Search Documents

By Rick Wright, Gregory L. Raines

San Diego’s need to access underground space has dictated a long history of tunnel construction. The subsequent need for water, coupled with San Diego’s natural attractiveness, has led to significant population increases and the need for the construction of even more tunnels. This paper will provide a historical summary of the progression of mines, tunnels and trenchless technology construction projects that contributed to the advance of current technology, feasibility, and constructability. A bibliography of relevant reports and data is included.

Jan 1, 2001

By P. M. Soupios

There is an increasing requirement for geophysical surveys carried out during geotechnical investigations to provide direct information about rock quality or other geotechnical parameters. With the paucity of information to correlate geophysical results with actual rock properties, this is still difficult to achieve and additional research effort needs to be performed to address this issue. Nowadays, several researchers have been described detailed studies which designed specifically to investigate this matter. Generally, geophysical techniques which are used to estimate seismic velocities in the subsurface focus on the low strain levels that are not large enough to induce significant nonlinear, nonelastic stress-strain behavior (Luna and Jadi, 2000), which is normally evaluated when addressing liquefaction potential of soils in the shallow subsurface. Soil parameters relevant to seismic ground response (Rechtien, 1996) are density, relative density and void ratio, permeability, shear modulus, water saturation, soil fabric and stress history. Detailed characterization of elastic properties near a major construction site (e.g. a bridge) is useful for near field dynamic analysis of soil-structure interaction (SSI) effects. The coupled effect of the bridge foundation (piles, piers or abutments) and the soil immediately surrounding these substructure elements is essential for dynamic SSI analysis of these critical bridge structures. This paper presents a geophysical investigation performed along the under construction highway of Egnatia Odos, approximately 13 km west from the town of Xanthi in N. Greece. Twelve geotechnical boreholes, drilled at the maximum depth of 75 m, approximately located 20 m from the Nestos River. The objective of the survey was to obtain the high-resolution compressional and shear wave velocities of the shallow subsurface for computation of elastic engineering properties of the unconsolidated material interposed between the investigated boreholes. Joint interpretation of borehole logs and velocity images obtained by P- and S-wave traveltime inversions outlined shallow geological anomalies.

Jan 1, 2005

By A. J. Basu

Geotechnical design plays a key role in mine design. I A proper geotechnical design provides a safe working environment and facilitates efficient mining operation. There are mainly three design approaches I) judgmental, based on observational and experiential facts, 2) empirical, based on empirical design formulae, and 3) analytical, incorporating numerical analysis. Most design applications are based on the design methods one and two as mentioned earlier. However, complexities arise in deep underground mining operations and deep open pit mines. These complexities and difficult geological environment introduce more uncertainties and simple empirical formulae would not be adequate as a design tool. These situations require numerical modelling and analysis of the design problems including interpretation of the results obtained from the analysis. There are several tools available for performing the numerical modelling and analysis. A brief review of the available tools was addressed earlier (Basu and Kuruppu, 1995). The authors selected ANSYS (a general purpose finite element analysis tool) for use in mining geomechanics and geotechnical design. This paper includes several examples demonstrating the applicability of this software in designing structures applicable to mining geomechnics. The authors hope that the design examples will demonstrate the use of the numerical modelling and analysis application in excavation design.

Jan 1, 1996

By J. C. Stankus

Many coal seams are associated with soft floor strata and during mine development if coal pillars are not properly designed, floor heave occurs and causes interruption of coal production. In the severe cases, the section or mine is abandoned. One of the methods for controlling floor heave is floor bolting. This paper describes the demonstration of floor bolting methods in a West Virginia coal mine. Three methods were used: (1) vertical full resin bolting, (2) floor truss bolting, and (3) floor truss bolting plus a floor cut at the center of the entry. The design of each method and the experimental results are discussed in detail.

Jan 1, 1993

By G. R. Harrod

Effective mine operation demands that the right people have the right information at the right time. Caterpillar's Mining and Earthmoving Technology System (METS) meets this demand by providing "real-time" information transfer between the mine offices and machines equipped with the Caterpillar Computer Aided Earthmoving System (CAES). Transfers of mine plans from the mine planning software to CAES-equipped machines give operators access to current mine plans within minutes of their creation. Additionally, office personnel have access to a current digital terrain model (DTM) of the mine site as it is updated in "real-time" by CAES-equipped machines. METS provides mine personnel in operations, planning, and management the information they need when they need it.

Jan 1, 1998

By George E. Aikens

Prolonged subzero climatic conditions impose some unique engineering problems for the developer and operator of open-pit mines in the Far North. The remoteness of the job site and the extremely cold, long, dark winters severely tax both man and machine in the quest for the Arctic's rich mineral wealth. Undoubtedly the singular most troublesome problem for the engineer is Permafrost which underlies about 201o of the land area of the world and about 85% of the state of Alaska. Permafrost has its impact on building construction and mine excavation, while posing a more pervasive threat to the-delicate ecologic balance within the Arctic wilderness. Yet the difficulties associated with mining up North may not be as overwhelming as has been previously supposed. For example, the lowest temperature recorded at Point Barrow is -560F, whereas Montana has recorded -69.7° F.. There are no specially designed machines for mining and construction in the Arctic, and efficient equipment utilization is maintained through proper operation and servicing techniques. However, neither equipment or people can be assumed to function normally at -40°F. Special techniques in drilling, blasting, and ripping are being used to yield economically competitive ores. Overall, a fundamental understanding of the nature of Permafrost will allow the engineer to deal expeditiously with an Arctic mining venture and at the same time to deal fairly with Arctic environment.

Jan 1, 1972

By J. T. Hanks

Process development is one of the principal tasks required in the course of turning an exploration discovery into a mine. Exploration geologists should have an understanding of the more important metallurgical processes and the test work required for each process. The paper discusses the important metallurgical processes, the test work and sample requirements for each, and the costs and time requirements to accomplish the testing. The limitations of reverse circulation drill samples for metallurgical testing are discussed. The level of process definition required to support engineering studies: scoping, pre-feasibility and feasibility studies are also described.

Jan 1, 1997

By R. D. Hutchinson

I consider it an honour to be the opening speaker in this afternoon's session on "Canadian Exploration". I also think it most appropriate that this joint meeting of the MMIJ and AIME should consider this subject, because Canada is a major exporter of mineral products and Japan and the United States are our two largest customers. Clearly, therefore, both countries have a valid interest in developments on the Canadian minerals scene. I represent the Mineral Development Sector of the Canadian Department of Energy, Mines and Resources. I will therefore speak from the point of view of the Federal Government. At this point I would like to acknowledge the help and constructive criticism I have received from several of my colleagues in Mineral Development Sector in the preparation of this paper. In any discussion of exploration in Canada, it is essential to emphasize at the outset that Canada has a federal system of government, with powers shared between Ottawa and the provinces. Under our constitution, the federal government has jurisdiction over the north, and over offshore areas, while the provinces own the natural resources within their boundaries. They control the systems of land acquisition for exploration and the terns under which mining titles are issued, and are therefore able to determine the rate and conditions of exploration and development of these resources. It follows that the Federal Government can influence the exploration and development of the provincial resources only indirectly by consultation with provincial authorities. However, once the resources are developed and begin to flow to market, the Federal Government can exert a much stronger influence because of its constitutional right to control both inter-provincial and international trade, as well as through its general fiscal and tax powers.

Jan 1, 1976

By Ernest F. Giovannitti

A couple of years ago, one of the major television networks produced a series on the environment. One episode in the series dealt with the nation's solid waste problem and some of the research being done to solve it. It was interesting to listen to one researcher who was attempting to develop a glass that when broken would dissolve in water. It was said that using this glass would eliminate over 100 million tons of solid wastes each year. At first glance, it would appear that this research-effort would make a significant contribution to environmental pollution control; however, if one pauses to consider the water, he can see that this solution to the solid waste problem may well contribute to a water pollution problem. The dissolved material must either end up in our surface streams or be removed in waste treatment systems. Either alternative may have a more adverse effect on the environment than the original problem. With today's emphasis on the environment, it is important that the effects of our activities be studied in depth. Then, by properly planning the activity, the adverse effects can be minimized. The coal mining industry 100 years ago was in the same boat, as our glass maker, is today. Unfortunately, it too failed to consider all the effects of its activities and as a result, in Pennsylvania, there are over 5000 miles of streams adversely affected by coal mine drainage. The situation is improving, however, because mine operators are beginning to recognize and accept the methods for controlling coal mine drainage. The purpose of this paper is to discuss the measures for the control of coal mine drainage and to set forth the factors that affect these controls.

Jan 1, 1972

By Timothy J. Orr, Robin J. Burgess-Limerick, Jennica L. Bellanca, MARGARET E. RYAN

Powered haulage continues to be a large safety concern for the mining industry, accounting for approximately 50%of the mining fatal accidents every year. Among these fatal accidents, haul-truck-related accidents are the most common, with 6 of 28 and 6 of 27 fatal accidents occurring in 2017 and 2018, respectively. To better understand why these accidents continue to occur and what can be done to prevent them, researchers reviewed the 91 haul-truck-related fatal accidents that occurred in the USA from 2005 to 2018 and performed bow-tie analyses using the final reports published by the Mine Safety and Health Administration. The analyses explore the context of the accidents with a focus on the initiating event, event outcome, hazards present, and possible preventative and mitigative controls. Overall, the vast majority of the accidents resulted in a haul truck colliding with the environment, and the majority of these events were initiated by loss of situational awareness or loss of control. The majority of the hazards were related to design and organizational controls. The results of this study suggest a need to investigate operator decision-making and organizational controls and to focus on improving design and operation controls such as mine design and operational procedures.

Feb 22, 2021

By W. Choi

The present study revealed that the bioleachability of a chalcopyrite flotation concentrate is influenced by the semiconductor properties of CuFeS2. The overall reaction of biooxidation,

Jan 1, 1991

By J. R. Klaehn, M. Shi, T. E. Lister, L. A. Diaz, J. S. McNally

Since 2019, approximately two dozen international battery recycling companies have been operating at the commercial or pilot scale [1]. However, current process capacity does not exceed 100,000 tons of end-of-life (EOL) lithium-ion batteries (LIB) per year, and the current recycling rate is only about 5% in North America [2-3]. Recycling metals from EOL LIBs is not only essential to waste minimization and environmental stewardship, but also a source of critical materials, which can contribute towards supply chain stabilization. LIB recycling can be roughly divided into three categories: direct recycling, pyrometallurgy, and hydrometallurgy. Direct recycling seeks to retain as much of the manufactured effort with minimum chemical processing [4]. The evolution of battery designs and chemical compositions are challenges to this approach [5-6]. Pyrometallurgical processes are robust and flexible allowing a broad spectrum of batteries with minimum pre-processing requirements. Some of the matrix issues are solved through combustion of some constituents. Smelting is strongly tied to fossil energy and air emissions are a concern. In addition, pyrometallurgical processes are not stand alone, as hydrometallurgical refining normally required to separate and recover the metals of interest (Co, Ni, and Cu) from the produced alloy and Li from the slag [7]. Hydrometallurgical processes can be highly selective and efficient in recovering high purity materials [8]. In general, hydrometallurgical processes are considered cleaner and less costly than high temperature processes [4,9-10]. Extensive chemical consumption and waste generation significantly increase the operating costs and overall environmental impact of the hydrometallurgical processes [11]. Leaching of metals from LIBs is dominated by the mixture of sulfuric acid (1 to 4 M H2SO4) and hydrogen peroxide (1 to 15 wt.% H2O2) [10]. Although organic acids have been tested as lower environmental impact alternatives, the reported pulp density operations are low < 60 g/L [10-11]. For the H2SO4/H2O2 leachates, high leaching efficiencies >90% are reported for Co, Ni, Mn, and Li from cathode materials at temperatures over 40 ⁰C and pulp densities between 30 to 200 g/L [9-10]. H2O2 acts as reducing agent to convert Co+3 and Mn+4 into their soluble forms, Co+2 and Mn+2 [12]. Despite the claims of H2O2 being a clean reducing agent [13], production of H2O2 has significant environmental impacts as determined by life-cycle analyses [13-14]. Moreover, the costs and risks associated with H2O2 transportation and storage cannot be ignored [15].

Mar 2, 2022

By Brendan Demich, Joseph McGuire, Emily J. Haas

Near misses recorded and reported by workers can provide awarenessto the potential causes of injury and prompt safety management initiatives. Although most companies require near-miss reporting, it is unclear what the value of these reports are, if any, and how they influence subsequent actions or controls to reduce on-the-job risks. Researchers at the National Institute for Occupational Safety and Health (NIOSH) conducted a case study with an aggregates company in which near-miss reports were analyzed at each of their locations over an entire quarter during the summer of 2018. Within that quarter, workers recorded 249 near misses. Of those, 167 were valid near misses that occurred at work. Researchers coded the reports using a qualitative 5 × 5 risk matrix. Of the 167 near misses, 19% were deemed low risk, 25% moderate risk, 30% high risk, and 26% critical risk. Several patterns in the near-miss incidents were documented, including classification of incidents and common corrective actions referenced (i.e., elimination/substitution, engineering control or redesign, work process/procedures, and personal protective equipment). The analysis provides insight into ways that risk communication and management programs can be improved to reengage workers and their situational awareness on the job.

By J. Bilant, B. Carlson, N. Gow

"High-pressure grinding roll (HPGR) technology was evaluated to replace tertiary cone crushing at Coeur Rochester operations (Coeur Rochester Inc.) as an opportunity to improve silver recovery. In 2016 and 2017, onsite and third-party pilot programs were initiated to evaluate the impact on metallurgical recovery and heap leach performance of crushed product generated by an HPGR. In 2018, Forte Dynamics evaluated the HPGR laboratory metallurgical data from Coeur Rochester and all third parties to develop field-scale leach curves based on new crushing scenarios. The laboratory recovery test work data were consolidated and scaled to field conditions to determine projected heap leach performance. Based on the metallurgical testing conducted, the replacement of current tertiary cone crushers with HPGR technology has the potential to increase Coeur Rochester’s silver recovery rate by 8 percentage points, from 61 percent to 69 percent, and shorten the overall timing of silver recoveries from 20 years to just more than two years.The Rochester Mine, and associated valley fill heap leach facilities is an openpit silver and gold mine located in Pershing County, NV, approximately 42 km (26 miles) northeast of the city of Lovelock. In 2017, Rochester produced approximately 4.7 million oz silver (Ag) and 51,000 troy oz gold (Au). Ore mined at Rochester is either fed directly to the primary X-Pit crusher, crushed at an in-pit crusher system, or placed directly onto a heap leach pad as run-of-mine (ROM). Both crushing circuits are comprised of three stages of crushing to produce a nominal 3/8 in. ore. Primary crushing consists of jaw crushing while secondary and tertiary crushing are composed of varying cone crushers.Historical recovery rates of crushed Rochester ore averaged 61.4 percent Ag and 95.9 percent Au over a period of 20 years (Robinson et al., 2018). These rates were derived from third-party verification of in-house metallurgical test results, crusher production and heap leach production results from 1986 through 2004 in a private report for Rochester produced by KD Engineering Co., Inc. Recovery rates are regularly verified by compositing daily samples of ore delivered to each leach pad from the X-pit crusher, in-pit crusher and/ or ROM. A proportionate split of each sample is used to generate monthly composites for metallurgical analysis utilizing column leaching and bottle roll leaching. These tests are run in a manner analogous with production conditions and deliver test results that provide expected heap leach performance. As the Rochester oxide deposit has been mineralogically and metallurgically consistent, the gold and silver recovery trends have also been consistent over the life of the project."

Sep 1, 2019

By R. K. Will

Granite Construction Company operates a rock quarry in the rugged Santa Cruz Mountains of central California indicated in Figure 1. Open pit methods are used to mine decomposed granite which is processed to produce sand, gravel, decorative rock and asphalt. The quarry is located near the village of Felton about five miles inland from the coast of the Pacific Ocean, and is near the campus of the University of California at Santa Cruz and several California State Parks. The area is heavily forested and is considered by residents to be environmentally sensitive. Because of the scenic beauty of the area and proximity to the San Francisco Bay area, a project such as a quarry receives the attention of regional residents and environmental organizations.

Jan 1, 1994

By K. V. Raj, T. Bhowmick

"The control of fugitive dust in high-latitude openpit mines is challenging due to unique atmospheric phenomena resulting in complicated flow regimes as well as atmospheric inversion due to the lack of adequate insolation during prolonged winter seasons. In this study, two idealized (one conical and one trapezoidal) three-dimensional openpit mine geometries were simulated for different seasonal conditions using a computational-fluid-dynamics package from Software Cradle. The airflow was solved by Reynolds-averaged Navier-Stokes equations using the standard kappa-epsilon turbulence model. The concept of particle tracking was used to predict the flow patterns of dust particles. For various climatic conditions and two different pit geometries, fugitive dust particles varying in size, from PM0.1 to PM10, and concentration were generated at various locations and dispersed by the airflows inside the openpit mine. The amount and location of dust particles inside the pit were reported at various time intervals. In the summer season, airborne dust particles were quickly transported outside the openpit domain. In the winter season, however, the development of atmospheric inversion significantly affected the amount of dust retention inside the openpit domain. IntroductionThe computational-fluid-dynamics (CFD) modeling of openpit mines is challenging. In a recent paper (2015), we presented different constraints and challenges in developing a three-dimensional CFD model. In order to obtain realistic results from a simulation, however, appropriate values of various inputs are required. The simulation results of a three-dimensional nonhydrostatic model by Shi et al. (2000) showed that both the mechanical and thermal forces are important mechanisms, controlling the development of the atmosphere inside an openpit mine. Alvarez et al. (2007) used a CFD model for predicting dust dispersions in a medium-sized limestone quarry, and presented several iso-surfaces of varying dust concentrations using ANSYS CFX. A similar study by Torno et al. (2010) introduced a more sophisticated parameterization of the dust sources. Flores et al. (2014) used an OpenFOAM CFD simulation package to simulate and predict pollutant dispersion in an idealized and an actual openpit mine in Chile with an intense insolation condition. The model was simulated for three different conditions: (1) air-advection (10 m/s, or 33 ft/ sec)-driven mechanical turbulence, (2) surface-heat-flux (240 W/m2, or 76 Btu/ ft2-h)-driven thermal buoyancy and (3) both air-advection- and surfaceheat- flux-driven conditions. The results of the simulations showed that the buoyant currents contribute to the removal of a large percentage of the dust particles. The buoyant currents modify the purely mechanical-turbulence- induced flow pattern and reduce the particle residence time, commonly observed in a purely mechanical turbulent flow (nonbuoyant case)."

Jan 1, 2015

By D. R. Gehring

Effective project management is an excellent technique for meeting a goal through set, well-defined objectives. Even though project management is successfully used throughout the world in various construction projects, underground mining has unique characteristics that require approaches that vary from classical project management theory. Typically, a project includes four main stages: definition, planning, implementation and control. Definition and planning are often the most overlooked stages, but are arguably the most important. This paper addresses practical techniques for the definition and planning of projects for underground construction.

Jan 1, 1996

By B. Kolonja

A SIMAN and CINEMA PC-based simulation model was developed to simulate and animate the truck-shovel operations of surface mines. The model is capable of simulating one mathematical dispatching strategy using linear and dynamic programming and six heuristic dispatching strategies. Data were collected from an actual operating mine through time studies and analysis of historical records. The statistical analyses were performed and appropriate theoretical distributions were fitted for various time events in the truck-shovel work cycle. The model was then applied to study overall impact of these dispatching strategies on constrained and unconstrained mine productivity. The simulation/animation model developed in this study seems to be an efficient planning tool for choosing optimal fleets and finding an &apos;optimal" dispatching strategy to produce an equilibrium between "the quality and quantity of production.

Jan 1, 1993

By Peter M. Fozzard

A review is made of the actual costs of recent foreign mineral exploration programmes in third world countries. Target identification leading to the selection of areas, or macro-targets, must follow a well planned and defined series of steps. Suggestions are made with respect to this inter-active project development work. Potential revenues in the broad sense will always determine the overall economics of exploration but clear objective philosophy, good planning and adequate financing are essential for exploration success. Considerable opportunities exist for making important foreign mineral discoveries and broad selected suggestions are made for the identification of exploration areas in relation to high-grade and precious metal mineralization.

Jan 1, 1984

By R. Jacobson

This paper presents comparison of proposed future solution and in-situ mining methods for in-situ leaching and recovery of uranium, gold, silver, and copper. We propose to show that in the future new extraction methods for each metal will eventually evolve for each hydrometallurgical process step, i.e. in-situ leaching, recovery, and concentration; precipitation and reduction; and drying, when required--without generating waste or bleed streams. In the future, to be highly profitable, these forms of mining will develop into an integrated system to eliminate waste streams using safe, powerful lixiviants. This integration will include, with some exceptions, improvements in the following areas of process development: 1. Lixiviant selection and in-situ leaching technique, 2. Target metal recovery and concentration (at a surface hydrometallurgical facility) from the circulating pregnant lixiviant stream, 3. Target metal precipitation or reduction, where decant water from the precipitate dewatering step is reusable for resin or solvent strip liquor (eluant), 4. Final preparation of target metal for sales, i.e. drying, purification, casting, packaging, 5. Restoration where most of the groundwater restoration process is performed at the same rate as multi-wellfield mining.

Jan 1, 1987