Search Documents

By Peter K. Mathison

The U. S. Department of Interior, Bureau of Mines (Bureau) is developing a hydrologic monitoring system for in situ leaching operations. A working prototype of this system was installed and tested at the Cyprus Casa Grande copper mine. Requirements specific to in situ leaching operations were identified by researchers. The system has been a useful tool for researchers and for mine personnel. Observations of the hydrologic monitoring system, including details of the development process, the design of the system, and the software developed at the Bureau have resulted in new ideas for an enhanced design of the system.

Jan 1, 1992

By M. Mead, J. Dumouchel, W. Yule, J. Giroux

The QMM mineral sands of South East Madagascar contain approximately 1,900 million tonnes of mineable sand with a total heavy mineral (THM) content of roughly 4.5wt%. The QMM deposits are the world’s largest known reserves of 60% TiO2 ilmenite and also contain a small volume of zircon. The deposits are semi-continuous and homogenous and the mineralized sands are free flowing with minimal overburden, induration & slimes. These characteristics are favourable to dredge mining and allow the application of conventional wet gravity, electrostatic & magnetic separation to final products. A mature THM mineral suite of high valuable heavy minerals (VHM) content has enabled the development of a relatively simple separation process.

Jan 1, 2005

By C. P. Mangelsdorf

Introduction The use of frequency of vibration measurements to determine tension has long been accepted by industries that use electrical or stranded cables of wire ropes in their operations. In contemplating how to determine the tension in chords of a roof truss, it seems almost inevitable that a similar approach should be investigated even though there are some important dissimilarities in physical behavior between a chord of a rod-type Birmingham truss and a stretched wire rope. While the dominant feature of both types of behavior is the existence of tension, the bending resistance of the vibrating truss chord cannot be ignored. And it is common to have attached to the chord, pieces of hardware (turnbuckles, extension sleeves, wedge boxes) that represent concentrations of mass not usually found in a vibrating wire rope. Analytical solutions to the problem of vibrating wires or beams can be found in the literature on vibrations (Timoshensko, 1955; Den Hartog, 1956). But in every case, at least one of the ingredients of the vibrating truss chord is missing. The presence of axial tension, or bending resistance, of concentrated masses and of end conditions peculiar to truss chords is a combination that appears not to have been dealt with before, although the techniques for dealing with it are commonly known. The purpose of this note is to report the results of a project to measure and calibrate such frequencies. The work was conducted by the University of Pittsburgh under the sponsorship of the US Bureau of Mines. Field observations Tests were conducted on 24 different truss installations. The first 18 trusses were installed in shale roofs above Kentucky No. 9 seam and Illinois No. 6 seam. The remaining six were placed against the competent sandstone over the Pocahontas No. 3 seam in West Virginia. Chord tension was determined by two electrical resistance strain gages, in series, applied diametrically opposite to one another on the rod before tensioning. Due to the combined effects of inexact gage placement, rod bending and residual torsion in the chord due to tightening, errors in tension as high as 1780 N (400 lb) were reasonably possible. Due to faulty soldering or damage, three of the first 18 trusses and one of the final six were rendered completely unreliable. In addition to strain, the first natural frequency of vibration was observed to the nearest 0.1 Hz. Dimensions recorded included the span between contact points at the bearing blocks (Fig. 1) and the locations and amount of excess rod and rod gap at the wedge box and turnbuckle, respectively.

Jan 9, 1985

By F. N. Kissell, C. D. Litton

This study predicts the level of smoke that miners might meet while trying to escape a coal mine fire and describes how smoke would impede their safe escape. For this study, the authors assumed that miners exit through an escapeway adjacent to the burning entry, that some air would leak from the burning entry to the escapeway. The following conclusions were made: • A very low amount of air leakage to the escapeway can produce a critical level of visual obscurity from smoke. This shows that intake airways may be as susceptible to smoke visibility problems as return airways. • This critical level of smoke obscurity is reached much before a critical level of carbon monoxide is reached. • Small fires can cause a severe sensory irritation that further limits vision. Thus, reliable eye protection is very important. These results show that methods to guide miners through dense smoke will contribute greatly to saving lives during mine fires.

Jan 1, 1993

The 22nd Annual American Mining Hall of Fame Awards Banquet sponsored by the Mining Foundation of the Southwest will be held at the Westin La Paloma in Tucson, AZ on Saturday, Dec. 4, 2004. This year’s inductee, guest of honor and featured speaker at the banquet will be J. Steven Whisler, chairman and chief executive officer of Phelps Dodge. Whisler is also a director of Phelps Dodge, Burlington Northern Santa Fe, America West Holdings, the National Mining Association, the International Copper Association and the Copper Development Association.

Jan 1, 2004

By C. Green, J. Uhrie, C. Filippone, A. Guzman

A central aspect of heap leach management and recovery optimization is solution control. Insofar as each heap is unique in physical and metallurgical properties, it is essential to understand the hydraulic parameters that control the migration of solution on a case-by-case basis. Water Management Consultants, as part of an ongoing research effort for Phelps Dodge Process Technology Center, have adapted techniques of parameter estimation for application to data typically resulting from metallurgical column testing. The parameterization is completed within the context of a variably saturated flow model that allows interpretation of available hydraulic information collected during hydrometallurgical column tests. A novel interpretation approach is introduced to extract the necessary hydrodynamic parameters from typical hydrometallurgical data sets. Results from the application of the approach to standard metallurgical test data will be presented together with a discussion of the application of information gained to the design and operation of a heap.

Jan 1, 2002

Steady increases in longwall production have required operators to apply greater quantities of ventilating air in an effort to control and dilute respirable dust. Significant increases in shearer speeds necessitate that longwall supports also be advanced at a faster rate. Both of these factors may contribute to overall respirable dust levels on the longwall face because as supports are lowered and advanced, broken material falling from the top of the canopy is entrained directly into the air stream. To address this issue, the Pittsburgh Research Laboratory collected respirable dust samples from four longwall faces to characterize shield-generated dust. This paper investigates the influence of air velocity and shield advance rates on respirable dust levels. Also discussed are engineering controls currently used to reduce shield dust and alternative controls being investigated by the National Institute for Occupational Safety and Health (NIOSH).

Jan 4, 2010

By Phil Pennington, D. Jack Adams, G. Ward Wilson, Virginia T. McLemore, Luiza Aline F Gutierrez, Rodney Shields, Steven Lockwood, Samuel Tachie-Menson

Microorganisms are directly or indirectly involved in many chemical alterations and in the decomposition of minerals required for their growth. Microbial dissolution of sulfide minerals under acidic conditions can produce over 1,000 times more Acid Rock Drainage (ARD) than chemical action alone. Microbial actions can cause precipitation of minerals, adsorption or release of metals, and formation/destruction of organic-metallic complexes. Soluble minerals can serve as oxidizing substrates, electron donors/acceptors in redox reactions, and can be directly involved in cell metabolism. Microorganisms and microbial oxidation-reduction reactions and their contribution to mineral mobilization and stabilization will be discussed.

Jan 1, 2005

By David van Cleave, David L. Rome

Whether you buy your minicomputer from a manufacturer or another vendor, the first thing you must do is define your needs. With good planning, the initial cost will be low and your return on investment will be maximized over the long term. Involving all members of your staff who will he using the new computer in the planning phase is also important. Their participation will alleviate any potential concerns they may have about new equipment, and their suggestions will provide valuable input for your specifications. After you define your proposed system, survey available hardware and software. The survey will help you in the next step, preparation of specifications. The specifications, along with a quote request, are then sent to various manufacturers. Consider the Manufacturer When selecting your minicomputer, one important item to consider is the manufacturer. Remember, when you buy a computer, you're also buying the services of a computer company. A firm that makes a commitment to its customers and provides a product that is field tested before releasing it for sale is preferable. Examine the company's maintenance and support packages, since every machine requires preventive maintenance. Does your manufacturer or original equipment manufacturer (OEM) support service sites in your area? Has their service record been commendable? Will they provide training for your personnel and a supply of circuit boards so you can retain a degree of self-service autonomy? Three methods of buying a computer involve the manufacturer, an OEM, and the systems house. Buying direct from the manufacturer means you go straight to the source, using no middleman. This gives you maximum flexibility; you can consider every alternative and many possible combinations of computers, peripherals, and software until you find exactly the right system for you. The OEM buys computers direct from the manufacturer and builds them into his own computerized, special purpose product. He usually sells a complete package, including software and hardware, and often noncompetitive equipment as well (a scientific or engineering instrument, for example), designed for the mining market. Because he offers a packaged product, the OEM can often charge less for the system than if you put the pieces together yourself. In many ways, the OEM also provides a unique system. And while the OEM sells a packaged solution, he also usually has the special market knowledge necessary to modify the system to meet your unique needs, if necessary.

Jan 11, 1981

By Mohammed Laraba, Rodrigo Alvarez Garcia, Juan Maria Menendez-Aguado, Roula Abdelmalek

The aim of this research is the study of the WHIMS parameters on the improving process of a local (DD: Djebel Debbagh, East of Algeria) kaolin. The obtained results of performed XRF, SEM, and XRD characterization showed that this local material is an alumino-silicate containing kaolinite and halloysite with MnO and Fe2O3 impurities (respectively 39.30% and 34.67% alumina and 38.18% and 39.70% silica in both samples (DD2 and DD3). After homogenization, crushing, and milling, a multiparameters factorial experimentation (grain sizes, intensity, and dimension of matrix balls) showed that WHIMS is an effective process to improve the quality of this kaolin, mainly: removing their impurities. Dimensions of matrix balls (Db) = 2 cm, intensity of the applied magnetic field (I) = 1.5 T, and grain sizes (Dp) = > 100 < 250 μm) are the optimal values to reach 91.06% for manganese and 93.45% for iron as removing yield. The statistical analysis of these results sorted the investigation parameters and showed that Db has the highest and most significant influence on the recovery of iron and manganese particles. The magnetic field intensity (I) has a less important influence while the grain size has an average influence (positive on the iron recovery but a negative one on the recovery of manganese).

Jun 11, 2022

The National Mining Hall of Fame will hold its 13thAnnual Induction Banquet during MINExpo International 2000 in Las Vegas, NV. The gala black-tie (optional) event will honor eight legendary leaders of the mining industry. The event will take place at the Las Vegas Hilton Hotel on Sunday, Oct. 8. The induction ceremonies will salute mining greats elected by the board of governors from a list of nominees submitted by mining industry partners and the public. The members of the Class of 2000 will join 151 other inductees enshrined in the Mining Hall of Fame in Leadville, CO. The evening will begin at 6 pm with a cash bar reception followed by the banquet and program at 7 pm. Keynoting the banquet program will be Harrison (Jack) Schmitt. He was the geologist/astronaut of the Apollo 17 mission to the moon in 1972 (see related story on page 26). And he is the only scientist to “kick rocks on the moon.” Schmitt is also a member of the Mining Hall’s board of governors. Schmitt was also the keynote speaker at the First Annual Induction Banquet in Denver, CO in 1988.

Jan 1, 2000

By Tony Peach

Project Description The Ok Tedi Mine is located approximately 18 km east of the Papua and New Guinea-Indonesia border, on the southernmost extremity of the Star Mountains Range, it is situated almost equidistant from the north and south coastlines. The headwaters of the Fly River system are in the Star Mountains. The open pit mining activities are on Mt Fubilan with a (pre-mining) elevation of 2,095 metres (6,871 Feet) in the Western Province. The mine is in an area characterised by very steep topography and dense tropical rainforest. The pit has been free draining but will cease to be so in the first quarter of 2009. Ok Tedi Mining Limited (OTML) required a drainage tunnel to be driven under the mine, if possible before free drainage was no longer possible. The tunnel was required to be at least 5 m in diameter and 4,200 m (13,776 ft) long, with a possible extension of 1,100 m (3,608 Feet) if the mine decided it was required for additional drainage and underground exploration. The tunnel is being driven up grade at 0.67%, and will be connected to the pit by the raising boring of two 1.1 m (3 Ft. 6 In.) diameter shafts from the tunnel level 250 m (820 Feet) below to the pit. In Tabubil, the adjacent township at an elevation of 640 m (2,100 feet), air temperatures range from a mean at night of 20 (68°F) degrees centigrade to a daytime aver-age of 27 (81°F) degrees. Extremes of 12 and 39 (54°F?102°F) degrees centigrade have been recorded. Rain falls, on average, 339 days each year and totals 8,000 mm (315 inches), and have been known to approach 12,000 mm (472 inches) making the area one of the wettest places on earth. The portal site is at an elevation of 1,200 m or 4,000 ft and the air temperatures are a little cooler and the rainfall a little greater. Access to the mine is by air for personnel and light freight and by ship for heavier goods and materials. The port is at Kiunga on the Fly River 153 km from the portal site. The program for the project was tight, the decision to purchase the required TBM was made in July 2007 and the final decision to go ahead with the construction of the tunnel was made in November 2007.

By E. Carvajal I

Large diesel engines provide the mining industry the substantial power and torque needed to move large amounts of material efficiently. But the stresses generated by such power and torque necessitate complex maintenance programs to ensure the utmost operating capabilities are not compromised. Of all its available sensors, the Exhaust Temperature differential between the right and left banks can provide the most valuable indicator of the overall operating condition and potential degradation of a large diesel engine. BHP Billiton Escondida Mining has implemented real-time remote monitoring, diagnostics, reporting, and tracking of Exhaust Temperature differential using Modular® technology. As a result of the processes and procedures put into place surrounding their MineCare maintenance management system, Escondida has proactively replaced over 300 injectors, resulting in an increase of 4% in Engine availability.

Jan 1, 2011

By P. Anyon

Exposure to the microscopic particles in diesel engine exhaust can lead to serious health problems, including the incidence of cancers, heart disease and increased susceptibility to respiratory ailments such as pneumonia, bronchitis, and asthma. In Australia, mining companies and state government authorities are actively responding to this major occupational health and safety issue. Their initiatives place considerable emphasis on routine monitoring of diesel particle matter (DPM) exhaust emissions, both for engine benchmarking and as a part of routine engine maintenance. Implementation strategies follow two complementary paths: determination of individual engines? emission signatures combined with periodic engine re-certification; and co-operatively agreed industry-government engine maintenance programs, which are subject to audit. Both strategies place heavy reliance on real-time measurement of DPM concentrations in engine exhaust, using ruggedized instrumentation, mainly based on laser light scattering photometry. Adding value to this cooperative approach, industry has also collectively funded a government agency to design and manage a database, into which the results of all-routine DPM testing can be uploaded directly by individual mines. This win-win outcome is a great example of how cooperative action between governments and industry can deliver the goods: in this case, a safer working environment, more efficient energy use and the capacity to benchmark performance with industry peers.

Jan 1, 2009

By Charles LeMoyne

The Cable belt Company has been building single flight conveyors for a number of years. The simple design concepts of this type conveyor, introduced over thirty years ago, when distances of one to two miles were considered major advances in technology, remain relatively unchanged. Conveyors that are 6 to 20 miles (9.0 to 32 kilometers) long are being built and are presently in operation through- out the free world. The Cable Belt conveyor is not conventional in its construction. Cable welt differs from conventional troughed idler conveyors in that the driving medium and carrying medium are separated. Motion is provided by two endless steel cables running the length of the conveyor. The cables are driven by a single drive unit incorporating a differential gear which insures identical cable linear speeds and equal tension in both cables at all times. The belting is located and supported by "V" shaped shoeforms moulded to the belt which form a wedging action. The friction between the belting and rope is sufficient to prevent slippage (See figure 01).

Jan 1, 1983

By Robin J. Batterham

We still need to innovate, but it is getting harder. The real price of metals is declining, return on shareholder value is lower than other industries, and there is a shorter-term focus on staying viable in a capital-intensive industry where timeframes for implementation of new technologies can be long (+I5 years). In this environment, the levels of R&D spent by major minerals companies are remaining steady at around 0.2%-0.5% of revenue. This is not large and to remain viable in the future, we need to be smarter about the way in which we do R&D. The mining industry is a knowledge-based industry. Driving down the cost curve demands innovation, which demands knowledge. To be smarter and more effective in our approach to innovation, a new paradigm is required Generating, capturing and using knowledge has evolved from Mode 1 (discipline based and clear distinction between basic and applied research) to Mode 2 (multidisciplinary, team-based approached with flow between basic and applied activities). Mode 2 is now seen to be much more efficient and to deliver better appropriability (Tegart 2003). To survive, we need to innovate, and the best way to do this is collaboratively. Some examples and pointers for the future will be given in this paper. THE CURRENT SITUATION The Rand report and other recent studies have painted a grim outlook for the mining industry. The real price of metals continues to decline (Figure 1) and profit margins remain thin. This is reflected in shareholder returnwhich are well below other industries (Figure 2)-and current management strategies-which reflect something of a "survival mode." The current focus for most mining companies is on short-term, incremental gains

Jan 1, 2004

By Kwang ‘Min’ Kim, Paul T. Behum

The Old Bevier Aerobic Wetland in Macon County, Missouri, was constructed between 1990 and 1991 by the Missouri Department of Natural Resources’ Land Reclamation Program for the purpose of treating acid mine drainage (AMD). The principal source of the AMD is from an underground mine that operated during the 1920&apos;s through 1950&apos;s, which was partially exposed during surface mining in the 1960’s. Limestone bedding of an AMD collection system provided alkalinity similar to an anoxic limestone drain (ALD). Because the original aerobic wetland failed when a critical dilution water supply became unavailable, the total acidity of the AMD overwhelmed the limited neutralization ability of the aerobic wetland. The aquatic vegetation deteriorated and treatment became ineffective. The Missouri Land Reclamation Program with the assistance of the Office of Surface Mining, Mid-Continent Regional Coordinating Center rehabilitated the Old Bevier Aerobic Wetland in 2001, incorporating newer technologies to improve the performance. The new system, Old Bevier II treatment facility, consists of a 2-stage vertical flow pond (VFP) with associated oxidation cells and aerobic wetlands. This paper discusses the performance of this passive AMD treatment system, updating an earlier report. The new treatment system has operated with nearly continuous net alkaline discharge and a high iron removal rate. Treatment improves during warm months when emergent vegetation is fully established and biologic activity is greater. Reduction in system efficiency is evident during winter months.

Jan 1, 2005

By E. Fahrenkrog, D. Sbartaro, E. N. Cifuentes

An intelligent supervisor using expert system tools and applied to a crushing plant has been developed with a structure based on a model of a human operator. It consists of a knowledge base containing a qualitative model of the process and a rules base with the heuristic logic used by an operator when supervising a plant. The simulation results obtained show the potential of this type of system to supervise the automatic operation of a plant. There has been very significant development in artificial intelligence over the last two decades. Within this development, two approaches can be distinguished, (Winston, 1984). The "model approach," in which the main objective is to understand and model the be¬havior of living systems. The second approach is the "engineering approach." Here, systems capable of performing tasks usually requiring human intelligence are created. As part of this latter approach, knowledge engineering and its main achievement, expert systems, have been developed. Expert systems arose from the need to incorporate the abilities of a human expert in solving realistic problems in which the conventional approach has great difficulties. The first successful applications of expert systems were in medical diagnosis, geophysics, and fault detection. However, since 1971, when Fu (1971; defined intelligent control as the inter action of artificial intelligence and automatic control, some significant developments in the use of artificial intelligence tools for process control have been achieved (Astrom, 1986; Pinto 1988; Fahrenkrog, 1988; and Porter 1987). The modern control theory has made important advances. And, although successful in some applications, it has failed to cope with the practicalities of many industrial processes. As a result, the automatic operation of a plant has been confined to a small region around a normal operating point and to periods without any great disturbance. One of the main reasons for this is the lack of accurate and structured knowledge of the processes involved. Despite this, operators applying their knowledge, experience, and a little intuition, often obtain good results controlling the plant in such situations. Considering the above, the next obvious step is to include similar reasoning capacities in a computational system. The development of such an expert supervisory system prototype applied to a mineral crushing plant is presented. Problem description The problem is to conceive a control system with the ability to handle quali-

Jan 1, 1989

On Nov 1, 2007 House Resolution 2262 ? The Hardrock Mining and Reclamation Act of 2007 ? was passed by the U.S. House by a vote of 244-166. HR-2262, among other things, would impose a 4-per-cent royalty on existing mines with commercial production and an 8-percent gross royalty on all new claims. Not surprisingly, this possible new law was one of the hottest topics of discussion at the Northwest Mining Association?s conference that this year returned to Spokane, WA for its 113th annual meeting on Dec. 3-7. More than 1,800 delegates attended the conference that was held under the banner theme of ?Mining ?. For today and tomorrow.? Northwest Mining Association executive director Laura Skaer was one of many speakers during the three-day conference to respond to the threat to the industry posed by HR-2262 with a presentation titled ?Potential changes to the 1872 Mining Law.? In the presentation that she first unveiled at the Alaska Miners Association?s convention and trade show on Nov. 8, Skaer laid out a comprehensive list of problems with HR-2262. In addition to the association?s obvious concerns about the proposed royalty, Skaer noted that the bill includes a mine veto provision that would allow the Secretary of the Interior the authority to deny an operations permit to a project if the secretary determines that the operation would cause undue degradation to public lands and resources. Potential massive withdrawals from mineral entry are also included in HR-2262. Among the lands that could be off limits to miners under HR-2262 are wilderness study areas, areas of environmental concern and 23.6 hm2 (58.5 million acres) identified as Roadless Rule. States, political subdivisions and Indian Tribes would also have more authority to withdraw lands, she said. To combat the proposed changes, Skaer made 10 trips to Washington D.C. on behalf of NWMA members in 2007. In her presentation at the annual meeting, she also objected to provisions that include no life-of-mine permits and uncertain permit renewals and new and duplicative environmental standards that she said are vague, ambiguous and inconsistent with current federal and state environmental laws. Debra W. Struhsacker, an environmental permitting and government relations consultant, also spoke on the issue of HR-2262 with a presentation titled ?The House mining law bill ? Rip van Winkle is back ? and he?s meaner than ever.?

Jan 1, 2008

By SH. Shahsavari, H. Akbari, M. Noaparast, M. Oliazadeh

Mejel valley zircon ore in Iran is located in north part of Iran and was sampled to evaluate its concentration. The aim of this project was to define the mineralogy of this zone and separating zircon from other minerals using gravity concentrators and magnetic separators. It is constituted of various valuable minerals, mainly zirconium, niobium-tantalum, titanium, rare earth elements particularly cerium-bearing minerals namely zircon, sphene and rare earth elements oxides. We used statistical method for designing of experiments. Yates method used for analysis of basic experiments results. The grade of zircon in primary sample was 1.1%. Different experiments were designed to optimize all required parameters. The final concentration with 75% zircon was produced and final recovery was 79%. Finally, lab-scale based flow sheet was prepared using experiments results.

Jan 1, 2005