Search Documents

By David M. Lake

Conversion to trolley assist is a means of minimizing diesel fuel consumption, which in many mining situations offers a rapid payback of capital investment plus the inherent flexibility and maneuverability of truck shovel operation. When diesel electric truck shovel mining operation with trolley assist is compared to alternative mining methods such as conveyor systems, the trolley assist system can be easily justified in terms of return on investment, payback and increased productivity. A review of present technology, performance requirements and past experience in the mining industry has led to the development of a trolley assist system for diesel electric haulage trucks which, is proven in the mining environment, offers significant reduction in fuel consumption and increased productivity.

Jan 1, 1981

By R. Duckett, D. Salisbury, R. Dorey

The Kennecott Ridgeway Mine in South Carolina is scheduled to complete mining and ore processing in the last quarter of 1999. Tailings are disposed in a 300 acre, lined tailings impoundment. To facilitate closure and reclamation, modification of the tailings impoundment operation has been adopted. Mining involved the sequenced development of two open pits. In 1996 mining of the South Pit was completed and backfilling of the pit with waste rock from the North Pit was initiated and will continue until mining ceases. Both pits will be reclaimed as fresh water lakes. This paper presents the physical, geochemical and hydrogeochemical evaluation of the operational and post operational management of the project. Comparison of the operational monitoring data against predicted performance are reviewed.

Jan 1, 1999

By M. R. Shahan, C. E. Seaman, Mischler S. E., T. W. Beck

"Float dust deposits in coal mine return airways pose a risk in the event of a methane ignition. Controlling airborne dust prior to deposition in the return would make current rock dusting practices more effective and reduce the risk of coal-dust-fueled explosions. The goal of this U.S. National Institute for Occupational Safety and Health study is to determine the potential of open-air water sprays to reduce concentrations of airborne float coal dust, smaller than 75 µm in diameter, in longwall face airstreams. This study evaluated unconfined water sprays in a featureless tunnel ventilated at a typical longwall face velocity of 3.6 m/s (700 fpm). Experiments were conducted for two nozzle orientations and two water pressures for hollow cone, full cone, flat fan, air atomizing and hydraulic atomizing spray nozzles. Gravimetric samples show that airborne float dust removal efficiencies averaged 19.6 percent for all sprays under all conditions. The results indicate that the preferred spray nozzle should be operated at high fluid pressures to produce smaller droplets and move more air. These findings agree with past respirable dust control research, providing guidance on spray selection and spray array design in ongoing efforts to control airborne float dust over the entire longwall ventilated opening. IntroductionCoal mining processes produce airborne dust that naturally deposits on the floor, roof and ribs of mine airways. These fine dust particles, termed float coal dust when smaller than 75 µm in diameter, are deposited in the return entries of coal mines and can be reentrained by pressure waves induced by methane-air explosions (Rice et al., 1911; Nagy, 1981; U.S. National Institute for Occupational Safety and Health (NIOSH), 2006). These particles are also those most likely to participate in coal-dust-fueled explosions, which can potentiate and propagate explosions resulting in extensive damage. In order to meet compliance requirements of at least 80 percent incombustible content in the composition of material deposited in mine entries (U.S. Mine Safety and Health Administration (MSHA), 2016), coal mines apply an inerting agent, specifically, rock dust (Harris et al., 2009). Should methane be present in the mine atmosphere, the required fraction of incombustible content is further increased by 0.4 percent for each 0.1 percent methane. The removal of airborne float coal dust (AFCD) prior to deposition is an approach intended to make current rock dusting practices more effective by increasing the proportion of inert material to combustible material, resulting in a lower risk of coal-dust-fueled explosions."

Jan 1, 2018

By Thomas D. Boyce

Minewater from many western U.S. uranium mines often contains radioisotopes in concentrations higher than permissible for discharge to unrestricted areas. .Radium 226 has the lowest permissible concentrations of all radioisotopes and usually greatly exceeds this limit in untreated effluents. This radionuclide is derived from the natural radioactive decay of uranium: [ ] The treating of minewater effluents has been studied previously (1) and the classical removal method for radium has been adsorption on barytes or freshly precipitated barium sulfate. This paper describes the removal of radium from minewater by utilizing a selective complexer based on a crosslinked organic polymer matrix.

Jan 1, 1982

When a company like Lonmin, the third largest platinum producer in the world, is mining one of the most precious metals in the world, time is money. Every piece of equipment is expected to be in top shape because every minute of downtime can add up to lost profit. Two different types of platinum ore are mined and processed by Lonmin, namely Merensky and UG2. Merensky has a grade of 3.5 g/t (0.1 oz/st) and UG2 has a grade of 4.5 g/t (0.13 oz/st). The mine also produces platinum group metals (PGM), which consist of platinum, osmium, palladium, rhodium, iridium and ruthenium. Although South Africa has more than 80 percent of the world?s PGM reserves, these minerals are very scarce. Lonmin is considered a low-cost producer of these minerals, generating 21.5 t (694,000 oz) of platinum and 18.6 t (600,000 oz) of PGMs in 2012. So when the company?s Karee K3 concentrator plant in Rustenburg, North West Province, South Africa, was experiencing high operating costs on the transfer points, a solution was needed.

Jan 1, 2012

By Zibo An, Yong Hu, Hao Zhang, Hong Cao, Jun Xue, Zhen Luo

Phosphogypsum (PG) is a by-product of solid waste produced by the phosphate chemical industry. Owing to large emissions and massive storage issues, it causes a potential threat to our environment. Hereby, a method based on the precipitation and crystallization properties of calcium phosphate-magnesium ammonium phosphate (CP-MAP) followed by its adsorption on active solid waste powder is used as the main principle to treat PG harmlessly. The treatment process and its influencing factors for orthogonal experiments along with the associated environmental safety have been studied in detail. The results showed that this method could simultaneously remove soluble phosphorus and soluble fluorine from PG. When ACP, FA, HBM, and Ur were added to PG at a dosage of 3%, 13.5%, 0.04%, and 0.04%, respectively, the residual phosphate and fluoride contents was 0.061 mg/L and 0.856 mg/L respectively in the PG leaching solution. Compared to state-of-the-art approaches, this method exhibited higher efficiency in removing phosphate and fluoride. Most importantly, this method does not cause any secondary pollution in the process, thereby showing a novel application in large-scale industrial treatment.

Aug 29, 2022

By Simón Díaz-Quezada, HUMBERTO ESTAY

The heap leaching process has been widely used for recovering different metals since its first application at the end of the 1960s. In Chile, copper production via heap leaching has accounted for between 30 and 40% of annual copper production over the past 10 years. This level of production has been achieved through and supported by the use of a mathematical relation, known as the leaching ratio (LR) or irrigation ratio (IR), which relates operational parameters with metal extraction in a heap leaching operation. This ratio has been used to develop leaching column tests, to scale up results from the laboratory to industrial operations, to design new heap leaching plants, and in metallurgical control and production estimation. In spite of the widespread industrial use of this relation, few scientific studies mention it. This is due to its simplicity and basic theoretical foundations. This disparity between industrial practice and scientific research could lead to operational decisions which lack substantial theoretical support, and to scientific studies which have limited industrial impact. Against this background, several questions arise about the use of the LR: What are the constraints on the use of the LR? Are there practical advantages with respect to reported kinetic models? What is the main reason that industry prefers the use of the LR over kinetic models, which enjoy greater theoretical support? In order to guide its future use, this paper describes the leaching ratio and its current uses and limitations, through a literature review and case studies.

May 2, 2020

By Paloma Lazaro, Moe Momayez

Interactions between human beings and their work environment require the body to regulate its temperature by balancing heat production and loss. Comfortable environmental conditions are crucial for keeping workers safe and healthy and to maintain a suitable level of productivity. However, achieving a proper core body temperature may become challenging under different conditions, especially in high heat-generating workplaces such as hot underground mines. Because hot underground mines have the potential to expose workers to heat stress, compliance with standardized and regulated indices and criteria is distinctly required. The objective of this paper is to provide an overview of the current research on heat stress and strain in hot underground mines, collected from published and specialized literature. General definitions, statistics of heat-related accidents in mining, overview of the indices, standards, and recommendations for heat stress are provided herein.

Oct 6, 2020

By Dongjie Zhang, Shuxin Liu, Jianduo Wang

Broken rock mass and unreasonable stope structure parameters can cause excessive ore loss and dilution in sublevel caving; this is the main problem faced by caving mining in recent years. This paper proposes a stope structure parameter optimization method suitable for steeply inclined medium-thick broken ore bodies and evaluates the reliability and effectiveness through case studies. To solve the problem of large ore loss and dilution in the high-end wall sublevel caving method of Xilinhot fluorite mine, it is necessary to select proper stope structure parameters. Based on the theory of random media, an end-wall ore drawing experiment was carried out, and the bulk flow parameters needed to optimization of stope structure parameters were determined. In the experiment, it was found the draw-out body of high-end wall ore drawing showed a fine top and a thick bottom; the granular media had good fluidity. The reasonable caving step is determined to be 1.2 m instead of the 1.6 m originally used. Through the optimization experiment of the mining route position along the vein, the study found that the best route position is different with the ore body inclination. When the inclination angle of the ore body was 90°, the reasonable route was located in the center of the ore body. When the inclination angle of the ore body was between 85° and 90°, the route moved from the center of the ore body to the footwall at a rate of 22.5%. When the inclination angle of the ore body was between 80° and 85°, the route moved to the footwall at a rate of 54.8%. When the inclination angle of the ore body is not greater than 80°, the route should be arranged on the boundary of the footwall. Field application results showed the dilution rate reduced by 7.66% and the recovery rate increased by 7.31%. Field test results verify the effectiveness and applicability of the optimized stope structure, which corroborates the effectiveness and applicability of the optimized stope structure.

Mar 10, 2022

By Walter H. Schwedes

Ore grinding mills are really just slowly rotating barrels, but barrels that are growing in size so fast that the application of electric drives for them is rapidly approaching a technology like that for wind tunnels or pumped storage drives. This application is particularly worthy of care because some 40% of the 75 megawatts of power used by a large copper ore concentrator, or some 60% of the 200 megawatts supplied to a large iron ore concentrator, are for grinding. These ore plants are located where the ore is, not where a utility happens to be. So, the challenge is not only to choose a drive and .power transmission for reasonable cost, high performance, reliability and minimum maintenance, but to afford the interface between mill drive and power distribution and source systems to minimize the whole ore plant's monthly power bill, or costs of self generation. Conclusions can be reached in optimizing a drive selection only for each particular ore plant's set of parameters, but by identifying the criteria for selection and then weighting each type of drive per criteria, yardsticks for final choice become apparent. This is the purpose of this paper. Grinding action takes place inside the barrel, where the ore charge is ground with the aid of balls, or mill length rods, or large chunks of ore as in autogenous grinding.

Jan 1, 1972

By J. G. Groppo

A beneficiation process has been developed to provide selective separation of unburned carbon from high loss-of-ignition (LOI)fly ash. Using froth flotation to achieve selective separations requires long residence times and high reagent costs. A proprietary reagent system has been developed to address these limitations. Based on the results obtained from laboratory and pilot-scale investigations, a flowsheet design has been developed to produce two distinct usable products from class F fly ash — low LOI ash and a high-carbon product suit-able for reburning or further upgrading.

Jan 1, 1996

By Sadegh Elyasi

TBMand roadheader are two dominating excavation machines in underground tunnelling projects. The performance of these two tunnelling machines has been reviewed and analysed individually by many researchers from multiple points of view. However, there are almost no studies that have made an extensive comparison between these two machines, mostly from financial points of view. The current study is intended to characterize both financial and technical status of these two mechanical tunnelling machines in one of the biggest coal mines in Iran. The main objective of this study is to define the best method and equipment that meets a predefined economic goal, which is mainly to maximize the net present value. To this end, a technical and financial model based on the geomechanical and financial parameters involved in the project has been prepared and the financial part of the project has been carried out by applying COMFAR III financial analysis software. Subsequently, a sensitivity analysis of the model was conducted in order to evaluate the effect of involved parameters on the project. According to the results, a roadheader has better economic justification than a TBM, while the TBM has a better advance rate than the roadheader.

Feb 12, 2021

By Immo H. Redeker

Introduction In October of 1961 Texas Gulf Sulphur Company contacted the Asheville Minerals Research Laboratory, of the North Carolina State University, and requested assistance in the development of a phosphate ore body in Beaufort County. The main: objectives of the work at Asheville were defined as follows. The Laboratory should try to determine on the basis of drill core samples, submitted by Texas Gulf Sulphur Company, the highest grade of phosphate concentrate that could be obtained with high recoveries from North Carolina ore, the thickness of the ore body that could be treated economically in one section, and the quantity of concentrate that could be obtained per acre. The results should be compared with data obtained from the treatment of Florida ores. It was important to use mineral preparation methods during the initial laboratory work that could be verified later by continuous pilot plant operation and could be scaled-up for a commercial plant. The writer was in charge of the project at the Asheville Minerals Research Laboratory and participated in the development of one of North Carolina's greatest mineral resources from the first drill core examination to the production of the first poundage and tonnage quantities of flotation concentrates. The Lee Creek phosphate mine and mill was put in operation in early 1966 and can produce three million tons of phosphate concentrate a year. Sulfuric- acid, and phosphoric acid plant, diamonium phosphate plant and triple super phosphate plants came on stream in 1967; at that time they were the world's largest. Now that a phosphate industry has been established in the State, it]

Jan 1, 1971

By M. Kuchta, S. Iverson

INTRODUCTION Underground blasting with perimeter damage control can reduce the requirement for loose rock scaling and reduce the risk of ground-fall injury. In previous work Johnson and associates (2010) from the National Institute for Occupational Safety and Health (NIOSH) developed a rock blasting perimeter damage and control design method included in the DRIFT software tool (NIOSH, 2018). This blast design software tool utilizes current methods of perimeter blasting with the added design element of a buffer row coordinated with the perimeter row to reduce perimeter damage. The coordination is in applying one of several blast damage models to calculate the damage extent for each production, buffer, and perimeter blast hole in the design. The calculated damage is then applied to the spacing between the blast holes. The basis of the buffer row design is the practical damage limit and is supported in this paper with computer models of signature blasts and full blast rounds using PFC2D (Itasca Consulting Group, Inc., 2018). Practical damage limit The practical damage radius (Rd) is not to be confused with burden. The practical damage extends toward the burden side and inward into the rock mass. For all practical purposes, the practical damage radius equals one half the burden (Hustrulid, 1999). The maximum extent of radial crack damage around a blast hole (Rcrack) and the maximum extent of radial crushing damage (Rcrush) are illustrated in Figure 1. A “practical” radius of damage (Rd) lies between the crushing limit and the cracking limit. The “practical” damage means that if the rock mass lying outside of the practical damage circle were removed, the rock remaining within the circle would easily break apart. Blast pressure and strain Work by Johnson (2010) and associates included signature blast tests in large concrete blocks. A signature blast test in concrete as exampled by strain data in Figure 2 was designed to monitor the dynamic strain at incremental distances from a single fully coupled blast hole, measure crushing and radial cracking extent by wire-sawing to expose the damage, and relate the damage to overbreak that is common in underground blasting. The initial slope or rising strain as the stress wave passes by the strain gages shows very high strain and strain rates close to the single blast hole. Since the derivative of strain versus time is strain rate, a line tangent to each of the strain curves at the maximum strain rate is drawn and the strain rates identified. The high strain rates were then plotted on a semi-log in Figure 3 to show a linear trend. The strain rate is greater than 100 s-1 within 20 cm from the blast hole for the signature blast experiment. The strain rate at the blast hole wall is projected to be 300 s-1. Figure 4 illustrates the damage in the NIOSH block exposed by a wire saw cut.

Jan 1, 2019

By M. Girardeau, J. Blondin, M. Nomine

It is well known that surface moisture and fine content have a strong influence on coal handle- ability. It is known as well that these two criteria are not sufficient to classify coals. It seems that certain types of coals are intrinsically difficult to handle, the reason being still not well understood. For these coals, moisture and fine content are aggravating factors and have to be strictly controlled in order to avoid handling problems (sticking, arching in hoppers.. .). CERCHAR has undertaken research aimed at identifying the role of intrinsic characteristics of coal with regard to handling properties. Two of them have been identified as particularly relevant : the clay content and the "colloidal particle" content. Two simple tests commonly used for soils characterisation, but never used so far for coal, have been applied to characterise a wide range of coals. The derived classification has been compared with an empirical classification based on dry screening tests. DRY SCREENING EXPERIMENTS Dry screening at a relatively low screen aperture (e.g. 6 mm) may be considered as a good tool for assessing the handleability of wet fine coals. Difficult to handle coals always lead to rapid plugging of the screen whilst easy to handle coals can be screened without difficulties. A wide range of coals has been selected with various ash, moisture and fine content. Their characteristics are given in table 1. The experimental set-up consists of a 2 t.p.h vibrating screen equipped with two automatic re- cording balances collecting respectively oversize and undersize material. Provided that the feeding rate is accurately controlled, good reproducibility in the percentage passing as a function of time is obtained. Figure 1 gives examples of different types of relations that were obtained. - LMC coal exhibits a behaviour that is characteristic of easy to handle coals : % passing remains constant in the course of the screening operation. - B coal behaves slightly differently. One observe first a rapid decrease in the flow passing through the screen and then a stabilization. Hand- ling properties can be considered as intermediately - The curve relative to LHB coal is characteristic of a very difficult to handle coal that blinds the screen almost immediately. It is necessary to point out the fact that the classification derived from screening experiments is a global one, including not only intrinsic factors but also external factors such as fines and moisture content. The role of surface moisture is in particular very important and variations in this parameter may upset the empirical classification

Jan 1, 1988

By Alexander N. Winchell

"Location. The copper mines of Michigan are all in the northern part of that state on the Keweenaw Peninsula, which extends from the (Michigan) mainland for about seventy miles northeasterly toward the middle of Lake Superior. The mines occur in a belt or zone occupying the central portion of the peninsula from end to end.. The most productive mines for many years past have been those located not far from the city of Houghton in' the central part of the zone, in a section extending about ten miles southwest of Houghton and fifteen miles northeast. The most important mines in order of location, from the northeast to south¬west, are the following: Mohawk, Ahmeek, Allouez, North Kearsarge, Wolverine, South Kearsarge, Centennial, Calumet. and Hecla, Osceola, Franklin, Quincy, Hancock, Isle Royale, Superior, Baltic, Trimountain, and Champion. The first three named are in Keweenaw county and all of the others are in Houghton county. Still farther to the southwest are the Lake, Mass, Adventure, Michigan, Victoria, and White Pine mines. These are in Ontonagon county.History. The exploitation of these copper mines extends back into prehistoric times. There is little evidence that the American Indians carried on mining operations in this region in the period shortly before the advent of white men, but there is abundant evidence that the ancestors of the Indians, •or some earlier inhabitants of the region, carried on primitive mining operations. For example, Mr. S. O. Knapp, Agent of the Minne¬sota Mining Company, in the winter of 1847-48, made the first discovery of prehistoric mining. This event is described as follows by Foster and Whitney :"

Jan 1, 1920

By R. L. Loofbourow

Reasons for reexamining underground mining include: 1. The assurance that more deep deposits of useful minerals will be found. 2. The existence of deeply covered deposits of industrial minerals near large markets where quarries are becoming depleted or are lacking. 3. Surface property values, zoning and other limitations on open pit mining. 4. Expectation that underground space will be increasingly used for transportation, power plants, storage and similar purposes. 5. The improvements which have been made in underground mining. During the last three or four decades many changes and improvements have been made underground. All underground construction and mining has benefitted to some extent but the effect on the productivity of labor employed with some methods- has changed little and the use of these methods has declined. Productivity of labor in other methods has increased substantially. The relative usefulness of mining methods has changed and a vital industry, bituminous coal, has been returned to health. In this paper, consideration is limited to nine methods used with high productivity during the period under review. These methods are not necessarily better than others but they may be considered the prime methods in the sense that, in our economy, many, low grade ores, coal and the principal industrial minerals could hardly be produced by less productive means.2 Although most of the examples cited are from mining as such., the first four methods discussed can be used for the construction of stable excavations of various' shapes in sound rock.

Jan 1, 1967

By William C. Peters

The frustration encountered by exploration crews in connection with land acquisition could be graphed to show a correlation with the natural law that everything tends to become more so. Figure I shows a rather common, situation. The combinations of ingredients are almost limitless and the resulting brew is often poisonous to an exploration man. A single step, that of taking a series of deep soil samples is often delayed until some sense can be made from "floating" unpatented claims which are obscure in orientation as well as position, placer claims overlapping lode claims, location posts with empty Prince Albert cans, and claims with no apparent assessment work for ten years. Add to this some patented claims with¬out monuments, a state or federal withdrawal area which may or may not invalidate pre-existing claims, a loosely defined tunnel site, and some ranchers who understandably resent the separation of surface rights from mineral rights. The picture is familiar to exploration men. One approach to such problems is to ignore them until someone voices an objection -- but then an even more chaotic situation is likely to develop. Another practice is to stake new claims to cover all ground that is "open" at first glance and then find out if there are conflicts so that the new claims can be adjusted accordingly.

Jan 1, 1970

By Bernie W. Martin, Raymond Leray, Christian Criado

Aguas Argentinas,1 a consortium managed by Lyonnaise des Eaux of France and operator of the world’s biggest privatized water supply and waste water collection system for the City of Buenos Aires, a city of 9 million people, was faced with the daunting task of providing new service to 1.6 million more people in the first five years of their 30 year concession. Aguas Argentinas elected to use the Negotiated Compressed Process - NCP - for the fast track implementation of a 15000 meter, 3,5 meter diameter tunnel, a key component of the infrastructure master plan. NCP was developed by Klohn Crippen for the $200 million international railway tunnel between Canada and the United States. The conceptual design of the project was performed by Safege Montgomery-Watson, who engaged Klohn Crippento assist with the NCP, the preparation of the tender documents, and implementation of theproject during construction. The process included the purchase by the client Aguas Argentinas of two sophisticated 4 metre diameter earth pressure balance tunnel boring machines from Herrenknecht of Germany. Construction of the tunnel is being performed by the consortium Wayss & Freytag (Germany) and Sollazzo Hnos S.A. (Argentina). The water tunnel is being built with a one pass, bolted segmented gasketed reinforced concrete liner. The purpose of this paper is to describe a transferable methodology for this innovative contracting procedure, the project organization and quality control plan for this important world class tunnel project which is designed to service one of Latin America’s largest metropolitan areas.

Jan 1, 1997

By C. E. Golson

Modern concrete technology emphasizes the basic qualities required of an acceptable aggregate: it must be clean, sound, homogeneous, and of a size gradation resulting in a concrete of the desired physical qualities at a minimum cost. In the case of coarse aggregates, crushing, scrubbing, and screening will usually provide the required material, although beneficiation is often necessary in order to eliminate unsound or deleterious fractions. Beneficiation is also applicable to fine aggregates,( but the processes most often employed are washing, classification, and dewatering.

Jan 1, 1959