Search Documents

By Paul D. Tomlingson

There are huge benefits for mining operations that have a well-defined maintenance program that is understood and followed across the total operation. But for operations lacking a quality maintenance program, there is equal assurance that nearly every major maintenance problem can be traced to this omission. Few problems will be permanently corrected until such a program is implemented. Definition The maintenance program re-quires the interaction of all mine departments. Initially, the production department will request work and the maintenance department will identify work, principally through preventive maintenance inspection and testing efforts. Maintenance will then classify the new work to determine the best way to respond. Maintenance will plan selected major jobs to enable its crews to carry them out more effectively. Maintenance will schedule the planned work with operations. Supervisors will assign all types of work to their crews then, control the work through effective supervision. As work is completed, maintenance will measure the work using an accurate information system. Next, it will assess overall accomplishments against goals such as performance standards or budgets. In addition, the pro-gram would prescribe a means to evaluate every aspect of the operation as it affects maintenance so that necessary improvements or changes can be identified, prioritized and acted on. Such evaluations should be part of a mine-wide continuous improvement effort. A well-defined maintenance program is one of the best investments a mining operation can make to assure its profitability. Educating the total operation on the pro-gram assures long-term dividends from the investment.

Jan 1, 2008

By M. Z. A. Bakar

To investigate the differences in the radial drag pick cutting performance in dry and saturated sandstone, a suite of linear rock cutting test was performed using linear rock cutting machine (LRCM). Experimental results of 50 data passes, incorporating 350 data cuts were used to compute cutting, normal and side forces required for determination of other performance related parameters. Although the forces required to cut the dry and saturated rock were in congruence for most of the spacing and depths of cut combinations; but the overall averaged cutting and normal forces for saturated rock cutting were found to be 9.9% and 9.4% respectively higher than the dry rock cutting. The increase in the overall averaged forces was attributed to strength variability of one of the saturated block affecting the overall forces. The side forces experienced a negligible drop in saturated rock cutting. An increase of 28% and 9% in the actual and nominal specific energy values respectively was also recorded when cutting saturated rock as compared to the dry rock cutting. The increase in saturated rock specific energy is attributed to production of large amount of fines and few large sized chips directly contributing towards increase in specific energy. The optimum s/d ratio for dry rock tests was found to lie between 6 and 8 whereas for saturated rock cuts this value lied between 5 and 9.

Jan 1, 2012

Every two years, industry leaders and practitioners of tunneling and underground construction gather at the Rapid Excavation and Tunneling Conference (RETC) to learn from their peers about the most recent advances and breakthroughs in this unique fleld. Industry experts from around the world highlight their most recent projects and share real-world experiences. They also share with their colleagues new technologies and methodologies that attendees can take home to their respective projects. The 2013 RETC was held June 23-26 in Washing-ton, D.C., itself home to several major tunneling and underground construction projects. The conference is sponsored by SME. Attendance was 1,384 professionals. The accompanying exhibit hosted 159 companies in 188 booths. A few of the topics covered in the technical sessions dealt with caverns and large spans, contracting practices, tunnel linings, design and planning, geotechnical considerations and instrumentation. The conference was preceded by four short courses, all well attended. They were ?Grouting in Underground Construction,? ?Tunnel Lining Design,? ?Microtunneling Application? and ?Risk, Uncertainty and Hard Decisions.? In addition, a sold-out field trip to D.C. Water?s Blue Plains Tunnel took place following the conference. The Blue Plains Tunnel is part of the agency?s Clean Rivers Project. Also during the meeting, three students each received $5,000 scholarships from the UCA of SME, while another three students each received $2,500 scholarships from RETC (See page 53).

Sep 1, 2013

By B. Slaker

The ability to detect and quantify ground movements in underground mine workings is of the utmost importance to the safety of miners and continuity of operations. Rib sloughage is one of the most common forms of underground deformations. Remote sensing techniques, such as laser scanning, can be used to quantify this rib sloughage, by recording precise, time-lapse point clouds of mine workings. In order to determine sloughage volumes and locations, a total of 11 laser scans were performed 41 days apart at a working section of an underground limestone mine. During this period, significant sloughing and scaling occurred, allowing for differentiation between the initial and final point clouds.

Feb 27, 2013

By V. Osterholt

Sustainable development of mineral resources is based on a spatial model of the orebody that is only partly known from exploration drilling and associated geological interpretations. As a result, orebody models generated from the available information are uncertain and require the use of stochastic conditional simulation technique. This paper considers three methods for simulating orebody geology: (1) pluri-Gaussian simulation that limits the allowable contacts between the various units; (2) sequential indicator simulation using indicator kriging; and (3) an experimental multiple-point approach that captures some higher-order spatial statistics. The data requirements of the methods, how to meet them in mining applications, and performance characteristics are discussed. The application of these methods in a hypothetical deposit consisting of three geological units provides a comparison and illustrates the advantages of the different simulation approaches.

Jan 1, 2005

By Ann L. Backstrom

The Apex Tunnel is part of the Southern Nevada Water Authority?s proposed Clark, Lincoln, and White Pine Counties Groundwater Development Project. The project is intended to develop unused Nevada groundwater for meeting the water needs of Southern Nevada and would involve over 322 km (200 mi) of water transmission facilities. The Apex Tunnel, as currently conceived by ongoing planning and environmental analyses, would extend 2804 m (9,200 ft) through a structurally complex terrain of Paleozoic carbonate rocks and younger basin fill deposits and will traverse both public and private lands. Several faults cross the tunnel study area, juxtaposing rocks of varying lithology and degree of folding, and creating intervals of differing rock conditions along the tunnel alignment. This paper discusses how the geotechnical program was developed to be flexible and allow for rapid implementation of revisions based on new knowledge that became available during program execution, resulting in more effective decision making and enhanced value from the geologic investigation during the planning phase of the project.

By R. Benito

This paper describes the development of a life of mine schedule (LOM) for one of the world?s largest known sedimentary Copper-Cobalt districts located in the Katanga Province, Democratic Republic of Congo (DRC). A particular feature of the Tenke Fungurume LOM schedule is the considerable number of pits/phases for scheduling, each competing to provide the best ore available to a capacity constrained process facility. This paper discusses the main scheduling objectives and constraints, data pre-processing as a scheduling aid, the mine scheduling approach, and results and conclusions.

Jan 1, 2011

By H. Y. Sohn, R. D. Hagni, M. K. Kojo

Reflected light microscopy was used to study the mineralogy and textures of experimental reactions of a nickel concentrate with a slag. Such an interaction is an important step in the bath smelting of nickel sulfide concentrate. Concentrate particles in the central portions of the pellets are rounded and develop vermicular SO2 gas porosity. In the outer portions of the pellets, the original minerals of the concentrate, pyrrhotite, pentlandite, pyrite, chalcopyrite, and violarite have agglomerated and reacted to form two intergrown phases: 1) pyrrhotite solid solution (Fe0.75Ni0.18Cu0.01S) and pentlandite solid solution (Fe0.58Ni0.51Cu0.03S). Magnetite formed euhedral crystals, skeletal crystals, and dendrites at the margins of the matte. Prismatic ferrohypersthene and octahedral Mg-Al-Fe spinel crystals and dendrites are present in the glassy slag.

Jan 1, 2001

By Shawn Collins

BACKGROUND The history of the Pine Point Mine is a rich one. This property once boasted one of the largest and most profitable lead-zinc mines in Canada's long and storied mining history. The Pine Point mine used open pit technology to extract the ore, but they faced several challenges. In addition to logistics problems with haul distances and metal prices, the mine faced the challenge of a large in flow of water from the Great Slave Lake. Eventually, the Pine Point Mine was closed leaving behind a large deposit of lead-zinc ore. Following the closing of the Pint Point Mine, Tamerlane Ventures Inc. acquired this property which includes approximately 70 million tonnes of lead-zinc reserves. The initial phase of this project will concentrate on the R-190 deposit as a test site to prove their new approach for extracting the ore. The R-190 reserve is believed to have approximately 1,014,000 million tonnes of high grade ore varying from 5% to 52% combined lead-zinc. Once the pilot project proves the approach is valid, the process will be repeated in approximately 33 other ore bodies on the property. This paper is written to discuss the design process to determine the most effective means of placing production and service equipment in the same shaft. Currently the design work and the mining scheme is complete, but lead-zinc pricing has prevented Tamerlane Ventures Inc. from moving forward with the project.

To simplify programming, image analyzers commonly measure either linear intercepts or the areas of particles and grains to determine liberation based on polished section mounts. However, the concentration of minerals by flotation is based on reagents that interact with the exposed surfaces of the minerals. Thus, it is often perceived that image analyzers should measure the perimeter of the mineral of interest in the ore particles. A comparative liberation study of thirteen samples collected from a flotation plant processing a complex base metal sulfide ore showed that the liberation of the ore minerals determined by area measurements is very similar to the liberation determined by the exposed perimeters. The liberation determined by exposed perimeters is more appropriate only for those cases where the mineral texture is so complex that it is retained in the small particles generated in conventional grinding operations.

Jan 1, 2002

By S. J. Stokowski

Abstract An extensive drilling and laboratory testing program indicates that a construction aggregate resource is present within the Oligocene Sombrerito Formation limestone, southwestern Dominican Republic. The first part of the testing program included the collection, photographing and geologic logging of diamond drill cores to allow lithologic subdivision of the strata into potential quarry layers. The primary lithostratigraphic units are: I- (youngest) approximately 10 m of white, dense marine limestone II-approximately 5 m of white, interbedded dense and chalky marine limestone III-more than 2 m of tan, chalky, calcitic dolomite. Unit I is often altered by lateritic weathering and/or dolomitization. Unit II is often altered by dolomitization. The cores were individually crushed by quarry layer into coarse and fine aggregate sizes for chemical and physical analyses: specific gravity and absorption, MgSO4 soundness, sand equivalent, Atterberg limits of the minus #40 mesh fraction, and LA degradation. The unaltered portion of Unit I is suitable for all construction aggregate uses. Unit II is best suited for crushed stone base. Each of the non-weathered units decreases in coarse-aggregate yield and quality with depth and diagenetic dolomitization. Dolomitization typically causes about 5% lower yield of coarse aggregate, a sand equivalent of about 20 units below the original value an increase in absorption of about 3%, an increase in the LA of up to 13%, and a decrease in the average five-cycle MgSO4 soundness of about 17%.

Jan 1, 1991

By Wu Xueling

9K medium was used to isolate iron-oxidizing bacteria from 27 sump water samples collected from Dexing Cop-per Mine, Chengmen Mountain Mine and Yin Mountain Mine, Jiangxi Province, China. Lead acetate and silver nitrate were used to enrich metal-resistant iron-oxidizing bacteria from the above water samples. Isolate 16 was isolated from the sample taken at Dexing Copper Mine. Growth experiments indicated that when incubated under lead acetate (3,500 mg/L), isolate 16 still carried out ferrous ion oxidation, while isolate H1, a less resistant strain taken at Yin Mountain Mine, had a tolerance level of only 400 mg/L. When assayed with other metals, i.e., Ag+ (240 mg/L), Hg2+ (0.9 mg/L), Cu2+ (32,000 mg/L) and Mg2+ (22,500 mg/L), isolate 16 still carried out ferrous ion oxidation while, on the other hand, isolate H1 exhibited much lower tolerance levels, i.e., Ag+ (60 mg/L), Hg2+ (0.1 mg/L), Cu2+ (19,000 mg/L) and Mg2+ (13,500 mg/L). Based on 16S rDNA sequence data, isolate 16 and H1 were both identified as Acidithiobacillus ferrooxidans.

Jan 1, 2007

By K. Mondal

A macroscopic approach integrated with microscopic analyses for wettability characterization is presented. Wetting depends on 1) Contact between the dust and the fluid droplets, 2) Wettability of the particles by the wetting fluid, and 3) Wettability rate (due to low contact times). The goal of this paper is to show that the wetting rate is a significant factor in dust control. Samples from the roof, three different horizons of the coal seam and the floor were pulverized to less than 25 µm. Experiments were conducted with known wetting fluids to correlate surface tension and equilibrium wettability. Further analyses were performed in terms of surface charge (zeta potential), particle size, mineral composition, elemental composition, and quartz content. The surface tension reduction was also achieved by the use of chemicals and/or altering the temperature of the water. Two methods were used to evaluate wettability rates: a) near real-time comparison of wettability rates, and b) comprehensive evaluation of the intrinsic wettability rates. The data obtained provides meaningful insights towards the design of engineering controls for an economical solution to dust control in coal mines.

Jan 1, 2012

By M. Schafer

The 20 foot diameter cast-in-place tunnel lining for Phase 3 of the Mill Creek Tunnel (MCT-3) has been completed. This paper will summarize aspects of liner design and address the construction approach in placing the liner in areas of tunnel that experienced crown overbreak. Tunnel lining production rates, installation procedures and form buoyancies experienced during concrete placement will also be presented.

Jan 1, 2008

The Forestry Reclamation Approach (FRA) specifies that the upper 1.22 m of material on the reclaimed surface should be left as uncompacted as possible to facilitate tree root growth. One of the main concerns about applying the FRA to steep slopes is that the upper 1.22 m of material could cause the reclaimed slopes to be unstable. Successful application of FRA on flat and rolling surfaces precipitated this investigation. Details of a field investigation conducted at a steep-slope mine are available in an earlier publication (Kumar and Sweigard, 2011). A total of 70 survey monuments were driven into the slope in a regular pattern to monitor slope movement. Quarterly surveys of the monuments were done to quantify any type of mass movement either horizontally or vertically. The methodology proposed for slope movement was verified using numerical models. Analytical models based on limit equilibrium technique and numerical models based on the finite element method were developed for slope stability analysis. The limit equilibrium analysis was done using Geo-Slope software following the Simplified Bishop Method. The finite element (FEM) numerical model was developed using the Plaxis computer program following the strength reduction technique. Two kinds of slope stability analysis were performed: first with the top 1.22 m of loose material and second without top loose material. Finally, the field investigation results were compared with stability analysis results. Both of these approaches showed that application of the FRA on steep slopes is not causing any significant instability problems that would not exist otherwise for overly steepened slopes. Keywords: Forestry reclamation approach, steep slope, slope movement, factor of safety

Feb 27, 2013

By Thom Seal, S. J. Jung

This paper will combine three SME annual meeting presentations on reducing gold inventory in cyanide heap leaching. Information on Part I – Side slope leaching (SME 2003), Part II – Determining the dry zones using geophysical resistivity (SME 2004), and Part III - Presents a new technology “Hydro-Jex”, to introduce the required lixiviants to the un-leach or under-leach zones in heaps (SME 2005). This paper will describe how Newmont Mining Corporation continues to improve the economics of the heap leaching process for precious metals recovery.

Jan 1, 2005

By R. Steele

In addition to compliance with government emissions and reporting requirements, mining and mineral processing companies are increasing energy efficiency to reduce costs and become more competitive in the global marketplace. One of the major obstacles to identifying opportunities for increased energy efficiency is the lack of readily available data on energy use, and more importantly the energy use linked to production data, that identify energy reduction opportunities. As well as energy reduction, mining and mineral processing companies often struggle with the prediction of energy use, and are often penalized for under or over forecasting. Once again, it is the lack of timely information that makes this prediction difficult. This paper looks at expanding the use of a Manufacturing Execution Systems by integrating with Energy Solutions. This will provide automatic, timely information, at a granularity that makes it easier to identify energy reduction opportunities, reduce energy costs, and better predict energy use in a mining and mineral processing operation.

Jan 1, 2011

By Bob Rautenberg

The Construction of Tunnel and Edison Force Mains contract involves the installation of two new force mains to provide a redundant means for sewage conveyance from Middlesex County Utility Authority?s (MCUA) Edison Pump Station on the northern shore of the Raritan River to the Central Wastewater Treatment Plant on the southern shore. The force mains will be installed in a 1,192 m (3,910 lineal foot) long tunnel with a 4.09 m (13'-5') inside diameter, fully gasketed precast concrete segmental lining, which is to be tunneled underneath the Raritan River utilizing an Earth Pressure Balance TBM. The tunnel is anticipated to encounter flowing soils near and beneath the river. Two new 60-inch diameter Centrifugal Cast Fiberglass Reinforced Polymer Mortar force mains will be installed within the tunnel leaving an open utility corridor above the force mains for future consideration. The project also includes the design and construction of two slurry wall shafts with associated piping. The paper will provide an overview of design and provide a case history of the construction of the tunnel and highlights of the construction methods implemented to date.

By J. C. Stankus

To protect mine personnel and moving equipment at underground roof fall areas, mine operators typically install steel sets, which are covered with wooden blocks and backfilled with an expanding type cement material. In large roof falls, the cost of void backfilling becomes prohibitively high causing some mines to leave the voids open. However, the durability of wood over time and the capability of the steel set and wood lagging to resist falling rock are unknown. This has caused concerns for the Mine Safety and Health Administration (MSHA) and ground control engineers. During past two years, Keystone Mining Services, LLC designed and developed various impact-resistant steel set designs that were approved by MSHA and installed in various underground fall rehabilitations. This paper presents the patent pending impact-resistant steel set design methodology, including (1) steel set design per AISC national standard, (2) design, development, and laboratory testing of a water proof composite impact resistant lagging panel, and (3) impact resistant steel set design based on Law of Conservation of Energy. Two underground cases will be included detailing the application of the system.

Jan 1, 2011

Traditional fine grinding mills in mineral processing relied on the use of steel medium for particle size reduction. The successful development of the Isa Mill(a horizontal stirred mill with 3000 litres of net chamber volume and 1120 kW rated motor power)adopted a novel product separator design that has led to a major revision of medium use in fine grinding. The Isa Mill separator has also successfully operated with a wide variety of medium types such as silica sands, river gravel, smelter slag, run-of-mine ore fractions and steel shots, with size ranges from 0.5 to 10 mm. A great flexibility of the Isa Mill operations has been achieved for processing a feed as coarse as 120 um to a product as fine as 5 µm. This paper discusses the performance of two inert grinding media used in the Isa Mills in Mount Isa Mines of Australia for processing galena and sphalerite bearing ores to below 10 microns. They are the copper reverberatory furnace slag (CRFS)and the heavy medium plant rejects (HMPR). A methodology was also demonstrated for comparing the medium performance and for scaling up the Isa Mills from a 1.5-litre laboratory batch mill to a full scale 3000-litre mill.

Jan 1, 2000