Search Documents

By W. G. Pariseau

A study of coal pillar strength was done at the Beehive Mine during a three year period, 1974?1977, in a cooperative effort involving the University of Utah, RE/SPEC, Inc., and the American Coal Company (Pariseau et al, 1977). The Beehive Mine is located in the Wasatch Plateau coal field in central Utah near Orangeville, Utah, where mines are developed from outcrops between steep canyon walls with topographic relief of a kilometer or so (3,600 ft). Coal is found in Cretaceous sediments that dip gently to the west. Detailed geology of the Wasatch Plateau is described by Doelling (1972). Mining was done in the Blind Canyon seam. An earlier Deseret Mine worked the Hiawatha seam that is lower in the stratigraphic column by about 36 m (120 ft). Mining progress and ownership changes occurred in time with mine mergers and name changes eventually to the collective Des-Bee-Dove label. At the Beehive Mine, depth varied with topography but was approximately 360 m (1200 ft) on average; seam thickness varied from 1.5 to 6 m (5 to 20 ft) and usually required two passes of the miner. The mine was eventually closed and finally reclaimed in 2003. Semborski and Oakley (2006) present a brief history of the mine and describe the reclamation work in some detail. Figure 1 shows the surface topography in the vicinity of the mine that is in the center of the figure.

Feb 23, 2014

By I. WILKOMIRSKY, J. BECKER, F. Parada

Purification of molybdenite concentrate from copper concentrates was performed by sulfation. The sulfation of molybdenite concentrates was carried out with pure sulfuric acid (> 96%) at 160–190 °C to study the influence of the reaction temperature and reaction time on the residual copper in the molybdenite concentrates. A purified concentrate with less than 0.1 wt% copper and low levels of other metals were obtained. For up to 7.1 wt% copper, the conditions required are a temperature of 190 °C, a reaction time of 14 h, and a moly/acid weight ratio of 1/1. Furthermore, several designs of sulfation reactors were evaluated in order to obtain the desired level of copper in the product and to analyze the influence of the operational and design parameters on the reactor dispersion number (Le). The basic design for an 80-t/day plant fed with 4 wt% copper molybdenite concentrate requires five backmixed reactors in series, each measuring 8 m3, operating at 190 °C and with a reaction time of 10 h. The reactor must be protected against severe corrosion by the hot sulfuric acid with either Teflon, glass or ceramic.

Jun 14, 2022

By Dermot M. Ross-Brown

The more important factors controlling the design of pit slopes are related to the local geology over which the designer has little or no control. Nevertheless, there are some factors over which the designer does exert some control and these concern the say in which the rock is excavated and supported. They include blasting, face cleaning, water control, and the use of rock improvement techniques. The paper discusses these factors and relates the extra costs incurred to the steeper slope angles that can usually be obtained. It is demonstrated that even a modest increase in bench angle of 5° through improved excavation techniques can pay off in a single push-back.

Jan 1, 1975

By E. O. Jacobs

A coupled solid and rock fracture mechanics model is used to analyze the blast driven fracture propagation phase, predict propagation rates, and directly measure shockwave and particle velocity. The study incorporates quasi-static pre-stress conditions for different depths below the surface. The scaled experiments include dynamic material properties and quasi-dynamic fracture mechanics which are shown to significantly affect the fracture propagation. The study was performed using three-dimensional cube-type laboratory models fabricated from Polymethylmethacrylate (PMMA). The test cubes are loaded with explosives and resulting fracture networks are studied. The dynamic evaluation of the spatial crack system is monitored using a high speed image camera. An experimental model set-up is designed to indicate the pre-stress effect on deep borehole blasting and is shown that the pre-stress conditions have a decisive influence on fracture profiles and orientation. It is found that shockwaves rapidly exceed the slower dynamic fractures and a majority of cracks occur due to detonation pressure. Experimental testing using different parameters validate that explosive fracturing can predict the outcome of fracture and crack propagation in any rock type with known material properties. This can be accomplished under great stress conditions deep below ground surface. The experimental study results can be applied to a variety of industries such as mining and quarrying, tunneling, oil and gas, and construction.

Feb 23, 2014

By M. Duane Lackey

Electric drives hire done outstanding job in many-fields that are related to the mining industry. The equipment that is offered for electric-trucks was developed from the traction equipment which is used on the diesel electric locomotive. Rotating equipment available for use on electric trucks is identical in principle to that which is used on these locomotives. In as far as it is practical, similar controls are used. Another descendent of the diesel electric locomotive can be found in the oil well drilling industry, Here, locomotive traction motors and. electric controls have been modified to fit the particular requirements of the drilling industry, One 2400 H.P. diesel electric drilling rig drilled a 24,000 Ft. well in West Texas with an electrical maintenance cost in the order of 7¢ per hour This was a new rig and the costs are less than the average maintenance costs will be for the life of the equipment, Even soy since it took one (1) year to drill this well, this 7¢ per hour has real significance. Electric shovels use a similar type of electrical equipment; they too have shown real savings over the equipment they replaced. Since electric drives have done so well, in other fields, they warrant consideration for use in high horsepower, large capacity trucks.

Jan 1, 1961

By Chin Wei Yang

Linear programming (LP) has proven to be a most effective mechanism for modeling a vast array of practical problems, while the development of LP applications in engineering have been extensive enough to show its advantages and limitations. In this paper: we focus on the properties of the widely-wed linear programming transportation (LPT) model formulated and developed by Koopmans (1) . There have been many models of this type applied especially in the field of energy economics (2-7). Since most of these applications can be linked to the seminal work of Henderson (8), we stall present our discussions based on his work.

Jan 1, 1980

By Charles K. Presley

This paper deals with drilling large diameter shafts for the mining and construction industry with diameters in excess of 3 feet to more than 20 feet in diameter. It discusses appropriate applications of the rotary drill method, linings for large diameter shafts, circulation systems,, and the limitations of the method. Each specific rotary drill method is determined by the geology of the area, the depth to be drilled and the formation fluids encountered. Shaft lining or casing must be improved to result in lighter weight, higher strength and lower cost. All phases of rotary drilling equipment must be improved to drill shafts in excess of 10 feet in diameter. As these goals are reached, more shafts of large diameter will be drilled by the rotary method for the mining and construction industry.

Jan 1, 1967

By William J. McCutheon

This paper presents some personal observations obtained during the course of visits to Europe, Africa, Latin America and the United States to talk with senior decision-makers in the copper industry about their views of markets, prices and the future of copper. The industry's future has never been particularly easy to define; with the changes of recent years, prediction has become even more difficult. The author's personal assessments of the present and future are offered for comment.

Jan 1, 1986

By Herbert E. Allen, Andrew F. Kingery, Spyros P. Pavlou

This paper examines and compares the role that chemical speciation plays in the environmental aquatic toxicity of two metals - copper and arsenic. Copper is shown to have well-understood chemical speciation equilibria, but poorly known species toxicities. Arsenic presents the opposite case, with unpredictable speciation in aquatic systems, but is relatively easy to evaluate toxicologically. Speciation is not currently incorporated into Water Quality Standards. This can have a major impact on the cost of environmental containment and cleanup.

Jan 1, 1992

By Dean D. Turner

Exploration geochemistry requires computer processing for quick and efficient reduction and interpretation. An easy to use microcomputer based geologic workstation fulfills this need and allows the geologist to independently process geochemical data. Functions necessary for geochemical data processing are: 1)Digitizing; 2)Communications; 3)Data base management; 4)Statistical analysis; 5)Mapping analysis; and 6)General purpose applications (ie: word processing). A geologic workstation that can perform these tasks will yield significant advantages in processing and interpreting geochemical data.

Jan 1, 1987

By Gary P. Thomason

We have all heard a great deal about how various projects were financed or certain companies were successful in obtaining a bank loan. There are many more projects and companies who fail to get the money they need. At least a portion of these failures, and a large percentage of the frustrations connected with even the successful financings, are a result of not understanding the process of obtaining money. Recent years have seen a proliferation of sources available to finance minerals operations, but let me assure you that these represent only a minor portion of the minerals financing market. The fundamental source of borrowed money to almost all minerals related companies remains the banks. Therefore, understanding the "Loan Approval Process" can easily mean the difference between getting the money or not. In the following pages I hope to provide some insight into what I define as the loan approval process. Having pre-offered my definition, I intend to delineate the various stages of the process and the planning and information I believe should be contained in each. My ultimate goal is to help you think like a banker and, in so doing, stay on top of the process so that you can successfully obtain the funding necessary for your projects.

Jan 1, 1983

By Ralph T. Buscarello

For practical purposes, the terms "natural frequency," "resonance" and "critical speed" are synonymous. A part passing though its "critical" or "critical speed" may also be said to be "resonant" or "resonating." The vibrations of a precisely balanced part can be magnified by the structure in which it is assembled. Anyone who has driven an automobile knows that it will vibrate more at a certain speed than at others. According to the formula for centrifugal force, vibration should increase steadily with a rise in rpm. What happens instead is that the vibration not only in- creases with r m. but suddenly rises at a much higher rate through the critical speed, and then apparently smooths out as the rpm passes beyond it. To visualize what happens, consider a simple flat spring with a weight mounted at one end. When the spring is deflected by pulling down on the weight and then letting it go, the spring will oscillate, and the spring-and-weight system will vibrate at its natural frequency. If the timing or direction bf the impulses imparted to the spring did not coincide with its natural frequency, the result would be an irregular vibration that would not build up. If, on the other hand, the timing and direction of the impulses did coincide with the spring's natural frequency, the result would be a larger and larger amplitude. If the impulses were continued indefinitely, the amplitude of the spring's vibrations would go on rising [while its frequency stayed the same] until the spring broke or the amplitude of the vibrations reached an equilibrium [because frictional or other forces would tend to damp it]. Resonance magnifies the amplitude of vibrations in a relatively undamped system between 100 to 200 times over that of nonresonant vibrations. Frictional or viscous damping often reduces the magnification [from 10 to 20 times], but even with this reduction the amplitude would still be large enough to cause excessive wear, and sometimes even fractures. For example, a blower might show only 0.001 in. of vibration on the manufacturer's test stand. Installed, the blower could pass into its critical speed [the speed at which the frequency of the vibrations caused by the rotor coincides with the supporting structure's natural frequency], and the 0.001 in. of vibration could be resonated to 0.010 in., or as much as 0.020 in. The cure for such a condition would not be to lower the vibration of the blower by further balancing or better alignment but to separate the two frequencies by at least 20 to 30%.

Jan 1, 1970

By J. Schoenbacher

Park City Municipal Corporation (PCMC), long before being recognized as an Olympic venue was known as one of the great American silver mining towns. During a century of active mining, the Park City mining district produced millions of ounces of silver in addition to a substantial amount of mine tailing waste. Since 1985 the City has been remediating these impacts with state and federal oversight. One particular challenging CERCLIS site, that was previously a historic mine tailings pond is known as Prospector Square Development (CERCLIS Listing Silver Creek Tailings UTD98051404). This site has been very challenging due to the metals that impact the shallow ground water that eventually drain into the Silver Creek Watershed. To address the water quality impairment the City and Missouri University of Science and Technology teamed up to investigate the feasibility of constructing a horizontal-flow wetland to treat this pollutant source. This effort began with the building of a pilot cell in June of 2004 and lead to the construction of a full scale horizontal-flow wetland in the fall of 2008. The design of the pilot and full scale biocell was based upon lab-scale research conducted by the Missouri University of Science and Technology. In October of 2008, the Prospector Drain effluent was introduced to the system and to date analytical results reveal that the biocell is treating the Prospector Drain outfall below the Silver Creek Total Maximum Daily Load (TMDL) endpoint goals for zinc .39 mg/L and cadmium .00075 mg/L. The water chemistry of the influent, that originates from the historic silver mine tailings pond, is impaired with zinc and cadmium and has low iron with a pH of roughly 6.5. The construction of this unit encountered many challenges related to constituent relations, regulatory scrutiny, constructability and start-up. Nonetheless, since implementation this unit is considered a success for improving water quality within the Silver Creek Watershed.

Jan 1, 2011

By M. W. Harmer

Laboratory test work, pilot plant testing and plant experience with wet, fine mesh screens is discussed. High frequency, low amplitude, fine mesh, wet screens were installed on the 6th cleaner concentrate stream. These screens produce a 60% oversize recovery split of the molybdenite concentrate that is of leached equivalent quality. The undersize stream is leached with 'hot ferric chloride to remove Pb and Cu contaminates before roasting or shipment to sulfide customers. This plant modification is a good example of using existing technology in an unconventional flow sheet to yield significant cost savings.

Jan 1, 1990

By G. R. Addie

While the cost of transporting raw phosphate matrix from a pit to a processing plant via slurry pipelines is more efficient than it could be by rail cars, conventional trucks or belt conveyors, it still amounts to many millions of dollars, and in many areas there still exists much room for improvement. By taking advantage of pipeline test data on different slurries, it is possible to reduce costs by optimizing pipeline diameters, operating velocities and slurry concentrations. Better wearing, more efficient pump designs are now available which, if applied correctly, can lead to significant savings. The authors discuss what benefits are possible in relation to the electrical operating and wear maintenance costs and go into some of the factors associated with taking advantage of these benefits, identifying what they see as being practically possible.

Jan 1, 1998

By C. Sun

With complex component, higher salt content, low biodegradability, DSD acid oxidation wastewater could not be efficiently dealt with traditional methods. It is pointed that the coal water slurry could be made with DSD acid oxidation wastewater of different concentration and the density of coal water slurry could be up to 70%, while its viscosity is only 850~930 mPa?s. The coal water slurry could be perfectly jetted and burnt under different conditions. The higher density the DSD acid oxidation wastewater has, the better properties the coal water slurry have. The pollution components and characteristic group of DSD acid oxidation wastewater are similar to the additives of coal water slurry, so it could be used as a kind of usable additive of water coal slurry. It is so reasonable and feasible to make coal water slurry with DSD acid oxidation wastewater that the pollution of DSD acid oxidation wastewater can be solved completely.

Feb 23, 2014

By S. Aktas

The present work describes an investigation of a hydrometallurgical process for the recovery of mercury from spent silver oxide button cells. The cell paste was leached in nitric acid to solubilize silver, mercury and zinc. The optimum leaching conditions, in which mercury is entirely converted to Hg2+ ions and, therefore, does not coprecipitate with silver chloride during treatment with potassium chloride solution, were 1.0 M HNO3, 45° C, 1 hour and 200 rpm. After the silver was removed from the solution, mercury was cemented out with zinc powder with an efficiency greater than 99%. In the cementation experiments, the amount of zinc powder, shaking rate, temperature and solution pH were investigated in detail. The mercury recovery (%) increased as the amounts of zinc powder and the temperature were increased. Zinc hydroxide was precipitated from the waste solution by the addition of sodium hydroxide. The Zn(OH)2 precipitate was then converted to zinc oxide. The proposed process is proven to be simple, straightforward and environmentally friendly.

Nov 1, 2011

By S. Aktas

The present work describes an investigation of a hydrometallurgical process for the recovery of mercury from spent silver oxide button cells. The cell paste was leached in nitric acid to solubilize silver, mercury and zinc. The optimum leaching conditions, in which mercury is entirely converted to Hg2+ ions and, therefore, does not co-precipitate with silver chloride during treatment with potassium chloride solution, were 1.0 M HNO3, 45° C, 1 hour and 200 rpm. After the silver was removed from the solution, mercury was cemented out with zinc powder with an efficiency greater than 99%. In the cementation experiments, the amount of zinc powder, shaking rate, temperature and solution pH were investigated in detail. The mercury recovery (%) increased as the amounts of zinc powder and the temperature were increased. Zinc hydroxide was precipitated from the waste solution by the addition of sodium hydroxide. The Zn(OH)2 precipitate was then converted to zinc oxide. The proposed process is proven to be simple, straightforward and environmentally friendly.

Jan 1, 2011

By Fabian Laumen, Sunny Schoone, Felix Leaman, ELISABETH CLAUSEN

The acoustic emission (AE) technology has a high potential for flow characterization in hydraulic transport processes. For instance, in deep-sea mining, there are applications where manganese nodules are transported from the bottom of the sea to the surface or a transport ship. Here, an AE-based flow characterization system plays an important role to avoid the transport of non-related objects. However, the structural materials for the components of this system must be carefully selected to ensure resistance against corrosion and a good AE signal transmission. Therefore, in this experimental study, we evaluated the AE attenuation behavior of four different materials that can be employed in marine environments due to their properties. The results were obtained using thin plates and they indicate which materials have the highest and lowest attenuations. Moreover, we provide insights regarding the different wave modes that propagate on the plates.

Mar 2, 2023

By Richard L. Bullock

At the beginning of the previous chapter, variation in the types of room-and-pillar stopes were briefly identified so that the reader could begin to understand the extensive application of this mining system. These same variations will be reviewed and elaborated upon in this chapter while discussing the methods by which the material is extracted. FULL-FACE SLICING BY DRILLING AND BLASTING When the entire mineralized thickness is taken in one pass of mining, it is known as full-face slicing. There is no mineral of economic value intentionally left either in the floor or the back. Theoretically, there is no limit as to how high the face could be in a single pass. But there are practical limitations to equipment size, pillar stability, and control of local loose slabs on the face, roof, and pillars that dictate current practices. The range of face height of the 15 typical room- and-pillar mines covered in Table 8 (Sec. 1, Subsec. 7) from the Dravo report, 1974 was 1.7 m (5.5 ft) to 9.8 m (32.1 ft), the average being 5.2 m (17.1 ft). In the Gaspe copper mine, Murduchville, Que., the drill jumbos were constructed with an extendable tower for full-face mining up to 15.2 m (49.9 ft) if necessary. However, a more common practice at that mine is to take the ore in multiple slices (Hall, 1959). In many metal mines the normal practice when starting stoping is to drive a single development drift into the ore zone a distance that will allow at least four or five rooms to be opened on each side of the initial drift. Since this opening will probably serve as the main haulage drift, it should be kept as straight and as level as possible. As to the other criteria for the stope developments, it might be well at this point for the mine planner to review the remarks presented earlier (Sec. 1, Subsec. 7) on drifts, entries, and crosscuts for production. After the initial drift is driven, it should be slabbed to the full room width if it is not that wide already. Next, the future pillars should be marked on the ribs and the rooms driven between them. If the ore extends beyond the length of the initial drift and is to be mined in the normal sequence of mining, care should be taken in a random room-and-pillar system to see that the extension of the initial roadway remains straight. If pillar "spotting" is left to the shift foreman or to the miners, they probably will not realize the importance of maintaining a uniform pillar line next to the roadway, and of keeping the line straight. Invariably, a pillar will end up in the middle of the future drift extension resulting in a "dogleg" in a possible main haul- age road. While this error is not catastrophic, too much weaving in and out of pillars will certainly slow down future production haulage and needlessly increase costs. Face or Breast Drilling and Blasting Practices To drill and blast the initial advances into the rock, usually some form of cut pattern must be used. In room-and-pillar mining, when a pattern is drilled in a face and that face is the only exposed surface to which all of the rock must be broken, the pattern is known as a "face round" or "swing." The face to which the rock must be broken is referred to as a "free face." Thus the most common way to advance a room into virgin rock with only one free face is by drilling swings. If, after breaking around a pillar, taking down back, or taking up bottom, there is a second (or third) face exposed, a group of holes drilled nearly parallel to a free face and breaking to it is known as a "slab round" or "slabbing." In some mining districts it is also known as "slashing." Obviously, because two faces exposed offer less resistance to fragmentation than a single face, slabbing requires less drilling and fewer explosives than required to break the same tonnage with the same degree of fragmentation with swings. Therefore, it behooves the driller (or supervisor) to plan the combination of

Jan 1, 1982