Search Documents

By J. W. Craven, M. Katom, K. M. McCaffery

At Ok Tedi, ore type and SAG feed size distribution vary widely and frequently. This makes control of the SAG mills by application of the power/pressure relationship difficult. Power logic has traditionally been conservative due to power spikes associated with rapid size-distribution changes. A new expert system was installed in early 2000. The system incorporates multiple state fuzzy logic to deal with frequent and radical ore type and size variations, along with monitoring of motor temperatures. A short-term power spike no longer warrants immediate radical action. This has resulted in increased mill throughput and improved circuit stability. Key words: SAG mills, Mill control, Fuzzy logic

Jan 1, 2003

By H. Sevim

In long-term open pit production planning, a series of nested and maximum-value pits is usually generated first. These pits are then considered as possible pushbacks over a number of planning periods. To determine the best pushback in each planning period, the pits are evaluated for their technical and economical feasibilities under certain production constraints. Parameterization is a commonly used technique to generate a series of pits. In almost all cases, however, some of the consecutive pits generated by this technique are too far apart from each other. This is called the "gap" problem. It may make the entire pit series useless for production planning purposes. A new pit gener¬ating algorithm has been developed to overcome the gap problem. Through this algorithm, a series of nested maxi¬mum-value pits can be generated with a controllable size increment. The logic of the algorithm is illustrated through a small hypothetical case. Its capability of generating maximum-value pits that are as optimal as those generated by parameterization and its advantages over parameteriza¬tion are presented through an actual gold deposit case.

Jan 1, 1996

By J. N. Carras, N. W. Bainbridge

In order to further the understanding of spontaneous heating of longwall goafs a numerical model was developed, based on conservation principles applied to the transport of heat, water vapour and oxygen across the god Advective air flow into the goaf is caused by the differential air pressures across the god The air velocity field within the goaf area was computed using Darcy's law. The boundary and initial conditions concern air pressure, temperature and relative humidity. The oxidation rates and heat generation rates of the goaf materials required for the simulation were obtained from laboratory measurements. The main outputs of the model are temperature, oxygen and water contour maps, the rate of air leakage into the go4 velocity field and pressure distribution across the god. The model while still in its development stage, is able to simulate a heterogenous goafs constructed from different materials with different thermal and mass flow properties. Validation of the model by comparing its output with measurements from within goafs is required before the model can be used with confidence in a predictive sense.

Jan 1, 1995

The processing capability of a semi-autogenous (SAG) mill is greatly affected by ore geology and operating variables within the mill. The SAG mill is problematic because it cannot be conveniently studied on a smaller, laboratory-scale mill. The interior of the mill, where grinding takes place, cannot be observed using instrumentation available today. Yet the motion of the rock and ball charge determines the power draft and hence capacity of the mill. Therefore, mill optimization is pursued with a charge motion simulation software. This software uses the discrete element method to describe the individual motion of numerous ball and rock particles in the mill. It is shown that by simply increasing the chord length between the lifters and increasing the face angle of the lifters the capacity of the mill can be increased. Such a configuration of lifters allows the operator to increase mill speed, hence drawing higher power while considerably minimizing direct ball strikes against shell plates and lifters. A case study of a 36 ft. diameter x 15 ft. long mill is presented. Reducing the direct ball strikes leads to lesser steel consumption both in terms of balls and lifters.

Jan 1, 2000

By W. K. Utt, C. C. Woodward, W. L. Howie, G. G. Miller

The process of roof drilling and bolting is one of the most dangerous jobs in underground mining. In the United States, roof drilling and bolting results in about 1,000 accidents with injuries each year. Researchers, from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are studying the feasibility of using a drill-monitoring system to estimate the strength of successive layers of rock and assess the integrity of a mine roof. Such a system would allow roof drill operators to be warned when a weak layer is being drilled. Using measurements taken during drilling, a neural network can classify mine roof strata in terms of relative strength. The concept has been proven in principle. This research project was undertaken to increase the safety of underground miners, especially those involved in roof bolting. The system should be applicable to the mobile drills now used in underground mines, and the system would likely find wider application as well.

Jan 1, 2003

By Y. Théberge, V. Svalbonas, M. Fresko, E. Stopper

For many gearing applications, calculations carried out to AGMA standards are comprehensive. For very large gears, the elastic nature of the gear and pinion structures begins to play a larger role in determining the load distribution along the teeth. Various factors affecting the stiffness of the gear and pinion sets have been studied through FEA models for actual configurations. In particular, the effect of gear shape, load location, unsymmetrical structures, etc. have been studied in the unaligned and field aligned conditions. Analysis results show that the load distribution factor is highly sensitive to pin-ion stiffness, which affects gear structure design.

Jan 1, 2004

By J. E. Murphy, R. Y. Wan, K. R. Sandgren, M. C. Fuerstenau

As part of a U.S. Bureau of Mines program to evaluate alternatives to sodium cyanide in gold leaching, three organic nitrile compounds were tested for their effectiveness as gold lixiviante. The organic compounds examined were malononitrile, acetonitrile, and cyanoacetamide. The reagents were tested on an oxide ore, two carbonaceous ores, and a eulfidic ore. Acetonitrile and cyanoacetamide were shown to be ineffective gold leachante. Malononitrile was the most successful of the organic lixiviants. On an oxide ore, malononitrile performed shilarlyto sodium cyanide with extractions of around 80 pct. For carbonaceous "preg-robbing" oree, sodium cyanide was completely ineffective while malononitrile extracted 24 pct of the gold. When using a resin-in-leach technique, extraction with sodium cyanide increased to 60 pct and the extraction with malononitrile increased to 80 pct. On the sulfide ore, sodium cyanide and malononitrile performed similarly with 80+ pct extraction as long as the pH of the malononitrile solution wae maintained above 10.5. Malononitrile is six times less toxic than sodium cyanide as measured by LD, levels. Therefore, malononitrile has a significant advantage over eodium cyanide, but its high cost and undemonstrated usefulnees make it unlikely to gain acceptance.

Jan 1, 1993

By H. Sis, S. Chander

The pressure filtration behaviors of dispersed and flocculated alumnae slurries at high percent solids were investigated with the objective of determining the effect of surfactant type and concentration on slurry properties. A high-purity alumina powder was used as a model solid. Dispersion of the alumina was controlled by pH and by surfactants that are known to act as electric and steric stabilizers. The effects of both ionic and nonionic sutfactants were investigated. Surface charge measurements of the slurries were carried out by an electrokinetic sonic amplitude (ESA) method to better understand the mechanisms. The effect of surfactant type and concentration on the kinetics of pressure filtration and cake properties are discussed.

Jan 1, 2000

By Marie-Antoinette Dziurla, Barrie Johnson, Åsa Kolmert

Acidophilic bacteria are well known for their role in accelerating the oxidative dissolution of sulfide minds, such as pyrite. Other acidophiles, however, are able to catalyze dissimilatory reductive reactions. Bacteria that reduce ferric iron to ferrous, and sulfate to sulfide, were isolated from ARD-impacted environments and immobilised onto porous beads made of recycled glass. Column bioreactors containing colonized beads were constructed and peacolated with synthetic and actual ARD, and evaluated for their capacities to promote iron or sulfate reduction, and pH amelioration. Iron reduction did not require strictly anoxic conditions in bioreactors, and rates of up to 800 mg Fe3+ reduced/(l*day) were achieved, with a conversion efficiency of up to 98%. Using mixed populations of acidophilic fungi and iron-reducing bacteria, the bioreactors were capable of promoting iron reduction using paper pulp as sole carbon and energy source. Reduction of sulfate in pack bed bioreactors was observed with acidic wastewaters of pH 3 and above, though average rates of 300 mg sulfate reduced/(l*/day) were less than those recorded for circum-neutral pH systems. Bioremediation of ferric iron-rich ARD was assessed using coupled iron-reducing and sulfate reducing bioreactors.

Jan 1, 2000

By R. Hogg, T. F. Dumm

With increasing interest in the physical cleaning of fine coal, there is a need for extension of the sink-float analysis procedure to finer sizes. Problems arise, however, in ensuring complete dispersion of the particles in the heavy liquids. A procedure has been developed in which surfactants are wed as dispersing agents, and solids concentration is minimized (using a simple formula to estimate the minimum weight needed for statistical reliability). Using centrifuges to increase separation rates and subsieve particle size analysis of the specific gravity fractions, a complete size-specific gravity distribution can be obtained. Analyses have been performed on coal samples as fine as - 10 µm.

Jan 1, 1987

By G. T. Lineberry, W. J. Wiehagen, L. L. Rethi

This paper discusses a practical method for enhancing the performance of mining work crews. The method, described as the Work Crew Performance Model (WCPM), seeks to define performance variability within similar tasks of an underground work crew. Key components of the WCPM include: •job definition through task analyses, •the ranking of job elements by perceived cost consequence, •observational techniques to establish performance baselines, and •cost linkages between adherence to task procedures and measures of consequence for noncompliance. The components of this model emphasize a reliance on learning from a veteran work force and using that information to reinvest in strategies to enhance safety and efficiency. These strategies are not limited to technological efforts but include consideration of the so-called "soft-skill technologies, " aimed at reducing variability in individual performance and at effecting a continuous improvement in overall system effectiveness.

Jan 1, 1996

By F. M. Doyle, Jun Li, Milton E. Wadsworth, E. Peters

The Raman spectroscopic technique was used to study electrochernically oxidized pyrite in-situ. It was found that Raman-active sulfur oxidation products could be detected after a proper potential was applied to the pyrite electrode for a threshold period of time. There existed a minimum potential below which sulfur could not be observed. However, when the applied potential exceeded a certain limit, the intensity of the sulfur spectra decreased. The minimum potential at which sulfur could be observed changed with solution pH. For both acid (pH 2.7) and weak alkaline (pH 9.2) solutions, the minimum potential was 0.8 V/SCE, whereas for neutral (pH 6.5) solutions the value was 0.4 V/SCE. In strong alkaline solutions (pH 12.5) surface sulfur oxidation products could not be detected at any potential.

Jan 1, 1993

Conventional logging tools such as density, neutron, and acoustic have ranges of investigation of tens of centimeters. The borehole gravimeter, however, has a range up to hundreds of meters. For example, from the center of a cylindrical ore body 0.20 g/cm3 denser than its surroundings, one can detect the boundary of the ore body at a radius as large as five times its height. More complex structures can be investigated with computer programs. We can predict the usefulness of proposed gravity surveys, or decide which suggested structure is most likely to have caused the results of existing surveys.

Jan 1, 1988

By Ian Longson, Darron W. Dixon

This paper describes the results of an investigation into the application of a statistical method for the prediction of general air-body methane concentration in longwall coal districts. An important and necessary part of the research was the acquisition of representative monitored mine environmental and coal production data. The monitored data was used to build time series models of general air body methane concentration, air velocity, barometric pressure, coal production and methane drainage variables of differing timescales according to the Box-Jenkins method of time series analysis. The univariate models were used to identify causal relationships between methane concentration and its explanatory variables. Coal production was found to be the dominant variable in the determination of the quantity of methane emitted and where appropriate, multivariate time series models were built in which expressions for methane concentration in terms of coal production were obtained. Finally, forecasts of methane concentration values were generated from the multivariate models to determine their forecasting capabilities.

Jan 1, 1993

By M. A. Mahtab, N. M. Cruickshank, M. T. Wane

Gas outbursts occur as sudden eruptions of gas and minerals from the face of a mine heading as the heading approaches potentially burst prone (or anomalous) zones of rock. Such outbursts have resulted in considerable damage to equipment, and in some cases lives have been lost. Characterizing these anomalous zones and detecting their presence is therefore vital to safe mining. Certain significant characteristics associated with the outburst-prone zones are: (1) the presence of fluid inclusions, (2) unstable stress conditions, (3) characteristic geologic structures, (4) certain physical properties of the rock, and (5) microseismic activity. Geophysical and engineering methods for detecting these characteristics are discussed and are considered with respect to their past success and future potential for predicting gas outbursts.

Jan 1, 1987

By M. Abdel-latif, R. W. Bartlett, P. R. Taylor

A cyclone reactor system for the partial reduction and melting of taconite concentrate fines was designed and operated. A nontransferred arc plasma torch was employed as a heat source. Taconite fines, carbon monoxide and carbon dioxide were fed axially into the reactor, while the plasma gas was introduced tangentially into the cyclone. The average reactor temperature was maintained above 1673 OK (1400°C), and reduction experiments were performed under various conditions. The influence of the following parameters on the reduction of taconite was investigated: carbonmonoxide to carbon dioxide inlet feed ratio, carbon monoxide inlet partial pres- sure and average reactor temperature. The interaction of the graphite lining with carbon dioxide and taconite were also studied.

Jan 1, 1995

By Tim Neil, O&apos

Large is the applicable adjective here. The largest hydraulic shovel in the world, the largest copper mine in the world, the largest copper producing company in the world. The O&K RH 300 hydraulic excavator has been put into service to move overburden and mine ore at the Chuquicamata open pit mine of the Chilean state copper mining company, Corporation Nacional de Corbre de Chile (Codelco). A large shovel: Equipped with a 26-m3 (34-yd') rock shovel, the RH 300 is able to fill a 170-t (187-st) truck in three passes with cycle times of 30 seconds. A large mine: At present, the Chuquicamata pit is 4 km (2.5 miles) long, 2 km (1.2 miles) wide, and 520 m (1700 ft) deep from rim to bottom bench. The current 450 kt/d (496,000 stpd) of material mined will increase to 600 kt/d (661,000 stpd) when the expanded production rate is reached in 1989. (Chuqui Expansion details, p. 20). A large mining company: Codelco's total output from its two open pit and three underground copper mines is more than 1.1 Mt/a (1.2 million stpy) of copper. This makes Codelco by far the largest copper producer in the world. It accounts for about 15% of the Western World's copper requirements. Chuquicamata is located in the hot and arid Atacama desert of northern Chile. The mine is located 240 km (150 miles) northeast of the port city of Antofagasta. Mine elevation is 2700 m (8850 ft). Chuquicamata's known reserves of oxide and sulfide ores amount to more than 450 Mt (496 million st) of contained copper. There are also reserves of more then 1.4 Mt (1.5 million st) of contained molybdenum. Originally, Chuquicamata was a rail pit. The shovels loaded rail cars hauled by locis on tracks along the benches. During the 1970s, the rail transport was replaced by truck haulage. Crushing and conveying rock waste in the pit is the latest step in the continuing evolution of more productive and economical methods of materials movement. In 1990, the in-pit crushing plant will be in operation. The waste will be mainly transported out of the pit on belt conveyors rather than trucks. The system will incorporate a 9.6-kt/h (10,600-stph) semi-portable crushing station, a 14-km (8.7-mile) conveyor using 1.8 m (6 ft) wide heavy duty belts, and a tripper-spreader to stack the waste dumps. Since Chuqui went into production in 1915, more than 2.5 Gt (2.8 billion st) of material has been excavated. This includes nearly 1.7 Gt (1.9 billion st) of ore from which some 16.4 Mt (18 million st) of copper has been recovered. The Chuquicamata porphyry type ore body is an altered and fractured intrusive granodiorite or quartz-monzonite porphyry that carries the mineralization. The action of ground water on primary sulfide minerals in geo¬logic time has created oxide ores and a zone of secondary enrich¬ment. The oxides occur above the sulfide zone and are also mixed with the upper parts of the latter. At Chuquicamata, the current grade of 1.5% copper is expected to decline to about 1% by 1995. To maintain metal production at cur¬rent levels, it will be necessary to increase ore production rates by about 50%, as mentioned, to 153

Jan 1, 1988

By Don S. McCoy, W. Joseoph Schlitt, Donald B. Swanson

Introduction Contract miners have long played an important role in the minerals industry. Historically, these were individuals who worked as underground miners and were paid by the ton or the day. These hardy types still ply their trade in the industry. However, today the term "contract miner" generally refers to an independent contractor who supplies the people and equipment needed to conduct surface mining operations for an owner or lease holder. At one time or another, contract miners have probably handled virtually every mineral commodity from sand, gravel, and stone quarrying to mining uranium and precious metal ores. In today's market, though, contract mining appears to be concentrated in just a few areas. These include precious metal mines, various types of solid fuel operations, and reclamation of abandoned mines. This article covers market areas, contract mining organizations and services, and their advantages and disadvantages. Gold and silver mines Although exact figures are not available, contract mining represents a significant element in the precious metals segment of US mining. For gold and silver, the growth in contract mining appears to be paralleling the overall growth in mining activity itself. Nevada is the largest gold producer in the US. The latest available data (1985) on open pit gold/ silver mines is summarized in Table 1 (Nevada Division of Mine Inspection, 1986). These figures show that contractors mined nearly half of the ore in 1985. Total tonnage mined, of course, was much higher for both owners and contractors. Assuming an average stripping ratio of 2.5 to 1, the total daily mining rate for the contractors was more than 145 kt (160,000 st). This translates into a contract mining rate of about 36 Mt/a (40 million stpy) based on 250 operating days a year. This approximate 50-50 split between owner and contractor also appears to hold for the future. Metals Economics Group (1987) published a survey of 51 short-range and 54 long-range precious metal projects being considered throughout the US. Contacts with owners, requests for proposals, and past corporate philosophies all suggest that about 55% of the open pit operations scheduled for the near-term will be contract mined. This represents an estimated 26 kt/d (28.5 stpd) of ore. A similar assessment of the long-term projects indicates that about 12 kt/d (13,000 stpd), or just under 50% of the open pit tonnage will be contract mined. There are several reasons why gold and silver represent such an attractive opportunity for contract miners. One is that many properties are owned or leased by individuals or partnerships that are essentially entrepreneurial. Many of these owners or lease holders have minimal mining experience. They must therefore either rely on contract mining organizations, sell an interest in the project to another mining company that will become the operator, or hire an experienced management team. For about the same reason, junior mining companies also represent good prospects for contracting. This is because most junior companies focus on exploration. They would prefer to spend their generally limited funds on drilling programs. Thus, they tend to minimize additional capital requirements by using contract miners or farming out the property to another mining company. Another good reason for using contract miners is the size of the deposit. Many properties are so small that their reserves will not support the capital expenditures

Jan 12, 1987

By H. G. Naidu, Raj K. Singhai, S. P. Singh

Introduction The economics of open-pit mining de¬pend heavily on the cost of overburden removal. It is necessary to maintain a pit slope as steep as possible. Steeper slopes lower the volume of overburden to be handled, thus lower the cost of material handling. There is, however, a limit to which the pit slopes in any given situation can be steepened. Steepening beyond this point could jeopardize the pitwall stability, ren¬dering it unsafe. It might even result in curtailment of pit production. Several factors affect the stability of pitwalls. Some are natural, such as topogra¬phy and regional and local geology. Others are man made, such as pit geometry, ground water management, equipment, drilling and blasting, and the type of excavation. Greater control can be exercised in the latter with proper planning and by following a set of procedures based on field experiences. This article deals with one such control¬lable factor - drilling and blasting. The eco¬nomics of steeper pit slopes is discussed, followed by a record of drilling and blasting practices in western Canadian surface mines. Microprocessor-based instrumentation and its application to blasthole drilling is also described. Economics of steeper pit slopes The economics of steeper pit slopes is not a new issue. It should be reinforced, though, that pit slopes must be as steep as possible to ensure maximum recovery of minerals at a minimum stripping ratio. For operating, economic, and safety reasons, different pit slopes are maintained during different phases of pit development. Figure 1 shows a hypothetical ore body, cylindrical shape, with a radius of 225 m (740 ft) and located 30 m (100 ft) beneath the surface. The mining operations are planned at two different slope angles of 25° and 40°. The ultimate pit depth was established on the basis of the criterion of "break even pit." The variation of the stripping ratio at differ¬ent mine levels is shown in Fig. 2. Table I summarizes the eco¬nomics involved for two pit slopes, 25° and 40°. Figure 3 presents the profits during the life of the mine for these two pit slopes. This study shows that steeper slopes for an open pit operation are far more advanta¬geous than flatter slopes. But, what is the optimum slope at any one point in the life of a moving pit? And how can the stable slopes be maintained over the short- and long-term? Canadian blasting practices A survey of blasting practices in western Canadian surface coal mines revealed that, at most mines, hard consolidated overburden is drilled and blasted. Blastholes are drilled with rotary crawler-¬mounted rigs using bits in the 220 to 310 mm-diam (8.5 to 12 in.-diam) range. Typi¬cal hole depths are 12 to 18 m (40 to 60 ft) to accommodate the pit bench heights of 12 to 15 m (40 to 50 ft). For a 12-m (40-ft) high bench, a typical hole will be 14.6 m (48 ft) deep including the subgrade drilling of 2.6 m (8.5 ft). Half of this hole will typically be a powder column and half will be stemmed. For a 15-m (50-ft) bench, a typical hole will be up to 18 m (66 ft) deep including the subgrade drilling. Drilling patterns are usually 9 m (29.5 ft) spacing and 9 m (29.5 ft) burden. De¬pending on local geology and hole diameter selected, drilling patterns of 8 x 8 m, 8.5 x 7.3 m, and staggered patterns of 11 x 5.5 m

Jan 1, 1989

By G. Chi, M. C. Fuerstenau, R. C. Bradt, A. Ghosh

Technical Papers, Mining Engineering Vol. 49, No. 12, pp. 70-75, Discussion by McIvor, R. and Fink, R. P. We must challenge what we consider to be dubious statements in the above-mentioned article. Much of what is reported was published elsewhere over a year ago (i.e., in their reference: Chi, G., Fuerstenau, M.C., Brandt, R.C. and Ghosh, A., 1996, "Improved comminution efficiency through controlled blasting during mining," International Journal of Min¬eral Processing, Vol. 47, p. 93). There is nothing unusual or significant about a 10% or more difference in grindability between two materials of apparently similar origin and other attributes (such as chemical assays, hardness and specific gravity). Consider also that: • the materials came from different locations in the pit; • only two sets of four blastholes were considered per blast: • spatial orientation with respect to the face and other blastholes was also altered; • only two pairs of data were collected; • the impact of sampling error and bias, • both of which could be significant in this case; and • normal experimental error in parameter measurement and calculation. It is clearly inappropriate to draw any conclusions with regard to cause-and-effect relationships without first presenting a thorough error analysis. A substantial number of randomly selected test and control areas might provide meaningful statistical evidence of the claimed effect of the variables being studied. Even that appears doubtful, however, because Figures 3 and 4 show about as much variation in crushing energy for the two "regular" conditions vs. regular and altered conditions. On a separate, but also important issue, broad experience with autogenous/semiautogenous milling has shown that smaller or weaker feed material results in reduced tonnage. ? Reply Thank you for the opportunity to respond to the comments of Messrs. Mclvor ant Fink. The points raised are addressed in the order of presentation. As the commenters noted, there are parallels between this article and a previous manuscript. The reason for these complementary articles is that the audiences for the two publications are different, although there is obviously some overlap. We believe that the different audiences each profit from the technical aspects of the two manuscripts. We are not in agreement that a grindability difference of 10% is insignificant. The laboratory work is corroborated by data obtained at plant scale, which confirms that an increase in throughput of the same magnitude (between 5% and 10%) is achieved when the blasting pattern is modified, i.e., reduced from 9 to 8 m (29.5 to 26.2 ft). This increase in throughput translates into substantial power savings for ore grinding. No differences in appearance in the rock were noted between the two adjacent areas. Rock in both areas belonged to the same rock mass/block, which was quite homogeneous and without geological features in between that could create drastic differences in comminution characteristics. Given the resources, we would have sampled from all of the holes. Additional data would certainly have been desirable, as would have been additional funding to expand the study. Their comment, "spatial orientation with respect to the face and other blastholes was also altered," is not clear. Figure 1 does not show the initiation sequence. Without the initiation sequence, we do not understand how the commenters concluded that spatial orientation with respect to the face and other blastholes was altered. The commenters may be trying to make the point that the four-hole configurations with respect to the original bench face are not exactly the same. In fragmenting the

Jan 1, 1999