Search Documents

By M. B. Haggerty, R. J. Sheets, F. Abbasy

To address coal refuse tailings storage needs for a mine operation in western Canada, a feasible solution was to convert excavated open pits into tailings cells. A slope stability investigation and design study were completed to determine the necessary width and slope geometry for in-situ native plugs as the impoundment embankment. The native plugs separate the previous open pit from the current active open pit. This configuration allows for the deposition of refuse tailings in the previous pit while allowing mining to safely continue “downstream” of the temporary impoundment. As mining progresses, each subsequent pit will be filled with refuse tailings; thereby, buttressing the upstream slope of the previous native plug. Although these cells are excavated, and the timeframe for downstream exposure is relatively limited, the native plugs are classified as dams and must be designed to meet applicable safety of dam standards since they impound water and tails above mining personnel in the subsequent open pit. The presentation and paper will discuss the investigation and analysis conducted to develop the geotechnical and hydrogeological design recommendations.

Mar 2, 2022

By Lei Pan, Venkata Atluri, Xuming Wang, Yuesheng Gao, Jan D. Miller

The wetting characteristics and water film stability at the talc surface have been studied, particularly the effect of polysaccharides such as guar gum, starch, and dextrin. Talc is a gangue mineral in the flotation of base metal sulfide ores, precious metal sulfide ores, and platinum group metal (PGM) sulfide ores. Talc surfaces were investigated using surface analysis techniques including atomic force microscopy, high-speed video bubble attachment measurements, and wetting film stability measurements using a synchronized tri-wavelength reflection interferometry microscope (STRIM). In the presence of polysaccharides, there is a significant increase in bubble attachment time at the talc surface, but only a slight change in contact angle, which suggests that polysaccharide depression of talc is due primarily to the slow rate of bubble attachment and not due to a change in contact angle. The critical rupture thickness (hc) for a hydrophobic talc surface was found to be 56 nm, while the hydrophilic phlogopite surface of similar structure has an equilibrium film thickness (he) of 25 nm. At low polysaccharide concentrations, the wetting films formed on the talc surfaces were unstable, but at high concentrations the wetting films became stable with similar thickness values as the critical rupture thickness, and bubble attachment did not occur. However, it was found that the critical and equilibrium film thickness values do not change significantly with the polysaccharide type or concentration. The results from this research help us understand further details of film rupture and displacement during bubble attachment.

By Derek J. Barratt

The existence of a critical size buildup in an autogenous or SAG mill can be predicted from proper examination of drill core and ore samples. Methods of dealing with such critical size in a primary mill are reviewed in the context of ore properties, whether or not pilot plant-scale testwork has been conducted, and also with respect to the design of new plants or the retrofitting of existing operations. The implications of not planning for pebble crushing in situations where it is appropriate are discussed.

Jan 1, 1992

By Emily Adelsohn, Robert Winn, Anthony Iannacchione

"Over 600 longwall panels have been mined in Pennsylvania in the last 50 years. Of those 600 panels, 25 panels undermined interstate highways. Despite this quantity of panels, much is still unknown regarding the detailed effects of undermining highways. The Gateway Mine, the Emerald Mine, and the Cumberland Mine undermined I-79 with 17 panels between 1982–1989 and 2003–2008, respectively; mine Eighty-Four undermined I-70 with 4 panels between 1987–2000.Through the examination of the panels that undermined I-70 and I-79, it is possible to determine which factors have most impacted the highway alignments. In some locations, the highway intersects with panels at angles ranging from 45 to 80 degrees, and at others, it runs between two panels, which simulates the effect of gateroads on the subsidence. The panels width to overburden ratio varies between 0.64 and 1.7, meaning that the interstates were influenced by both subcritical and supercritical subsidence basins. The face advance rates and overburden depths also vary between the panels.Unfortunately, specific information detailing highway impacts associated with unique characteristics of the subsidence basins are limited. However, using the profile function model and influence function model within the Surface Deformation Prediction System (SDPS), the effects of overburden, panel size, and orientation of the road to highway can be indirectly assessed by profile and influence models of subsidence basin formation.INTRODUCTIONCoal mining has been an integral part of Pennsylvania’s history. Room-and-pillar mines have been active since the late-1700s when coal was extracted from outcrops. By 1830, the city of Pittsburgh alone consumed more than 400 tons of bituminous coal each day for domestic and industrial use (PADEP, 2019). In the late 1960s, the face of mining in Pennsylvania changed with the development of full extraction longwall mines. Since that development, over 600 longwall panels have been mined in the Pittsburgh Coalbed in Pennsylvania alone (PADEP, 2019).As longwall mining and other forms of full extraction mining have increased in popularity, the amount of planned subsidence impacting the surface has also increased. The stresses and strains induced by longwall subsidence can cause damage to the surface as well any structures, water supplies, or water bodies that lie above the panel. Since the behavior of soils and structures vary, one way to study the surface effects of longwall mining is to analyze the impact on flat, rigid, pavement surfaces. Examining factors that vary the impact of subsidence with respect to highway alignment can demonstrate the favorable orientation of an alignment to avoid or mitigate damage and critical impact zones in a subsidence basin."

Jan 1, 2019

By K. Louk, E. Gilliland, N. Ripepi, M. Karmis

"Carbon dioxide (CO2) injection in deep unmineable coal seams can enhance coalbed methane (CBM) recovery as well as effectively and permanently store the CO2. Enhanced coalbed methane (ECBM) recovery and CO2 storage capacity can be improved by altering injection parameters including the injection well locations, number of injection wells, and the time and rate of the injection. A sensitivity study was performed with sixteen different injection scenarios on a coalbed methane field in Buchanan County, Virginia to understand the influence of the injection parameters on methane production, CO2 storage and the extent of the CO2 plume. History matching was done for the gas and water production period prior to injection based on field data from an active US Department of Energy funded pilot project. INTRODUCTION The coal structure is a combination of the coal matrix and cleats. In a CBM reservoir, the methane (CH4) is stored in the matrix under adsorption properties, not as a free gas. During CH4 production, the reservoir pressure is reduced and gas is released from the surface of the coal, diffuses through the matrix and transmits to fractures (man-made or natural) via the cleat network. Fractures and cleats are the major parameters that influence gas flow capacity because deliverability of the CH4 to the production well is controlled by the cleat permeability. As gas production continues over time, CH4 desorbs from coal, and coal matrix volume starts to decrease. This volume decrease in the matrix opens up the cleats, matrix shrinkage, which leads to a permeability increase. Several emprical (Harpalani and Schraufnagel 1990a, 1990b; Harpalani and Chen 1995, 1997; Harpalani and Mitra 2010; Pan et al. 2010; Liu et al. 2012; Mitra et al. 2012) and analytical (Palmer 2009; Liu and Harpalani 2013) studies have reported this relationship between pressure and permeability. Those studies showed that permeability is an important parameter in CH4 production performance. Furthermore, during gas production, water is produced through the cleat system as well, therefore gas-water relative permeability must be also considered in evaluating production performance (Gash et al., 1991). In the CO2 injection scenario the opposite occurs because CO2 has a higher adsorption affinity than CH4. CO2 replaces CH4 in the matrix of the coal and increases the volume of the coal matrix, matrix swelling, and results in a permeability decrease. Harpalani and Mitra (2010) concluded in their experimental study that swelling of the coal matrix due to the CO2 injection is two to three times more than the sorption of CH4, resulting in large permeability changes during CO2 injection."

Jan 1, 2016

By James T. Baxter

Underground mining of limestone is becoming increasingly attractive in Illinois. Most quarries are near rivers on the western and southern borders where competition for land use is intensive. Increasing demands for stone can be met by expanded mining with access by edits in existing quarries and by inclines and shafts at downdip sites. Geologic, hydrologic, and engineering conditions indicate that deep mines in the Ste. Genevieve, St. Louis, Salem, Ullin, and basal Burlington Limestones of Mississippian age and in the Moredock Limestone Member of the Dunleith Formation of Ordovician age are possible, but development will require prudent exploration and planning to ensure that the product will be of good quality.

Jan 1, 1978

By P. Guliov

In the first part of this paper the authors present an overview of industrial minerals produced in the Canadian provinces of British Columbia, Alberta and Saskatchewan, and supplied to the Pacific Rim countries. The second part outlines some of the unique opportunities for industrial minerals that exist in the three western Canadian provinces and those minerals we feel have development potential for overseas markets. Because of time constraints, it is not an exhaustive presentation on industrial minerals, but is focused on a few selected minerals that we believe have high potential.

Jan 1, 1990

By Herry Poernomo, Agus Prasetya, Iga Trisnawati, Himawan Tri Bayu Murti Petrus, Gyan Prameswara, Panut Mulyono

We studied yttrium extraction from untreated zircon sand processing waste tailings. Xenotime mineral as the rare earth element source with an abundance of yttrium (REY) was detected in sufficient grade for extraction. As much as 9.03% yttrium exists in zircon tailings (analysed by X-ray fluorescence spectrometry). The presence of yttrium was confirmed by X-ray diffractometry in xenotime minerals, which are yttrium carriers (Y-PO4). The purpose of this research was to determine the effect of leaching conditions on yttrium recovery from zircon sand after alkaline fusion treatment. Alkaline fusion was chosen to decompose phosphate into hydroxide in the xenotimemineral,which will reduce further required hydrometallurgical processing.Alkaline fusionwas carried out for 3 h at 450 °C, with a ratio of sodium hydroxide to zircon tailings sand of ~ 1:1. The alkaline fusion product was leached with water, followed by hydrochloric acid treatment to leach the yttrium. Yttrium recovery reached 87% under optimum conditions (60 °C, 1MHCl, and solid-to-liquid ratio = 1/10 for 7.5 min). A suitable model for yttrium dissolution with hydrochloric acid was diffusion through a solid particle ash layer. The calculated activation energy (EA) for this model was 20.21 kJ/mol.

May 26, 2020

By Gregory Rumbaugh, Christopher Mark

Recent pillar collapses have caused five large airblasts in underground U.S. limestone mines. One of these events injured three miners, but all of them put many other miners at risk. To better understand the hazards, Mine Safety and Health Administration (MSHA) conducted a comprehensive review of the international literature on airblasts. More than 40 airblast cases have been documented, in a wide variety of minerals. Experience shows that miners that are in the direct path of the air as it moves towards the mine exits are at the greatest risk. The paper describes a risk management methodology that can be used to evaluate the level of hazard throughout the mine and aid in the selection of controls to reduce the risk. The paper concludes with a detailed case history of an actual pillar collapse and airblast.

By Yi Luo

Subsidence events occurring above inactive room-and-pillar (R&P) mines, including abandoned mines or sealed portions of active mines, are classified as unplanned subsidence, because of their timing and distribution are unpredictable. When investigating such subsidence cases, many uncertainties exist and disputes often focused on whether the observed structural damages are caused by mine subsidence or other natural or artificial causes. However, solid evidence to identify the cause is often lacking. In order to conduct a complete and impartial investigation, thorough knowledge of subsidence theories and other ground control topics, as well as broad experience, are required.

Jan 1, 2011

By Shailendra Chawla, Ashok Jaiswal, Sonu

Side spalling/skin failure occurs due to the high-induced stress in underground structures. In such cases, rock bolting or other support systems are being used to control the skin failure or spalling of the pillar. The nature of these support systems is passive, which acts during the deformation. These support systems restrict the displacement considerably of the side/or roof surface of the excavation. Ultimately, it improves the stability of the structure because of the increment in residual strength of rock mass. It is noted that these passive support systems give very low confinement in the range of 0–0.015 MPa at the onset of failure. As the level of confinement will be very low and dependent with progress of failure, triaxial test was not found practically suitable. Thus, an alternative procedure of testing has been proposed. In the procedure, sides of sample have been restricted little bit by using adhesive tape. It provides the limited boundness on the lateral direction (LBLD) of rock specimen. The uniaxial compression strength (UCS) test has been performed on 30 numbers of cylindrical rock specimens using the servo-controlled stiff testing machine. Specifically, two rock types (medium-coarse–grained and coarse-grained rocks) were studied in terms of stress–strain behaviour so that a full residual strength envelope for each specimen was obtained. This study reveals that the residual strength of limited confined rock specimens has been significantly increased as compared to unconfined rock for both groups of rock types. The average residual strength of LBLD specimens of fine-grained rock and medium coarse-grained rock has been increased around 12 times, and five times as compared to unconfined rock, respectively. The average peak strength of LBLD rock specimens has been increased in the range of 30.5 to 48.6% for coarse-grained rock. The results of this study have been presented in terms of peak strength, residual strength and Young’s modulus of rock, and the post-peak failure behaviour of rock specimens was also critically analysed through a stress–strain curve.

Mar 21, 2024

By M. K. Mohanty, H. Akbari, L. A. Ackah

Dry separation was the predominant method of coal cleaning in the United States from the 1930s to 1980s. The application peak of dry separators for cleaning raw coal was in 1965, when about 23.1 Mt of cleaned bituminous coal was produced. The main advantage of dry coal cleaning is the elimination RIWKH GHZDWHULQJ VWDJHV DQG VLJQL¿FDQWO\ UHGXFHG moisture in comparison to wet processing. In addition, developed dust control systems have made dry cleaning method an environmentally friendly process. The largest air-based coal cleaning plant was built in Pennsylvania in 1968 and could clean 1,272 t/h of raw coal sized smaller than 19 mm. This was followed by a decline in dry coal cleaning to less than 3.6 Mt in 1988. Some of the main reasons that shifted coal operations IURPGU\WRZHWSURFHVVLQJZHUHWKHQHHGIRUPRUHHI¿FLHQW separations with lower density cuts, increase in raw coal surIDFHPRLVWXUHVSHFL¿FDOO\LQXQGHUJURXQGPLQLQJWRFRQWURO GXVW ¿QHUSDUWLFOHVL]HUHTXLUHPHQWV LQFUHDVHLQ¿QHVLQUDZ coal from underground mines, and health and safety concerns related to dust and noise (Arnold, Hervol and Leonard III, 1991; Miller, 2011).

By D. G. Hartley

The major copper loss at Mount Lyell is in the coarsest particles presented to flotation. An analysis of data collected from the five primary and six secondary ball mill circuits showed that grinding was limited by low breakage rates in secondary mills, possibly due to oversize balls. For 5 months, the make-up ball size for one secondary mill was reduced from 50 to 30 mm. Frequent steady-state tests indicated that overall average breakage rates could be increased by about 70% using smaller balls. A mathematical simulation of the whole circuit with increased breakage rates showed that the resultant finer grind was likely to improve copper recoveries by about 22.

Jan 1, 1981

By Gary A. Nowlan

The Casa Grande West-Santa Cruz porphyry-¬copper deposit is in the Basin and Range physiographic province west of Casa Grande, Arizona (Fig. 1). The Casa Grande West portion of the deposit is controlled by Casa Grande Copper Company and the Santa Cruz portion by ASARCO. The deposit contains at least 350,000,000 metric tons of rock with greater than 1 percent Cu. The deposit is covered by at least 300 m of sediment, with no visible expression of the deposit at the land surface. The deposit is in an area of prime agricultural land that depends heavily upon well irrigation because of a hot and arid climate. Because of the deep sedimentary cover, the chance is extremely remote that the geochemistry of soil or stream sediment would reflect the deposit even if the land surface were not disturbed by many years of farming. Irrigation wells of the area generally bottom in the sedimentary cover. The purpose of the study is to see if the Casa Grande West-Santa Cruz deposit is geochemically reflected in ground waters over and near the deposit.

Jan 1, 1981

By Charles G. Zink

Anthracite is widely known as a domestic or space heating fuel. The prevailing market ratio of domestic to industrial consumption was about 80 to 20 up until 1950. Since then it has been shifting until now the ratio index is about 50/50, exclusive of overseas export. Despite a declining domestic space heating market, the demand for industrial anthracite remains good. However, as a result of stringent air pollution regulations, there is a renewed interest in this low sulphur coal which cannot smoke under any conditions. Anthracite serves other important industries such as power generating, metallurgical, cement, ceramic, chemical, water sewage and industrial wastes filtration. Anthracite is an excellent natural source of carbon and may be utilized in many processes.

Jan 1, 1966

By J. F. T. Agapito

The load carrying capacity of oil shale pillars excavated by conventional blasting, presplit blasting, and mechanical mining is evaluated. The study was based on a comparison of in-situ vertical stresses and fractures obtained from overcoring horizontal holes in the Colony Mine, Piceance Creek Basin, Colorado. Results indicate that conventional blasting causes a zone of damage approximately 3 m (10 ft) thick with low stress distributions. Presplit blasting reduces damage significantly, and increases the load carrying capacity in the 3 m (10 ft) thick zone by 5.93 MPa (860 psi). Mechanical mining causes little or no rock damage, and an increase of 9.83 MPa (1425 psi) in strength in the same 3 m (10 ft) thick zone. An example of pillar design is given showing that the use of presplit blasting and mechanical mining techniques can increase the extraction ratio by at least three and five percent, respectively, as compared to conventional blasting. It is speculated that comparable increases in extraction should also occur due to increases in span dimensions.

Jan 1, 1984

By S. J. Schatzel, J. D. Addis, V. Gangrade, L. L. Chasko, C. A. Hollerich

"A ventilation study using tracer gas was conducted at a western US coal mine. The objective of the study was to evaluate the movement of longwall face air exchanges between the face and worked-out area and to document the presence or absence of face airflow pathways between these locations. The mine operator uses a bleederless longwall ventilation system with a back return and a blowing mine ventilation system. The study was conducted on an active panel and included both underground and surface monitoring sites. The study used sulfur hexafluoride (SF6) released as a slug on the longwall face and in the front of the gob inby the face. The velocity of the tracer gas movement in the gob was 0.019 m/s (3.7 fpm). The rate of movement for the overall tracer gas slug averaged about 0.0091 m/s (1.8 fpm). A separate tracer gas test initiated with the release of SF6 into the legs of the first shield showed the existence of more than one pathway of face air in the general direction from the headgate towards the tailgate corner. Maintaining adequate ventilation air on longwall faces is important for worker safety and for the dilution of methane emitted from the face and caved gob. A more detailed characterization of longwall system air and gas movement allows a mine to better assess its ventilation design for controlling gas on the face and in the gob. INTRODUCTION During a series of stakeholder meetings, a near unanimous concern was expressed related to maintenance of effective ventilation airflow on longwall faces. There was a strong interest expressed regarding the impacts of face length and caving characteristics on the ability to maintain adequate face airflow levels. This study seeks to understand and improve a mine operator’s ability to monitor and control ventilation and methane concentrations across the longwall face by assessing airflow variations in terms of roof caving characteristics and face length. National Institute for Occupational Safety and Health (NIOSH) researchers seek to identify flow paths of ventilation airflow on longwall panels with variations in roof caving characteristics and longwall face lengths. The project research aims to develop an understanding of the role of gas dynamics in variable broken rock, interactions with ventilation airflow and methane concentrations across the longwall face area. The research also addresses continuous ventilation monitoring along the shield line to provide early detection of gas exchanges between face and gob, and thus improve a mine operator’s ability to monitor and control ventilation and methane concentrations around the face. In the context of this paper, the longwall gob refers to the pillared area behind the shields. This work reports on results from one project task to conduct field based research using a tracer gas to describe face air and gob area gas movement in a bleederless longwall ventilation system that incorporated a back return."

Jan 1, 2017

By DeVerle Harris

The enthusiasm with which individuals have participated in mineral exploration in the development of this country testifies to the fact that there was once a very real probability of making a worthwhile discovery. Over the years, the discovery and subsequent exploitation of the accessible ore deposits have made the finding of new deposits progressively more difficult. Present day mineral exploration has evolved from the lone prospector with the grubstaker behind him to a very costly and complex business, involving large sums of money and a staff of experts in the fields of exploration technology. Exploration today must be carried out on a large scale to be profitable. With the involvement of large amounts of capital, there has been a good deal of interest in methods of optimization of the allocation of the resources of a firm 'engaged in mineral exploration. As a step toward this, mathematical models have been formulated which are designed to quantify those variables of mineral exploration in such a manner that they can be integrated with all phases of the firms operations so as to optimize its profit objective or more simply, to make exploration more efficient and effective.

Jan 1, 1964

By J. Baz-Dresch

A custom-designed shotcrete system, consisting of an 8-m3 (10-yd3) transit mixer and a shotcrete spray boom carrier, is used bya 2-man crew to transport and place up to 25 m3 (32 yd3) of steel-fiber reinforced, dry, silica fume shotcrete per II-hour shift. Shotcrete is custom blended by a local supplier and delivered predampened. Mix design and quality control is performed with a computer program that develops and graphs a properly balanced mix based upon the materials sieve analyses.

Jan 1, 1991

By Long An, Chao Wu, Yuanhui Li, Xing Sun, Shuai Xu, Changyu Jin

Stage open stope mining (SOSM) maintains the stability of excavation openings by leaving a large number of rib pillars. Affected by the strong unloading due to stage mining and the low width-to-height (w/h) ratio of the pillars remaining, largescale destabilization disasters of rib pillars or excavation openings easily occur when the distribution of ground stress or the size of rib pillars is unreasonable. In view of these problems, a physical SOSM model test was carried out based on an underground metal mine in Chifeng City, China, revealing the deformation and failure characteristics of the SOSM pillar group by overloading. The physical model test results of SOSM and room-and-pillar mining (RPM) with a weak pillar were compared, and the failure process of the SOSM pillar group showed the characteristics of rapid and severe damage. The strength difference between a weak pillar and the adjacent pillars enhanced the stress rebalancing effect and extended the failure process of the pillar group. Similar to the SOSM pillar group with a low w/h ratio, some high-strength pillars can be used to avoid large-scale destabilization disasters caused by the synchronous failure of pillars.

Mar 8, 2023