Search Documents

By G. P. O’Malley, A. N. Nikoloski

One of the most promising options for extraction of copper from low-grade chalcopyrite ores by heap leaching, however, chalcopyrite is refractory and suffers slow leaching kinetics and poor overall extraction due to formation of a passivation layer on the particles. The solution composition is believed to strongly affect the formation of this layer. This paper examines the effects of the major cationic species of Fe3+/2+, Mg2+, Cu2+, and Al3+ and the anionic SO42− species in acidic ferric sulfate media with a composition simulating recycle heap leach conditions. It was found that altering the sulfate, iron or aluminium concentration had significant effect on the copper extraction, the concentration of copper slightly influenced the extraction, and the amount of magnesium had no appreciable effect. Also, iron and aluminium caused a change in the sulfate concentration, and the sulfate ions had the greatest influence on the extraction of copper under recycle leach conditions

Jan 1, 2023

By P. Linzer, L. M. Linzer

The gravity method is often applied in mining-related scenarios such as geological and mineral exploration, detecting subsurface cavities and voids (“receptacles”) that may become sinkholes, siting of surface structures, fault-mapping, and more. It is also widely applied in geotechnical engineering to map subsurface karst profiles and to detect subsurface cavities, such as can occur in open pit mines. While it is widely acknowledged that, compared with other available geophysical methods, this method is the most applicable to the karst profiling problem, survey geometries applied in the field are often far from optimal. The gravity surveying specifications prescribed in SANS 1936 omit some key requirements for optimal survey outcomes, and this paper is intended to fill those gaps. The authors have seen scopes of work that require only a few measurements over the footprint of a proposed structure, indicating a lack of understanding of the nature of the gravitational field. A single gravity measurement is subject to the camouflaging effects of several influences, many of which can be larger than the anomaly caused by the subsurface density variation itself. Papers in the body of literature show an awareness of the need to map the regional field so that it can be subtracted to unmask the residual gravity anomaly, but rarely do they examine how instrument sensitivity governs the size of detectable anomalies or discuss how a detailed terrain correction can be instrumental for isolating faint targets. This paper aims to explain how to apply the gravity method correctly to mining and geotechnical problems, specifically in the detection of subsurface cavities. It discusses various factors to assist with optimising the acquisition of gravity data and its processing so as to maximise the practical value of gravity surveys.

Sep 1, 2025

By M. H. Moys, J. Engelbrecht, N. Terblanche

Interface levels in flotation columns are generally measured with the aid of a pressure-sensitive Instrument, e.g. a differential-pressure cell. This paper criticizes the use of this type of measurement, and discusses other methods that are claimed to give more accurate measures of interface levels. The paper focuses on the development of methods based on the measurement of conductivity across the froth-slurry interface. These are often sabotaged by variations in the conductivity of the feed slurry, particularly when the pH of the slurry IS being controlled, e.g. In sulphide flotation. Methods of improving the accuracy and reliability of this technique are described. The result IS a robust, easy-to maintain level-control scheme that successfully rejects large disturbances in plant operation (including a 5:1 change in slurry conductivity) while controlling levels to an accuracy of I 4 cm.

Jan 1, 1992

By T. Szendrei, S. Tose

The generally accepted view in rock blasting is that the sources of energy for the fracture and movement of rock reside in the shock wave and gas action resulting from the explosion, and yet the mechanisms by which these sources interact with the rock have remained unclarified. It has also been noted that up to 50% of the work capacity of an explosive released in a blast cannot be accounted for by field measurements of energy partitioning. In this study, we describe a physical model that details the response of rock to both shock wave and gas action. An analytical model based on momentum conservation is derived to describe the dynamics of shock-driven expansion of the blasthole. Radial expansion of the hole is the key parameter that permits the derivation of the following characteristics of rock response to shock loads: hole expansion time; volume of displaced rock; energy consumed per unit volume; expansion energy efficiency; stress wave pulse length; gas pressure in enlarged hole. Soon after the completion of hole expansion, the shock wave degenerates to an elastic stress wave that runs through the burden. Blasthole expansions of between 50% and 300% of diameter are completed in under 1 ms and, depending on rock properties, consume 32% to 42% of the detonation energy or about 55% of the available mechanical (Gurney) energy. Gas pressure in the enlarged holes in five rock types is between 35 MPa and 650 MPa, and drives the mass movement of burden rock.

Oct 9, 2024

By K. Karaman

This study investigated the effect of surface roughness on Schmidt rebound hardness (RL). Four different test surfaces of rock samples were studied: natural, ground, cut surfaces, and core samples. There was significant variability of standard deviation based on the RL on the natural surface, which indicated high roughness of the rock surface, whereas surface polishing caused a significant decrease in standard deviation. ISRM and ASTM methods were compared to estimate unconfined compressive strength (UCS) for different testing surfaces. RL obtained from the cut surface was found to be more reliable than those obtained from other testing surfaces for the prediction of UCS; however, regression and ANOVA analyses revealed that the ISRM method gave a more accurate UCS estimation of rocks with highly rough surfaces. It was also shown that RL values obtained from a cut surface were significantly higher than those obtained from core samples. Therefore, a comparison between RL values obtained from core samples and cut surfaces was made based on previous studies. This study statistically showed that estimated UCS values are not statistically significant if Schmidt rebound tests are not performed on similar surfaces. In addition, the mineral grain sizes of the studied rocks, different testing surfaces compared with those in literature, and standard deviation from RL are evaluated and discussed. The Schmidt hammer technique is a rapid, inexpensive, and straightforward method for estimating UCS for preliminary assessment; however, roughness of the surface should be eliminated if variations are shown in the surface rebound hardness.

Apr 14, 2024

By T. Szendrei, S. Tose

The Gurney approach to explosive/inert material interaction was adapted to analyse the face velocity in bench blasting. The model is based on the blasthole diameter, rock and explosive density, burden, spacing, linear charge density, and the Gurney energy constant. It is validated by comparing its predictions with a set of 20 field measurements of face velocities reported by Chiappetta et al. (1983) in an iron ore mine. The Gurney model links the observed large scatter of measured face velocities to the variation of the Gurney energy constant. This in turn is linked to the variability of the gas pressure acting on the burden. These variable pressures are generated when detonation product gases migrate into the extensive and complex fracture network around and between in-row blastholes. The energy efficiency of burden movement can be derived from the model. It is shown that ~7% of the explosive’s chemical energy is available for gas expansion work on the burden; of this quantity, 36% is actually converted to burden kinetic energy. That is, less than 3% of chemical energy is ultimately expended in burden displacement and throw. The model further indicatesnthat the projection of high-velocity (say, 100 m/s) flyrock is possible only when the path of leastnresistance through the burden has an effective density far less than the host rock. An equationnis derived that identifies the combinations of burden and path density that may yield flyrock. These values are specific to a particular baseline blast design.

Jan 30, 2026

By S. Swanepoel, A. V. Cherkaev, Q. G. Reynolds, M. Erwee

Ferrochrome (FeCr) is a vital ingredient in stainless steel production and is commonly produced by smelting chromite ores in submerged arc furnaces. Silicon (Si) is a componrnt of the FeCr alloy from the smelting process. Being both a contaminant and an indicator of the state of the process, its content needs to be kept within a narrow range. The complex chemistry of the smelting process and interactions between various factors make Si prediction by fundamental models infeasible. A data-driven approach offers an alternative by formulating the model based on historical data. This paper presents a systematic development of a data-driven model for predicting Si content. The model includes dimensionality reduction, regularized linear regression, and a boosting method to reduce the variability of the linear model residuals. It shows a good performance on testing data (R2 = 0.63). The most significant predictors, as determined by linear model analysis and permutation testing, are previous Si content, carbon and titanium in the alloy, calcium oxide in the slag, resistance between electrodes, and electrode slips. Further analysis using thermodynamic data and models, links these predictors to electrode control and slag chemistry. This analysis lays the foundation for implementing Si content control on a ferrochrome smelter.

Mar 14, 2024

The first annual student prizegiving function of the South African Institute of Mining and Metallurgy was held in the Dorothy Susskind Auditorium, University of the Witwatersrand, on Thursday, 26th May, 1977. The address (see opposite page) was given by Dr M. G. Atmore, a director of Anglo American Corporation and Vice-President of the Institute.

Jan 1, 1977

By S. Bradshaw, A. Mabentsela

"Physical and numerical modelling methods were followed to identify mechanism(s) for tundish slag entrainment in a bare tundish and one with a flow control device (FCD).The physical and numerical models made use of water and paraffin to model steel and slag respectively. Observations from the physical model showed that the steel-slag interface remains immobile in both cases. Entrained paraffin formed droplets approximately 1 mm in diameter. Results from both models (numerical and physical) showed that in both cases (bare and FCD case), areas of high entrained slag concentration exist near the inlet region. The entrained slag concentration decreases towards the tundish endwalls.Flow patterns and velocities tangential to the steel-slag interface from the numerical model showed that slag entrainment in both the bare tundish and tundish with a FCD possibly takes place via two mechanisms. First, the slag moves across the steel-slag interface via mass transfer; secondly small velocities tangential to the interface at depths greater than 10 mm below the interface carry the already ‘entrained’ slag into the bulk steel phase. These tangential flow patterns are dominant in the inlet region, hence the high concentration of entrained slag in this region. IntroductionThe tundish serves as the last metallurgical vessel through which steel passes before solidifying in the moulds. It is in the tundish that the last traces of non-metallic inclusions should be removed, otherwise the inclusions carry over to the moulds and cause defects in the steel product. In the tundish, the slag is less dense than the melt and thus resides on the top of the melt. The slag provides a sink into which the non-metallic inclusions float to and dissolve. The slag also protects the melt from air and heat loss. However, when slag is entrained in the melt as a result of increased turbulence or shearing at the steel-slag interface, slag can become a source of nonmetallic inclusions.Numerous studies on flow patterns in the tundish have been carried out since the introduction of the tundish. These studies were aimed at improving the flow characteristics in the tundish (Chattopadhyay, Isac, and Guthri, 2010; Cloete, 2014; Jha, Dash, and Kumar, 2001; Jha, Rao, and Dewan, 2008;"

Jan 1, 2017

"SAMPLING: THE IMPACT ON COSTS AND DECISION MAKING1. INTRODUCTIONFor years those in the minerals industry have been taking samples to assist them in making decisions; whether they be about investing billions of rand in a new mining operation, or simply whether a truck load of mineralised material should go to the mill or the waste dump, - we need a sample to help us make our decisions. This paper emphasises the importance and significance of sampling as a process, some of the associated technical problems and some of the advantages, especially in the light of traditional approaches that has usually left mine sampling to the least educated and lowest paid individuals on the mine. Perhaps the most important aspect that requires attention is the variability, usually measured in terms of precision, that tends to infect the sampling procedures. Francis Pitard 12 has stated: ""There is no such thing as reliable feasibility studies, unbiased ore grade control, accurate environmental assessments or effective process control, if you cannot identify and minimize the seven (ten) major sources of sampling variability. "" It is these ten sources of sampling variability and the way they arise that are briefly investigated. Variability is measured in terms of variances and rather than being self-compensating, there is good evidence to indicate that they are in fact additive at every step in the sampling and analytical process."

Jan 1, 2014

By M. Karsten

Platinum mines in the Bushveld Complex are located in areas with a high geothermal gradient. This means that, compared to, for example, gold mines of the Witwatersrand region, high rock temperatures are encountered at relatively shallower depths. Thus air cooling and refrigeration need to be considered at early stages in mine development. Another factor that influences air cooling and ventilation requirements is the use of trackless diesel equipment for loading and hauling broken rock. At shallower depths it will be more cost-effective to locate the cooling and ventilation equipment on surface, whereas for deeper mines the more cost-effective option is to locate cooling equipment underground. For intermediate depths, trade-off studies need to be undertaken to determine the optimum mix between more cooling and less air or more air and less cooling, as well as the optimum location for this cooling equipment. Factors that are taken into account include power requirements, positional efficiency, and additional infrastructure requirements. Traditionally the approach has been to ventilate ?all of the mine all of the time?. However, with increasing power costs and growing pressure to ensure sustainability, this strategy must be modified to apply ventilation and cooling on demand. In other words, both cooling and ventilation equipment should be operated only when needed and should be adjusted to the demand at the time. Obviously there will be areas that will need to be ventilated (and cooled) continuously (for example, for dilution of flammable gases), but this can be built in to the overall strategy. In addition, in devising ventilation on demand (VoD) strategies, occupational criteria relating to exposure to gases, noise, and heat need to be taken into account. This paper discusses options available for implementing energy-efficient ventilation and cooling systems and suggests ways of changing traditional thinking in the overall ventilation and cooling of mines. Efficient ventilation and cooling designs can play a major role in improving sustainability and reducing energy costs and carbon footprint.

Jan 1, 2012

By R. Asamoah, P. Forson, S. Xu, W. Skinner, M. Zanin

In most auriferous hydrothermal deposits, gold is preferentially associated with pyrite and arsenopyrite minerals, with higher economic gold values noted for the latter and arsenian pyrite minerals. In this paper, surface (Cryo-XPS) and solution (EDTA extraction) analysis were used to characterise pyrite and arsenopyrite minerals under different aqueous conditions involving electrokinetic study and collector interactions to better understand ways of improving the separation of pyrite and arsenopyrite. The evidence showed higher surface oxidation at solution pulp pH values in the range of 4-11 for arsenopyrite relative to pyrite. The observed highest ratio of pyrite to arsenopyrite selectivity was 1.7 at collector concentration of 50 g/t and decreased with an increase in collector concentration. Keywords: EDTA extractable iron, selectivity index, differential flotation, grade engineering

Jan 1, 2020

By C. Mueller

In many automated mines, multi media video and audio funtionality has to be combined with sensor information or steering commands, which is the idea of a new, PC based integrated and multi media capable control system. The new control system (Multimedia Control - MMC) bases entirely on TCP/IP networking and internet technology. For the first time, this enables the ‘intelligent’ use of video and audio information: pictures and voice sequences may be forwarded on request only, they may be stored if particular events occur (e.g. video black boxes) and sensor signals as well as actions from the automation system can directly be assigned with multi media sequences. MultiMedia Control entirely bases on object oriented software. It uses most modern software technology. As user interface, only a standard web browser is required. This makes the handling of different machines easy. By using mobile web pads, dedicated local operator interfaces are not required any longer. The service staff just connects to the automated equipment by – wireless –LAN to make required adjustments. Customization is easy using an open Application Programming Interface. Software modules may be added to the system without touching or recompiling existing components. The system was prototyped in 2000 using a demo-application. The performance tests showed very positive results both regarding the control system behaviour and the speed/latency timing behaviour of the multi-media information processed. The system now is slightly reshaped to completely meet the final product requirements. It is expected to be available by the end of 2001. Key words: Machine Automation; Control System; Multi Media; Remote Control; Teleoperation; Ethernet; TCP/IP; Internet Technology; Streaming Video; Quality Assurance; Service; Control Centre.

Sep 1, 2001

By DeVerle P. Harris, David E. Euresty

"Potential metal supply refers to metals to be produced from as yet unknown deposits. Naturally, to measure potential supply requires, among other things, inference to the number of deposits, their tonnage, and their grade Thus, probability distributions were constructed for each 400-square mile cell in Northern Sonora, Mexico. A computer system was developed that simulated the occurrence of deposits for each cell, exploration for the deposits, and their exploitation. Evaluation was performed for each deposit by discounted cash flow analysis.An objective of this study was to explore the effect of the transportation network and required road or railroad construction upon potential supply. Consequently, the evaluation system was designed to consider the spatial location of a simulated deposit to the existing transportation network and the market destination. The construction of linkages to connect the deposit to existing transportation arteries as well as the carrying of the concentrates to the intended market were simulated. in terms of cost. The selection of the path took into account the existing terrain. This was done by digitizing topographical maps and representing the topography of the area by an orthogonal grid of elevations. The optimum route was selected by dynamic programming, meeting a prescribed gradient constraint. The potential supply of each cell was determined, allowing for the infrastructure effect."

Jan 1, 2014

By D. Marcotte, R. V. Dutaut

In most exploration or mining grade data-sets, the presence of outliers or extreme values represents a significant challenge to mineral resource estimators. The most common practice is to cap the extreme values at a predefined level. A new capping approach is presented that uses QA/QC coarse duplicate data correlation to predict the real data coefficient of variation (i.e., error-free CV). The cap grade is determined such that the capped data has a CV equal to the predicted CV. The robustness of the approach with regard to original core assay length decisions, departure from lognormality, and capping before or after compositing is assessed using simulated data-sets. Real case studies of gold and nickel deposits are used to compare the proposed approach to the methods most widely used in industry. The new approach is simple and objective. It provides a cap grade that is determined automatically, based on predicted CV, and takes into account the quality of the assay procedure as determined by coarse duplicates correlation.

May 1, 2021

By H. Jiang, W. Wang, Y. Zhao, J. Qiao, C. Duan

DEM simulations were used in this research to study the screening process of a novel variable amplitude equal thickness vibration screen (VAETVS). The response regularity of mass distribution and granular moving velocity at the different screen panels to feed rate was investigated and the predictive model for the unit area processing load was proposed. The influence of aperture size, the size variance, and the opening ratio on the mass passing-distribution and overall screening performance, respectively, were revealed. The results showed that the response model of the unit area load Ф to the feed rate Q can be concluded as Ф∝0.324×Q. The moving velocity of particles also showed a positive relevance to the feed rate, besides which the passing rate of fine-grained material at the feed end was negatively related to the aperture size, while the case was reversed in the feed end. The increase of aperture variance AV enhanced the passing ability of small particles at the feed end,and reduced the misplaced ratio of the large particles at the discharge end. A better screening efficiency can be obtained when the average aperture size of the entire sieve is 7.5 mm, with the aperture variance of 1 mm between the adjacent panels. When the combination of the opening ratio is 35-35-40, a better screening effect can be achieved. Keywords: Equal thickness screening, DEM, particulate velocity, mass distribution regulation

Jan 1, 2020

By B. Maybee, J. Venter, J. Wesseloo

The selection of open-pit slope angles involves high-value decisions with small changes in slope angle, often representing significant changes in net present value. The existing methods used to define design acceptance criteria have evolved from factor of safety to probability of failure (P[F]) to risk consequence to risk frontiers, which represents current state of the art. Current design acceptance measures are based on references to published tables representing the experience and judgement of their authors, who did not specify the purpose of the measures contained therein. As the purpose of the published design acceptance criteria is not specified (i.e., definite stability, marginal stability, optimization, etc.), such tables cannot be used to achieve optimum slope angles that maximize profitability. This paper develops a design acceptance criterion that maximizes profitability by defining a formulation for optimum risk that balances expected risk and reward. The model developed is titled the Mining Risk Model (MRM), and is applied to open-pit slope angle selection through an equation for optimum probability of downside (P[D]O) that balances the upside or opportunity, the P[F], and the downside impact. This formulation for optimum risk is unique, as many authors have presented objective functions for their risk models that can be optimized, but none of the sources reviewed contained a formulation for optimum risk. The MRM is sufficiently flexible to allow the design performance measure that drives P[F], and hence P[D]O, to be selected based on the intended goal. Furthermore, the essential information that must be known to quantify optimum risk is defined. This allows users to determine what information to collect for optimum risk decisions. A further benefit of the MRM is that slope angle decisions and pit shells can be ranked to select the best option, and a threshold is provided that separates acceptable from unacceptable decisions. Finally, the workflow and information required to determine optimum risk are presented.

Sep 9, 2024

By K. Koruyan

Although remote sensing technology has been available for many years, it has rarely been used for monitoring mining activity. Recent studies indicate that remote sensing is also a valuable tool for managing and planning certain aspects of the mining operation. In this paper, we examine areal expansion of marble quarries and the affected vegetation over a period of 10 years in the Mugla region in Turkey, using geographic information system (GIS) and remote sensing (RS) techniques. Images captured by ASTER Level 3A01 (3D Ortho Data Set), Landsat 5, and Landsat 7 satellites between 2001 and 2009 were used for the analysis. Changes in the natural vegetation as a function of the production level in the marble quarry were calculated using the normalized difference vegetation index. According to the study results, land cover and natural vegetation decreased by less than 3 per cent and 1 per cent respectively between 2001 and 2009, following an upsurge in mining activity in the region.

Jan 1, 2012

By K. Lomberg

In this paper the process of sampling and assaying as it relates in particular to the platinum group elements (PGEs) is presented. A discussion of the geology of PGE deposits is included to provide an understanding of the mineralization that is considered necessary prior to sampling, as this has a direct bearing on the mineral resource estimate and also the selection of an appropriate mining cut. The discussion includes the selection of the sampling technique (drilling or face sampling), the size of the sample relating to the requirements of the laboratory, the potential mining cut, as well as a reference to sampling theory. The selection of an assay technique that is appropriate and will yield the optimal result based on sample turnaround, precision, accuracy, and cost is then considered. Examples are drawn from work undertaken on the Bushveld Complex (Merensky Reef, UG2 Chromitite Layer, Platreef) and Great Dyke (Main Sulphide Zone). A discussion of the appropriate QA/QC programme includes the chain of custody, CRM selection and the QA/QC process. Keywords sampling, assaying, QA/QC, platinum group elements.

Jan 1, 2014

The Barrick North Mara Mine and the Advanced Systems Group at SGS Minerals collaborated on the implementation of a grinding expert system for the control and optimisation of a single semi autogenous (SAG) mill. Over the last 5 years, grinding expert control has gained wide acceptance by mineral processors. In this paper, two key factors for success are highlighted: the adaptability of the software tools and the interaction with site personnel. Created with SGS?s MET expert console (MEC) toolkit, and running on Gensym?s G2 real time inference software, the North Mara expert logic has been set up to keep a steady and on spec leaching feed slurry while striving to maximize throughput. Leach feed stability was achieved by standardizing operating practices across shifts; a result of successful collaboration with site personnel in developing a consistent control strategy. The strategy maintains the SAG load and power draw in an optimised range by manipulating SAG feed rates and inlet water flow. The project life-cycle was slightly longer than average due to site specific constraints. One of these was the high turnover rate of site?s workforce during the project, coupled with the availability of key staff on site due to the fly in fly out work roster. These constraints called for different, and innovative ways of project commissioning and hand-over. This paper describes details of the control solution, its implementation as well as results and conclusions.

Jan 1, 2009