Search Documents

By K. F. Unrug

The identification of the major subsidence areas in the Western Kentucky Coal Field has been made to distinguish the subsidence phenomena on the basis of geographical location Further, this identification process is based upon selected critical geological, topographical, and mining features in the coal fields. The proposed identification of the regions is derived from a comparison of the subsidence potential in a particular area. The most likely severe subsidence areas are compared to those with the probable low subsidence severity. The combination of certain geological and mining parameters involved allows for the derivation of a classification of the subsidence potential. It is recommended that further site specific studies should be performed on this area.

Jan 1, 1986

By Rudolf Voigt

Lignite reserves occur all over the world in different climatic regions. This means, that the impact of the hydrologic regime upon mining activities and, vice versa, of the mining activities upon ground and surface water conditions will be different between any two mines. On the other hand, most economically important lignite deposits can be grouped according to principal depositional and structural features described briefly in the following section. These features do allow a preliminary assessments of the nature of ground water problems which may face the mine. The cost of protection against water which threatens a mine, the environmental impact of the appropriate measures to achieve this end and the restraints of population density which both might exclude the most cost-effective approach will govern the project expenditure for drainage work. Whether or not this expenditure can be borne by the project must be established during the feasi¬bility phases of mine planning. So, the somewhat provoking title of this paper does not mean that its question can be answered once for ever. It should rather serve to bring to the attention of the audience the major features of mine water control.

Jan 1, 1985

By V. Svalbonas

In the establishment of a useful failure criteria for complicated, fabricated structures, two basic areas of knowledge must be evaluated: 1. The accuracy of the applied stress analysis must be known in comparison with actual stresses encountered during mill operation. 2. The metallurgical fracture properties of the basic materials must be established with reference to non-destructive examination (NDE) methods to be used during fabrication. Both of the above can only be evaluated by use of full scale tests on the structures, and/or components, of interest. This paper describes such tests and comparisons as applied to several large mill installations. In addition, weldment component fatigue tests arid flawed casting strain gauge tests are also discussed. The combination of such test results allows for the formulation of failure criteria directly applicable to the fabrication and examination procedures followed in grinding mill structure manufacture.

Jan 1, 1982

By D. S. Parasnis

The early beginnings of mining geophysics in Sweden can be traced back to the reign of queen Kristina in the 17th century. The mine compass, consisting of a freely suspended magnetic needle in a casing, was in use certainly by 1640 and probably earlier for locating iron ore deposits. Whether the mine compass was a Swedish invention or not is an unsettled question since the possibility cannot be overlooked that the celebrated Nürnberg compass-makers of the 16th century may have constructed it for the first time(1). Be that as it may, the mine compass was very extensively employed in Sweden for more than two centuries and met with spectacular success in locating magnetic deposits under shallow overburden. Occasionally the diligent prospector would even be rewarded with a pyrrhotitebearing sulphide deposit, as witness many old sulphide-ore pits and some mines still in operation from the 17th and the 18th centuries. The mine compass measured only the orientation of the Earth's magnetic field and not its strength. Although it was improved in construction and sensitivity over the ages, no great strides were made in magnetic prospecting after the initial discovery of the use of the compass until Gauss, omnipresent in 19th century physics and mathematics, showed with the assistance of Weber how the strength of a magnetic field could be determined.

Jan 1, 1975

By Wallace Macgregor

The direct investment role of Middle Eastern oil producing countries in future world-wide mineral development probably will be a limited one for the next five years. Their needs and their longer range economic objectives substantially preclude any such risk taking ventures. There is, of course, the possibility of political in- vestment. One hears many rumors and doomsday calculations of what the Arabs might do with the rising accumulation of surplus funds. Up to now, this kind of investment has been more in rhetoric than in money. For the most part, oil producing countries of the Middle East have been, and will be, investing surplus funds with strong emphasis on the preservation of capital. They will seek security first and yield second just like any other prudent investor. In several respects, this is regrettable. A direct infusion of risk capital into mineral development, especially in the Third World countries, is a constructive way of enhancing their earning power which many desperately need just to stave off starvation. It would also be a good way of eliminating material shortages in the industrialized world. Most important of all, it would help to ultimately reduce inflation without imposing the hardship of recession. So why isn't it done?

Jan 1, 1975

By J. C. Haptonstall

Stoping methods at the Homestake Gold Mine through 1978 had been traditional overhand cut-and-fill, shrinkage or square set. High costs, low-productivity and safety concerns prompted the mine to search for and adopt a "bulk mining" technique as a primary stoping method. Blasthole stoping had been successful but it is very development intensive, and was not suitable for the mine's accelerated mining program. Vertical Crater Retreat stoping was selected, and today accounts for over 50% of ore production. Case histories representing both the successes and failures of VCR stoping in the mine are discussed.

Jan 1, 1986

By James M. Griffin

It was not many years ago that people would have argued that a coal session did not belong at an International Mining Convention. Historically, steam coal has always been used domestically due to its natural geographic diversity and high transportation expense. Times have changed. With the help of Opec, steam coal has gone international. As opposed to metallurgical coal, whose trade routes have a long history, whose supply sources are more limited and whose market growth is seen by most to be relatively flat, steam coal export forecasts are calling for more than a doubling by 1990 and a quadrupling by the year 2000. Suddenly, one must be familiar with coal mining on a global basis in order to predict which regions will be able to fill these markets.

Jan 1, 1982

By S. C. Suboleski

In a high risk venture such as mining where capital is committed and contracts are signed on the minimum of information, decisions are based primarily on production forecasts derived through consideration of such factors as management-labor relations, mining practice, variations in physical conditions and the equipment applied. Among these factors, the physical conditions offer the least opportunity for control and, due to the wide range of mining conditions that may be experienced, little effort has been made to develop objective methods for measuring their effects on mine out- put. The aim of this paper is to demonstrate a method for assessing these relationships that can be applied under a wide range of conditions both in new mines and in working sections where there is a need to determine the impact of proposed operational modifications. psing empirical data from active underground mines, a mathematical model was developed to derive a set of regression equations for predicting production as a function of mining conditions

Jan 1, 1980

By R. J. Jula

The process of treating granular activated carbon for return to service in the recovery of gold in Carbon in Pulp and Carbon in Leach circuits has been investigated. Carbons from four U.S.A. mines, one Canadian mine and one South African mine were characterized before and after regeneration. The use of thermal gravimetric analyses demonstrated the presence of inorganic compounds on the surface of the carbon. Thermal regeneration was investigated using factorial' analysis to determine the effect or interaction of furnace temperature, retention time and the use of supplemental steam. The operation of acid leaching prior to or after gold elution was investigated. The effect of water quenching, regenerated carbon was also studied. From the data obtained in this investigation, guidelines are given for effective regeneration operation.

Jan 1, 1985

By Rodger C. Smith

The topic chat has been assigned to me ?Economic and Political Climate of the Potash Industry? is a function of two basic facts: 1. Potassium is absolutely essential to plant and animal growth. Along with nitrogen and phosphorus it is one of three major plant nutrients, the three nutrients required in largest quantities for plant growth. 2. United States is unequivocally an "have not" nation with regard to potassium. Quantity of potassium ores is limited and, more disturbing, the cost of production at all U.S. potash mines is marginal in comparison with the major producing countries, i.e. Canada and U.S.S.R.

Jan 1, 1983

By Douglas W. Barr

If some of you have been through the long hot summer in the southwest, you may find it refreshing to turn your thoughts to the wintertime problems of mineral processing in the northern climates. The purpose of this paper is to point out some of the ways in which heat is gained or lost in the tailing basin operation and the problems that can result if too much heat is lost.

Jan 1, 1980

By Robert D. Schmidt

The US Bureau of Mines is cooperating with Cyprus Mineral Park Mining Co., Columbia University, and the US Geological Survey in investigating the feasibility of applying in situ leach mining methods to fracture-hosted, supergene copper sulfide (chalcocite) ores. This paper presents the initial findings of mineralogical, hydrogeological, and geochemical characterization studies conducted at the Mineral Park mine, located in the Wallapai mining district of northern Arizona. A design for in situ leaching is proposed that would minimize the need for blasting prior to leaching, and would enable economical development of deep reserves at the Mineral Park mine. The in situ leaching design would also reduce the potential for long term acid rock drainage.

Jan 1, 1995

By Edwin H. McKee

Eruption of rhyolitic ash-flow tuffs in the area of the McDermitt (Cordero) caldera began about 17.4 m.y. ago and continued for about 1.5 m.y. During this period of silicic eruptions, a circular area about 30 km in diameter collapsed to form a caldera that subsequently filled with sedimentary and volcanic rocks. 3 A total of more than 200 km of silicic rocks was erupted from the volcano. The final phase of igneous activity, about 15.5 m.y. ago, included resurgent doming and intrusion in the central part of the caldera. Three to 4 m.y. later +I2 m.y. ago), hydrothermal solutions using the northern part of the caldera ring fractures as conduits deposited cinnabar, pyrite, alunite, and other minerals in tuffaceous lake beds and volcanic rocks accumulated within the caldera. The ore-forming solutions may have been a residuum from the silicic magma or connate water or ground water heated by the still-hot resurgent magma in the central part of the caldera. The source of the mercury has not been identified. Later oxidation of the sulfide minerals and redistribution of the supergene minerals corderoite, several mercury nitro-oxychlorides, marcasite, iron, and titanium oxides in the sedimentary rocks account for most of the newly discovered ore body at Cordero.

Jan 1, 1976

By R. R. Klimpel

This paper describes four new families of flotation products which are currently being introduced at the industrial level. A brief summary of the chemical basis behind each product family will be given. This is then followed by a selection of flotation examples which illustrate the more important use characteristics that have been observed to date. It is becoming more apparent with further testing that these four new product families can offer both technical and economic advantages to the industrial flotation process operator.

Jan 1, 1992

The Cadia Mine is located 25kms South West of Orange in the central west of New South Wales (NSW), Australia (Figure 1). Orange is a major regional centre with a population of 35,000 people. Cadia has a history of mining and exploration dating back to 1851 and shortly after the first Australian gold rush at Ophir, north of Orange. Newcrest Mining commenced an exploration program at Cadia Hill in 1992. This identified a substantial zone of copper and gold mineralization. Subsequent resource definition drilling defined an orebody with a mineable reserve of 200 million tonnes of ore with an average gold grade of 0.74g/t and 0.17\ copper. A full feasibility study commenced in 1994, approvals to proceed with development were granted in September 1996 and the processing plant was commissioned in July 1998. The project came in on budget at A$440 million and on time, 24 months from design to construction. The estimated operating cost at the time of commissioning was A$8.85/t of mill feed.

Jan 1, 1999

By Barrie C. Butt

The opportunity for an exploration geologist to follow a successful exploration project through the feasibility, financing, construction, development and exploitation phase is rare. In addition, it is not often that the exploration geologist can be present during the mining of a deposit to explain why certain actions were taken or interpretations made and to find out how these interpretations turned out in actuality. At the Woodsreef chrysotile asbestos mine in New South Wales, Australia, mining has been in progress for six years and the writer has been intimately associated with the project during the five years of exploration and the six years of exploitation. The industry is possibly aware of the fact that the Woodsreef Mine has had major production problems, the majority of which have stemmed from the unique characteristics of the ore body and of the fibre. Because of these unique features, a large volume of research has been undertaken by Woodsreef and by other scientific organisations in Australia, England and Canada on the Woodsreef fibre. The answers to some of the problems have negated some semi-sacred concepts of asbestos ore milling and led to the development of new techniques, such as the adoption of microscopic fibre counts as a routine procedure; the modification of accepted evaluation procedures; the development of new machines for dedusting fibres, and to the recognition of a fibre with a unique milling behaviour pattern and, possibly, properties. The problems experienced can be divided broadly into those associated with the geology and those associated with the physical properties of the fibre. It is possible that the same features may manifest themselves in other deposits around the world, and if they can be recognised during the exploration stages a feasibility evaluation may be just that little closer to the actual.

Jan 1, 1978

By William H. Lehr

A 4200 ton-per- hour marine transfer terminal, where river and oceangoing vessels simultaneously exchange cargos of coal and phosphate rock, is now in operation near the mouth of the Mississippi. Its materials handling machinery includes a bucket ladder barge unloader; a rope operated clamshell bucket unloader; a coal loader; and a rail mounted bucket wheel machine. The design and operation of this equipment is described as are the docks and conveying, breasting and barge-haul systems in use at the facility. Design considerations imposed by soil and river conditions, geography, operating needs and investment requirements are discussed. The economic significance of design and shipping innovations introduced by this facility is noted.

Jan 1, 1967

By Brian Stimpson

A recent study by the National Academy of Engineering concluded that if the U.S. Coal Industry is to double production by 1985 it must open 30 new 2,000,000 tons per year surface mines in the eastern states and 100 new 5,000,000 tons per year surface mines in the western states, in addition to major growth in underground mining. Major expansions in coal mining are also planned in other countries. Engineering geology can play an important part in coal mine development, operation and abandonment (Table I), and with the increasing scale of surface coal mining and the requirements of environmental legislation, it seems certain that engineering geology and geotechnics will play a growing role in surface coal mining.

Jan 1, 1976

By Hemendra N. Kalia

Several attempts have been made in the past sixty or so years to commerciliaze the vast oil shale deposits of the United States of America. However, the industry has yet to become viable and economic. To date, it has not been possible to produce oil from the oil shales at a competitive price when compared to the oil produced from oilfields by conventional methods. However, the development work has been quite fruitful in furthering the art of thick bed mining and technology of in situ retorting. The in situ method has the potential of recovering oil from thick beds and the resource recovery potential is much greater than that from underground mining and surface retorting. In situ methods require that the shales/ marlstones be fragmented ' in place to induce adequate porosity and permeability to allow in situ' heating of the fragmented shales. This can be accomplished by using explosives. However, it has been found that the existing blasting systems, though very efficient, are somewhat lacking. The explosive become insensitive when shot in multiple vertical decks. They can also become insensitive when spaced horizontally at close proximity to other charges. Also, since the blasting is done in a very limited free face, this limits the delay time that can be allowed between charges. Consequently it is not always possible to predict the performance of the blasting system on a routine basis. Furthermore, since it is not possible to undertake secodary blasting, it is imperative that the blast design function properly. Recent, successful retorting by Occidental Petroleum Company of retorts seven and eight suggests that some of these problems may have been overcome. This paper addresses some aspects of in situ retorting and problems those have impeded the development of a viable oil shale industry in the U.S.A.

Jan 1, 1983

By James S. Falcone

Soluble sodium silicate materials have well known applications in flotation for desliming, selective depression and corrosion control. Recent advances in the understanding of the complex polymeric nature of silicate solutions using NMR spectroscopy, combined with our studies of the effects of polymeric silicate anions on metal ion activities in solution, oxide mineral surface charges and surfactant adsorption on clays are related to beneficiation processes. The results of these studies indicate the sodium silicates can be used to cause a solution chemistry and particle surface charge characteristics favorable to enhanced effectiveness in typical ore beneficiation systems.

Jan 1, 1981