related the combination of using borescope, geophysical, and corehole data to produce geologic hazard maps (Su et al., 1999). This work directly linked the usage of a borescope with the design of supplemental roof support. The use of borescopes in mining was adopted industry wide by the 2000s. Operator case studies were being published using borescopes to aid in supplemental support recommendations and hazard mapping. An Australian study published in 2007 based the optimization of secondary support after each longwall pass on the results of borescope data. The study stated that the borescope was an invaluable tool for understanding roof behavior (Black, et al., 2007). In 2009, a publication by the National Institute for Occupational Safety and Health (NIOSH) took the concept of borescoping one step further. The work centered around creating a roof quality index (RQI) for limestone mines based on borescope data. The RQI attempted to assign a ranking to establish the nature of the roof and its stability (Ellenberger 2009). In theory, this would have been a very useful tool, but the RQI system has not been widely adopted in the industry.

Jan 1, 2019