Search Documents

By X. X. Shao

Dewatering of ultra-fine clean coal slurry to a low moisture level of20 percent is difficult using the conventional techniques. A novel approach, which utilized mixing of fibrous waste material, such as paper, carpet and wood, with coal slurry prior to dewatering was developed. It was found that addition of about 10 Kg/t of carpet fibers or 5 Kg/t of raw paper pulp lowered the filter cake moisture from 22.5 to 18 percent. The compressive strength of the filter cake improved from 0 to 4.5 Kglcm2 and impact resistance from 0 to 4. The experimental data indicated that the handling character of the dewatered fine coal was improved significantly.

Jan 1, 1998

By F. F. Peng

For a given flotation system, the rate-controlling step in fine coal flotation can be the attachment of bubble to the fine coal particles. The probability of attachment depends upon the surface characteristics and the collector adsorption on the coal particle surfaces. Thus, to further improve the flotation rate and selectivity is to alter the distribution of hydrophobicity on coal particles efficiently by applying the effective means of collector dispersion. In order to enhance the combustible recovery and selectivity of fine coal flotation, and lower the amount of collector used in the fine coal flotation processes, four modes collector dispersion/addition techniques are tested. They are direct liquid addition in pulp (mechanical agitation), ultrasonic energy dispersed collector into pulp, atomized collector into pulp and gasified collector transported by air and formation of collector-air bubbles in pulp. The effect of four collector dispersion/addition methods on the floatability of -600 µ m (-30 mesh US sieve) coal samples from four ranks of coals were studied. The ultrasonic energy dispersed collector and atomized collector flotation processes enhance flotation yield and most significantly improve the kinetics of fine coal flotation. The gasified flotation process can increase the selectivity of separation and decrease the collector consumption due to starvation flotation is achieved in this process. The flotation efficiency of gasified collector process is as high as that of conventional flotation. It is because that the effect of the decrease in the combustible recovery is offset by the increase of selectivity. In addition to flotation experiments, induction times of bubble attachment to the bed of fine coal particles for four ranks of coals are measured.

Jan 1, 1992

By S. A. Elmquist

Research activities performed by Cleveland-Cliffs Research and Hibbing Taconite plant personnel during the last decade have resulted in the development of an improved autogenous mill grinding circuit. Minus one (1) inch autogenous mill trommel oversize material, con-sidered to be a critical size, is magnetically cobbed and then crushed to 100% minus 3/8" prior to reentry into the feed end of the mill. Autogenous mill capacity increases, up to 25%, have been measured in pilot plant tests using this approach and are also anticipated for the Hibbing Taconite concentrator which presently has reached a 15.5% improvement.

Jan 1, 1994

By J. P. McKinney

A mathematical model is presented for the electrokinetic dewatering of suspensions of phosphatic clays. The modeling approach couples a boundary-element model for solution of Laplace?s equation to a recently developed constitutive equation that relates the change in solids content with applied electric field and time. The observation that the electric field controls both the maximum solids content achievable and the time required to reach that value is shown to severely constrain the application of electrokinetic dewatering strategies to an entire clay settling area. The approach, however, may be feasible for implementation as part of a continuous plant process.

Jan 1, 2011

By Stephen H. Stow

Economically important heavy minerals have been studied in the sediments of offshore Alabama and Mississippi. Sandy samples have been collected from a 200 square mile area from Dauphin to Horn Islands. The minerals concentrate in sediments under 10-35 feet of water and may reach 2.4% by weight. The distribution of total heavies is related to the hydrodynamics of offshore Alabama-Mississippi; the greatest concentrations are in the Gulf where the longshore current is diverted from its westerly flow. Preliminary observations indicate that the distribution of individual minerals can be correlated with wave energy, particle size, specific gravity, and morphology of the mineral grains. The coarser, lighter minerals--kyanite, sillimanite and staurolite--are concentrated in relatively low energy areas in the Mississippi Sound and at the end of Dauphin Island in the Gulf; maximum concentration for each is 34.5%, 6.0% and 43.2%, respectively, of the heavy minerals. The smaller, more denseminerals--ilmenite, rutile, leucoxene, zircon and monazite--are concentrated in high energy areas in the Gulf; maximum concentration for each, respectively, is 42.0%, 5.9%, 9.652, 10.7% and 1.3% of the heavy minerals. On the basis of a minimum concentration of 1% heavy minerals, two areas have been identified and the total amounts of different minerals have been calculated to a depth of 25 feet of sediment. The data are preliminary and in no way indicate recoverable reserves, but they do show that on the order of 20 million tons of heavies exist. These deposits should be termed "indicated resources".

Jan 1, 1975

By Gamal Rashed, Zorica Radakovic-Guzina, Khaled Mohamed

"Underground coal mines use mechanical bolts in addition to other types of bolts to control the rib deformation and to stabilize the yielded coal ribs. Limited research has been conducted to understand the performance of the mechanical bolts in coal ribs. Researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted this work to understand the loading characteristics of mechanical bolts (stiffness and capacity) installed in coal ribs at five underground coal mines. Standard pull-out tests were performed in this study to define the loading characteristics of mechanical rib bolts. Different installation torques were applied to the tested bolts based on the strength of the coal seam. A typical tri-linear load-deformation response for mechanical bolts was obtained from these tests. It was found that the anchorage capacity depends mainly on the coal strength. Guidelines for modeling mechanical bolts have been developed using the tri-linear load-deformation response. The outcome of this research provides essential data for rib support design.INTRODUCTIONThe design of rib bolting in U.S. coal mines is based on a trial-and-error process, which is insufficient to eliminate injuries and fatalities caused by rib falls. In the last 10 years, rib failures have resulted in 17 fatalities, representing 52% of the ground-fall fatalities in underground coal mines in the United States (MSHA, 2018). Recently, NIOSH researchers surveyed 90 sites in 14 underground coal mines in the Eastern United States and found that 11 mines are bolting coal ribs, with 4 of those mines using the conventional mechanical bolts and the others using fully-grouted bolts. NIOSH researchers are developing an engineering design procedure for rib support. Pull-out test programs for mechanical and grouted rib bolts were conducted to understand the rib control mechanisms of rib bolts. Only the test results of mechanical bolts are presented in this paper.Mechanical bolt (or point-anchored bolt) is a tensioned bolt anchored down the borehole with a mechanical expansion shell or a resin-grouted medium (Peng and Tang, 1984). The mechanical anchor bolt consists of a plug, a shell anchor, a headed bar with the top end threaded, a bearing plate, a hardened washer, and occasionally a friction-reducing washer. The shell anchor can be either standard or bail type (Figure 1). The standard type shell is held in place by a nut, while the bail anchor uses a strap to hold the shell in place (Peng, 2008). The diameter of the bar is generally 16 mm (? in) for the #5 bolt or 19 mm (6/8 in) for the #6 bolt. The diameter of the hole that the bolt is inserted into must be carefully controlled, since an oversized hole can result in poor anchorage (Moss, 1971). The anchorage is obtained by applying torque to the bolt head, which in turn pulls the plug down in the shell and expands the serrated leaves against the sides of the hole-wall. In the resin-grouted anchor, the resin replaces the mechanical expansion shell at the end of the hole. The anchorage is achieved by bonding between the resin, bolt, and the hole-wall."

Jan 1, 2019

By C. L. Lin

A PC image-based on-line coarse particle size analyzer has been developed to measure particle size distributions under plant situations where overlapped particles are being transported on a moving belt conveyor. Although previous testing had shown satisfactory performance of this image-based system for separated particle size measurements (the non-overlapped case), it was necessary to modify original algorithms in order to solve the overlap problem and make the system suitable for plant operations. On-site testing has been conducted at a large copper concentrator in the southwestern U.S. for further investigation of the overlap problem.

Jan 1, 1995

By F. D. Ayhan

The aim of this study was to investigate desulfurization and de-ashing of a mixture of subbituminous coal and gangue minerals by the agglomeration method. For this purpose, experimental studies were conducted on a mixture containing subbituminous coal, pyrite, quartz and calcite. The effects of some parameters that markedly influence the effectiveness of selective oil agglomeration, such as solid concentration, pH, bridging liquid type and concentration, and depressant type and amount, were investigated. Agglomeration results showed that the usage of various depressants (Na2SiO3, FeCI3, corn starch, wheat starch) in the agglomeration medium has a positive effect on the reduction of ash and total sulfur content of agglomerates. It was found that an agglomerate product containing 3.03% total sulfur and 25.01% ash with a total sulfur reduction of 56.71% was obtained from a feed that contained 7% total sulfur and 43.58% ash when FeCI3 was used in the agglomeration medium. Key words: Desulfurization, De-ashing, Agglomeration, Coal, Gangue minerals

Jan 1, 2009

By S. K. Kawatra

In many mining operations, particularly northern open-pit mines, large seasonal variations in grinding slurry temperature can occur. It is shown in this paper that this temperature shift can cause a winter-time loss in autogenous grinding efficiency of as much as 20Y. if it is not controlled. Laboratory experimentation indicates that much of this effect is due to increases in slurry viscosity as the temperature is decreased. An additional effect may result from changes in rock strength upon freezing, for which possible mechanisms are discussed. However, no effect clearly resulting from rock strength changes has been definitely confirmed.

Jan 1, 1990

By J. F. Colinet, W. R. Reed, J. D. Potts

Dust surveys were conducted at six underground coal mines to determine if deep-cutting practices expose face workers to higher levels of respirable dust. The surveyed mines were able to successfully mine deep cuts without significantly increasing the dust exposures of face workers. In general, all of the selected mines exercised good dust control practices by maintaining water sprays, scrubber airflows, proper curtain setback distances and providing sufficient airflow to the active faces. For exhausting face ventilation, field data indicate that scrubber airflow is the most important factor for controlling dust. Data collected for this study indicate that 20-mesh screens should be cleaned for every 12.2 m (40 ft) of advance, because 22% of the deep cuts surveyed for this study experienced a 20% to 35% decrease in scrubber airflow over the course of the cut. For blowing face ventilation, field data and past research indicate that dust control is aided by maintaining a proper curtain-to-scrubber airflow ratio of 1.0 (measured before scrubber activation), as well as a curtain setback distance that allows the miner operator to stand at the mouth of the curtain for the entire cut. Dust levels on the bolting faces did not appear to be affected by the longer cycles associated with deep-cut mining when good ventilation practices were used.

Jan 1, 2011

By S. Corrent, F. A. V. Guimarães, M. G. Barbosa

"INTRODUCTION Moisture can be a villain, so new technologies have been explored to make more viable the production of high moisture iron ores. The current work presents the attempt of the utilization of a superabsorbent polymer (SAP) to aid in the screening process and in the ore handling process, such as stockpiles reclaiming and vessels/trains discharge in sub-zero temperature conditions. The results have shown that the polymer can be used in certain cases to improve productivity and increase safety in the process of handling the material (by increasing the TML). However, for size separation no advantages were found upon the use of the polymers. WATER ADSORPTION MECHANISMS The use of water in mineral processing is constant as its utilization brings an increase in the efficiency of separation. Although we have better results in the processing with water, materials with a high content of “natural” moisture can be very difficult to be treated by the conventional methods of separation. Nowadays many studies have been conducted in order to understand the effect of adsorption of water in the particles of complex minerals. Those studies have being divided in many different lines of research such as contact angle of a drop of water and the surface of the mineral to determine hydrophobicity, the particle size distribution and the porosity of particles. Mainly two forms of adsorption of water by the particles are possible: one the water is retained inside porosity of the particles. Laboratory tests developed in China have showed that capillary adsorption is faster in coarser particles that achieve the saturation degree earlier than finer particles (Xuewei Lv et al., 2011). The so called non-porous model considers the effect of water in the bulk sample of iron ores, in a physical connection when all the water works as a binder between particles as shown in the figure 1.If we take into account the compressibility of the system and compaction due to the weight of the bed over the particles, the thickness of the water film between particles is the same but the volume inside different particle size systems is much higher than in a system with particles of same size."

Jan 1, 2018

By J. C. Stankus

How to quantitatively identify the loads on a square/arch set is a complicated issue in designing the square/arch set in an intersection/entry. From an engineering perspective, understanding the nature and support mechanism of standing support such as a square/arch set can not only help design the support structure to maintain the roof stability, but save the steel materials and costs of manufacturing, labor, and delivery. Based on the design practices in recent years and successful applications in slope bottom intersections, the authors are confident that the concept of interaction and confinement effect between the steel square/arch set and surrounding rocks is critical in designing a proper steel structure to support an intersection/entry. This paper will detail the design concept and its applications in several underground slope bottom intersection designs, reaching the goals of improving roof stability and reducing costs.

Feb 23, 2014

By R. Brantley Sudderth

There are three broad categories in which most solvent extraction technology can be distributed?: 1) reagents, 2) equipment, and 3) systems. Reagents which are now used in commercial solvent extraction plants are of many chemical types, and each possesses certain properties which make it more economically desirable than another alternative. The equipment which is' used in solvent extraction plants for contacting the organic and aqueous phases and separating the same is varied. Most common to the industry is the mixer-settler unit which in itself, can be of varied design; but many new innovations in contacting and separating equipment have been recently introduced or are :now being studied. Each specific solvent extraction application will often dictate the type of contacting and separating equipment used. Obviously, the trend is toward smaller less expensive equipment which reduces the often expensive organic inventories necessary for most solvent extraction plants. The current thrust of .investigations in ancillary equipment is usually aimed at recovering organic from solvent extraction sludges or from aqueous streams exiting the process.6 This type of equipment helps to reduce the total organic losses from solvent extraction plants and thus reduce the operating costs. The term "systems" in solvent extraction applies to the manner in which a solvent extraction process is carried out. This manner is usually dictated by the properties of the reagent which is used, and it involves a tailoring of the equipment or the process flowsheet. Some of the things which can be tailored are: 1) The aqueous media -whether acidic or basic and what type of acid or base 2) Counter-current or single stage (co-current) contacting 3) EMF or pH control 4) Organic "crowding" alternative 5) Heating or cooling process streams Regardless of the type or extent of tailoring, efforts to do this are usually a result of the low cost of solvent extraction as a unit process.

Jan 1, 1977

By J. Diao

In order to understand the flotation kinetic behavior of coal and associated mineral matter, a detailed investigation was conducted in a 2-liter Denver flotation cell using three high sulfur coals at three feed sizes, minus 28. 100 and 200 mesh. Subsequently. the flotation products were sieved into different size fractions and analyzed for their ash and pyritic sulfur content in order to delineate the effect of particle size on the rate at which each constituent floats. The results were tested with several different flotation kinetic models and the best model for coal was then chosen. The flotation rate constant and the ultimate recovery calculated from a kinetic model were used to delineate the effect of particle size, collector (dodecane) and frother (MIBC) dosages on the flotation kinetics of coal, ash and pyrite.

Jan 1, 1992

By C. Mark, D. M. Pappas

From 1999 through 2008, groundfall events resulted in 75 fatalities, 5,941 injuries and 13,774 noninjury roof falls in U.S. underground coal mines, according to the U.S. Mine Safety and Health Administration (MSHA). A comprehensive analysis of these events was conducted to better understand where and why these incidents occurred. The first segment of the study used the MSHA database to evaluate groundfall injury rate trends related to mining method, year, locality, seam thickness, mine size, coalbeds and seasonal effects. In the past decade, roof fall injury rates have dropped 50%, but rib fall injury rates have remained constant. Room-and-pillar mines had a roof fall injury rate that was nearly 2.5 times the longwall rate. High groundfall rates occurred in the Illinois Basin, a finding that correlates with other studies that have shown that roof rock in the Illinois Basin is weaker than that in the central Appalachian coalfields. Finally, noninjury roof fall rates in the eastern and central United States were found to be 50% higher from July through September, possibly because of the changes in humidity levels that may cause shale mine roofs to deteriorate. The second segment of the study evaluated the root causes of failure by reviewing all MSHA groundfall fatality reports for 1999-2008. Pillar recovery was the leading cause of groundfall fatalities (19%), followed by rib falls, roof skin falls and traveling under unsupported roof (16% each). Defining prominent ground control incident trends and hazards will identify areas where additional study is needed and where innovative solutions need to be developed to reduce these severe occupational hazards.

Jan 1, 2011

By W. S. Weldon

The use of spiral separators for the beneficiation of fine coal typically in the size range -2+0.1mm is now well established process technology. Developments during the mid 1980's resulted in the production of cost effective, efficient large diameter coal spiral separators. Recent developments and research have been geared to optimize metallurgical performance, materials handling and equipment geometry of large diameter coal spiral separators.

Jan 1, 1997

By R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner (SPL), obtained at the end of the pots life contains a small amount of cyanide and fluoride which present environmental problems. SPL became a listed hazardous waste under RCRA (K088) in July, 1990. One of the possible uses of spent potliner is as a substitute for Calcium Fluoride (CaF2) as a fluidizer in iron-and steel making and in the glass industry. A low viscosity and a low melting point are prime requirements for accomplishing the above. In the present study, viscosity measurements were performed. Effect of various additives, such as sand, limestone, dicalcium silicate dust, and MgO baghouse dust on the viscosity of SPL was studied. The results showed that with the addition of sand and limestone, very high fluidity of SPL melt can be obtained at significantly low temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 1999

By B. E. Davis

A technique was devised by the Bureau of Nines to recover coarse (plus 1.7 m) North Carolina phosphate now discarded as waste. Concentration utilizes the difference in particle sphericity between the relatively flat calcite and the rounded phosphate pebbles. Sizing, treatment in a continuous hydraulic classification system, and grinding upgraded a 17.0-pct-P205 reject to 24.5 pct P205 with a phosphate recovery of 63 pct.

Jan 1, 1985

By R. C. Kellner

Duval Sierrita Corporation, a wholly-owned subsidiary of Duval Corporation, operates an 86,000 STPD copper-molybdenum concentrator near Tucson, Arizona. Shortly after production commenced in February, 1970, it became apparent that the reduction crushing system represented a limitation to reaching the design capacity of 72,000 STPD. The development work performed on the reduction crushers in order to first meet design capacity, and to subsequently increase production to 86,000 STPD is described in this paper. The Sierrita plant is a conventional three stage crushing sys- tem. All crushers were supplied by the Allis-Chalmers Corporation and consist of two 58 x 89 Superior gyratories, four 138b EHD hydrocones, and ten 384 hydrocones. Screening is performed prior to and subsequent to secondary crushing and in closed circuit with the tertiary crushers. Typical throughput rates and equipment sizes are presented in Figure No. 1.

Jan 1, 1975

By J. A. González-Anaya

This laboratory work presents a study of the effect of ultrafine grinding on the gold recovery of a highly refractory gold concentrate. The particle size of the concentrate was P80 = 46 µm and the main species present were quartz (28.58%), dolomite (25.63%), pyrite (20.93%), arsenopyrite (15.39%) and 112 g/t gold. After optimizing hydrated lime and lead nitrate additions, standard cyanidation with 1% NaCN, pH = 12.3, 25% S/L permits to recover only 9.4% of the gold. Different particle sizes were submitted to cyanidation. When the concentrate was ground to ultrafine sizes (P80= 4.6 µm), the gold recovery for the same cyanidation conditions increased to 67%, with cyanide consumption of 66.7 kg NaCN/t. Additional tests were performed in order to reduce the cyanide consumption. The reduction of the cyanide concentration in the leaching solution from 1 to 0.5% and the addition of 100 g Pb(NO3)2/t allowed the reduction of the cyanide consumption to 27.6 kg NaCN/t (58% reduction), while maintaining the same gold recovery of 67%. The remaining gold could be present as very fine inclusions or in solid solution in the matrix.

Jan 1, 2011