Search Documents

By M. Dworzanowski

The beneficiation of fine iron ore will increase in importance in the future because most new iron ore resources will be in the form of lower grade ore deposits that will require liberation of iron ore minerals at finer sizes. Generally this fine iron ore will be beneficiated to produce a pelletizing concentrate with very strict chemical and physical specifications. In addition, because of the increasing demand for iron ore there are now more opportunities to produce by-product iron ore from mining operations producing other commodities. In the past the associated iron ore minerals would report to final tailings but now there is potential value to be realised from by-product revenue. These by-product iron ore opportunities are almost all centred on producing pelletizing concentrate. Currently pelletizing concentrates are produced mainly by various combinations of flotation and magnetic separation. The selection of the beneficiation route will depend on ore mineralogy and considerations around plant capacity and final concentrate quality. The main economic iron minerals are magnetic, haematite being paramagnetic and magnetite being ferromagnetic. This, therefore, means that magnetic separation can be applied, in principle, to all fine iron-ore beneficiation plants. While flotation has a considerable capacity advantage over magnetic separation, the real advantage of magnetic separation over flotation in fine iron-ore beneficiation is that treatment of -10 µm iron ore is possible-in flotation, the feed is deslimed at 10 µm and the -10 µm stream is considered to be final tailings, even though there is often a significant amount of contained iron ore. This paper describes a study around the recovery of fine magnetite in the form of a pelletizing concentrate. The study is based on an evaluation of an iron ore by-product opportunity from an iron oxide copper-gold (IOCG) deposit. Experiments were conducted to quantify the differences in magnetic separation performance with decrease in particle size treated. A mineralogical evaluation of all the test work products was undertaken to facilitate the interpretation of the test work results. These results were then used to propose an economically viable flowsheet for maximizing fine magnetite recovery using magnetic separation.

Jan 1, 2012

By J. A. de Carvalho Junior

This paper analyses the impact of the uncertainty associated with the input parameters in a mine planning optimization model. A real example was considered to aid in the building of a mathematical model that represents the coal production process with reference to the mining, processing, and marketing of coal. This model was optimized using the linear programming concept whereby the best solution was perturbed by the stochastic behaviuor of one of the main parameters involved in the production process. The analysis of the results obtained permitted an evaluation of the risk associated with the best solution due to the uncertainty in the input parameters.

Jan 1, 2012

By Q. P. Campbell

The high final total moisture content of fine coal after mining and processing is one of the major reasons that this resource is not extensively used in subsequent power generation, combustion, or other conversion processes. Some coal products, like export coal, may be subjected to a variety of environmental conditions during transport and storage, such as temperature and humidity. To understand the mechanisms by which moisture is attracted and held on and within fine coal particles, further information is needed regarding the processes occurring at the coal surface. In order to determine the correlation between physical coal properties and its moisture adsorption and desorption characteristics, a series of sorption experiments were conducted on various coal samples under climatically controlled conditions. Equilibrium moisture data was collected while changing the temperature and humidity. This data was correlated to coal properties such as particle size, porosity, maceral composition, and mineral content. All the coals that were studied were medium-rank bituminous coals. It was found that the best predictors for moisture adsorption and desorption were the mineral and inertinite contents. Keywords moisture, adsorption, desorption, fine coal, surface properties.

Nov 1, 2013

By R. Abela

In over ninety per cent of mineral sand plants, the most commonly used equipment is the spiral concentrator. The tonnage treated over typical spiral plants can range from as low as 200 ton per hour up to 6 000 tons per hour. Due to the limited capacity of each spiral, plants consist of multiple spirals assembled into banks. The mixture of minerals present in the sand feed requires several spiral stages to achieve the desired mineral recovery. Due to the complexity of the spiral circuits, there are always some design and operating problems that present themselves in plants. These range from slurry distribution, spirals operating at incorrect design parameters and feed variations. The material being treated is difficult to maintain in suspension due to its high density, resulting in segregation and preferential flow in pipelines, distributors and sumps. The objective of this paper is to highlight common problems associated with spiral installations to designers and operators of plants. Practical solutions are recommended in order to prevent and minimize these mistakes in the design. These solutions may be used to improve performance on operating plants.

Jan 1, 2003

By M. Mabuza

Two Rivers Platinum Mine (TRP) is a 55:45 joint venture between African Rainbow Minerals and Impala Platinum, respectively. TRP is situated on the farm Dwarsrivier 372KT, in the southern sector of the eastern limb of the Bushveld Complex. Dwarsrivier is underlain by rock formations of the Critical Zone (Winterveld norite-anorthosite) and the Main Zone (Winnarshoek norite- anorthosite). Two economically significant PGE-bearing layers namely the Merensky Reef and the UG2 chromitite are found within the upper Critical Zone. These are approximately 140 m vertically apart, separated by a series of barren norites and anorthosites. At Two Rivers Platinum, only the UG2 chromitite layer is currently being mined for PGEs. The UG2 sub-outcrops north/south along the Klein Dwarsrivier river valley with a very gentle dip to the west of 7º?10º. At Two Rivers the UG2 averages about 120 cm in thickness, overlain by a waste pyroxenite parting about 20 cm thick, above which is a leader seam about 20 cm in thickness. The mineable cut consists of the leader seam, the waste pyroxenite parting, the UG2 chromitite layer including 25 cm of pegmatoidal pyroxenite footwall, below the UG2 reef to a minimum of 185 cm trackless mining cut. The mining method is a mechanized bord and pillar layout, which will yield a total of 185 000 tons at full run of mine production from the underground UG2 mine.

Jan 1, 2007

By G. M. Dowo

The widespread environmental damage caused by slimes dam construction requires rehabilitation as one of the key management strategies towards land restoration. From the time when Mhangura Copper Mine in Zimbabwe was shut down in 2000 due to viability problems, no follow-up studies were carried out on the slimes dams to assess their development with respect to ecosystem function and longterm recovery. The ecosystem function analysis (EFA) method was thus employed to achieve this end. EFA is a monitoring procedure that establishes how well an ecosystem functions as a biophysical system through the use of rapidly assessed field indicators. The field procedure makes use of simple visual indicators that are related to various soil surface processes. Conventional sampling methods are used to collect the vegetation data. The data was first analysed using landscape function analysis (LFA) software packages and then with various multivariate statistical techniques. In total 27 species were recorded from 14 families; 21 of them occurring in the acacia woodland and only 8 on the slimes dams. Hyparrhenia sp. was the dominant grass on Dam 5 and Imperata cylindrica dominated Dam 6. Acacia saligna was the most abundant tree species on the dams. The tree layer on the slimes dams was not as developed as the grass layer. The rehabilitated slimes dams converged with the natural woodland for the LFA indices of stability, nutrient cycling, and infiltration, which suggested a high level of functionality. The main factors affecting the sustainability of the rehabilitation are postulated to be fire, grazing, and tree harvesting. The study contributed to the importance of, and methods used for, assessing ecosystem function on rehabilitated slimes dams in Zimbabwe, which are often ignored as most efforts focus on the establishment of vegetation on the dams. Keywords ecosystem function analysis, EFA, mine tailings, rehabilitation, monitoring, Mhangura Copper Mine, ecosystem function.

Dec 1, 2013

By P. R. Brenchley

Main ore pass systems should last the life of a mine, and too often expensive and hazardous remedial measures are required to repair a damaged ore pass in an attempt to extend its life. In order to maximize the life expectancy of all ore passes at Moab Khotsong, ?wearing blocks? and ?softer support? systems, combined with basic rock engineering principles, have been implemented. Failure of an ore pass can have severe financial implications, both indirectly because the ore pass cannot deliver the broken rock either from level to level or directly in the shaft ore pass system to the required level for tramming to take place, and directly due to the cost of the repair work that is required. Several factors need to betaken into consideration so that production interruptions are eliminated or minimized. Investigations of damaged ore passes at Moab Khotsong and surrounding mines revealed some interesting mechanisms of damage, and some innovative methods of reducing or eliminating the damage have been implemented at Moab Khotsong. The system design was based on 30 years, experience in main shaft rock passes. The design was to counteract scaling, hang-ups and dust problems associated with main rock passes, and the objective was to increase the life of rockpasses. These problems, including the initial design aspects to try and eliminate the repair measures, are discussed in detail.

Jan 1, 2006

By J. -W. Kim, Y. -B. Kang, H. -G. Lee

The effect of SiO2addition on the decomposition of Li2CO3was investigated at temperatures up to 1000ºC. It was found that addition of SiO2greatly enhanced the decomposition of Li2CO3. The main decomposition reaction started at around 600ºC, and completed just above the melting point of Li2CO3. The major decomposition product was Li2O?SiO2irrespective of the Li2CO3to SiO2mixing ratio while both reactants were available. It was ascertained that a liquid layer betweenLi2CO3and SiO2particles formed and facilitated the decomposition reaction. The governing reaction of the decomposition was the one between the dissolved Li2CO3and SiO2in the liquid layer to form Li2O?SiO2. The decomposition rate was independent of the Li2CO3/SiO2mixingratio until either one had been completely exhausted. When excess Li2CO3existed, it further reacted with the initial product of Li2O?SiO2to form 2Li2O?SiO2. When SiO2was found in excess, on the other hand, no further reaction took place. This is attributed to the fact that uponLi2CO3exhaustion there is no liquid phase available to facilitate further reaction. The apparent activation energy of the decomposition of Li2CO3in existence with SiO2is 198 kJ mol-1.

Jan 1, 2004

This paper reviews the history of refractory materials, highlights the development of refractory technology over the years, draws attention to the technology behind these materials, and comments on future developments in this field. By walking the path with refractory materials, from their initial uses in BC times, to the composite materials that are used nowadays, and the nanotechnology developments that are currently taking place in this field, the reader will come to agree that refractory materials are indeed very ?cool?! Keywords: refractory materials; bricks; monolithic materials.

Jan 1, 2008

By R. Armstrong

Due to limited available level ground, Nkomati Nickel Mine cut a weathered rock slope at the base of a mountain spur in order to create a platform for construction of the primary crusher plant and run-of-mine stockpiles. As space is limited around the mining area, ore processing at Nkomati is based on a high reliability of flow of material through the crusher plant, with minimal usage of other and larger designed stockpiles. Evidently, any crusher plant shutdown will render the mine as a whole unproductive and put excessive strain on the medium- to long-term large ore stockpiles, the deposition rates for which are restricted by founding material consolidation requirements. At the onset of the 2012 rainy season, movement was identified on the slope monitoring system and cracks developed on the slope. After a minor failure on the crusher slope an assessment of the slope stability was conducted and a slope management plan recommended, which included deployment of real-time monitoring. An evaluation of the conditions leading to instability was conducted and the likely causes for the failure identified. A full evaluation of the slope monitoring, rainfall, and mining conditions was undertaken and movement triggers were determined. This paper describes the events leading to the development of the failure and the evaluation of the monitoring data to determine a management plan for the failure that allowed for minimal shutdowns of the primary crusher.

Jan 1, 2014

By J. Kortnik

Mining has always been, and still is, an activity which is vital for the development of mankind. This is because a predominant proportion of industrial products and energy is produced from raw materials that are excavated using mining methods. The need for environmental protection and the close proximity of urban settlements and mines in Slovenia have necessitated ever stricter requirements for the excavation of raw materials and introduction of more environmentally-friendly mining methods. This is achieved by implementing a closed eco-technological cycle of raw material excavation within the scope of mining methods. In surface mines, this means prompt reclamation of the degraded surfaces, and in underground mines the use of methods with minimized impact on the surface and on underground water. In underground mines, mining methods with backfilling installed according to the multi-barrier disposal system are the only ones that allow the possibility of implementing a closed eco-technological cycle of excavating raw materials. Various industrial waste materials are also included in the backfilling material in order to improve its strength properties. Backfilling consisting of several different waste materials is produced in the form of a composite. Before backfilling consisting of waste material composites can even begin to be used in mines, an environmental impact assessment of its suitability for mines needs to be made. In order to make such an assessment, a pressure leaching cell and an open diffusion cell were made, i.e. a pressure leachate test and a sorption test were developed. The two cells and the developed tests will enable the study of the influence of backfilling on the environment if installed in an underground mine. The pressure leachate test performed with the use of the pressure leaching cell simulates leaching from a consolidated backfill during the seeping of underground water into the backfilling material under pressure. The sorption test performed in an open diffusion cell simulates the flow of eluate leached from the backfilling material through the rock/geotechnical barrier. The two tests were developed in such a manner that they are performed either in succession immediately after one another, but they can also be performed separately at a certain time interval. The paper presents an assessment of the suitability of backfilling made of different waste material composites. Keywords: environmental impact assessment, multi-barrier disposal system, waste material composites, pressure leachate test, sorption test, pressure leaching cell, open diffusion cell, eco-technological cycle, mining methods with backfilling.

Jan 1, 2003

By S. P. Pereira

The mechanized mining cycle using loaders and shuttle cars had it speak in terms of usage in the mining industry during 1950 through 1960. In Brazil, this system is still used at underground coal mines in southern Santa Catarina coal basin. With the aim of investigating the benefits of a new mining scheme using the room and pillar method for these local mines, a computational simulator model was developed in order to investigate the mining cycle. This paper presents the methodology used to develop the simulator and the results that the simulation shows regarding impact of the proposed new scheme on mining productivity.

Jan 1, 2012

By D. Grabowski, Z. Pokryszka

ABSTRACT: Some residential areas of the iron basin of Lorraine (in the North-East of France) are affected by noxious gas emissions (under oxygenated, carbon dioxide loaded and radon loaded gas mixtures). Site investigations showed that the gas flow was mainly due to natural thermal air circulation between old mines and the external atmosphere. The main hazards associated with this flow of gas and its potential accumulation in confined volumes within buildings are asphyxiation and intoxication. A further study is in progress in order to better understand the origin of the gas generation within the old iron mine workings. Following the first hypothesis, the carbon dioxide emission is mainly due to the specific hydro-geo-chemical process associating the pyrite oxidation with the acid dissolution of carbonates. KEY-WORDS : gas, emission, mine, flow, pyrite. ZUSAMMENFASSUNG: Einige Wohngebiete der Eisenmulde Lothringen (im Nordöst Frankreich) werden von Ausgasung gesundsheitsschädlichen sauerstoffarmen Mischungen, die mit Kohlendioxid und Radon beladen sind, betroffen. Untersuchungen am Ort haben gezeigt, wie diese Gasstroemung von natürlichem thermischen Luftumlauf zwischen den alten Bergwerken und der externen Atmosphäre ausgelöst wird. Erstickung und Vergiftung sind die wichtigste Risiken, die mit dieser Gasströmung und ihrer möglichen Speicherung in begrenzten Lokalen zusammenhängen. Eine weitere Untersuchung wird durchgefuehrt so dass man die Herkunft der Gaserzeugung in den alten Grubenräume besser versteht. Der ersten Hypothese folgend, Ausgasung von Kohlensäure liegt vor allem an dem hydro-geo-chemischen Prozess, der Pyritrösten mit der säuren Auflösung von Karbonate verbindet SCHLÜSSELWÖRTER: Gas, Ausgasung, Bergwerk, Strömung, Pyrit RESUME: Certaines agglomérations du bassin ferrifère lorrain (au Nord-Est de la France) sont affectées par des émanations de mélanges gazeux sous-oxygénés et chargés en certains gaz nocifs (dioxyde de carbone, radon…). Les investigations effectuées in situ ont montré que les écoulements gazeux à l’origine de ces émanations sont liées au phénomène de tirage naturel entre les anciens travaux miniers et la surface. Les principaux risques engendrés par ces émanations de gaz et son accumulation possible dans des endroits confinés sont l’asphyxie et l’intoxication. Une étude est en cours afin d’expliquer l’origine de la modification de l’air au sein des vieux travaux miniers. Les émissions de dioxyde de carbone seraient dues à des processus hydro-geo-chimiques associant l’oxydation de la pyrite et la dissolution de carbonates. MOTS CLES: gaz, émanation, mine, écoulement, pyrite.

Jan 1, 2003

By E. J. M. Jahnsen, I. Jauhari, T. Badrujaman, F. A. Stober, B. O. Wasmund, L. R. Nelson, T. Miraza, J. M. A. Geldenhuis, A. Taofik Hidyat

The role of dedicated operational support in the ramp-up and stabilisation of the FeNi-II furnace for ferro-nickel production at PT Antam?s smelter located in Pomalaa, Indonesia is described. The furnace was uprated to 32MW capability in a rebuild performed in 2005. This primarily involved installing a larger transformer, coupled with adoption of HATCH water-cooled copper plate, waffle and flanker coolers with integrated metal and slag tapblocks, HATCH air-cooled copper fin lower sidewall cooling and HATCH vertical sidewall binding system ? ?holddowns?. Following a smooth commissioning period, the progress in attaining the preliminary ramp-up target load of 24MW is described. This initial target was set by Antam, subject to some prevailing smelter equipment constraints, particularly kiln capacity. Stabilisation of the furnace operation is discussed, together with some of the specific commissioning and operational challenges surmounted by the joint Antam-HATCH team. These included: ?Mastering furnace integrity monitoring and operation with copper coolers, especially metal tapblock planned maintenance and repair strategies; ?Transition from traditional ?immersed electrode? to ?brush-arc? mode of operation approaching as closely as possible to the productive ?shielded-arc? mode of operation within existing equipment constraints; ?Reductant selection and control issues; ?Utilising the sophisticated furnace monitoring to provide detailed indication and warning of potentially destructive furnace upset conditions such as Si reversion and CO boils.

Jan 1, 2007

By W. H. Van Niekerk

The metal zinc has been around since only about 1400 AD. This may sound like a long time, but when compared to fellow base metals copper and lead, which were discovered in 5000 and 4000 BC respectively, it is evident that zinc is a fairly new kid on the block. This may also be the reason why many new facts and benefits of zinc are still being discovered. For instance, it has been discovered only in the last few decades that virtually no life on earth is possible without zinc. In this address it will be shown that zinc is not only very useful to mankind, but is in fact vitally important for all forms of life. It will be shown that zinc is natural, zinc is essential for life, zinc protects, zinc contributes to the well-being of society and that zinc is fully recyclable. It is therefore hoped, that by the end of this address, zinc will no longer be viewed only as the metal that is responsible for the nice colour of roofing sheets and steel buckets, but may indeed be man?s best friend.

Jan 1, 2005

By M. S. Raseroka

An experimental rig has been constructed to produce chloride stress corrosion cracks in Type 304L stainless steel tube samples. The samples are to be used to test possible in situ repair methods in future work. The factor which influences the time to failure most strongly is the sample temperature; the distribution of cracks within the sample is affected by local temperature variations and by the position of the water line. Low-frequency oscillations in stress, caused by the on-off temperature controller, did not appear to influence cracking in these tests.

Jan 1, 2009

This paper provides a review of the chemical reactions occurring in the submerged arc processing of chromite ores. The excavations of industrial furnaces have shown that the charge, as it descends through the furnace, passes through a number of distinct reaction zones. Each zone is characterised by differing process conditions and reaction products. The phase equilibria, reaction steps and mechanisms occurring as the charge progresses through the furnace are examined, and the potential influences of these factors on the process outcomes are discussed.

Jan 1, 2004

By S. P. Pereira

The mechanized mining cycle using loaders and shuttle cars had its peak in terms of usage in the mining industry during 1950 through 1960. In Brazil, this system is still used at underground coal mines in southern Santa Catarina coal basin. With the aim of investigating the benefits of a new mining scheme using the room and pillar method for these local mines, a computational simulator model was developed in order to investigate the mining cycle. This paper presents the methodology used to develop the simulator and the results that the simulation shows regarding impact of the proposed new scheme on mining productivity.

Jan 1, 2012

By L. Rademeyer, P. Mazzoni, C. Kubank, F. Brown

The Corridor Sands deposits of heavy mineral sands represent the largest known economic resource of titanium dioxide minerals. The West Block of Deposit 1 alone contains Measured and Indicated Mineral Resources of 1.7 billion tonnes containing 4.14 per cent ilmenite, estimated in accordance with the JORC standard, sufficient for at least the first 20 years of mining. Total mineral resources are estimated to be approximately 17 billion tonnes at 5 per cent Total Heavy Minerals (THM). Test work was undertaken on the West Block of Deposit 1 over a period of two years in order to develop the process flow sheet to bankable standards. Geological, mineralogical and metallurgical test work was integrated from a pre-feasibility stage to the full bankable stage. The process flowsheet was developed with the central objective of the production of saleable products, of consistent quality and acceptable to the respective end-markets. The aim of this paper is to describe the way in which the various challenges for the project have been addressed by using integrated geological and mineralogical information, which has resulted in the development of a complete flow sheet. The process confirmed that material within customer specifications could be produced, once various metallurgical parameters were understood. This flow sheet development progressed from laboratory test work through to full field trials at pilot plant scale on large consignments of mineralized material. The flow sheet was developed to such a standard as to be used with confidence for both engineering design and cost estimates, and to determine the recovery factors to be used in financial evaluations. Keywords: Corridor sands, Flow sheet, Pilot plant Titanium dioxide

Jan 1, 2003

By F. M. C. C. Vieira

The DEEPMINE Research Programme sought to develop the technology and competence to mine gold safely and profitably at depths of 3 to 5 km. Among the many issues addressed was the stability and support of rockpasses at ultra-depth. It was found that high virgin and mining-induced stresses could cause the walls of rockpasses to spall, leading to the deterioration and failure. A comprehensive programme of numerical modelling was conducted to investigate alternative mining layouts and sequences to ameliorate the problem.

Jan 1, 2005