Search Documents

By R. Strandahl

As one of the largest private utilities globally, E.ON currently operates hard coal fired power stations in with a total installed capacity of some 20.000 MW: These thermal power plants consume domestic coals but are increasingly dependent on imported seaborne traded coal (in 2009 approx. 17 million t). Knowing that the company’s reputation and credibility depends in part on how E.ON lives up to the responsibilities along the entire energy value chain, E.ON takes a collaborative approach with the various suppliers. Hence, E.ON’s responsible policy also applies to the procurement of coal; the utility launched in 2009 a comprehensive Corporate Responsibility program with special focus on supply-chain audits. One of the first coal audits focussed on the Cerrejón coal mine in North Eastern Colombia. The authors will share the key learning’s and experience from the Colombian audit jointly conducted with an independent auditor and E.ON experts from the Corporate CR and E.ON Energy Trading.

Jan 1, 2011

By Luminita Calin

King County (Seattle, WA) is on a monumental task of building the new Brightwater System complete with a new treatment plant, three main conveyance tunnels, a new outfall into Puget Sound and other ancillary works. This paper will describe the first conveyance tunnel, Brightwater East currently under construction by the Joint Venture of Kenny (Sponsor) / Shea / Traylor that is scheduled for completion in early 2010. The project located in Bothell, WA (north of Seattle) is in both King and Snohomish Counties. It was the first of the major tunnel projects that was scheduled by King County for the Brightwater System. The East Contract consists of the following major elements: 14,000 ft of 19'-2' EPBTBM mined tunnel using 16'-8' ID bolted, gasketed precast concrete segments for a primary liner; installing and encasing 14,200 ft each of 48', 66', 27', 84' in diameter steel pipes inside the tunnel along with three runs of fiberoptic cable; 2,430 ft of 72' in diameter microtunnel including three caisson shafts and associated structures; one Intercepting Structure (IS) shell to mine from that is 74 ft deep and 74 ft finished in diameter with 130 ft deep slurry diaphragm walls, tremie slab and final concrete wall lining; one Influent Pump Station shell (IPS) 83 ft deep, twin 77 ft inside diameter cells, with 160 ft deep slurry diaphragm walls, tremie slab, and final lining; two short 12 ft in diameter inter-shaft connector tunnels; one extraction shaft 40 ft deep by 40 ft wide and 140 ft long for connection to the new treatment plant piping.

By John E. Tilton

During the past several years — much to the delight of producing firms and countries — copper prices have surged from under $1 to more than $3/lb. Anyone familiar with the industry also knows that since the early 1970s the long-run trend in real copper prices has been significantly downward. This sharp contrast between short-run and long-run trends raises the issue of the forces behind these developments. What has been driving short-run prices up and long-run prices down? Simple economics suggests that it is all a matter of supply and demand. When demand is rising faster than supply, prices will rise and vice versa.

Jan 1, 2006

By Dan Witkowsky

For the 36th consecutive summer, the Colorado Mining Association Education Foundation and the Colorado School of Mines have sponsored “A Total Concept of the Mining Industry” for kindergarten through grade 12 teachers. Teachers from 34 states, plus the District of Columbia and two foreign countries, have graduated from the four-week course. They received six hours of recertification credit. This summer 31 teachers from Colorado, Kentucky, Virginia and Alaska completed the program. The course is unique from other shorter courses in that it solicits teachers of all disciplines from all K-12classes. In addition to the expected earth science and mathematics teachers, the Class of 2004 consisted of educators who teach music, chemistry, biology, social studies, history, basic English and world history. Others in the program included those who teach American history, physical and life science, remedial reading, consumer/family studies, “world of work,” language arts, engineering technology, environmental science, world geography, human anatomy and physiology, and business.

Jan 1, 2004

Beneath some of New York?s most iconic buildings ? The Met Life Building, the Helmsley Building, the Waldorf Astoria ? crews are busily at work on the Metropolitan Transportation Authority?s long-awaited East Side Access (ESA) project. In fact, it is 14 floors beneath the famed Grand Central Station where one of the centerpieces of the project, the new Long Island Railroad (LIRR) station terminal, is being blasted and carved into shape. When completed in 2016, the $7.3-billion ESA project will increase LIRR?s capacity into Manhattan and significantly relieve congestion at Penn Station. Currently, 37 LIRR trains per rush hour roll into the crowded Penn Station where many riders must then transfer to subway trains to complete their commute. When completed, the ESA tunnels will bring an estimated 160,000 riders directly to Grand Central Station, saving those riders 30 to 40 minutes. Studies have found that more people work within walking distance of Grand Central than Penn Station. ?The benefits of the project are tremendous,? MTA Capital Construction President Michael Horodniceanu told more than 340 industry professionals attending the UCA of SME?s George A. Fox Conference in New York on Jan. 26. ?The ESA is the first expansion of the LIRR in 100 years. It will increase the East River tunnel capacity by 50 percent and will help support job growth around Grand Central.?

Jan 3, 2010

By Chaoxun Zhao, Daniel Tao, Craig Blue, Narendra B. Dahotre, Rick Honaker, Bhupendra K. Parekh, Hongyang Han

Equipment wear and corrosion have significant adverse impacts on the operating cost and efficiency of mineral processing plants. In this project advanced surface enhancement technologies are being investigated to decrease the wear and corrosion rate of metal surface. Enhanced metal surfaces are achieved through surface conversion, enrichment, and coating by use of advanced High-Density Infrared (HDI) and other technologies. Studies have been done to determine the effects of process parameters on surface properties and identify optimum conditions. The microstructure of the enhanced metal surfaces was characterized by SEM, EDS, and microindentation. Laboratory wear testing was carried out to investigate the wear performance and the viable coating candidate was determined.

Jan 1, 2005

By N. L. Hayward, V. H. Ness

In the past decade Australia has seen the development, construction and commissioning of three complex processing plants for the treatment of lateritic nickel ores. These have all been based on high pressure acid leaching (HPAL) for extraction of nickel and cobalt into solution, followed by solid liquid separation in a CCD circuit. However, flowsheets for separation and purification of the nickel and cobalt diverge markedly. The existing plants have been commissioned with varying degrees of success, with a variety of problems ranging from materials of construction to inadequate design. While the process problems are not insurmountable, there is much room for improvement. Currently there are several new HPAL plants at the feasibility or financing stage. All of these have adopted one of the existing flowsheets. Most of the enhancements have focused on increasing autoclave size. It is now time to assess the success and failures of the three existing plants and incorporate this experience in a design for productivity, efficiency and reliability. Towards this end, this paper discusses aspects of flowsheet optimization, materials of construction and engineering design.

Jan 1, 2001

In the dimension stone industry, workers in processing shops may be exposed to harmful levels of respirable silica dust when conducting the different tasks in stone preparation, which include cutting, grinding, polishing, and thermaling. To protect workers from this health hazard, operators sometimes ventilate processing shops using fan-powered dust collectors to capture and filter dust. To investigate this issue, NIOSH, Pittsburgh Research Laboratory, in cooperation with a dimension stone operation, upgraded an off-the-shelf dust collector the operator was utilizing in a polishing/cutting shop. Initial dust surveys showed that the unit was under-designed for the amount of dust being generated in the shop. The objective of the research was to cost-effectively increase the air cleaning volume and improve dust capture efficiency of the unit with a larger motor and blower. The unit?s original stock 0.56 kw motor and blower was replaced with a 2.24 kw motor and matching blower to increase airflow. The unit was evaluated both in the laboratory and the shop before and after the retrofit to determine the improvement of the upgrade. The study showed that the 2.24 kw upgrade improved the performance over the original 0.56 kw motor resulting in more dust being cleaned from the ambient air in the shop. The 2.24 kw unit cleaned 19% more air and captured 32% more respirable dust than the 0.56 kw unit.

Jan 1, 2009

Breaks in coal slurry impoundments can threaten the lives and health of area residents, destroy homes and businesses and contaminate water supplies. This dangerous potential looms over coalmining regions in West Virginia and throughout Appalachia. The Coal Impoundment Project was begun in June 2003 to provide an inventory and mapping of active and abandoned impoundments in West Virginia. The project also provides the public with specific information about the impoundments in their communities. It is dedicated to alerting residents of danger and evacuation plans, reducing risk to residents and finding alternatives to impoundments. Since its first year, more than 100 impoundment sites have been added to the project’s Website.

Jan 1, 2005

By Wern-ping Chen

Technical and non-technical challenges exist in each mega infrastructure project. It?s no exception to the first US underground PPP Port of Miami Tunnel (POMT) project in Miami, FL. The POMT will connect two man-made islands, the Dodge and the Watson Islands, under the Biscayne Bay within highly porous limestone formation. Permeability as high as 0.1 cm/sec has been identified. Its 41-ft outside diameter, if constructed, is the largest precast segment lining in the US. Besides its geological and hydro geological challenges and risks, local community influence and impacts have controlled the fate of this project. This paper describes its tender design enhancements and the evolving of its slow advancement in resolving local community issues.

By Lee W. Saperstien

At the heart of the mining process are a number of basic and fundamental tasks whose regular and repeated performance constitute the mining cycle. As will be discussed presently, these tasks are the basic components of the mining system. Section 9, Production Operations, provides the mine designer and engineer with an understanding of these tasks and with sufficient design principles to allow this person to create an efficient mine system. This section is meant to be an introduction and adjunct to subsequent sections that describe specific mining systems. However, sufficient design information is included here for the independent design of mine systems that may not be described elsewhere or for subsequent verification of existing designs. For the purposes of this section, mining subsumes excavation; thus this material applies to any excavation process. Accordingly, this section is written in general enough terms to include both surface and underground mining. It may be used also for civil engineering excavations that often involve the same steps. Obviously, the actual procedures undertaken in any specific mining system will appear to be very different from those taken in any other system. This is certainly true when comparing surface with underground methods. Yet the fundamental principles are often the same. This segment is written to explicate the basics. Wherever appropriate, the section will suggest the differences between the application process to surface or to underground mining.

Jan 1, 2008

By R. Yang

This paper presents a kinematic approach for blast modeling with examples of blast models that were developed previously. A kinematic approach was applied successfully in developing blasting models that can simulate all blast design parameters for field applications. Several applied blasting models have been developed and applied widely in the world. A kinematic approach to blast modeling refers to using measurements of kinematic quantities such as the velocity, strain, or displacement and well-established assumptions to model blasting phenomena, rather than being restricted to use first principal of physics, such as, the stress- and material-constitutive relations. The kinematic quantities are easy to measure in the field. Due to the complexity and inhomogeneity of rock mass properties, using first principles of physics, many parameters of rock and explosive properties must be involved, which are hard or impossible to quantify. This creates a major impediment when trying to simulate the total process of blasting based upon first principles of physics. The 3D kinematic model for muckpile formation was developed and applied to open pit blasts. The multiple blasthole fragmentation model developed during recent years has been applied successfully to many mine sites around the globe. These models are typical examples of blast modeling using the kinematic approach, which enables the models to catch major trends of the blasting process and explicitly simulate full blast design parameters and complex geometries. Blast modeling using the kinematic approach results in easy model calibration and validation against field measurements and effective applications to practical problems. Using kinematic models of the muckpile formation and the multiple blasthole fragmentation model, this paper demonstrates the merits of the kinematic approach for blast modeling. New developments of the models were also presented in the paper, which illustrate the potential of the kinematic modelling approach.

Mar 2, 2022

By L. Franko, S. Klima

Wet-drum magnetic separators are used extensively for upgrading iron ore and for magnetite recovery in dense-medium circuits. In this study the performance of a continuous, laboratory wet-drum magnetic separator was evaluated with and without the application of ultrasonic energy when processing dense medium slurries. Test variables included magnetic-to-nonmagnetic ratio, solids concentration, and nonmagnetic materials. The results indicate that under certain conditions, the purity of the magnetic material increased after ultrasonic treatment.

Jan 1, 2001

By A. Habibi

The ventilation survey was conducted in an underground longwall trona mine. The mine is relatively shallow and categorized as a gassy mine. The ventilation system consists of nine shafts (three intakes and six exhausts). Three surface based axial fans ventilate the mine configured in a blowing arrangement. Following the ventilation survey airflow quantity, frictional pressure losses and air psychrometric characteristics have been quantified. An accurate resistance survey has been conducted to calculate the pressure drop with regard to moving cages and skips in the shafts. This paper discusses the benefits of utilizing high accuracy digital pressure transducers and psychrometers in a ?leapfrogging? survey to gather data needed to build the computer ventilation model. Two underground booster fans with VFD are currently idle but available at the mine. The ventilation model has been used to determine the optimal booster fan locations to decrease the overall operating cost by reducing the load carried by the main fans. A leakage study has been conducted to evaluate the effects on the system of additional pressure from a booster fan. The study finally prepares a future ventilation model for the next fifteen years of mine operation and investigates the effect of proposed scenarios.

Feb 27, 2013

By S. Jayson Ripke, Shane Hoff

Cleveland-Cliffs’ Northshore Mining Company operates a magnetic iron ore (taconite) concentrator and pelletizer in Silver Bay, MN. These are two recent cost reduction projects: 1. Rougher Magnetic Separators were upgraded throughout the concentrator; throughput and recovery were simultaneously improved. 2. Green Ball Roll Screens on one agglomeration circuit were upgraded from 3.5-inch to 2.5-inch rolls. Throughput improved by 24% from 62 to 77 LTPH. Green ball size distribution improved as an added benefit.

Jan 1, 2005

By Kenneth N. Han, Peter Nam-soo Kim

A kinetic model for leaching of particulate metals in a batch system has been developed. The leaching mechanism has been analyzed by solving a series of ordinary differential equations relating heterogeneous reaction kinetics at the solid/liquid interface to mass transfer of reactant and products. Special emphasis has been given to the effect of changing of the surface area of the leaching substrate and initial particle distribution on the overall leaching rate. The dissolution of gold powders in acidic solution with bromine as an oxidant has been used as a model system. The effect of particle size, chemical reaction order, rate constant and mass transfer coefficient on the overall rate of dissolution of metal powder has been analyzed and discussed.

Jan 1, 2005

By Tom Martin

Mega projects present unique challenges with regard to estimating costs. With such projects, which may span decades, these challenges often begin as soon as a project is conceived. The importance of having a sound, resource based estimate avail-able early in the process cannot be overstated because it provides the basis for ongoing project decisions. For the final phase of providing an updated cost estimate, often while bidding by contractors is underway, the Engineer?s Estimate (EE) must incorporate present market conditions; account for possible volatile material price swings; be based on actual labor and fringe costs; rely on meaningful productivity rates; and accommodate any recent technology advances while identifying and allowing for risk factors. This paper explains the benefits associated with consultants adopting a contractor?s estimating approach when preparing the Engineer?s Estimate on mega projects like the various tunneling projects in New York City.

By B. J. Arnold, N. Terblanche

The features of the ‘Turbo’ froth flotation column will be discussed, including the double aeration system that improves flotation yield while not sacrificing grade, the internal launder system, and the unique feed/tailings sump that evens out flow to the flotation column preventing upset conditions. Results from various test programs and installations will be presented.

Jan 1, 2001

By R. Thornton

Montana Tech is located in the historic mining town of Butte, MT and is adjacent to the Orphan Boy mine. This abandoned underground mine will be the heat source for a down-hole heat exchanger (DHE)/heat pump system. The mine was abandoned in the 1950?s and has since filled with water to within approximately 30 m of the surface. The shaft is composed of a 245 m vertical shaft connected with horizontal crosscut drifts at 60 m and 150 m below the water level that connect to a large stope with approximately 1250 million liters of water at a consistent 75-78°F temperature. The intent is to build this heating system to augment or fully heat a newly built 2,000 m2 building on the Montana Tech campus. As designed the system uses ?off-the-shelf? parts making the basic configuration straightforward with the exception of the DHE?s which need to be placed into the vertical shaft. Because there is little or no examples of placing the heat exchangers in a vertical shaft, the primary focus of this work was to model the heat exchanger placement and configuration in the vertical shaft such that thermal currents develop between the stope and vertical shaft in, via the horizontal crosscut drifts, in order to move the water and thereby provide the required energy. This study includes the modeling of water flow, temperature profiles, and the heat contribution from the surrounding rock walls.

Feb 27, 2013

By Michael Amick, G. Swan, R. Hill, C. Pritchard

Falconbridge, a major base metal producer in the Sudbury Basin of Ontario, identified a need to find a safe and cost effective replacement for welded-wire mesh used to support loose ground during underground nickel mining. Falconbridge took a methodical approach to the concept of a spray-on liner as a screen replacement proving the strength characteristics of the liner as a safe, cost effective, and suitable method of supporting ground. Compact, hydraulic mixing and spraying equipment have been developed and are in use at the Fraser mine. The Tekflex material has been approved as a wire-mesh replacement and has been in use since November1998.

Jan 1, 2000