Search Documents

By T. E. Scartaccini

A drill recorder is a permanent data collecting instrument. In open pit blast hole drilling the application of a drill recorder is that of data collection, drilling control, and drilling education. The various drilling parameters (weight, RPM, penetration, torque, and air) have a drilling correlation which can be demonstrated and documented by a recorder graph. When the correlation is physically put to use during the process of drilling, then the recorder has become a drilling tool and is no longer just a data collecting instrument, per se. By being able to maintain accurate records and drilling control, comprehensive studies of changes both operational and technological can be made. These are based on in-progress facts and not after-the-fact logs. To determine total drilling efficiency, drilling conditions must be documented and controlled. Field operations at American Smelting and Refining Company's Mission Mine have proved that by increasing drilling control, demonstration of parameter relationships, and drill monitoring, more economic efficiency can be obtained. In comparing results obtained with recorder control and conventional control a decrease of 14 percent to 36 percent of drill footage costs were obtained. The percentage of variance is dependent upon whether drilling is milled-tooth or carbide-insert bit drilling.

Jan 1, 1970

By Hasan Sevim

This paper summarizes recent developments in modeling of underground coal slurry haulage networks for determination of optimum design and operating parameters. The model presented here is based on a stochastic dynamic programming formulation, applicable in any typical room-and-pillar and/or longwall mining configuration commonly practiced in the United States. The formulation and the structure of the model is general enough to handle design problems involving more than one face and mining method. Given the stochastic operating characteristics and a system layout, the model can be used to determine the equipment configuration and operating regimes that minimize the overall unit cost of coal haulage.

Jan 1, 1983

By Charles H. Rice

Coal liquefaction processes can be divided into two broad classifications - direct and indirect. Direct liquefaction processes, in general, slurry coal with a solvent and react it with hydrogen under elevated temperature and pressure. Indirect liquefaction is the term applied to processes in which coal is first gasified to generate a synthesis gas of carbon monoxide and hydrogen. The synthesis gas is then converted to various types of liquid fuels by the proper selection of catalyst and conditions. The first experiments on direct coal liquefaction were undertaken in 1933 by Bergius. Development and commercialization of the Bergius concept was accomplished mainly through the effort of I.G. Farben at the Ludwigshafen plant of its subsidiary, Badische Anilin und Soda Fabrik A.G, under the leadership of M. Pier (1). A demonstration plat having an annual capacity of 100,000 tons of coal was built in Leuna, Saxony in 1927. Six years later, Imperial Chemicals Industries, Ltd., commissioned a plant in Billingham, England (2).

Jan 1, 1981

By Richard C. Corson

The new 9300 TPD sinter plant being built for China Steel Corporation is incorporating the latest computer technology for plant control systems. The control system will use a central computer and distributed micro-processors to control instrument loops and switching logic in the blending yard and sintering plant. All plant functions, including combustion and fan controls, will be controlled by remote microprocessors located throughout the plant, and connected by a communications link to the centrally located computer and control room. The design, programming, construction and operation of a microprocessor based control system presents new challenges to the control engineer. With microprocessors in the control system, more power exists in the individual control loop and many supervisory functions may be added at the loop level. The specification of the microprocessor system and the resolution of hardware design and control system design can lead to development of powerful systems capable of higher level control and optimization functions

Jan 1, 1981

By P. A. Korpi

In March of 1978 the first set of Angular Spiral Liners utilized in grate discharge ball mills for wet grinding was put into service in the San Flanuel Concentrator of Flagma Copper Company. The use of these liners has decreased grinding media consumption by 19.2% and grinding energy consumption by 15.8%. In addition a 1.1% increase in grinding throughput is being realized through the use of the system. This paper describes the Angular Spiral Lining System and reviews the test program at the San Manuel Arizona Concentrator. Operating parameters are discussed in addition to the current testing program to futher optimize the system.

Jan 1, 1982

By R. M. Smailer

Detailed description of the development of the FIOR process1 and, subsequently, other technical papers relating to the operation and start up of the FIOR plant2,3 are available in the technical literature. The Fluidized Iron Ore Reduction (FIOR) process plant constructed in the Matanzas region of Venezuela represents the first commercial application of this technology. The FIOR process was developed by Exxon Company during the 1950's and 1960's; and the facility in Venezuela was designed and constructed by Davy McKee with the plant start up in 1976. While there is a minority government ownership in the company, FIOR de Venezuela operates as a private sector company with the majority of the ownership being private capital.

Jan 1, 1981

By Gordon B. French

The Occidental Oil Shale mining and retorting system for the production of shale oil has many advantages over the conventional underground mine and surface retort systems. For example only a portion of the oil shale is mined and transported to the outside, where it blends with the existing shale talus found on most of the slopes in the immediate area. The retorted spent shale is retained underground so that it does not become a surface disposal problem. The process consumes only minor amounts of water which is produced in adequate amounts in the retorting to fulfill all mining operations needs without outside supplies. Noise and dust levels are kept to a minimum with most of the facilities located underground. The exception being the generating stations and facilities as required to monitor air and water qualities, and last but not least, more than four times as much oil is pro¬duced from a given acre than from conventional surface processing. With the increased thicknesses as available on the government monopoly area this number could be increased by a substantial amount.

Jan 1, 1975

By Sandip K. Mukherjee

In underground mining operations, ventilation and water sprays are the common methods of controlling dust. In recent years there has been a proliferation of technical literature dealing with water sprays for dust control. However, guidelines for the design of an effective water spray system have not been presented to the mining industry. This paper reviews developments in water spray dust control technology and recommends guidelines for water spray systems to control dust in under- ground coal and non-coal mining operations. These guidelines suggest type, number, location and orientation of nozzles, desirable operating water pressure, and associated filtration system.

Jan 1, 1983

By Lee W. Saperstein

P.L. 95-87 contains explicit demands for land-use planning in its reclamation and designation sections. Both sections require recognition of local land-use plans; however, the sections are not well integrated. Accommodations to these planning requirements may be found in suggestions based on British mineral planning practice. Better links can be created among local land-use planners, the state's permitting authority and designation office, and mine designers. Mining companies should take more interest in local land-use plans and in resource inventories; states should consider devolving to local government responsibility for accepting mine permit applications and designation of unsuitability petitions.

Jan 1, 1982

By Carl E. Schubert

The application of geophysical technology relative to the exploration, planning, and operation of coal mines is expanding. This is due to the trend of the industry to increase the size of operations, use of mechanized equipment and mining of more difficult coals, where unforeseen conditions can affect mine profitability. Coal is a good geophysical target because of its lower density, higher electrical resistivity, lower seismic wave velocity, and lower magnetic susceptibility in comparison to typical country rock. The more important techniques are well logging, high resolution seismic reflection, seam wave velocity, and radar. These methods can be used to map coal horizons, determine the physical properties of the coal, and identify mining hazards. The methods are not a pancrea however. Their use should be based on a careful assessment of their expected success and cost benefit analysis in comparison with conventional technology, primarily drilling, which none of the techniques presented should entirely replace. In general, the level of technology developed for geophysics surpasses their current level of application to coal problems. In some cases, identifying hazards in advance of mining using seam wave seismic in particular, the state of the art has been developed in Europe and is awaiting fruitful application in the United States.

Jan 1, 1982

By Derek J. McCracken, William G. Holroyd

Emery is a rock that at one time held a large share of the abrasives market. The introduction of synthetic abrasives, however has forced it to settle for only certain niches in the marketplace. This loss of market share is due mainly to the higher amounts of impurities and weaker internal structure that naturally occurring minerals have compared to manmade materials. The use of rocks and minerals as abrasives dates back to early man, who used flint, quartz, and other natural materials to fabricate various tools. During the 19th century, with the Industrial Revolution imminent, the character of the abrasives industry was changed forever as synthetics were introduced. Frank B. Norton is credited with producing the first manmade abrasive when, in 1855, he manufactured a vitrified grinding wheel using emery grit and clay. Before Norton's accomplishment emery had been the only commercially available abrasive. The latter part of the 20th century has seen synthetics capture an increasing share of the abrasives market from natural materials. The term emery is believed to have been derived from the words emeri (French), smeriglio (Italian), and smiris (Greek). The term corundum, for the principal mineral of emery, seems to have originated from kauruntaka, the Indian name for the mineral. GEOLOGY Emery is a gray to black, granular rock comprised of various minerals including corundum (A1,0,), an iron-bearing mineral (usually magnetite-Fe,O,, hematite-Fe,O,, or hercynite- FeAI,O,), and several trace impurities such as mullite, titania, silica, and magnesia. The hardness of emery normally ranges between 7 and 9 on the Mohs scale, depending on its mineral com- position and level of impurities. Corundum, the hardest mineral in emery, typically has a hardness of 9. The specific gravity of emery ranges from 3.2 to 4.5, also depending on mineral composition and purity. The crystallography of each mineral contained in emery differs somewhat. Corundum exhibits an hexagonal crystal structure, whereas magnetite forms within the isometric system, frequently as octahedral crystals. Hercynite, an iron spinel, is also isometric. Hematite has an hexagonal structure but often is found as botryoidal and reniform masses. Principal deposits of commerical emery are found in the United States, Turkey, and Greece. In the United States two emery producers in the Westchester County-Peekskill area and one in the Cortlandt County area of New York closed their mines in the late 1980s. Commercial production in the United States now comes only from the western Cascade Range in Oregon. The emery in New York has a typical A1,0, content of 41.5%. Most of the rock is not true emery because it contains a mixture of spinel and magnetite but very little corundum. The deposits are of Late Ordovician-Early Silurian age and consist of veins in which emery is mixed with olivine, pyroxene, and hornblende. The veins evidently were formed by contact metamorphism and are surrounded by Precambrian schists that contain mica, sillimanite, cordierite, garnet, and quartz. The deposits in Oregon were formed during Miocene time by the contact metamorphism of ferrunginous bauxite by intrusive lamprophyric dikes and plugs. Emery is found in thin layers bordering these tabular dikes, which are usually oriented perpendicular to bedding, and in "surficial placer deposits. The emery deposits in Turkey occur as small, massive, lens- shaped bodies and as surficial placers. They are believed to have formed during Permian and Triassic times. In Greece the principal site of emery production is at Cape Emeri on the Island of Naxos. These deposits consist of lenticular masses of emery surrounded by marble. They originated during Mesozoic time, evidently by metasomatic replacement. Smaller deposits on several other Aegean islands were formed by the metamorphism of bauxite or other alumina-rich materials.

Jan 1, 1994

I found the article most interesting and timely. I consider it imperative that mine case studies like this one are undertaken and published so that the practicing mining engineer and geologist can obtain a better idea of what is the preferred estimation and grade control technique to use, given the site-specific geology, grade distribution, etc. Mining companies, with operating gold mines, need to be encouraged to either initiate such a study in-house or support a research project by financing a graduate student at a local university. The latter method is preferable since it not only provides research support but also an excellent training opportunity for young mining engineers and geologists. Ideally, what is needed is exploration drill-hole, blasthole, and mine production data that can then be used to assess the efficiency of different estimation and grade control methods by comparing the results obtained using the drill/blasthole data with the actual production data. It is hoped that more mining companies will realize that the rewards from this kind of research greatly outweigh the sometimes perceived problem with releasing data to a university. I noticed that the authors used the blasthole data to represent the actual values, the validity of which relies heavily on the two key assumptions with regards to blasthole assays and in-pit ore-waste selection procedures. Could the authors comment in more detail on these assumptions and what criteria they used to check the validity of the assumptions? Since the article was published, have the authors had the opportunity to compare their estimates with the actual production data? It would be interesting to compare other estimation methods with OK and IK. For example, how well did the polygonal method used at the mine compare with the results given in the paper? I would like to mention that B.L. Kwa completed a similar study (Kwa and Mousset-Jones, 1986) using exploration drill-hole, blasthole, and production data from the Alligator Ridge mine in Nevada. The study compared a variety of estimation methods, including IK, and the final results are shown in Fig. 1. The IK method exhibits the smallest difference between estimated and production results and is closely followed by the indicator moving window (Ind MW) method. Reply by Y.C. Kim We do concur with Professor Mousset-Jones with respect to the merit of such case studies performed at a local university. In answer to his request for comment on the validity of the two key assumptions made in our paper, we can only say that these are reasonable assumptions that are very difficult to validate. The assumption of blasthole assays being accurate can be partially validated by a careful analysis of the nugget component of blasthole variograms. The assumption that the in-pit ore-waste selection procedure in use was an effective one can only be validated through comparison between the mine estimates of ounces of gold versus the actual recovered ounces of gold at the mill. Neither one of these two assumptions has been validated to date due to several reasons. For example, the mine went through a change in management since the study. Similarly, no compelling reasons have been presented to perform detailed variogram analysis of the blasthole data. We do, however, believe that the obtained results (i.e., indicator kriging performs better than OK in a highly skewed deposit) will remain the same in relative terms, regardless of how valid these two assumptions may be. The most recent com¬parative study by D. S. Lindsey of the Montana College of Mineral Science and Technology also shows a similar ranking between ordinary kriging versus probability kriging, which is an extended version of indicator kriging.

Jan 1, 1987

By J. D. Patsey, G. T. Lineberry

Introduction A computer program was developed for analyzing drum-type hoists before modifying an existing system or designing a new one. Its use permits the preliminary evaluation of a system before seeking technical assistance from mine hoist designers and manufacturers. The user-friendly program accepts a variety of data and analyzes hoisting systems for any balance state. The program can be used to calculate skip capacity to yield a desired production rate, solve for drum face width, select a permissible wire rope, estimate total horsepower of the hoist plant, and estimate annual power cost. Whether required for a large mining complex or for a relatively small operation, a hoisting system must be carefully designed to ensure the efficient, reliable, and safe flow of material. Because shaft sinking and hoist installation can total between 2.5% and 3% of the cost of opening a deep mine, proper hoist selection is critical. Today's mining engineer has at his disposal the most powerful design and analytical aid ever, the micro- computer. There is, unfortunately, limited software for the study of hoisting systems, unlike that for other materials handling equipment (Manula and Albert, 1980; Prelaz et al., 1964; Bucklen, 1969; Thompson, 1985). HOIST reduces a time-consuming set of calculations to a concise package of interrelated subprograms. A literature review revealed no common-user pro- grams to analyze hoisting systems, although at least four major hoist designers/manufacturers/installers have their own in-house programs. To provide a tool with which the mining engineer could preliminarily analyze a materials hoisting system or could check the calculations of a hoist contractor, a computer program was developed. HOIST was written in BASIC for the IBM-PC for ease of program adaptation and to en- courage field use on compatible systems. Details of program development are omitted, since the basic principles of hoisting analyses are relatively straightforward, simple, and readily accepted (Har- mon, 1973; Nordberg, n.d.; Adler, 1957). Program features, intended usage, and benefits of the com- puterized solution are emphasized over theory development and mathematical rigor. Background The mine hoist system that is selected and installed at a mine is the "lifeline" of that mine, with installations lasting 20 years or more. Thorough study is warranted to ensure that productivity demands are met at a minimum cost per ton. The increased cost of a large, powerful, high-speed hoist must be offset by increased production to justify its selection. To optimize this tradeoff, an extensive hoisting analysis should be performed. The analyses to properly size the skip (or cage ) , the drum, and the hoist drive are conducive to computerization, permitting rapid evaluation of changeable operating and design parameters, such as velocity, acceleration, state of balance, and productivity demand. The program is particularly useful in conducting sensitivity trials, such as investigation into the effect of change of productivity on skip capacity and on horsepower of the hoist drive. HOIST is currently limited to the study of drum-type hoists with cylindrical drum(s). However, only minor changes to the program would permit analysis of friction hoists and conical drum configurations. Model development and testing The program is based on accepted equations and physical relationships. Examples of manual calculations formed the basis for decision points and program branching. Data is input in the order that it would be needed if the problems were solved manually. The choices are arranged likewise. HOIST was developed in sections, with manual solutions performed to check program logic. The testing became more rigorous as sections were completed. Output from one section becomes input for following sections, as appropriate. The simplified flow diagram of HOIST is given in Fig. 1.

Jan 1, 1988

By M. M. Botz, F. W. DeVries

Discussion by F.W. DeVries Comments on natural cyanide attenuation. The paper by Botz and Mudder in the November 2000 issue of Minerals and Metallurgical Processing had one disappointing aspect. Table 1 (p. 229) failed to include a significant species - neutral copper cyanide (CuCN). This compound has been most trouble-some in many plant-scale cyanide cleanup processes, includ- ing acidification-volatilization- reneutralization (AVR), hy- drogen peroxide cleanup and air/SO2 cleanup. It has also plagued many pilot efforts to use ion-exchange (IX) resin technology. This author elucidated the concept that, under some conditions, copper cyanide failed to precipitate out of treated effluents and appeared to exist as a filterable colloid that reported as copper and cyanide, with the latter measured as WAD (weak-acid-dissociable) cyanide in that analytical method. The concentrations measured were very near the levels of 0.2 ppm, often the regulatory limit for WAD cyanide. The copper concentration, using the 1 : 1 ratio for this com- pound, would then be more than 0.4 ppm, which could also be unacceptable. We discovered that it was unsafe to assume that the Cu(CN),- would surrender both cyanide ions simultaneously and allow cupric copper to be removed subsequently as, say, cupric ferrocyanide (Hatchett's Brown). This compound could be ignored as safely as the "iron blues," as essentially an inert solid, stable in geologic time if not exposed to sunlight. Under poorly controlled oxidation of the cyanocuprite ions (copper with four, three or two cyanides complexed to the copper), CuCN could well be formed and could not be assumed to precipitate out as a solid. The authors of the paper, by failing to include the CuCN species in their model, may have left users of the model prone to ignore the possible occurrence of the colloidal(?) form in the discharge, thus finding an effluent that failed to meet regulatory limits. (See addendum below.) This somewhat ephemeral material may well have been responsible for some large-scale failures of cyanide destruction technology to succeed at sites in North America and elsewhere. Two specific references alluding to this occurrence may be found: Griffiths et al., 1987, "The detoxification of gold-mill tailings with hydrogen peroxide," Journal of the South African Institute of Mining and Metallurgy, September, p. 282. DeVries, 1989, "Improved understanding in detoxification of cyanide leach liquors using peroxide" Rand01 Gold Conference, Sacramento CA, p. 15 1. It is advisable for workers in this area of cyanide removal or recycle to avoid assuming that CuCN will, with certainty, precipitate out of solution, or that the dicyanocuprite ion will part simultaneously with both cyanide ions and allow cupric copper to be dealt with by other reactions. One further piece of work may be incomplete. That is, a definitive study of the long-term behavior of CuCN that does precipitate when exposed to other compounds present in neutralized tailings. Addendum. The extremely complex reaction of cupric ion on cyanide- which, of course, results in oxidation of cyanide to cyanate, probably through the intermediate stage of forming cyanogen [(CN)2] from oxidation of HCN with its hydrolysis to cyanate and cyanide ion - involves two cyanide moieties and the reduction of the cupric ion back again to the cuprous state. This, then, can form the CuCN potential "solid" that was already the undesirable species. In cyanide cleanup, with either air/SO2 or hydrogen peroxide, copper is generally employed as the catalyst, so it is unclear what happens when the CU(CN)2-1 is ultimately exhausted. Certainly, the field evidence is quite clear that all

Jan 1, 2002

By August V. Castelli

Drilling fluids have changed over the years from water and/or water frequently mixed with local clays to scientifically com- pounded materials (mud). This change has occurred due to changes in drilling methods from percussion to rotary: depth maximum from 21 m in the first oil well to more than 9 000 m; and variety in types of well or hole to gas, oil, water, and mineral exploration. Environmental concerns about the composition of the fluid as to heavy metals and oil on the cuttings has recently caused changes in the materials used in the mud. The drilling fluid should perform the following functions (Darley et al., 1980): 1) Carry cuttings from beneath the bit, transport them up the annulus, and permit their separation at the surface. 2) Cool and clean the bit. 3) Reduce friction between the drilling string and the sides of the hole. 4) Maintain the stability of uncased sections of the borehole. 5) Prevent the inflow of fluids-oil, gas, or water-from permeable rocks penetrated. 6) Form a thin, low-permeability filter cake which seals pores and other openings in formations penetrated by the bit. In addition to these, the fluid should: 1) Not injure drilling personnel nor be damaging or offensive to the environment. 2) Not require unusual or expensive methods of completion of the drilled hole. 3) Not interfere with the normal productivity of the fluid- bearing formation. 4) Not corrode or cause excessive wear of drilling equipment. A number of industrial minerals, chemicals, and other materials are used as additives in the drilling fluid to accomplish these functions. Industrial minerals make up the highest percentage of the additives in a drilling fluid. Drilling fluids are classified according to their principal components: water, oil, and gas. If the major component is either water or oil, the component along with the suspension of solids, cuttings and additives is referred to in the trade as a mud. The largest use of some industrial minerals, such as barite and bentonite, is in drilling muds. For other materials, such as gypsum and limestone, drilling usage is only a small percentage of total demand. RAW MATERIALS [Table 1] lists the industrial minerals used in drilling fluids, their form, specifications, and uses. Each raw material will be discussed as to its mineralogy, physical and chemical properties, and the location of major deposits with respect to drilling fluids. Attapulgite Attapulgite is a crystalline hydrated magnesium silicate clay mineral, prized for its viscosity in saline waters. The particles are needle-like rather than the platelets common to most clay minerals. The specific gravity is 2.5 and the Mohs hardness is 1 to 1.5. Attapulgite is one of the materials sometimes referred to as fuller's earth. The major producing areas in the United States are southern Georgia and northwestern Florida. It also is mined in Spain, Senegal, the Republic of South Africa, Turkey, India, and Australia. Barite Barite is crystalline barium sulfate. It has a high specific gravity for a non-metallic mineral, 4.5 when pure, and is used as a weighting agent. Generally, the specific gravity ranges from 4.20 to 4.35. It is relatively soft with a Mohs hardness of 3 to 3.5 and is not very abrasive. Barite is inert, non-toxic, and clean to handle. Common contaminants are quartz, iron minerals, gypsum, and calcium carbonate. If there is considerable gypsum in the barite, it will thicken the mud. The major deposits in the United States are in north central Nevada, near Battle Mountain. The major producing countries, other than the United States, are China, India, Mexico, the former USSR, Turkey, and Morocco. The major deposits in India and Nevada, and some in China, are stratiform, commonly quite pure bodies in bedded sedimentary rocks.

Jan 1, 1994

By H. Boyd

Fluid energy grinding, or jet pulverization, refers to the process of entraining solid particles in high velocity gaseous or vaporous streams and reducing their size by impact and attrition against other particles or some sort of target. Since all desired size reduction is not achieved in one pass through the zone where energy is applied, some form of classification is necessary to return oversize particles to the grinding zone for further size reduction. Applications Fluid energy mills have normally been used to produce products where the particle size is basically finer than 325 mesh. Products having particle size distributions with a maximum size of 4 or 5 µm, and with a high percentage finer than I µm, can be produced using fluid energy mills. More recently, some fluid energy grinding units have been applied economically to produce ground products with 1 or 2% coarser than 200 mesh. It is also possible to consider usage of a jet-pulverizing zone, without the usual integrated air classi¬fier, operated either in open circuit or in conjunction with a screen. Feed sizes to be delivered to the fluid energy mill depend on the material involved, the type of jet pulverizer used, the finished product size requirement, and the upstream process. In some units feed sizes up to l in. or larger can be accepted, but practical economics usually require the starting material to be -4 mesh or smaller and some pulverizers are typically fed at 20 mesh top size. It is not unusual to find feed materials at essentially -325 mesh when extremely fine products are needed, since capacities are improved with finer feeds. Conventionally the fluid energy grinding process has been used for relatively soft and nonabrasive materials. This includes very low¬melting-point and temperature-sensitive materials or coatings, since there is no measurable temperature rise during fluid energy milling. More recently, however, jet pulverizers are being used on highly abra¬sive materials such as silica, feldspar, glass, zircon, calcined alumina, coke, boron carbide, and similar materials. Since the primary energy application is by impact of particles against themselves, there is a low rate of wear resulting in a small amount of product contamination and in low maintenance costs. Usually the fluid energy pulverizer produces a more narrow particle size distribution than other mills provide, and this is useful where such a requirement exists. It is possible, within limits, to adjust classifi¬cation and other functions of the overall fluid energy system to vary the particle size distribution curve and thereby approach the broader distribution obtained from other grinding methods. By controlling the temperature, composition, and humidity of the fluid used, it is possible to incorporate other functions with the size-reduction process. These include drying or adding moisture, coating, mixing and blend¬ing, and even oxidation or reduction and other chemical reactions or their inhibition. The finished product is discharged in the fluid stream and is conveyed pneumatically to the desired point, where a suitable dust collector must be provided. Operation and Mechanical Features One of the earliest fluid energy mills is the Micronizer now manu¬factured by the Sturtevant Mill Co. Similar units are also manufac¬tured by Jet Pulverizer Co. and others. As shown in Fig. 81, the micronizer consists of a shallow circular grinding chamber with noz¬zles arranged at the outer periphery to discharge tangentially inward. Fluid (usually compressed air or superheated steam) is provided to the nozzles from a manifold at pressures normally in the range of 100-150 psig and at temperatures up to 800°F or higher, depending on the raw material, required results, and economic factors. The com¬pressible fluid expands to high velocity through the nozzles and gener¬ates a spiral flow pattern in the grinding chamber, and discharges

Jan 1, 1985

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

The literature on four different topics is re¬viewed herein for purposes of mathematical mod¬eling of mine water inflow. The first of the topics reviewed is modeling of fissured or fractured ma¬terials; the second is general Darcy based flow models; the third is field methods for determining fracture flow properties; and the fourth is methods used presently for determining mine water inflows. The four topics are considered in the foregoing order. FRACTURE FLOW MODEL Two basic types of fracture flow models have been developed. The first type uses various tech¬niques for space averaging to obtain the equations. Systems are considered in which the porous media properties vary smoothly enough and the fracturing is sufficiently profuse and well distributed that the locally averaged properties are meaningful when viewed on the macroscopic scale. The final result is that a coefficient is used which is similar to saturated hydraulic conductivity and in many cases, simply is hydraulic conductivity. In other cases, the coefficient is apparent hydraulic conductivity be¬cause the response from flow in the fractures is more rapid than flow in the pore spaces. Faust and Mercer (1980) refers to this method as the contin¬uum approach. Some of the papers on this type of problem are by Duguid (1973), Verner et al. (1974), Owili-Eger (1975), Duguid and Abel (1974), duPrey and Weill (1974), and O'Neill (1978). Duguid and Lee (1977) also considered heat flow in the fluid and the porous medium. These papers all result in various types of computer programs. Some papers on this topic that do not result in computer programs are by Snow (1968, 1969) and Streltsova (1976). Some of the foregoing articles consider con¬solidation of the porous media and the resulting effect on hydraulic conductivity. Barenblatt et al. (1960) developed an analytical solution for fracture flow and discussed the time that is involved in the drainage process and the effect that fracture flow has on the drainage time. The second type of fracture flow model con¬siders the width of the fractures as a function of the pressure in the field. Faust and Mercer (1980) refers to this method as the discontinuum approach. This approach often requires two finite element programs that consider the stress in the material and the flow in the fractures separately. The pro¬grams are then linked to arrive at the final solution. Some of the articles that consider the interrela¬tionship between pressure and the size of the frac¬ture but do not use computer solutions are Gringarten et al. (1975), Narasimhan and Palen (1979), and Witherspoon et al. (1979). Papers that use a linked computer program between stress and flow are by Ayatollahi (1978), Gale et al. (1974), and Noorishad et al. (1971). Ayatollahi's program is primarily for the petroleum industry because it does not consider the effect of gravity. Ayatollahi assumes that pressure effects are very large in com¬parison to gravity effects. This assumption would apply only to very deep aquifers. Articles that consider fracture flow on a more applied basis are by Wittke et al. (1972), who con¬siders that the flow is entirely through fissures and negligible through the pores of the rock. Gringarten and Witherspoon (1972) developed type curves that may be used for analysis of fracture flow systems; the curves are based on the assumption that it is possible to distinguish between aquifers with hor¬izontal and vertical fractures and that it is possible to analyze the system as an equivalent anisotropic homogeneous porous medium with a single fracture with much higher permeability. DARCY FLOW MODELS The Darcy flow models of greatest interest to mine water inflow prediction are those which allow

Jan 1, 1986

By Robert A. Irvine

Traditionally, cost effective gains in the capacity of material handling systems were a result of increases in equipment size. In general, the use of maximum capacity components in a system optimizes the production "costs per ton." The trend-"Bigger is Better" will continue in material handling equipment. Since it is rare for plant operators to lament an over abundance of screening capacity, one can safely predict that vibrating screens will follow this trend. Large Vibrating Screens - The Challenge Large vibrating screens represent a unique challenge for Manufacturers, Plant Designers, and Plant Operators. The inherent mode of operation for vibrating screens is self-destructive. More often than Manufacturers admit, Designers plan for, or Operators staff for, a vibrating screen succeeds and self-destructs. This is a problem. It can magnify with larger vibrating screens.

Jan 1, 1983

By Christopher D. Henry

Environmental geologic maps of the Wilcox and Jackson-Yegua lignite belts of the Texas Coastal Plain delineate land areas on the basis of their natural characteristics. Criteria used to define map units include substrate, soil, topography, geologic process, vegetation, and land use. The maps are useful in planning and reclamation of lignite mines and in meeting the requirements of State and Federal surface mining laws. Specific applications include identification of land capability, recharge areas and geometry of aquifers, flood-prone areas, areas that may qualify for prime farmland status, and other areas sensitive to lignite mining.

Jan 1, 1982

By Walter E. Heinrichs

Early history of the district is typical of many, particularly in Southwestern United States. The usual early Spanish influence was felt; Marcos de Niza, Coronado and Father Kino are most notable, but authentic records regarding Spanish mining activities are sparse. About 1769 the Indian village of Tucson became a Spanish settlement. During the next century prospecting attempts were largely interrupted by the Indian, Mexican and Civil Wars. By 1870 Tucson had a population of 3200 and by 1880 the Southern Pacific Railroad extended all the way from Los Angeles. Pyrometasomatic copper ore was first produced with some local direct ore smelting done during the late 1800s. By 1907, a rail line was built from the Twin Buttes mines to Tucson by the Twin Buttes Mining and Smelting Company. World War I was a very active period, with mixed copper, lead, zinc, gold and silver production. This came mainly from underground replacement and contact metamorphic deposits and from practically all portions of the district. Some of these operations continued intermittently until the 1929 depression.

Jan 1, 1976