Search Documents

By Art Hamid, Manfred Wong, R. John Caulfield

"The proposed Channel Tunnel is a critical component of the San Francisco Public Utilities Commission’s (SFPUC) Central Bayside System Improvements Project (CBSIP), which is a key element of a $6.9-billion sewer system improvement program to upgrade its aging and seismically vulnerable wastewater facilities. The tunnel will provide gravity conveyance and storage of combined sewage flows from the northeast sector of San Francisco, CA to the Southeast Water Pollution Control Plant for treatment. The tunnel will be approximately 2.7 km (1.7 miles) long and 7.3 m (24 ft) in internal diameter. It will utilize a single-pass precast concrete segmental lining system. Tunneling challenges include excavating with pressurized face tunnel boring machine (TBM) technology through highly variable ground conditions including the Franciscan Complex (rock and mélange), clayey/silty sands, stiff to hard clay (Old Bay Clay) and mixed-face conditions. The project will also require several deep shafts that will be technically challenging. Project backgroundThe SFPUC is a department of the City and County of San Francisco, CA that provides municipal power, drinking water and wastewater services to San Francisco.San Francisco’s combined sewer system collects both wastewater and stormwater in the same sewers, which is then pumped, treated to stringent state standards and discharged into the San Francisco Bay and Pacific Ocean. The sewer system includes tunnels, large storage/transport boxes, 1,600 km (1,000 miles) of collection sewers, 28 pump stations and three wastewater treatment plants. After decades of service, much of the system is nearing the end of its useful life.The existing system is also vulnerable to seismic damage. During the 1989 Loma Prieta earthquake, damage to SFPUC wastewater infrastructure was extensive. This included the 3,415 m (11,200-ft) long, 1.7m (66-in.) diameter Channel Force Main, built in 1976, and a critical component of the conveyance system. The Channel Force Main carries 70 percent of the bayside dry weather sewage flow from the northern and central part of the city to the Southeast Water Pollution Control Plant for treatment. It is antiquated, not pile-supported and not constructed to current seismic codes. There is also currently no conveyance redundancy for north/central bayside flows to the treatment plant. Figure 1 shows the SFPUC’s wastewater collection system, the existing Channel Force Main and the project location."

Jan 5, 2017

By P. C. Dagneau

QUEBEC CARTIER MINING COMPANY was incorporated in 1957 to explore and develop low grade iron are deposits in Northeastern Quebec. Four separate deposits were located and identified as being of ore quality and size to support commercial development. Said deposits were located at Lac Jeannine, Mount-Wright, Fire Lake and Mount-Reed. In 1970, in preparation for the replacement of the depleting Lac Jeannine are reserves, construction of an SS-mile railway extension was initiated, towards the newly selected mine site at Mount-Wright. This orebody was selected because the physical and chemical characteristics of the ore were very much similar to those of Lac Jeannine, as well as its huge reserves, estimated at more than one billion tons. In addition to the railroad extension, a mine, concentrator and related facilities were constructed and the new town of Fermont was created. Total investment for the Mount-Wright project exceeded $700 million and initial production commenced in 1976. Quebec Cartier is presently (1992) the leading producer and seller of iron ore in North America at 15,5 million tons and employs some 2,300 people.

Jan 1, 1993

By D. A. Bird

Geochemical models using published thermo-dynamic data and laboratory derived kinetic rate laws allow prediction of post-closure pit lake geochemistry at open pit mining sites. A combination of "forward" and "inverse" modeling techniques can predict the pit lake geochemical evolution from initial infilling to eventual steady state attained decades or centuries after closure. Computer codes have been developed to model chemical reactions such as pyrite dissolution, describe the ground-water flow regime, and provide rock-water ratios. The incorporation of site specific information, such as ultimate pit dimensions, geologic and hydrologic data, acid generating potential (AGP) vs. acid neutralizing potential (ANP), and laboratory derived kinetic rates, allows application of the model to open pit mines at any stage of development.

Jan 1, 1994

By C. Basilio

Thermodynamic calculations based on a rigorous mass balance technique have been carried out for the chalcocite-potassium ethyl xanthate (KEX) system. The results of the calculations are used to: i) construct Eh-pH diagrams for KEX additions ranging from 0 to 10-4 M, ii) determine the amounts of cupric ions and copper xanthate formed at different Eh and pH values to make three-dimensional diagrams, and iii) determine the minimum KEX addition required to form CuX and CuX2.. This allows prediction of the optimum conditions for flotation and comparison of this with microflotation test data. In addition, voltammetry experiments have been conducted on chalcocite electrodes at pH 9.2 and pH 6.8 in order to gain information on the role of metastable species in flotation. On the basis of these experiments, possible reaction mechanisms are discussed and comparisons are made with what is expected on the basis of thermodynamics.

Jan 1, 1985

By W. Szymanski

The United States contains one of the world's largest reserves of uranium. Domestic production and exploration activities, however, have declined since the early 1980s due to weaker-than-expected growth in nuclear power demand and to foreign competition. The main result has been that more costly and less productive conventional mines and mills have closed. Meanwhile, industry productivity as measured by uranium output per employee has increased threefold since 1980. At the end of 1992, only six plants, all nonconventional, were operating in the United States. Due to cost considerations and increased environmental awareness, any additions to existing capacity are expected to be met through nonconventional in situ leach plants.

Jan 1, 1994

By G. V. R. Landman

In order to obtain a better understanding of the explosion risk at the coal face, anomalies in the ignition sensitivity for different modes of ignition of hybrid mixtures of dust, methane and air were studied. Results indicated that the explosible behaviour of the working environment is highly dependent upon the ignition source and the fuel composition. For example, depending on the ignition source, the same hybrid mixture can be inert or extremely explosible. In conclusion, it is stressed how the explosion risk can be expressed in terms of a safety factor which takes into account the influence of both the fuel and the ignition source.

Jan 1, 1994

By Enrique Llewellyn

North River Energy Company a previous subsidiary of Republic Steel Corporation commenced development of the Number One Mine in mid-1972. The mine is located in West Alabama and presently employs a total of 632 people. Production capabilities have increased to 1.4 million clean tons of steam coal per year with the newly purchased Longwall System. Washer recovery averages 57 percent. The seam being mined is the Pratt or Corona with an average height of 52 inches and an average cover of 540 feet. The immediate roof is laminated sandstone and the floor is composed of a hard fireclay. Total production out of the mine is provided to Alabama Power Company under a longtime contract.

Jan 1, 1981

By R. Kalra

The current paper looks at evaluating the merits of large geared mills versus gearless driven mills by evaluating the following factors: The capability of currently available systems in terms of power and mill diameter Efficiency in terms of overall electrical power consumed vs mechanical output power Capital cost Running costs Cooling requirements in terms of air versus water cooling Installation and delivery time World?s largest geared drive ? 2x8500kW ? Wushan, China (operating) Among the many reasons that geared drives on large SAG mills are not favoured, is due to not having an efficient variable speed drive option (60 to 80% critical speed), which is required for process reasons. As technological advances have occurred quite rapidly in recent years, this paper uses the latest data in applying these comparisons and attempts to dispel some of the myths regarding Slip Energy Recovery (SER) and variable frequency drive technology on twin pinion drive systems. Early attempts to provide load sharing on twin pinion drives used primitive electronics which have since been developed to eliminate the problems encountered in earlier attempts. In particular, torque pulsations between the twin motors have been overcome using a higher number of devices (pulses) and better electronics. With successful operation of 2 x 6.5MW (Phu Kham, Laos) and three 2 x 7MW units under manufacture (Pascu Lama) and a further 40 projects worldwide, energy efficient Hyper Synchronous SER drives are now mature and ready for use on 2 X 10MW dual drive mills. Speed variation required is in the range of +/- 15% of synchronous motor speeds. VVVF drive packages from ABB and Siemens are also available for 2 x 10MW in low and high speed options. Dual hydraulic inching drives provide a much safer and convenient operation with the added advantage of locked charge detection.

Feb 27, 2013

By Richard L. Sanford

This paper summarizes the results of the development of a Directory of Computer Programs Applicable to U.S. Mining Practices and Problems. The Directory is funded by the U.S. Bureau of Mines and includes a sampling of computer usage in operating and manufacturing companies, consulting firms, computer companies, research organizations, universities, and various U.S. government agencies. General references to computer applications throughout the mining industry are discussed as well as the availability of programs to interested organizations or individuals.

Jan 1, 1978

By S. Amirshenava, S. Nadimi

"Premature and unplanned mine closure can result in significant adverse impacts on the environment and community and need to be managed appropriately. Risk management techniques can reduce the negative impacts and risks of early mine closure. Risk Assessment 3D Model, is an efficient tool to quantify risk. The aim of this paper is to identify the mine closure risks in Choghart iron ore mine, and calculate the overall mine closure risk level. The result shows that 51.4% of assessed risks have low risk level and the overall risk level of early mine closure is low. Keywords: mine closure, risk assessment 3D model, Choghart iron ore mine INTRODUCTION The modern mining life-cycle can be divided into three main stages; exploration, mining (opening and production) and post mining (mine closure, and reclamation). Mine closure is the critical component of the modern mining life-cycle and it refers to the period of time when the operational stage of a mine has permanently ceases (Heikkinen et al, 2008). Planned closure occurs due to the depletion of ore reserves, but sometimes it is premature. Laurance (2006) shows that only 25% of mine closure in the past 30 years was due to resource depletion and in 75% of the cases the mines were closed for the other reasons. Ghanbari et al (2010) demonstrated that 48.6 % of copper mine closure in the past 100 years was due to resource depletion and 51.4 % of copper mines have been closed due to other reasons. The main reasons of premature mine closure are as follow (Laurance, 2006; Ghanbari et al, 2010; Maiti, 2013): • Economic, (low commodity prices or high costs) • Geological, (over-estimation of grade and tonnage) • Geotechnical (adverse geotechnical conditions) • Technical (equipment failure) • Regulatory, due to safety or environmental breaches • Social or community pressures • Closure of downstream industry or markets • Flooding or inrush Minaei Mobtaker and Osanloo (2013) developed a mine closure prediction model based on the data collected from closed iron ore mines in the past 100 years. They showed that economic factors, exhaustion of ore reserve and geological conditions are the main reasons of iron ore mine closure. They treated mine closure as a decision making problem in order to predict the causes of mine closure, including the uncertainties of some mine plan parameter such as iron ore price, production and consumption."

Jan 1, 2016

By Gerd L. Klinkenborg

Throughout the history of the development of mechanical conveyor systems, it has always been an established condition that loads are received at one end of a single-belt conveyor and discharged at the other end, in a point-to-point, manner. In systems designed for the continuous transport of granular materials, vertical or horizontal changes in; direction have always necessitated two or mope single-belt conveyor units, with a corresponding number of motors, assemblies and attendant mechanical and human or electronic controls. Besides these high-cost factors, every change in the system's direction also calls for a transfer point that involves a drop-back of the material from one level to another with some loss of the material and, in many cases, unwanted additional granulation. Where changes in the location of the discharge point are wanted, the conventional single-belt conveyor must either be replaced by a shorter or longer unit or additional units purchased and installed, or existing units rearranged. This can take days or weeks, and involve special expenditures as well as loss of valuable production time.

Jan 1, 1962

By K. R. Griffin

New and developing communication systems enable underground miners to not only connect to the surface from an increased communication coverage area but also to be discovered in the event of an emergency. Communication and tracking systems are required by MSHA regulations, aiming to enhance health and safety and routine production in underground operations. Modeling a mine?s potential communication coverage area will increase overall coverage and efficiency of the communication network itself. Modeling the propagation of wireless communications enables ideal broadcast locations to be found when designing a communications network. Strategic placement of broadcast devices results in a reliable communication network that can better withstand disruption in both daily operation and emergencies. This paper will discuss recent regulatory developments in underground coal communication systems, the implementation of these new technologies, and how communication system?s networks can be modeled and analyzed using computer simulations.

Jan 1, 2010

By O. M. S. Rodrigues

The kaolinite presence in bauxite ores increases caustic soda consumption during the digestion step in the Bayer process. Depending on the kaolinite content, the utilization of the ore in the Bayer process may be unfeasible. This investigation addressed the variables involved in kaolinite flotation through microflotation experiments in a Hallimond tube and zeta potential determinations. The tests were performed with a pure sample of kaolinite (96%). Five collectors were tested: Duomeen T (DT), cetyl pyridinium chloride (CPC), cetyltrimethylammonium bromide (CTAB), dodecylamine (DDA) and Flotigam EDA (EDA). Four of them performed well as collectors, at a concentration of 1x10-4 mol/L: CPC, CTAB, DDA and EDA. The kaolinite isoelectric point (IEP) was determined at pH = 4.6. The IEP was shifted towards higher pH values in the collectors? presence, indicating specific adsorption onto the mineral surface.

Jan 1, 2011

By Arnold P. Szaj

There is no startling revelation to the fact that the mining industry as a whole is generally moving toward the use of larger equipment to process ores in quantities far greater than what was even considered a decade ago. Trucks and shovels have led the way in extra large machines and many other manufacturers have followed suit in the development of so-called "supers" in their line of equipment. In order to keep pace with the industry, crusher manufacturers have also enlarged the size of their equipment. There is now on the market, a Gyratory crusher capable of accepting a 72" diameter piece of ore. Primary jaw crushers have also increased in size. It is inevitable, therefore, that larger secondary cone crushers would also be required to complement the other equipment used to process these large quantities of ore. This super-size secondary cone crusher is the SYMONS 10 Ft. Cone Crusher. Until 1973, the largest cone crusher built was the 7 Ft. Extra Heavy Duty crusher, which is currently used in the majority of the mining operations throughout the world. The 10 Ft. crusher, when compared to the 7 Ft. Extra Heavy Duty Crusher, is approximately 1-1/2 times larger in physical dimensions; three times heavier; will accept a maximum feed size which is approximately twice as large; and will crush at approximately 2-1/4 times the rate of the 7 Ft. machine at identical closed side settings. It will be the largest cone crusher built in the world. At the present time, Rexnord's Nordberg Machinery Group has accepted an order for two 10 Ft. Standard cone crushers to be delivered to an iron ore mine in South Africa in early 1975.

Jan 1, 1973

By Ayman A. El‑Midany, Hassan E. El‑Shall, Kerri‑Ann A. Hue

Modification of clays is necessary for the zearalenone (ZEN), as long-chain mycotoxins, removal. The organic-cations were usually used to modify the clay hydrophobicity to accommodate the large mycotoxin molecules. In this study, tri capryl methylammonium (TCMA) chloride and common corn oil were used in clay modification. Several characterization techniques such as XRD, FTIR, and TGA were used to identify the d-spacing changes after modification either by TCMA or corn oil. The results of applying the TCMA-corn oil-modified clays in ZEN removal indicated a noticeable improvement where more than 90% of ZEN could be removed in vitro at acidic and neutral pH values. The success of eliminating a high percentage of ZEN molecules is due to the expansion of intergallery spacing as a result of TCMA surfactant intercalation within the clayforming layers. The removal percentage does not depend only on pH but also on the amount of clay used. In addition, the ZEN removal in the presence of corn oil is better at acidic pH and small clay amount where the ZEN can be fully removed.

Sep 27, 2021

By Daniel Saramak, Agnieszka Saramak

A big issue in crushing and grinding operations in raw materials handling is high energy consumption and low breakage effectiveness. According to the Legendre [7], only 10% of energy input is directly consumed on the feed material breakage, while the remaining portion is dissipated in the form of heat and noise [8]. In the industry of limestone powder production, the grinding operations constitute integral part of technological circuits, and the energy consumption in operations of industrial comminution consume as high as 2% of world energy [14]. High-pressure grinding is the technology with proved energy benefits both in ore processing circuits and in limestone grinding. The promising results concerned mostly the achieved energy savings and good results of material breakage were achieved and demonstrated in numerous investigations [1,3,12]. However, it appears that a proper selection of operational parameters of the press devise, determination the feed material characteristics and adjustment of process course san be of a key-significance in improving an effectiveness the HPGR operation. Operational parameters of devices and process course should be verified towards the characteristics of the feed material, which mainly applies to the particle size and shape of the feed material and its moisture, and also mineralization in case of ores [2,4,9]. There are various investigations concerning an impact of the operational pressing force on comminution results which mostly refer to the determination of energy consumption and crushing ratio [5,6,10,13]. Investigations on the moisture content are less common, however their results suggest that, in general, the HPGR feed with higher moisture shows the tendency to higher comminution intensity, while the energy consumption increases together with increasing of feed material moisture. Investigations on olivine sand feed [11] showed that crushing ratio decreases for higher moisture, especially when the material is crushed at higher pressing force. HPGR devices, however, shouldn’t be regarded as a unique and perfect solution for comminution of each type of material. But they indeed may bring technological and economic benefits, comparing to conventional crushing and grinding machines, resulting in more favourable breakage of material particles and lower consumption of energy per unit mass of processed feed material.

Feb 1, 2025

By Alix Thierart, Yann Rouillard, Bernard Catalano

Bessac's presence in Singapore started in 2014 with the construction of the Thomson metro line, which includes 18 miles of twin-bore tunnels and 22 stations split into 17 construction packages. Bessac joint venture was allotted the T219 lot. The works include the construction of a new 660-foot (200-meter) long transfer station, two parallel 19-foot (5.8 m) ID tunnels and a pedestrian underpass. The urban context and the very soft ground stratum imposed to utilize unusual tunneling techniques, from upgrading a slurry TBM to a high-density slurry TBM to launch with very low cover and canopy pipe roofing completed with a MTBM without retrieval shaft.

Jun 23, 2024

By Ian Sherrell, Christian Cardoso, Henri Vepsäläinen, Guillermo Bermudez

Performance of mixing mechanisms in flotation cells is paramount, as inefficiencies can lead to financial losses through valuable minerals lost to tailings. Technological advancements have been implemented in flotation cells to optimize performance, but regardless of the efficacy of these developments, room for improvement may persist. Since its launch in 2005, FloatForce® has set a high industry standard for flotation mixing mechanisms. However, current mining trends call for sustainability-driven developments while improving metallurgical performance. Metso has recently introduced FloatForce®+, the latest iteration of FloatForce, developed through extensive laboratory, pilot, and industrial testing, aligning with mining sustainability trends. It has been designed to maximize recovery, reduce power draw and optimize manufacturing materials. This development stems from a redesigned rotor profile paired with a harmonizing stator configuration. This paper presents the development journey of Metso’s latest patented flotation mixing mechanism, an advancement to improve metallurgical performance at a high sustainable standard in flotation cells. The theory, CFD modeling and test work are discussed in detail.

Feb 1, 2025

By G. Vogt

Water is one of the most important ressources of our planet. Unlike many other natural resources, water cannot be substituted by anything and must therefore be handled with the utmost care. Depending on the region and the possible shortage of water, the importance of water increases even further. Water consumption is not the only factor. In the construction industry, water pollution from auxiliary and operating materials and processes as well as other contaminants and their resulting load on wastewater play an important role. The sources for wastewater on tunneling construction sites are various: Washing water, seepage water accumulating in construction pits, tunnel water, water used in the slurry circuit in fluid-assisted tunneling methods or water from concrete work and stone cutting all these waters are contaminated with a range of pollutants like solids, hydrocarbons, heavy metals, etc. These contaminants can be removed or treated/reduced with the help of specifically designed wastewater treatment plants (WTPs). After the treatment the cleaned water can be either, in best case, reused on the construction site itself or discharged into water utilities like the available sewer or river pin respecting their discharge requirements. Due to dwindling water resources globally, the continuously rising discharge limits and the ever more important aspect of sustainability the use of WTPs on tunneling construction site will be indispensable. In this paper, it will be presented how these systems are designed and work, what advantages they offer environmentally as well as financially and what to look out for when planning and implementing such a system onto jobsite.

Jun 23, 2024

By Richard Giffen, Martha Gross, Luca Pellegrini, Pa Ousman Njie

The Hampton Roads Bridge-Tunnel (HRBT) Expansion project in Virginia includes parallel 1.5- mile (2.4 km) tunnels constructed using a tunnel boring machine (TBM). The TBM launching and receiving shafts were excavated within the footprint of two reclaimed islands abutting the navigation channel for the Port of Virginia. The shaft excavations—a circular tri-cell shaft at South Island, and a circular-rectangular twin-cell shaft at North Island—were supported by slurry walls up to 190 feet (58 meters) below the island surfaces. This paper describes specic design considerations for these shafts, as well as construction and uality-oversight aspects of their excavation and construction.

Jun 23, 2024