Search Documents

By A. M. Raichur

Flocculation of fine coal is usually accomplished with the addition of commercially available organic flocculants. Recently it has been shown that biopolymers derived from microorganisms can be used to flocculate coal. The biopolymers flocculate coal efficiently and render the coal surface hydrophobic. The increase in hydrophobicity can be utilized either to separate the coal flocs from mineral matter. It can also be used for reducing the moisture content of fine coal. In this regard, flocculation and settling tests of fine coal with biopolymers and synthetic flocculants was undertaken and the results are discussed here. Also, a transport model was developed for the time-dependent settling tests for fine coal.

Jan 1, 1996

By Arthur W. Ruff

Estimated reserves of high-grade iron ore at Serra dos Carajás total 16 billion metric tons and have an average grade of 66.7 percent iron, 2.2 percent combined silica and alumina, and 0.05 percent phosphorous on a dry basis. Hematite is predominant and no significant sulfur or other deleterious elements are present. Figure 1 illustrates the comparative magnitude of the Carajás reserves. Serra dos Carajás is located in northern Brazil, about 550 kilometers southwest of Belém, Pará. It is six degrees south of the equator between the Xingu and Tocantins Rivers. Both rivers flow northward toward the Amazon River. The greater part of the area is covered by thick jungle, and the most practical means of access is by air. Figures 2 and 3 show the location of Serra dos Carajás. Figure 4 shows the distribution of the major iron-ore deposits.

Jan 1, 1973

By D. A. Gulley, L. J. MacDonnell, William A. Vogely

INTRODUCTION Environmental impacts are most commonly associated with air and water pollution. Not- withstanding this fact, to many people the primary disruption caused by mineral extraction is the change in the character of the locale. That is, the environmental impact of mining includes, but is not limited to, the generation of residuals. The dramatic transformation of wilderness or rural land often creates strong reactions to mineral development. Thus, the basic issues of land use management are a useful addition to environmental discussion. In this section, we take up a discussion of federal, state, and local land use management regimes, along with a brief introduction to the potential role of economic analysis. Elsewhere in this volume, land management issues are discussed from other orientations, and the interested reader may wish to look there as well. Locatable Minerals on Federal Lands Legislation and Administration: Access to hard-rock minerals on the public lands is governed by the General Mining Law of 1872. This law declares that "valuable mineral deposits in land belonging to the United States . . . are hereby declared to be free and open to exploration and purchase . . . ." In order to initiate rights, prospectors are required to physically stake claims of specified sizes and shapes following basic procedures set by federal law which may be supplemented by the individual states. Rights to these claims are protected at the exploration stage so long as actual possession is maintained and diligent exploration activity is underway. If a valuable mineral deposit is discovered on the claim, the claimholder earns the exclusive right of possession as against private parties so long as the claim is properly maintained. To maintain this exclusive right the claimholder must per- form $100 worth of labor or improvements, known as assessment work, on each claim every year and make related annual filings with the U. S. Department of the Interior. If the existence of a valuable mineral deposit can be demonstrated, and other legal requirements are met, the claimholder may receive a patent giving full title to the claimed land, including the surface in most cases. The purchase price is either $2.50 or $5 .OO per acre. The Mining Law has remained largely un- changed by legislative amendment during its now more than 100-vear existence. However, while the law itself has not changed, its interpretation and administration have changed considerably. Written at a time of rapid western expansion of the U.S. following the Civil War, the intent of the law was to promote mineral development by inviting unrestricted prospecting and by selling the lands containing mineral deposits at a minimal charge. As federal land policy shifted from one of rapid disposal into private ownership to one of retention and management for a number of uses, mineral patenting requirements have been administered more strictly. The most critical issue concerns what must be demonstrated to establish the existence of a valuable mineral deposit. The so-called "prudent man" standard was established in the case of Castle v. Womble (19 L.D. 455 (1894)):

Jan 1, 1985

By James Boyd

JAMES BOYD 29.1-STAFF-AND-LINE ORGANIZATION Industrial organizations are established primarily to coordinate the activities of many individuals working toward a specific goal. In mining, the goals can vary widely, and the skills necessary to reach them likewise will vary from operation to operation. It is essential to keep in mind the principal point that an organization embodies the necessary skills which supplement each other and achieve a given objective. Those who direct such an organization are grouped together as "management" and accept the responsibilities for the regulation, administration, supervision and guidance of the enterprise. Those who comprise the "administration" and have supervisory authority are referred to as the "executives." In the early days of mining it was common for one executive to exercise virtually complete control over the entire organization, and direct its operation from a central office. However, the science of management has advanced significantly since then. Mining organization administration now allocates increased authority and flexibility to those in direct-line responsibility, and organizes competent people in specialized fields to provide supervisors with guidance where it is needed in day-to-day operations. Few mining companies today are confined to one operation. Therefore, highly developed skills can be provided in the staff which assists management. This is known as staff-and-line organization, illustrated, in general, in Fig. 29-1. Each operation requires diverse skills for the carrying out of specific functions. The acquisition and training of those with such skills is an important operation in assembling organizations. An organization normally is modified to accommodate individuals rather than being a "hard and fast" mold into which people are fitted. The modern manager is inclined to organize to minimize central direction, with delegation to line executives, providing staff whose day-to-day operations, in cooperation with line executives, coordinate a continuing drive toward the organization's objectives. The staff officers, therefore, tend to become what could be described as parts of the president's brain, dealing with specific areas requiring certain skills. They do not necessarily direct operations, but watch them to be sure that the skills which they have themselves developed can be transmitted to line operations by persuasion rather than by direct authority. The elements of management requiring staff assignments are: 1. Planning, which, at staff level, is only a coordinating activity. Planning is done at all levels in the organization. 2. Engineering. 3. Finance. 4. Control. 5. Personnel and industrial relations, which set personnel policies, including salary plans and the means of handling relations with the unions. 6. Research, which, in a modern organization, is essential to progress and needs to be overseen at the top. 7. Legal staff to see that all operations of the company are provided with sound legal advice, and that the company's policies stay within the law.

Jan 1, 1973

By Donald D. Born

Mine No. 95 is located in Harrison County about 5 miles west of Shinnston, WV, with coal properties covering the northwest corner of Harrison County and the southwest corner of Marion County and with adequate Pittsburgh seam reserves to support the mine for many years. The mine was opened in 1967 and was planned, projected and operated as a room and pillar mine. It is located on a spur branch of the Baltimore and Ohio Railroad, has rail loading facilities and shipped by rail during its development stage. In 1972 it was converted to a mine mouth power station supplier and now transports coal by conveyor belt directly to the Harrison Power Station of Allegheny Power System. In 1971 the first longwall unit was installed in a selected area of the mine and immediately an orderly system of planning was developed to overcome the restrictions associated with longwall mining. The first was the development of the technique necessary for the plugging of abandoned oil and gas wells that existed in the area. With the assistance of the Morgan- town Energy Research Center of the Bureau of Mines, this restriction was overcome and thus opened a great potential for longwall mining in northern West Virginia. Other restrictions that had to be considered for longwall planning were dwellings and other improvements, snap top zones, water courses, and adequate bleeder systems, and the handling and treatment of mine drainage. In 1975 the second longwall unit was installed and soon therefore became a total longwall mine.

Jan 1, 1986

By Clinton Strachan, Dirk J. A. van Zyl

11.1 INTRODUCTION This chapter outlines some of the selection and design considerations for leach pads and liners. Leach pads and liners are generally chosen to provide the required or desired levels of low permeability and foundation conditions at minimum cost. The selection and design of a particular liner depends upon its anticipated use and performance, and what materials may be available. A leach pad is the firm base for a heap. When geomembrane liners are used, the pad is the firm, compacted foundation upon which the liner is placed. In the case of a clay liner, the clay liner is usually also the pad. It is important to consider the design of a pad or liner in terms of a system. The "leach pad system" consists of the prepared foundation, bedding layer (if used), liner (s), seepage collection or detection layer (if used), and cover layer. Foundation preparation is necessary to ensure a stable base for the rest of the leach pad system. A bedding layer is used to protect a liner from being punctured by large angular fragments in the foundation material. A seepage collection or detection layer, consisting of well-drained material and (sometimes) pipes draining to a collection sump, is included when a double liner is used. A cover layer on top of the liner can serve the following purposes (van Zyl and Strachan, 1986): • Preventing of ultraviolet light exposure to sensitive geomembranes; • Limiting evaporation from compacted clay liners and thereby eliminating cracking of such liners; • More efficient collecting of leachate; and • Protecting the liner from damage during heap construction. Economic evaluations of alternative liners for a project must include the overall system. For example, a geomembrane liner may require different foundation preparation and cover material selection and placement than a clay liner. Liners can be made of compacted clay onsite, amended soil, or geomembranes. Geomembrane is a generic term that has been proposed to replace many terms, including synthetic membranes, polymeric membranes, plastic

Jan 1, 1988

By Donald L. King, Frank A. Baczek

Sedimentation-based equipment is used in applications where separation of solids from liquid by gravity settling is desired. If a concentrated solids slurry is desired, the equipment is designed to "thicken"; if a clear liquid is desired the equipment is designed to "clarify." Thickeners normally handle higher solids loading rates than clarifiers, which usually process feed slurries containing low concentrations of suspended solids. Thickeners are therefore designed for heavier-duty requirements, and clarifiers have extra features to ensure more complete suspended solids removal. Major components (Figure 1) that are common to all sedimentation-based equipment are: tank, drive-support structure, drive unit and lifting device, rake structure, feed well, and a means of overflow and underflow withdrawal. Specific features are designed interdependently after the overall separation approach is defined conceptually. This conceptual approach is usually based on past experience or evolves from sedimentation studies conducted on samples of the slurry to be handled. Because many variations and combinations of components are possible, the overall conceptual approach has a number of possible designs that will accomplish the desired results. The final choice is based on practicality, potential for minimizing upsets, and cost.

Jan 1, 1986

By C. Cigna, M. Patrucco, D. Savoca, E. Lovera

The paper deals with the activity program and the preliminary results of a research work commissioned by IReR Research Centre and Regione Lombardia to the Department of Land, Environment and Geotechnologies of Politecnico di Torino. The aim is to define measurement, analysis and control criteria for the emission of chemical and physical pollutants from non-metal mining industries, with particular reference to noise and airborne particulates. Such emissions are related to health risks and annoyance problems, both for the working crews and the neighbouring population, and so, in order to get an effective sustainability of the industry, suitable reduction methods and assessment tools are required. A simple technique for the evaluation and forecasting of both the emission levels and deriving impact has been tested at different mining and quarrying sites, considering their differences in terms of layout and exploitation method, the latter ascribed to a series of main typologies as present in Lombardia region.

Jan 1, 2005

By Walter R. Jr. Hibbard, William A. Vogely

INTRODUCTION Volatile markets and pricing, increasing imports, constraining but effective laws related to the environment, health and safety and price controls lead to concerns which generated pious laws stating non-fuel policy and authorizing studies but resulting in ineffective implementation. Several commissions, reports by the Secretary of Interior and even the President have led to many recommendations but little or no action. No single comprehensive policy could solve problems which are diverse, commodity specific and not categorizable (Landsberg 1982, 1983). Thirteen laws administered by 27 agencies regulate or affect minerals and materials. Political instability created by communist regimes in Southern and Central Africa jeopardized sources of critical imported materials. This situation led to a Resource War mentality. It was feared that the U.S.S.R. was seeking to control this area and exclude the United States from resources (Vogely, 1980). The success of the Organization of Petroleum Exporting Countries with a petroleum cartel led to fears of an Organization of Minerals Exporting Countries which might create more cartels and/or make the existing ones more effective. Economic needs of developing countries required export to maintain employment and balance of payments have led to world surpluses, weak markets, low prices, and large loans from the World Bank which have under- mined U.S. industry (Landsberg, 1982a). Un- cooperative environmental laws, obsolete facilities and non-competitive costs have led to shipping U .S. ores to other countries for processing into ingot and bars which are imported back to the United States. Yet massive internal turmoil has interrupted supplies, and led to un- certain availability and higher prices. This situation could happen again. Included in this category of critical materials with uncertain sources are metals required in the manufacture of military aircraft, which has led to concern regarding the defense industry base (Morgan 1983). Remedies have been proposed which include: updated stock piles, material substitution, international cooperation and coordination, foreign policy aimed at resolving racial and national stresses in South and Central Africa, relaxing U.S. environmental and public land regulations and action under the Defense Production Act (Goth 1982). The President's report (1983) to Congress has stated a national materials policy which recognizes: that materials play a critical role in our economy, defense, and standard of living; that public lands contain a vast untapped mineral wealth; that the role of government is to identify mineral issues and act on them; and that there is a need for long term high potential pay off research (Bureau of Mines 1983). There is a serious question as to whether or not a comprehensive national mining, minerals, and materials policy is feasible let alone necessary. One solution is to abandon the attempt at comprehensiveness and to target specific is- sues with realistic policies (Comptroller General 1979). In the following sections, the major studies of the 1970s will be reviewed, major issues yet to be faced will be identified, the principles involved in these resolutions will be reviewed,

Jan 1, 1985

By J. Engesser

A research project supported by the Minnesota Department of Natural Resources and the Iron Ore Cooperative Research Committee was undertaken to reduce the dissolution of fluoride into process water during taconite processing. Leach tests were conducted using rod mill feed samples and water containing varying concentrations of calcium and sodium. Laboratory liberation grinds were performed to evaluate fluoride rejection during grinding and magnetic separation. Tube furnace tests were conducted to evaluate fluoride volatilization during pellet induration. The results indicate that fluoride concentration of process water is a function of both calcium and sodium concentration in process water. It appears that less than 1 percent of the fluoride present in rod mill feed will dissolve in process water during grinding. More than 90 percent of the fluoride present in rod mill feed is rejected with tailings during size reduction and magnetic separation. The furnace tests demonstrate that bentonite and fluxstone (calcite and dolomite) addition to taconite concentrate during pellet production increases the amount of fluoride that volatilizes during induration. Lime hydrate addition to pellets decreases the amount of fluoride that volatilizes during pellet induration. During acid pellet production approximately three times more fluoride enters the water during induration-off-gas scrubbing than during grinding. When fluxed pellets are produced three to eight times more fluoride enters the water during off-gas scrubbing than during taconite grinding.

Jan 1, 2004

By Curtis A. Pledger, H. Lee Wimmer, I. Michael Gowring

The Upper Diamond Fork Project, as part of the Central Utah Project Completion Act, conveys water six miles from the existing Sixth Water Aqueduct to the Diamond Fork Pipeline. During design, a Value Engineering team proposed a single-tunnel alignment that would be less destructive on the environment and might have a lower life cycle cost than the proposed design of two tunnels connected by two pipelines on steep hillsides. A decision was made to include this option in the bid process as a design-build alternative. The bid for this option was the lowest and a contract was awarded. During the TBM excavation a segment of tunnel wall caved in containing large quantities of water saturated with extremely high levels of hydrogen sul?de (H2S)gas (measured at 380 to 520 ppm in the air). The Central Utah Water Conservancy District (District) in consultation with Obayashi/Clyde (Contractor) quickly developed anew plan to finish the system by incorporating parts of the original tunnel/pipeline concept and re-bid the remainder of the project as a Phase 2 Design-Build contract.

Jan 1, 2003

By Frits Agterberg

Statistical exploration uses statistical methods to identify targets for more detailed investigation by estimating the odds of occurrence of mineral deposits. The study area which contains the possible targets may be as large as 1 000 000 km2 or as small as 100 km2. Results are presented in terms of a probability index for the existence of a deposit or, more precisely, in terms of expected dollar value for a unit area, or even in terms of number, size, and grade of deposits remaining to be discovered. Typically, selected geological, geophysical, or geochemical information is systematically quantified and statistically analyzed by using the computer in order to distinguish between geological environments on the basis of the probability that they contain undiscovered deposits of a specific type. All possible targets are compared with one another by using information on areas known to contain deposits. The information on the known areas is either a set of control data consisting of values for the same parameters as are quantified for the entire study area, or it embodies a specific model for the occurrence of a given deposit type. Examples of both procedures will be discussed in this chapter.

Jan 1, 1979

By Duane B. Jorgensen

The two calcium sulfate minerals, gypsum and anhydrite, occur in many parts of the world, and gypsum has long been of economic importance in the family of industrial minerals. Gypsum, the dihydrate form of calcium sulfate (CaSO, . 2H20) and anhydrite, the anhydrous form (CaSO,) are frequently found in close association, and it is seldom that a calcium sulfate deposit will consist exclusively of one mineral or the other. Although known gypsum deposits are extensive, anhydrite makes up the larger part of total calcium sulfate resources. Although it has very minor economic use, it is important to the understanding of gypsum deposits and is referred to frequently in the following discussion. Calcium sulfate is one of the principal constituents of evaporite deposits, and when pure, has the following composition: [ ] Deposits of pure gypsum or of pure anhydrite which are large enough to be considered commercial have not yet been found because of both the metastable relationship between the two minerals, and the presence of impurities such as calcium or magnesium carbonates, chlorides, other sulfate minerals, clay minerals, or silica. Most gypsum produced ranges from 80 to 95% pure and beneficiation is normally limited to selective mining or quarrying or upgrading by crushing and screening during mill processing. END USES The largest use for gypsum is based upon the unique property which calcium sulfate has of readily giving up, or taking on, water of crystallization. With the application of a moderate amount of heat in a process known as calcining, gypsum is converted to plaster of paris, the hemihydrate of calcium sulfate (CaSO4 ½ H2O), which when mixed with water will set or harden as the calcium sulfate returns to the stable dihydrate form. This semifinished product, usually called stucco, is then manufactured into a large variety of plasters, wallboard, and block for construction use, or into plasters for industrial applications. About 75% of the gypsum used in the United States is calcined for these purposes. Uses of uncalcined gypsum are principally as a retarder for portland cement, as a soil conditioner, as a mineral filler, and other minor industrial applications. About 25% of the gypsum mined in the United States goes into these markets; however, in other countries with building practices different from those in the United States and Canada, relative usage varies widely. Calcium sulfate deposits are the world's largest sulfur resources; minor quantities of gypsum and anhydrite have been used to produce sulfur or sulfur compounds. This use is accompanied by a unique site-specific set of economics because sulfur is generally available from non-gypsum sources at lower cost.

Jan 1, 1994

By Richard R. Klimpel

INTRODUCTION Previous papers by this author have discussed some of the difficulties involved with optimizing the performance of industrial flotation circuits, e.g. Klimpel (1988, 1989). The two major problems seem to be: 1) the inherent "systems" nature of the froth flotation process which leads to a great deal of self-compensation among the various operating options available and 2) the inherent variations in mineralogy, water chemistry, etc. that always seem to be present in industrial operations. In particular, the influence of reagent dosage has been emphasized in the above referenced work including an industrial system interaction denoted as the R/K trade-off, Klimpel (1984, 1987). Using a simple two parameter model for fitting time - recovery data, Klimpel (1980): [ ] where r is cumulative recovery at time t or at the t th cell, R is the long-term equilibrium recovery and K is the first-order rate of mass removal from the cell (time ), the definition of the R/K trade-off with increasing reagent dosage can be given as follows: at low dosages both R and K increase, at intermediate dosages R continues to increase but K starts to level out, and at high dosages, R may flatten out or still continue to increase but K starts to decrease, sometimes rather quickly. An illustration of this effect in a batch laboratory flotation cell is given in Figure 1. The purpose of this paper is to give a detailed plant illustration of this R/K trade-off phenomena with changing collector dosage which shows just how highly interactive the grindinglflotation system in sulfide mineral processing really is. This is one of about 20 plant level case studies that are being presented and evaluated in an upcoming book, Klimpel (1990). The particular study given here was completed in late 1979 on a copper ore of head grade 0.93% Cu. The frother being used was Dowfroth* 250 at a constant dosage of 0.15 g for each ton of solids feed to the rougher bank and the slurry pH was 10.2. The motivation of the study was to better understand the relationship of changes in feed rate (hence in particle size and state of liberation) with variations in collector dosage (potassium amyl xanthate). The major concern was to determine how much extra economic benefit could be gained by better utilizing the existing grinding mills and rougher bank consisting of eight identical cells. The remainder of the flotation circuit was also studied, including regrinding of rougher tails, but did not prove as critical as the rougher bank operation itself. It appeared from an overall economic viewpoint, the battle was being won or lost in the manner in which the rougher bank was being operated. This was not to minimize the roles of the scavenging and cleaning circuits but those portions of this particular circuit could be rather obviously operated to achieve maximum benefit given the specific output of the rougher bank. A special attempt was made to maintain constant ore type throughout the entire test program. Eight specific test conditions were evaluated including three different feed rates (and hence three different size distributions) to flotation. Tables 1 and 2 summarize the eight test conditions and overall recovery results at the end of the rougher bank for each test. A single test consisted of at least three consecutive eight-hour shifts operating at steady-state with composite cell lip samples taken over the final eight-hour shift. "Trademark of The Dow Chemical Company

Jan 1, 1990

By R. K. Mehta, M. G. Bersch

Characterization of an ore or mill product is routinely performed by time consuming and tedious chemical analyses, sink-float separations, etc. Additionally, these types of tests do not provide data concerning the interrelations and interlocking of the mineral constituents. This paper discusses some of the applications and capabilities of the Minerals and Material Science Research Center at The University of Alabama. Back-scattered electron images of coal, oil shale, complex suldfide, and tantalium ores were acquired using a JEOL 8600 electron microprobe with a NORAN (formerly Tracor Northern] 8500 image analysis system. Methods of analysis and typical results are discussed.

Jan 1, 1992

By W. Jacobi, F. Steinhausler, A. C. James

INTRODUCTION In 1979 the Committee on Radiological Protection and Public Health of the Nuclear Energy Agency (OECD) defined a programme of work needed to improve radon dosimetry and monitoring. A Group of Experts in this field was established by the NEA and at the first meeting of the Group the authors were designated an initial task with the following terms of reference:- To review dosimetry of radon, thoron and their daughters, and in particular:- - to examine analytical models for the assessment of dose to individuals who are exposed to aerosol mixtures of these nuclides; - to examine the state of knowledge of the characteristics of aerosol mixtures of these nuclides and other factors that influence the dose to the lung, and identify those parameters which should be measured for dosimetric purposes in radiological surveillance programmes; - to identify areas where further study or research are needed. In this presentation we attempt to examine, with these objectives, the relationship between exposure to radon and thoron daughter aerosols expressed in terms of the working level month l (WLM), or its SI equivalent, and dose accumulated by sensitive tissues of the lower respiratory tract. Over the past two decades many attempts have been made to calculate the lung dose equivalent to l WLM exposure in mine atmospheres, usually in terms of the maximum dose to basal cells in a small part of the bronchial tree. The calculations have employed variously detailed models of airway anatomy, aerosol deposition, ciliary clearance and dosimetry of tissue at the bronchial surface, and are well reviewed elsewhere (Walsh, 1970; UNSCEAR, 1977; Jacobi, 1977; Fry, 1977). They agree in the conclusion that basal cells in segmental bronchi (between about the third and fifth bronchial generations) receive the highest dose, although estimates of this dose differ by more than an order of magnitude, ranging from about 0.2 to 12 rads per WLM (2 mGy to 120 mGy). The most critical parameters of these models are the assumed depths of basal cells below the bronchial surface and the fraction of the WL carried by free ions. When more realistic values of these parameters are substituted (Jacobi, 1977), the dispersion in calculated maximum doses to basal cells is reduced to give a much smaller range from about 0.3 to 1 rad/WLM (3 to 10 mGy/WLM). The parameters and methods employed in these various models, however, remain too diverse to infer the sensitivity of the dose conversion to practical variations in aerosol characteristics and the additional factors determining lung deposition and clearance. We have therefore taken the approach of developing newer models (Jacobi and Eisfeld, 1980; James et al, 1980) that can encompass the range of available experimental data on the physical and biological behaviour of radon and thoron daughters and also accommodate the different interpretations that can be put upon them. We have paid particular attention to the averaging of dose over tissues of equal sensitivity in the lung

Jan 1, 1981

By J. Engesser

A research project was undertaken to determine if coal addition tofluxed-magnetite pre-fired pellets would reduce nitrogen oxide (NOx)emissions during pellet induration. Iron oxidation rate tests, coal oxidation rate tests and calcination rate tests were conducted in a laboratory furnace to determine the amount of coal necessary to provide adequate heat for limestone calcination without producing detrimental effects to magnetite oxidation. Pilot scale pot-grate tests were then performed with and without coal in the pre-fired pellets to verify pellet quality parameters and nitrogen oxide emissions. The off-gas during each pot-grate test was analyzed for NOx, CO2, CO, SOx, and O2. There was approximately a ten percent reduction in NOx emissions with coal addition during the normal pot-grate firing cycle. There was a 75% reduction in NOx emissions during firing cycles that used 25% to 75% excess air during firing rather than the normal 300% excess air.

Jan 1, 2003

By T. Negeri

The simultaneous use of two or more families of collectors can sometimes improve one or more key flotation performance indicators, especially if the ore under consideration contains several minerals bearing the same metal. The maximum amount of collectors that can be used is limited by the need to maintain a high concentrate grade and selectivity. Therefore, when more than one collector is required, an experimental design that allows variations of both the proportions and the amounts with respect to other process factors has to be selected to find the optimum dosage. This type of design is known as "process factors in mixture amount experiment". It is a powerful design suitable for discovering the existence and evaluating the magnitude of the interactive effects between various flotation parameters. This paper elaborates the principles on which such a design is based, and demonstrates its usefulness with a case study.

Jan 1, 2003

By Jessica M. Wempen, Dallan J. Coons, Bailey S. Simmons, Michael K. McCarter

Gate-road yield pillars are subject to increases in stress as the longwall face advances toward the pillars. Increases in pillar stress can be inferred by measuring roof/floor convergence surrounding the pillar. This paper presents a case study of convergence measurements surrounding a two-entry gate-road yield pillar in the head gate of a coal mine. Convergence was measured over a six-month period, as the longwall face approached and passed the pillar. Measurements were collected at eight locations surrounding the pillar: four locations in the travelway and four locations in the beltway. In addition to convergence stations, the pillar was instrumented with an array of seismometers. In future analysis, convergence measurements will be compared to seismic interpretations. This study reports on the geology and geometry of the longwall panel, the roof and rib support, the change in convergence over time, and the physical properties of coal and parting. Additionally, the convergence measurements are compared to pillar safety factor distributions derived from a finite element model. The convergence measurements contribute to the knowledge of when yield pillar abutment loading, caused by the encroaching longwall, is first detected. Knowing when abutment loading begins to yield the pillars can help define when standing secondary roof supports are required for head gate entry support.

By Natasa Mitevska, Predrag Djordjevic, Zivan Zivkovic

This paper presents the results of an experimental investigation into the distribution of copper in the slag of an industrial reverberatory furnace sulfide concentrates smelting process in the copper smelter RTB Bor (Serbia). The influence of copper content in the matte, the temperature and the height of the slag on the content of copper in the slag was determined as Cuoxide, Cusulfide and Cutotal and was based on possible mechanisms for the loss of copper in a silicate slag from the smelting of sulfide copper concentrates. The greatest quantity of copper in the silicate slag was found in the form of matte particles, which were captured in the slag as a result of the “flotation” of SO2 gas which was formed by magnetite reduction with FeS at the slag–matte interphase boundary.