Search Documents

By K. M. Banks

The hot ductility of in situ melted tensile specimens of micro-alloyed steels having C contents in the range 0.12?0.17% (mass %) have been examined over the 700?1000°C temperature range. An improved testing method for simulating the continuous casting process was used, which takes into account both primary and secondary cooling conditions. Increasing the N content to electric arc furnace levels (0.01% N) was found to cause a serious deterioration in ductility. V-N steel gave better ductility than Nb-containing steels due to less precipitation. From a cracking perspective, low- N steels are generally recommended but, when not feasible, a combination of Nb and V gives even better ductility. However, to be sure of avoiding transverse cracking in higher N steels a small addition of Ti is required. This resulted in a decrease in the fraction of fine particles and in accord with this better ductility. Transverse cracking of industrial slabs was then avoided.

Jan 1, 2011

By L. Chanderman, C. E. Dohm

"Mineral Resource estimation (MRE) and classification are highly dependent on the confidence in the model of the orebody geometry, known as the geological model, within which the estimates are constrained. An understanding of the geology of a deposit is thus fundamental to the Mineral Resource evaluation process. The geological model is a function of the structural and depositional complexity of the geology captured by drilling information, which is limited in the early stages of a project. The information effect has a significant impact in terms of the interpretation of the geology as well as the estimation of grade continuity and the resultant risk associated with the Mineral Resource estimate and classification.Therefore, as new drilling information becomes available, it is necessary to update and refine the geological model to appropriately constrain the resource estimates. The grade information is also updated, including statistics and the spatial correlation characteristics. This refinement is based on geological interpretations derived from the drillhole information that becomes available throughout the life of the mine; orebody knowledge that comes from working experience of the deposit, as well as familiarity with the software package used for modelling, is also important.In updating, the potential to identify new resources in previously unknown areas may be realized. The opposite may also occur where previous interpretations of ore continuity are refuted. Both scenarios could result from a better understanding of the geology of the deposit and thus a more realistic MRE, which reduces geological risk. This paper describes how newly drilled advanced grade-control holes for a gold deposit in Mali were used to refine the 3D geological model for the deposit in an attempt to identify the potential for additional oxide ore using conventional geostatistical evaluation techniques."

Jan 1, 2017

By J. O. Marsden

The copper industry is cyclical with the price determined by market forces (i.e. the balance between supply and demand for the metal.) The period of each cycle typically varies between 6 to 9 years. These cycles drive decision making for exploration, new project and mine development, mine closures, process improvement, research and development, and technological innovation. The gold industry is fundamentally different from copper in that supply and demand do not, alone, determine metal price and many other factors play a key role, including global and regional financial conditions, political stability, and the global future economic outlook. However, the gold price experiences trends and longer term cycles that similarly drive business decision making. This paper examines developments in the copper industry that have occurred over the past few price cycles (approximately 20 years) and explores how the lessons learned can be applied to gold extraction. A number of specific examples and opportunities are discussed in detail, including; technology development and innovation, cost control and business improvement, material characterization, comminution equipment, biological heap leaching, and concentrate pressure leaching.

Jan 1, 2009

By H. Moslemi

Metal sulphides are usually semiconductor and their electrical conductivity is low; therefore they are sources of electrons and promote electrochemical reactions. This phenomenon is of significant importance in sulphide flotation. The formation of a hydrophobic surface on the sulphide minerals is the result of various electrochemical reactions. Potential difference in the mineral-liquid interface plays an important role in the kinetics of the reactions, and consequently, on the flotation behaviour of sulphides. The value of the potential difference is influenced by different oxidation-reduction reactions at the interface area, and is measured by a two-electrode system in which an electrode is applied as reference electrode. In this study, we attempted to measure open-circuit potentials of pyrite, pyrrhotite, and steel electrodes with respect to the reference electrode. To verify the results, two reference electrodes, saturated calomel and gold, were used. Time-potential relations with respect to both reference electrodes show that the potential of both pyrite and pyrrhotite increases with time; however, this trend decreases for steel except when at pH 12. The results show a potential drop by an increase in pH value, except for steel, for which the opposite holds. This paper discusses galvanic interactions between minerals and grinding media in the grinding circuits, as well as among other minerals in the flotation processes.

Jan 1, 2012

By M. H. Dehghanpoor, M. Zivdar, M. Torabi

"A hydrometallurgical route was developed to extract metals such as gold, silver, copper, and selenium from anode slime from Sarcheshmeh Copper Complex in Iran. For the extraction of copper by leaching, the anode slime was heated and stirred with 4 M sulphuric acid in the presence of oxygen. Optimal conditions for recovery of copper were temperature 80°C, mixing time 5 hours, and oxygen flow rate 2 L/min, resulting in a copper recovery of 94.47%. Silver and selenium were dissolved by leaching anode slime from which the copper had been removed with nitric acid. For gold extraction, anode slime was heated with aqua regia at 90°, and the gold then extracted with 2-ethyl-hexanol at a concentration of 0.5 M and phase ratio of 4. The extract was then stripped with soda solution at pH=10.5 and a phase ratio of 5. Finally, gold was recovered by precipitation with oxalic acid at a ratio of mass to volume 10 g/L. Total gold recovery was 80%. IntroductionDuring the electrorefining of copper, some metals are accumulated in the byproduct anode slime, which is an important source for recycling and recovery of these metals (Petkova, 1994). In this paper, a hydrometallurgical route is described for the recovery of precious metals from copper anode slime of Sarcheshmeh Copper Complex, which is located in southeastern Iran .Copper anode slime is black or gray powder with a particle size less than 200 mesh. Approximately 2 to 20 kg of anode slime is produced per ton of copper cathode. The slime is characterized by higher amount of Ag, Se, Pb, and Cu compared to other metals and a very low Au content (Khaleghi and Ghader, 2013).The copper anode slimes are composed of 11.69% selenium, 3.93% copper, 5.26% silver, 0.13% gold, and 45% barite, plus lead, tellurium, antimony, sulphur, and silica with small amounts of nickel, iron, zinc, and bismuth. Gold is one of the most important noble metals due to its wide applications in industry and economic importance, so recovery of gold from slime is more appealing than that of other metals. According to the World Gold Council (2013), the demand for gold has increased during the last decade. This increase is due not only to the increasing demands of the jewellery market, but also to the increasing demand for gold in industrial as well as medical applications (Ranjbar et al., 2014)."

Jan 1, 2016

The November General Meeting of the Branch was held at the S1. Helena Club on Friday, 15th November, 1968. Mr. J. G. Kirchner (Chairman of the O.F.S. Branch) was in the chair. There were also present: President: Mr R. C. J. Goode. Eighteen Members: Mr A. E. Gilfillan (Council Member), Messrs T. Zadkin, J. N. Saunders, N. A. Honnet, D. D. Waterman, C. R. Netscher, (Committee Members), Messrs G. Thorburn, Z. Lombard, H. V. Henwood, C. J. Isaac, S. L. S. Swart, J. D. McNamara, H. H. Schellhorn, J. W. Wilson, G. C. P. Labuschagne, L. J. Thorne, R. C. Espley-Jones, J. Handley. Seventeen Associate Members: Messrs H. J. Reeders, R. Campbell, P. A. Hoffman, D. E. Couperthwaite, M. D. de Lange, G. J. C. Young, G. W. Futcher, U. Visser, F. H. De Groot, E. Schmid, K. G. Pearce, D. A. Viljoen, H. W. M. Eschenburg, R. Still, W. B. Howe, A. H. Edwards, R. H. Drake. Three Graduates: Messrs T. R. Stromsoe, J. G. Cockburn, T. A. Ward. One Affiliate: Mr O. A. Huss. Twenty-three visitors. Total present: 64. Apologies were reseived from Messrs L. O. W. Leimer, V. C. Barnes and A. Louw. WELCOME TO VISITORS The Chairman declared the meeting open and extended a special welcome to the following: Mr R. C. J. Goode, President of the S.A. Institute of Mining and Metallurgy; Mr A. E. Gilfillan, Member of Council and Mr D. A. Viljoen, all from Johannesburg. Also to Mr J. D. McNamara, the guest speaker for the evening who had made the trip from Oranjekrag. MINUTES OF PREVIOUS GENERAL MEETINGS The minutes of two meetings, viz., the General Meeting held on 26th June, 1968 together with those of the Annual General Meeting held on 14th August, 1968 were taken as read and their adoption moved by Messrs T. Zadkin and D. D. Waterman. MATTERS ARISING FROM THE MINUTES There were no matters arising from the minutes. ADDRESS BY PRESIDENT OF COUNCIL, MR R. C. J. GOODE With regard to the 75th Anniversary of the Institute, the President called upon those present to bear the following two dates in mind, viz.: 21st March, 1969-Banquet at the Wanderers' Club, to which ladies are invited. 24th March, 1969-General Meeting at Kelvin House at 9.30 a.m., the speakers being the President of the Institute, the President of the Chamber of Mines and Dr H. J. van Eck.

1. New books Australian Institute of International Affairs. Uranium - energy source of the future? Canberra, thelnstitute (Box E181, P.O., Canberra, A.C.T. 2600, Australia), 1979. 202 pp. A$4,95 (postage 50c). Euroeconomics. The steel industry in Western Europe.. industrial and financial indicators. Paris, Eurofinance (9 Avenue Hoche, 75008 Paris, France), 1979. 167 pp. FF4,500 (Available in English and French.) M. B. Piggott. Load-bearing composite materials. Oxford, Pergamon Press, 1979. $15,00. J. H. E. Olaf. Automation and remote monitoring and control in mines. Essen (West Germany), Verlag Gliickauf GmbH, 1979. 200 pp. DM36. (In English.) J. P. Jenkins and E. T. Brown (eds). KWIC index of rock mechanics literature. Oxford, Pergamon, 1979. 742 pp. £60. R. J. Wakeman (ed.). Progress in filtration and separation 1. Amsterdam, Elsevier, 1979. 346 pp. Dfl.llO,OO. 2. New journal As from 1980, Coal Calendar is being published as a separate monthly periodical. 3. Proceedings L. E. St Pierre and G. R. Brown (eds). Future sources of organic raw materials. Oxford, Pergamon, 1979. 612 pp. £22,50. P. Haasen, V. Gerold, and G. Kostorz (eds). Strength of metals and alloys. Oxford, Pergamon, 1979. 3 vols., 1800 pp. $200. K. J. Miller and R. F. Smith (eds). Mechanical behaviour of materials. Oxford, Pergamon, 1979. 3 vols., 1800 pp. U.S.$200. 4. Tax relief? The Publishers' Association of Great Britain recently issued a circular to a number of professional bodies drawing their attention to a court decision in favour of tax allowances on the purchase of textbooks. In January Electroheat The International Union for Electroheat, which com. prises a score of highly industrialized countries, every four years organizes a congress at which experts discuss the technicalities and economics of the latest applications of electroheat in industry and other sectors. Corrigenda: March issue The following amendments should be made to Table II of the paper 'Commodity analysis:

Jan 1, 1980

By K. C. Mills

The objective of this work was to provide process engineers with values of the physical properties of various slag systems involved in high-temperature processes. Software that calculates the thermo-physical properties of slags from chemical composition is available on the www.pyrometallurgy.co.za website. This paper outlines the principles underlying the various models available in the program. The software calculates the following properties of crystalline, glassy, and liquid slags (where appropriate) as a function of temperature: heat capacity, enthalpy, density, viscosity, thermal conductivity, electrical conductivity, and surface tension. We hope, in the future, to update the program to (i) add new models as they become available, (ii) remove any ?bugs? discovered in existing programs, and (iii) provide guidance on the limitations of individual programs.

Jan 1, 2011

By C. G. Goncalves

The Gautrain rapid rail link project is currently Africa?s largest infrastructure project connecting South Africa?s major airport (OR Tambo), Johannesburg and Pretoria. Phase one is planned for completion in time for the 2010 FIFA Soccer World Cup and involves 80 km of track and 15 km of underground tunnels. The key shaft sinking blasting issues revolve around maximising advance and improving blasting cycles to meet the tight deadlines as well as environmental control which, in some cases takes place only 15m from the city infrastructure. To achieve success, DetNet South Africa supplied a range of electronic detonator systems to cater for the different blasting applications involved (tunnels, portals, shafts and viaduct foundations). One such product, QuickShot, was used for the first time in a major civil engineering project and has been used in most of the shaft sinking blasts to date. The QuickShot system combines pre-programmed electronic detonators with special on-bench components that enable the user to quickly and easily design the firing sequence solely by using the order of connections. This precludes the user from having to deal in absolute delay times. The connecting system enables benches to be hooked-up speedily by multiple users who have differing levels of experience. This paper provides details of how, after 33 months, the system has been embraced by the project by aiding in maximised advances, improved cycle times and meeting the required environmental constraints.

Jan 1, 2009

By C. G. Goncalves

The Gautrain rapid rail link project is currently Africa?s largest infrastructure project connecting South Africa?s major airport (OR Tambo), Johannesburg and Pretoria. Phase one is planned for completion in time for the 2010 FIFA Soccer World Cup and involves 80 km of track and 15 km of underground tunnels. The key shaft sinking blasting issues revolve around maximising advance and improving blasting cycles to meet the tight deadlines as well as environmental control which, in some cases takes place only 15m from the city infrastructure. To achieve success, DetNet South Africa supplied a range of electronic detonator systems to cater for the different blasting applications involved (tunnels, portals, shafts and viaduct foundations). One such product, QuickShot, was used for the first time in a major civil engineering project and has been used in most of the shaft sinking blasts to date. The QuickShot system combines pre-programmed electronic detonators with special on-bench components that enable the user to quickly and easily design the firing sequence solely by using the order of connections. This precludes the user from having to deal in absolute delay times. The connecting system enables benches to be hooked-up speedily by multiple users who have differing levels of experience. This paper provides details of how, after 33 months, the system has been embraced by the project by aiding in maximised advances, improved cycle times and meeting the required environmental constraints.

Jan 1, 2009

By C. J. Tonkin

Compressed air is widely used on South African gold mines. However, due to recent and proposed future electricity tariff increases it is quickly becoming too expensive to produce and use. Boxfront chute systems at ore passes were focused on during this study, and a number of alternative power sources were examined. After comparing primarily costs, and secondarily safety and practicality, of a number of systems based on water and hydraulic oil, a system making use of either air or water was determined to be the most cost effective. A payback time of 8 years was calculated, which will be significantly less taking into account the avoidance of failures due to electricity and water shortages, which would not affect this system due to its ability to swap between either air or water. It was recommended that this system be installed at all boxfront chutes as soon as possible so that the company can begin to benefit from the cost savings.

Jan 1, 2013

By G. Blight

As part of an investigation of possible water-saving measures at Anglo American Platinum's Mogalakwena Mine in Limpopo, South Africa, a study was made of conditions on the wet beaches of two adjacent tailings dams, each serving a separate plant on the mine. For one of the dams, a special catamaran was designed and constructed to enable the full length of wet beaches to be accessed and sampled immediately after a layer of tailings had been deposited. For the other dam, the wet beach was accessed using conveyor belting and scaffold planks. The length of the beaches was 400 m on the first dam, and 200 m on the second, and each was sampled at 50 m intervals. The parameters reported in this paper, for both beaches, are: > Water content profiles along each beach from the surface to as deep as 2.5 m, at times ranging from 12 hours to 6 weeks from the end of deposition > Particle size distributions at the surface, down the full length of the beaches > Measurements of feed relative density, tonnage and volume, decant and drain flow volumes, as well as rainfall and evaporation for both dams. The surface water contents shortly after deposition have been used to establish the relative density of the settled, decanted tailings and its variation down the beach. This data, combined with the decant and drainage flows, is used to establish the calculated and actual water recoveries from both dams.

Jan 1, 2012

By A. M. Bauristhene

Ti-64, which accounts for more than 50% of the worldwide titanium tonnage, has found commercial importance in industries requiring components with high specific strength and resistance to corrosion. Investment casting is the preferred production method due to the difficult machinability of the alloy. This study was aimed at investigating the mechanism and the extent of alpha case formation on Ti-64 components cast using the investment casting method with YFSZ (yttria fully-stabilized zirconia) shell moulds after vacuum induction melting. The extent of the reaction between the mould hot face and the molten metal has been studied by varying parameters such as soaking temperature and mould hot face composition, and examining their effects on the reaction with the mould. An increase in the soaking temperature had an effect on the alpha case, both in appearance and hardness, but had no effect on contamination levels by carbon, oxygen, and nitrogen. The depth of alpha case increased with soaking temperature, increasing from 35 µm to 161 µm with an increase in temperature from 1200°C to 1400°C. The micro-hardness profiles provided insight into the effect of the alpha case on the mechanical properties of the Ti-64 alloy by displaying hardness values of 1000 HV0.1 and above, but could not be solely utilized to determine the alpha case penetration depth due to microstructural differences in the unaffected Ti-64, in particular the martensitic microstructure that formed with a fast cooling rate from a higher temperature. Levels of expected contaminants such as Zr, Y, 0, and C were low. The addition of the colloidal zirconia binder affected the interfacial reactions. YFSZ proved to be a thermodynamically stable refractory material, with the alpha case possibly forming as a result of segregation.

Jan 1, 2013

By J. F. Lupo

One of the earliest records of metal recovery by solution leaching is described by Agricola as 'juice of rock' in the 1550s. In these early years of hydrometallurgy and civil engineering, few controls and systems were employed to enhance recovery and protect the environment. Since that time, leaching (dump or heap) operations have made significant strides in increasing metal and solution recovery while protecting the environment, all goals of a sustainable operation. It is now recognized that the design and operation of modern heap leach facilities requires contributions from many fields of study, including hydrometallurgy, civil engineering, geotechnical engineering, unsaturated-flow hydrology, mine planning, geosynthetics engineering, geochemistry, process engineering, mechanical engineering, and electrical engineering. While advancements in these fields have resulted in more sustainable heap leach operations, challenges in the industry still exist. A number of heap leach operations exhibit poor or lower-than-predicted metal recovery, loss of solution flow and control within the ore heap, loss of ore heap stability under leach, failure of liner and/or solution recovery systems, and overtopping of process water ponds. A number of these issues may be the result of several compounding conditions. For example, poor metal recovery may be due to an inadequate scale-up assumption (scaling laboratory tests to field-size heaps), lack of control of the in-heap geochemical environment, changes in ore mineralogy from the original design, changes in mechanical and hydraulic properties of the ore from the original design, ore handling and pre-treatment, inadequate solution management system, and inadequate solution application. The purpose of this paper is to present and discuss issues that may affect the sustainability of a heap leach operation. Since sustainability encompasses a broad range of topics and issues, the focus of this paper will be on issues affecting metal and solution recovery, solution flow and containment, and stability of the ore heap.

Jan 1, 2012

The development of short- and medium-term mine production schedules in isolation from each other has meant that only a local optimum can be achieved when each scheduling phase is carried out. The globally optimal solution, however, can be achieved when integrating scheduling phases and accounting for the interaction between short-term and medium-term activities simultaneously. This paper addresses the task of integrating short- and medium-term production plans by combining the short-term objective of minimizing deviation from targeted mill feed grade with the medium-term objective of maximizing net present value (NPV) into a single mathematical optimization model. A conceptual sublevel stoping operation comprising 30 stopes is used for trialling segregated and integrated scheduling approaches. Segregated medium- and short-term scheduling using separate models achieved an NPV of $42 654 456. The final scheduling approach involved integrating the two scheduling horizons using the newly-developed globally optimal integrated production scheduling model to achieve an NPV of $42 823 657 with smoother mill feed grade. The larger the stope data set, the larger the difference between the two scheduling approaches is likely to be. At the very least, an integrated approach ensures feasibility across the two scheduling horizons, which cannot always be assumed when using a segregated approach.

Jan 1, 2012

By C. Montoya

This paper shows, through a case study, the impact of multivariate grade modelling upon mine design and mine planning. A deposit explored by drill holes is considered, in which the grades of five elements (copper, silver, molybdenum, arsenic, and antimony) are of interest. Forty alternative models of the deposit are constructed by fitting the joint correlation structure of the grade variables and using conditional cosimulation. In addition, a reference model, obtained by averaging the alternative models, is also considered. The study shows that the resulting mine design (final pit characteristics and production schedules) is sensitive to the grade model under consideration, and that the design based on the reference model may not be optimal when compared to the alternative models based on cosimulation. However, when assuming a given long-term plan and extraction sequence, the grades and net present value (NPV) calculated on the reference model are unbiased with respect to those calculated on the alternative models with the same extraction sequence. The latter allow assessing the possible dispersion of the actual grades and NPV around their expected values, and are useful for the planner in order to determine the probability of meeting given production targets and of exceeding or falling short of given threshold grades. Additionally, unlike cosimulation, the separate simulation of each grade variable leads to unrealistic resource models and to biased results in mine design and mine planning. This approach should therefore be avoided, unless the grade variables are spatially uncorrelated.

Jan 1, 2012

By M. Cuba

Geostatistical modelling aims at providing unbiased estimates of the grades of elements of economic interest in mining operations, and assessing the associated uncertainty in these resources and reserves. Conventional practice consists of using the data as error-free values and performing the typical steps of data analysis - domaining, semivariogram analysis, and estimation/simulation. However, in many mature deposits, information comes from different drilling campaigns that were sometimes completed decades ago, when little or no quality assurance and quality control (QA/AC) procedures were available. Although this legacy data may have significant sampling errors, it provides valuable information and should be combined with more recent data that has been subject to strict QA/QC procedures. In this paper we show that ignoring the errors associated with sample data considerably underestimates the uncertainty (and consequently the economic risk) associated with a mining project. We also provide a methodology to combine data with different sampling errors, thus preserving the relevant global and local statistics. The method consists of constructing consistent simulated sets of values at the sample locations, in order to reproduce the error of each drilling campaign and the spatial correlation of the grades. It is based on a Gibbs sampler, where at every sample location, the actual sample value (with error) is removed and a conditional distribution is calculated from simulated values at nearby sample locations. A value is drawn from that distribution and kept only if it satisfies some statistical requirements-specifically, the global relative error and local means and variances must be reproduced. All sample locations are visited and simulated sample values are generated iteratively, until the required statistics are satisfactorily attained over all sample locations. This generates one realization of possible sample values, respecting the fact that the actual samples are known to carry an error given by the global relative error. Multiple realizations of simulated sample values can be obtained by repeating the procedure. At the end of this procedure, at every sample location a set of simulated sample values is available that accounts for the imprecision of the information. Furthermore, within each realization, the simulated sample values are consistent with each other, reproducing the spatial continuity and local statistics. These simulated sets of sample values can then be used as input to conventional simulation on a full grid to assess the uncertainty in the final resources over large volumes. The methodology is presented and demonstrated using a synthetic data-set for clarity.

Jan 1, 2012

By S. Tshikhudo

This paper outlines an investigation into the recovery of saleable fractions of coal from ?as-arising? South Export Plant effluent streams, using Baleen microscreening technology. South Export Plant, a subdivision of BHP Billiton Energy Coal SA (BECSA) Coal Processing, is a two-module plant treating 2000 t/h. The nominally -150 µm coal is untreated and is therefore passed from classifying cyclones to the thickeners for process water recovery. The thickened underflow is pumped into a series of slurry cells for further settling and recovery of supernatant water. The marginal quality, moisture content, and handlebility of this settled material renders it unsuitable for inclusion into saleable products and it is thus stockpiled and trucked to designated pits for disposal. Over the years, stockpiling and trucking has become an overly expensive exercise. In an effort to recover some of this cost, a task team was assigned to investigate less costly options to process slurry across BECSA plants. Various technologies such as froth flotation, sieve bends, and Reflux Classifier were considered, although the results were generally not beneficial ? this could be attributed to weathered/oxidized coal. A decision was made to pursue an alternative approach by testing the suitability of the new ?Baleen Filter?. The concept is to screen out the higher-grade fraction (+50 µm) as saleable product and reject the finer fractions to the slurry ponds. The Baleen Filter was found to effectively screen at an acceptable efficiency between 94% and 99.99%, with a very sharp cut-point (d50 and Ep). The actual yields from the screening results were better than the predicted yields in terms of both mass and energy as predicted from feedstock analysis.

Jan 1, 2014

"Coal seam gas problems can adversely affect the safety and productivity of underground coal mines, leading to fatalities and financial losses. Conventional gas management technologies using ventilation and gas drainage are unable to deal with the high and irregular gas emissions associated with high-production longwall mining. New technologies need to be developed to supplement the traditional gas management techniques to minimize the hazard of coal seam gas. Thin spray-on liners (TSLs) have gained some success for rock surface support since their introduction to the mining industry. Due to their relatively low permeability and appropriate mechanical properties, TSLs also show potential to be used as a gas management tool in underground coal mines.In this paper we review the current gas management challenges and discuss the potential use of TSLs as a gas management tool in underground coal mines. This may involve reducing gas migration into the excavations/roadways, enhancing in-seam gas drainage, and preventing spontaneous combustion. Some potential areas for future research work are identified. IntroductionWhen a coal seam is influenced by mining activities, gas stored inside is liberated into the underground ventilation system. Gas emissions have created serious difficulties for the coal mining industry around the world. Therefore, coal mines have to develop effective strategies to control the gas concentration below the threshold value to meet statutory requirements. Ventilation has been the first solution in gas management for underground coal mining. When the emitted gas cannot be effectively diluted by ventilated air, gas drainage using pre- and/or post-drainage has to be introduced. However, even with ventilation and gas drainage, irregular gas emissions usually increase the gas concentration in roadways and slow down the development rate, thus causing significant economic loss to the coal mining industry (Thakur, 2006). Therefore, new technologies need to be developed to address this issue and mitigate the explosion risk."

Jan 1, 2016

By J. H. Viljoen, C. H. Graan, N. B. Strydom, J. S. Greyson

M J Martinson (Fellow) There is everywhere a lamentable dearth of quantitative information on occupational factors affecting the health and safety of mineworkers, and as the authors point out in their introduction underground lighting is one of the factors which has received little attention in South Africa prior to this welcome paper. Since the authors are to some extent pioneering, it is perhaps inevitable that the paper should raise more questions than it answers, but nevertheless it provides a provisional yardstick against which the need for, and success of, remedial action may be judged. Before commenting in detail on a few aspects of the paper it may be worthwhile to summarize the statutory provisions relating to underground lighting, contained in Chapter 15 of the Regulations promulgated in terms of the Mines and Works Act 27 of 1956. Chapter 15 is entitled `Lighting, Safety Lamps and Contraband', but in the context of the present paper only four simple regulations need be noted: firstly, no person shall work or travel in an unilluminated part of a mine unless he carries a light ; secondly, adequate stationary lights shall be provided at stations and certain other localities in shafts, winzes and places used for winding; thirdly, mechanically propelled conveyances shall be provided with an effective bright light shining in the direction of travel; and fourthly, moving machinery to which personnel have access shall be illuminated so as to be clearly visible. In all four regulations the standard of lighting to be provided is wholly subjective, and under these circumstances the wide inter- and intra-mine variations in light intensity disclosed by the study are hardly unexpected. Nevertheless the data presented in the authors' Table I raise three points (1) Is there any evidence that the 19 mines visited during the survey are representative of the 45-50 large gold mines in South Africa, or that the shafts selected are representative of the respective mines? Mine managers would scarcely be human were they not to offer better lit working places for the survey; perhaps the use of a scaling factor (e.g. tonnes or transit mineworkers per shift, kilowatts, etc.) for each working place might have helped to put the figures in perspective. (2) Looking at two of the more numerous - and probably important - of the ten working places included in the survey, i.e. stations and tips, one is struck by the marked. skewness of both intensity distributions (with higher frequencies at the lower intensities) and the abrupt cut-off in both cases just short of pitch darkness. Thus, of the 45 meaned readings recorded at 26 tips no less than 19 fall in the lowest range of 0,1-0,9 1m/ft2, with but one tip in total darkness; of 46 readings on 26 stations, 7 fall in the lowest range and none is in total dark-'1 ness. Although a light with an intensity in the range 0,1-0,9 1m/ft2 may satisfy the regulations, it is certainly arguable that in some situations it may be safer to have no light at all. (3) In view of the skewness referred to above, one wonders how meaningful are the `total average light intensities for (the gold mining) industry' quoted in Table I, which the authors compare with illumina¬tion levels found in other countries. Looking at tips again, one notes that 34 out of 45 meaned intensity readings fall below the `total average' for tips, and only 10 exceed it. From this it may be concluded that a few well-lit working places included in a `total average' may conceal a plethora in Stygian gloom. In their discussion the authors make fleeting reference to the effect of underground lighting on productivity and accident rates, without however quoting any South African experience in this regard. Intuitively it seems highly likely that better lighting (in the widest sense) would improve productivity and reduce accidents, and of course it is in these areas that the mining industry might seek economic justification for providing better lighting. It is all the more regrettable therefore that these factors were not studied simultaneously with the present investigation, especially at the Psychological Division of the Human Sciences Laboratory has recently published a study on underground accidents in the gold mining industry without making any reference whatsoever to lighting as a causal factor. In the event neither of the two studies enables us to make an economic appreciation of the situation, and this seems to be a classic example of a situation where some dovetailing of research effort would have greatly increased the useful return. On the effect of lighting on accidents, it may be noted that in 1939 Mickel presented some very interesting statistics to the Mine Managers Association of the Transvaal2, on the improvement in accident rates which followed the random issue of electric cap lamps to native mineworkers in the Hercules Section of E.R.P.M. the previous year. Based on a 12 month trial period in which 250 000 shifts were worked with carbide lamps and (contemporaneously) 307 000 shifts with cap lamps, the incidence of major accidents (at least one day in hospital among men using carbide lamps was 1,15 accidents per 1000 shifts, while the incidence of minor accidents (requiring dressing only) was 11,52 per 1 000 shifts. The corresponding figures for men using cap lamps were 0,79 and 7,31 accidents per 1 000 shifts respectively, representing a reduction of over 30 per cent in both major and minor accidents. While these figures are obviously dated - only men using cap lamps were issued with hard hats, for instance - they do indicate a need for similar research today.

Jan 1, 1971